Define nvmem-cells and convert mtd-mac-address to nvmem implementation.
The conversion is done with an automated script.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
When the AVM FRITZ!Repeater 1200 was introduced on Kernel 4.19, the
at803x PHY driver incorrectly set up the delays, not disabling delays
set by the bootloader.
The PHY was always operating with RX as well as TX delays enabled, but
with kernel 5.4 and later, the required TX delay is disabled, breaking
ethernet operation.
Correct the PHY mode, so the driver enables both delays.
Signed-off-by: David Bauer <mail@david-bauer.net>
The mx25l25635f supports clock speed up to 50Mhz.
Also remove obsolete "mx25l25635f" hack and rename
the matching device-tree flash node.
Signed-off-by: Dmitry Tunin <hanipouspilot@gmail.com>
[mention node rename as well. chip is very very likely
always the "f" revision for all NBG6617]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
sysupgrade metadata is not flashed to the device, so check-size
should be called _before_ adding metadata to the image.
While at it, do some obvious wrapping improvements.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Acked-by: Paul Spooren <mail@aparcar.org>
Though not strictly necessary, add the closing symbol to make the
job easier for future developers editing this file.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
When support for Luma WRTQ-329ACN was added, the instructions for
flashing this device include using tools from uboot-envtools package.
Unfortunately the OpenWrt buildroot system omits packages from
DEVICE_PACKAGES when CONFIG_TARGET_MULTI_PROFILE,
CONFIG_TARGET_PER_DEVICE_ROOTFS, CONFIG_TARGET_ALL_PROFILES are set. In
result the official images are without tools mentioned in the
instruction. The workoround for the fashing would be installing
uboot-envtools when booted with initramfs image, but not always the
access to internet is available. The other method would be to issue the
necesary command in U-Boot environment but some serial terminals default
configuration don't work well with pasting lines longer than 80 chars.
Therefore add uboot-envtools to default packages, which adds really
small flash footprint to rootfs, where increased size usually is not an
issue.
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Many people appear to use an unneeded "+" prefix for the increment
when calculating a MAC address with macaddr_add. Since this is not
required and used inconsistently [*], just remove it.
[*] As a funny side-fact, copy-pasting has led to almost all
hotplug.d files using the "+", while nearly all of the
02_network files are not using it.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This adds support for the Netgear WAC510 Insight Managed Smart Cloud
Wireless Access Point, an indoor dual-band, dual-radio 802.11ac
business-class wireless AP with integrated omnidirectional antennae
and two 10/100/1000 Mbps Ethernet ports.
For more information see:
<https://www.netgear.com/business/wifi/access-points/wac510>
Specifications:
SoC: Qualcomm IPQ4018 (DAKOTA) ARM Quad-Core
RAM: 256 MiB
Flash1: 2 MiB Winbond W25Q16JV SPI-NOR
Flash2: 128 MiB Winbond W25N01GVZEIG SPI-NAND
Ethernet: Built-in IPQ4018 (SoC, QCA8072 PHY), 2x 1000/100/10 port,
WAN port active IEEE 802.3af/at PoE in
Wireless1: Built-in IPQ4018 (SoC) 802.11b/g/n 2x2:2, 3 dBi antennae
Wireless2: Built-in IPQ4018 (SoC) 802.11a/n/ac 2x2:2, 4 dBi antennae
Input: (Optional) Barrel 12 V 2.5 A Power, Reset button SW1
LEDs: Power, Insight, WAN PoE, LAN, 2.4G WLAN, 5G WLAN
Serial: Header J2
1 - 3.3 Volt (Do NOT connect!)
2 - TX
3 - RX
4 - Ground
WARNING: The serial port needs a TTL/RS-232 3.3 volt level converter!
The Serial settings are 115200-8-N-1.
Installation via Stock Web Interface:
BTW: The default factory console/web interface login user/password are
admin/password.
