I have not found a scenario that would break by setting the source address on
default, but please let me know if any special considerations should be taken.
Signed-off-by: Kristian Evensen <kristian.evensen at gmail.com>
SVN-Revision: 43582
if the initramfs kernel and payload were flashed in one block, the payload might not be at the start of the ubi partition due to bad blocks inside the kernel partition.
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 43513
KD20 got an IC+ phy, without the driver the phy is not properly
initialized resulting in ethernet not working unless being already
initialized by the vendor loader.
upstream commit 368b4d2b49bbbf379d9334747fbbd2aaaafe4356
drivers: net: remove dead drivers
removed icplus.c due to the lack of in-tree users.
Partially revert that commit adding back the IC+ driver.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 43508
it is now possible to flash a initramfs kernel and a sysupgrade tar file inside the ubi partition. on first boot, the takeover script will find the tar file, extract and finally sysupgrade it. this allows us to flash owrt/ubi images in a 2 phase setup using ODM webuis that are not ubi aware. this is needed by some mediatek and brokencom devices.
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 43505
this can be used on nand flashes and will skip bad blocks and run ecc on the
read data before dumping it.
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 43500
Added complementary blobmsg_close_table() before returning from function
on error.
Signed-off-by: Sławomir Demeszko <s.demeszko@wireless-instruments.com>
SVN-Revision: 43477
In r41872 and r42787 Dynamic VLAN support was reintroduced, but the vlan_bridge
parameter is not read while setting up the config, so the default is used which
is undesirable for some uses.
Signed-off-by: Ben Franske <ben.mm@franske.com>
SVN-Revision: 43473
create user:group before running postinst-pkg. the postinst hook might require
the user:group to already exist.
Signed-off-by: Christian Schoenebeck <christian.schoenebeck@gmail.com>
SVN-Revision: 43472
Packages fdisk and lsblk were missing dependency for libsmartcols.so.1
Add package for libsmartcols and add dependency from fdisk and lsblk.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 43459
perf was in the oldpackages repository, but it makes more sense to have
it part of the default package set since we build it from the Linux
kernel sources.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 43418
Thanks to Dave Taht for debugging and thanks to Comcast for
shipping strangely behaving software so I can fix some corner cases.
Signed-off-by: Steven Barth <steven@midlink.org>
SVN-Revision: 43415
fixes BeagleBoard C4 detection
error message in serial console was:
"WARNING: Could