In the web interface navigating to Management - Maintenance - Upgrade -
'Firmware Upgrade' will show you what is currently installed e.g.:
Manage Firmware
Current Firmware Version: V5.0.10.2
Backup Firmware Version: V1.2.5.11
Under 'Upgrade Options' choose Local (alternatively SFTP would be
available) then click/select 'Browse File' on the right side, choose
openwrt-ipq40xx-generic-netgear_wac510-squashfs-nand-factory.tar
and hit the Upgrade button below. After a minute or two your browser
should indicate completion printing 'Firmware update complete.' and
'Rebooting AP...'.
Note that OpenWrt will use the WAN PoE port as actual WAN port
defaulting to DHCP client but NOT allowing LuCI access, use LAN port
defaulting to 192.168.1.1/24 to access LuCI.
Installation via TFTP Requiring Serial U-Boot Access:
Connect to the device's serial port and hit any key to stop autoboot.
Upload and boot the initramfs based OpenWrt image as follows:
(IPQ40xx) # setenv serverip 192.168.1.1
(IPQ40xx) # setenv ipaddr 192.168.1.2
(IPQ40xx) # tftpboot openwrt-ipq40xx-generic-netgear_wac510-initramfs-fit-uImage.itb
(IPQ40xx) # bootm
Note: This only runs OpenWrt from RAM and has not installed anything
to flash as of yet. One may permanently install OpenWrt as follows:
Check the MTD device number of the active partition:
root@OpenWrt:/# dmesg | grep 'set to be root filesystem'
[ 1.010084] mtd: device 9 (rootfs) set to be root filesystem
Upload the factory image ending with .ubi to /tmp (e.g. using scp or
tftp). Then flash the image as follows (substituting the 9 in mtd9
below with whatever number reported above):
root@OpenWrt:/# ubiformat /dev/mtd9 -f /tmp/openwrt-ipq40xx-generic-netgear_wac510-squashfs-nand-factory.ubi
And reboot.
Dual Image Configuration:
The default U-Boot boot command bootipq uses the U-Boot environment
variables primary/secondary to decide which image to boot. E.g.
primary=0, secondary=3800000 uses rootfs while primary=3800000,
secondary=0 uses rootfs_1.
Switching their values changes the active partition. E.g. from within
U-Boot:
(IPQ40xx) # setenv primary 0
(IPQ40xx) # setenv secondary 3800000
(IPQ40xx) # saveenv
Or from a OpenWrt userspace serial/SSH console:
fw_setenv primary 0
fw_setenv secondary 3800000
Note that if you install two copies of OpenWrt then each will have its
independent configuration not like when switching partitions on the
stock firmware.
BTW: The kernel log shows which boot partition is active:
[ 2.439050] ubi0: attached mtd9 (name "rootfs", size 56 MiB)
vs.
[ 2.978785] ubi0: attached mtd10 (name "rootfs_1", size 56 MiB)
Note: After 3 failed boot attempts it automatically switches partition.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
[squashed netgear-tar commit into main and rename netgear-tar for
now, until it is made generic.]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The routerbootparts driver dynamically discovers the location of MikroTik
partitions, but it cannot determine their size (except by extending them
up to the start of the next discovered partition).
The hard_config partition has a default size of 0x1000 in the driver,
while it actually takes 0x2000 on the hAP-ac2. Set the correct size in
the hAP-ac2 DTS.
On most devices, this isn't a problem as the actual data fits in 0x1000
bytes. However, some devices have larger data that doesn't fit in 0x1000
bytes. In any case, all devices seen so far have enough space for a
0x2000 hard_config partition before the start of the dtb_config partition.
With the current 0x1000 size:
0x00000000e000-0x00000000f000 : "hard_config"
0x000000010000-0x000000017bbc : "dtb_config"
With this patch extending the size to 0x2000:
0x00000000e000-0x000000010000 : "hard_config"
0x000000010000-0x000000017bbc : "dtb_config"
Other ipq40xx boards may need the same fix but it needs testing.
References: https://forum.openwrt.org/t/support-for-mikrotik-hap-ac2/23333/324
Acked-by: Thibaut VARÈNE <hacks@slashdirt.org>
Signed-off-by: Baptiste Jonglez <git@bitsofnetworks.org>
Manually rebased*
generic/backport-5.4/700-v5.5-net-core-allow-fast-GRO-for-skbs-with-Ethernet-heade.patch
Added new backport*
generic/backport-5.4/050-gro-fix-napi_gro_frags-Fast-GRO-breakage-due-to-IP-a.patch
All others updated automatically.
The new backport was included based on this[1] upstream commit that will be
mainlined soon. This change is needed because Eric Dumazet's check for
NET_IP_ALIGN (landed in 5.4.114) causes huge slowdowns on drivers which use
napi_gro_frags().
Build system: x86_64
Build-tested: ipq806x/R7800
Run-tested: ipq806x/R7800
No dmesg regressions, everything functional
*Credit to Alexander Lobakin
1. https://git.kernel.org/pub/scm/linux/kernel/git/netdev/net.git/commit/?id=7ad18ff6449cbd6beb26b53128ddf56d2685aa93
Signed-off-by: John Audia <graysky@archlinux.us>
This commit adds support for the MikroTik SXTsq 5 ac (RBSXTsqG-5acD),
an outdoor 802.11ac wireless CPE with one 10/100/1000 Mbps Ethernet
port.
Specifications:
- SoC: Qualcomm Atheros IPQ4018
- RAM: 256 MB
- Storage: 16 MB NOR
- Wireless: IPQ4018 (SoC) 802.11a/n/ac 2x2:2, 16 dBi antennae
- Ethernet: IPQ4018 (SoC) 1x 10/100/1000 port, 10-28 Vdc PoE in
- 1x Ethernet LED (green)
- 7x user-controllable LEDs
· 1x power (blue)
· 1x user (green)
· 5x rssi (green)
Note:
Serial UART is probably available on the board, but it has not been
tested.
Flashing:
Boot via TFTP the initramfs image. Then, upload a sysupgrade image
via SSH and flash it normally. More info at the "Common procedures
for MikroTik products" page https://openwrt.org/toh/mikrotik/common.
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
Some targets select HZ=100, others HZ=250. There's no reason to select a higher
timer frequency (and 100 Hz are available in every architecture), so change all
targets to 100 Hz.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
For the targets which enable ubifs, these symbols are already part of the
generic kconfigs. Drop them from the target kconfigs.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
This adds support for the MikroTik RouterBOARD RBD52G-5HacD2HnD-TC
(hAP ac²), a indoor dual band, dual-radio 802.11ac
wireless AP with integrated omnidirectional antennae, USB port and five
10/100/1000 Mbps Ethernet ports.
See https://mikrotik.com/product/hap_ac2 for more info.
Specifications:
- SoC: Qualcomm Atheros IPQ4018
- RAM: 128 MB
- Storage: 16 MB NOR
- Wireless:
· Built-in IPQ4018 (SoC) 802.11b/g/n 2x2:2, 2.5 dBi antennae
· Built-in IPQ4018 (SoC) 802.11a/n/ac 2x2:2, 2.5 dBi antennae
- Ethernet: Built-in IPQ4018 (SoC, QCA8075) , 5x 1000/100/10 port,
passive PoE in
- 1x USB Type A port
Installation:
Boot the initramfs image via TFTP and then flash the sysupgrade
image using "sysupgrade -n"
Signed-off-by: Robert Marko <robimarko@gmail.com>
The bootloader of many ipq40xx boards seems to require the config node
of the FIT image to be 'config@1' (or a secific different value).
This requirement used to be implicitely satisfied because OpenWrt used
to also call the configuration node inside a FIT image 'config@1'.
However, as recent U-Boot now prohibits the use of the '@' symbol as
part of node names, this was changed by
commit 5ec60cbe9d ("scripts: mkits.sh: replace @ with - in nodes")
Explicitely restore the default name of the configuration node to
'config@1' on ipq40xx.
Reported-by: Chen Minqiang <ptpt52@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
So far, board.d files were having execute bit set and contained a
shebang. However, they are just sourced in board_detect, with an
apparantly unnecessary check for execute permission beforehand.
Replace this check by one for existance and make the board.d files
"normal" files, as would be expected in /etc anyway.
Note:
This removes an apparantly unused '#!/bin/sh /etc/rc.common' in
target/linux/bcm47xx/base-files/etc/board.d/01_network
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
While rebasing into setting bits instead of magic values,
I accidentally forgot to actually set the force bit.
Without it using the pins as GPIO-s did not actually work.
Fixes: b5c93ed ("ipq40xx: add Qualcomm QCA807x driver")
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
5.4.102 backported a lot of stuff that our WireGuard backport already
did, in addition to other patches we had, so those patches were
removed from that part of the series. In the process other patches were
refreshed or reworked to account for upstream changes.
This commit involved `update_kernel.sh -v -u 5.4`.
Cc: John Audia <graysky@archlinux.us>
Cc: David Bauer <mail@david-bauer.net>
Cc: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
The variables KERNEL_INITRAMFS_PREFIX and KERNEL_PREFIX are already
defined in include/image.mk and don't have to be redefined in the
target Makefiles.
Signed-off-by: Paul Spooren <mail@aparcar.org>
[also cover imx6]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
On a platform with many very different devices, like found on ipq40xx,
the generic profile seems like a remnant of the past that does not
have a real use anymore.
Remove it to have one thing less to maintain.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Acked-by: Paul Spooren <mail@aparcar.org>
The majority of our targets provide a default value for the variable
SUPPORTED_DEVICES, which is used in images to check against the
compatible on a running device:
SUPPORTED_DEVICES := $(subst _,$(comma),$(1))
At the moment, this is implemented in the Device/Default block of
the individual targets or even subtargets. However, since we
standardized device names and compatible in the recent past, almost
all targets are following the same scheme now:
device/image name: vendor_model
compatible: vendor,model
The equal redundant definitions are a symptom of this process.
Consequently, this patch moves the definition to image.mk making it
a global default. For the few targets not using the scheme above,
SUPPORTED_DEVICES will be defined to a different value in
Device/Default anyway, overwriting the default. In other words:
This change is supposed to be cosmetic.
This can be used as a global measure to get the current compatible
with: $(firstword $(SUPPORTED_DEVICES))
(Though this is not precisely an achievement of this commit.)
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Since generic images have been split to their own
Makefile boards are showing up twice in menuconfig
as $(eval $(call BuildImage)) was not dropped from
the new generic.mk.
Hence $(eval $(call BuildImage)) was being called
twice.
So, lets simply drop it from generic.mk.
Fixes: 378c7ff282 ("ipq40xx: split generic images into own file")
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
This enables the MikroTik platform driver, it enables us to parse
valuable info from hard_config including WLAN calibration data
extraction from sysfs.
Signed-off-by: Robert Marko <robimarko@gmail.com>
This enables the new MikroTik specific partition parser.
This avoids manually specifying the MikroTik specific partitions as they
can be detected by their magic values.
Signed-off-by: Robert Marko <robimarko@gmail.com>
MikroTik devices require the use of raw vmlinux out of the self
extracting compressed kernels.
They also require 4K sectors, kernel2minor, partition parser as well as
RouterBoard platform drivers.
So in order to not add unnecessary code to the generic sub target lets
introduce a MikroTik sub target.
Signed-off-by: Robert Marko <robimarko@gmail.com>
If the watchdog is enabled, set the timeout to 30 seconds before
decompress is started.
Mikrotik ipq40xx devices running with RouterBoot have the SoC watchdog
enabled and running with a timeout that does not allow time for the
kernel to decompress and manage the watchdog.
On ipq40xx RouterBoot TFTP boot the watchdog countdown is reset before:
Jumping to kernel
Signed-off-by: John Thomson <git@johnthomson.fastmail.com.au>
This adds a appended_dtb section to the ARM decompressor
linker script.
This allows using the existing ARM zImage appended DTB support for
appending a DTB to the raw ELF kernel.
Its size is set to 1MB max to match the zImage appended DTB size limit.
To use it to pass the DTB to the kernel, objcopy is used:
objcopy --set-section-flags=.appended_dtb=alloc,contents \
--update-section=.appended_dtb=<target>.dtb vmlinux
This is based off the following patch:
c063e27e02
Signed-off-by: Robert Marko <robimarko@gmail.com>
Both devices use u-boot env variables to boot OpenWrt from its flash
partition. Using u-boot envtools, it is possible to change the bootcmd
back to the stock firmware partition directly from OpenWrt without
attaching a serial cable or even physically accessing the device.
Signed-off-by: Jan Alexander <jan@nalx.net>
DTS files do not need to be executable. 644 is enough.
Fixes: 0fbdb51f76 ("ipq40xx: add Edgecore OAP-100 support")
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
[split by targets]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Since updating the MDIO driver, the probe will fail hard on any
PHY not present on the bus, while this was not the case prior.
Fixes commit 26b1f72381 ("ipq40xx: net: phy: ar40xx: remove PHY
handling")
Signed-off-by: David Bauer <mail@david-bauer.net>
Specifications:
SOC: Qualcomm IPQ4018 (DAKOTA) ARM Quad-Core
RAM: 256 MiB
FLASH1: 4 MiB NOR
FLASH2: 128 MiB NAND
ETH: Qualcomm QCA8075
WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11b/g/n 2x2
WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11n/ac W2 2x2
INPUT: Reset
LED: Power, Internet
UART1: On board pin header near to LED (3.3V, TX, RX, GND), 3.3V without pin - 115200 8N1
OTHER: On board with BLE module - by cp210x USB serial chip
On board hareware watchdog with GPIO0 high to turn on, and GPIO4 for watchdog feed
Install via uboot tftp or uboot web failsafe.
By uboot tftp:
(IPQ40xx) # tftpboot 0x84000000 openwrt-ipq40xx-generic-glinet_gl-ap1300-squashfs-nand-factory.ubi
(IPQ40xx) # run lf
By uboot web failsafe:
Push the reset button for 10 seconds util the power led flash faster,
then use broswer to access http://192.168.1.1
Afterwards upgrade can use sysupgrade image.
Signed-off-by: Dongming Han <handongming@gl-inet.com>
Lets use the generic upstream phy_print_status() instead of doing
something similar by hand.
Before:
ess_edma c080000.edma: eth1: GMAC Link is up with phy_speed=1000
After:
ess_edma c080000.edma eth1: Link is Up - 1Gbps/Full - flow control rx/tx
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Since we now have a proper PHY driver for QCA807x and AR803x has already
been supported properly there is no need for the driver to be poking
on PHY registers for ethtool ops.
So, lets simply use the generic
phy_ethtool_ksettings_get/phy_ethtool_ksettings_set functions.
This also has the advantage of properly populating stuff other than
speeds like, transceiver type, MDI-X etc.
ethtool before:
root@OpenWrt:/# ethtool eth1
Settings for eth1:
Supported ports: [ TP MII ]
Supported link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Full
1000baseX/Full
Supported pause frame use: Symmetric Receive-only
Supports auto-negotiation: Yes
Supported FEC modes: Not reported
Advertised link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Full
1000baseX/Full
Advertised pause frame use: Symmetric Receive-only
Advertised auto-negotiation: Yes
Advertised FEC modes: Not reported
Link partner advertised link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Full
Link partner advertised pause frame use: No
Link partner advertised auto-negotiation: No
Link partner advertised FEC modes: Not reported
Speed: 1000Mb/s
Duplex: Full
Port: Twisted Pair
PHYAD: 4
Transceiver: internal
Auto-negotiation: on
MDI-X: Unknown
Supports Wake-on: d
Wake-on: d
Current message level: 0x00000000 (0)
Link detected: yes
ethtool after:
root@OpenWrt:/# ethtool eth1
Settings for eth1:
Supported ports: [ TP MII ]
Supported link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Full
1000baseX/Full
Supported pause frame use: Symmetric Receive-only
Supports auto-negotiation: Yes
Supported FEC modes: Not reported
Advertised link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Full
1000baseX/Full
Advertised pause frame use: Symmetric Receive-only
Advertised auto-negotiation: Yes
Advertised FEC modes: Not reported
Link partner advertised link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Full
Link partner advertised pause frame use: Symmetric Receive-only
Link partner advertised auto-negotiation: Yes
Link partner advertised FEC modes: Not reported
Speed: 1000Mb/s
Duplex: Full
Port: Twisted Pair
PHYAD: 4
Transceiver: external
Auto-negotiation: on
MDI-X: off (auto)
Supports Wake-on: d
Wake-on: d
Current message level: 0x00000000 (0)
Link detected: yes
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Since the new PHY driver manages each PHY individually and therefore
registers each PHY that is marked with gpio-controller; DT property as a
GPIO controller we need to convert old DT bindings to account for this.
Only 2 boards use this so its not much of an issue.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
This adds necessary DT properties for QCA807x PHY-s to IPQ4019 DTSI.
Also adds the PSGMII PHY as it wont get probed otherwise.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
PHY needs to be soft reset before starting it from ethernet driver as
AR40xx calibration will leave it in unwanted state.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Since we now have proper PHY driver for the QCA807x PHY-s, lets remove
PHY handling from AR40xx.
This removes PHY driver, PHY GPIO driver and PHY init code.
AR40xx still needs to handle PSGMII calibration as that requires R/W
from the switch, so I am unable to move it into PHY driver.
This also converted the AR40xx driver to use OF_MDIO to find the MDIO
bus as it now cant be set through the PHY driver.
So lets depend on OF_MDIO in KConfig.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
This adds driver for the Qualcomm QCA8072 and QCA8075 PHY-s.
They are 2 or 5 port IEEE 802.3 clause 22 compliant
10BASE-Te, 100BASE-TX and 1000BASE-T PHY-s.
They feature 2 SerDes, one for PSGMII or QSGMII connection with MAC,
while second one is SGMII for connection to MAC or fiber.
Both models have a combo port that supports 1000BASE-X and 100BASE-FX
fiber.
Each PHY inside of QCA807x series has 2 digitally controlled output only
pins that natively drive LED-s.
But some vendors used these to driver generic LED-s controlled by
user space, so lets enable registering each PHY as GPIO controller and
add driver for it.
This also adds the ability to specify DT properties so that 1000 Base-T
LED will also be lit up for 100 and 10 Base connections.
This is usually done by U-boot, but boards running mainline U-boot are
not configuring this yet.
These PHY-s are commonly used in Qualcomm IPQ40xx, IPQ60xx and IPQ807x
boards.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
With the reworked MDIO driver, EDMA will fail to get the MII BUS as it
used the MII BUS stored inside the MDIO structure private data.
This obviously does not work with the modernized driver, so lets switch
to using a purpose build of_mdio_find_bus() which will return the MII
BUS and only requires the MDIO node to be passed.
This is easy as we already have the node parsed.
Also, since we now require OF_MDIO add that as dependency.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
IPQ40xx MDIO driver was upstreamed in kernel version 5.8.
So lets backport the upstream version and drop our local one.
This also refreshed the kernel config since the symbol name has changed.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
SOC: IPQ4018 / QCA Dakota
CPU: Quad-Core ARMv7 Processor rev 5 (v71) Cortex-A7
DRAM: 256 MiB
NOR: 32 MiB
ETH: Qualcomm Atheros QCA8075 (2 ports)
PLC: MaxLinear G.hn 88LX5152
WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2
WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2
INPUT: RESET, WiFi, PLC Button
LEDS: red/white home, white WiFi
To modify a retail device to run OpenWRT firmware:
1) Setup a TFTP server on IP address 192.168.0.100 and copy the OpenWRT
initramfs (initramfs-fit-uImage.itb) to the TFTP root as 'uploadfile'.
2) Power on the device while pressing the recessed reset button next to
the Ethernet ports. This causes the bootloader to retrieve and start
the initramfs.
3) Once the initramfs is booted, the device will come up with IP
192.168.1.1. You can then connect through SSH (allow some time for
the first connection).
4) On the device shell, run 'fw_printenv' to show the U-boot environment.
Backup this information since it contains device unique factory data.
5) Change the boot command to support booting OpenWRT:
# fw_setenv bootcmd 'sf probe && sf read 0x84000000 0x180000 0x400000 && bootm'
6) Change directory to /tmp, download the sysupgrade (e.g. through wget)
and install it with sysupgrade. The device will reboot into OpenWRT.
Notice that there is currently no support for booting the G.hn chip.
This requires userland software we lack the rights to share right now.
Signed-off-by: Stefan Schake <stefan.schake@devolo.de>
Device specifications:
* QCA IPQ4019
* 256 MB of RAM
* 32 MB of SPI NOR flash (w25q256)
- 2x 15 MB available; but one of the 15 MB regions is the recovery image
* 2T2R 2.4 GHz
- QCA4019 hw1.0 (SoC)
- requires special BDF in QCA4019/hw1.0/board-2.bin with
bus=ahb,bmi-chip-id=0,bmi-board-id=20,variant=PlasmaCloud-PA2200
* 2T2R 5 GHz (channel 36-64)
- QCA9888 hw2.0 (PCI)
- requires special BDF in QCA9888/hw2.0/board-2.bin
bus=pci,bmi-chip-id=0,bmi-board-id=16,variant=PlasmaCloud-PA2200
* 2T2R 5 GHz (channel 100-165)
- QCA4019 hw1.0 (SoC)
- requires special BDF in QCA4019/hw1.0/board-2.bin with
bus=ahb,bmi-chip-id=0,bmi-board-id=21,variant=PlasmaCloud-PA2200
* GPIO-LEDs for 2.4GHz, 5GHz-SoC and 5GHz-PCIE
* GPIO-LEDs for power (orange) and status (blue)
* 1x GPIO-button (reset)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x gigabit ethernet
- phy@mdio3:
+ Label: Ethernet 1
+ gmac0 (ethaddr) in original firmware
+ used as LAN interface
- phy@mdio4:
+ Label: Ethernet 2
+ gmac1 (eth1addr) in original firmware
+ 802.3at POE+
+ used as WAN interface
* 12V 2A DC
Flashing instructions:
The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the factory image to the u-boot when the device boots up.
Signed-off-by: Marek Lindner <marek.lindner@kaiwoo.ai>
[sven@narfation.org: prepare commit message, rebase, use all LEDs, switch
to dualboot_datachk upgrade script, use eth1 as designated WAN interface]
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Device specifications:
* QCA IPQ4018
* 256 MB of RAM
* 32 MB of SPI NOR flash (w25q256)
- 2x 15 MB available; but one of the 15 MB regions is the recovery image
* 2T2R 2.4 GHz
- QCA4019 hw1.0 (SoC)
- requires special BDF in QCA4019/hw1.0/board-2.bin with
bus=ahb,bmi-chip-id=0,bmi-board-id=16,variant=PlasmaCloud-PA1200
* 2T2R 5 GHz
- QCA4019 hw1.0 (SoC)
- requires special BDF in QCA4019/hw1.0/board-2.bin with
bus=ahb,bmi-chip-id=0,bmi-board-id=17,variant=PlasmaCloud-PA1200
* 3x GPIO-LEDs for status (cyan, purple, yellow)
* 1x GPIO-button (reset)
* 1x USB (xHCI)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x gigabit ethernet
- phy@mdio4:
+ Label: Ethernet 1
+ gmac0 (ethaddr) in original firmware
+ used as LAN interface
- phy@mdio3:
+ Label: Ethernet 2
+ gmac1 (eth1addr) in original firmware
+ 802.3af/at POE(+)
+ used as WAN interface
* 12V/24V 1A DC
Flashing instructions:
The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the factory image to the u-boot when the device boots up.
Signed-off-by: Marek Lindner <marek.lindner@kaiwoo.ai>
[sven@narfation.org: prepare commit message, rebase, use all LEDs, switch
to dualboot_datachk upgrade script, use eth1 as designated WAN interface]
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Other vendors are using functionality similar to the ones OpenMesh used to
implement two areas on the flash to store the default image and a fallback
image. So just change the name to dualboot_datachk.sh to avoid duplicated
code just to have the same script for different vendors.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
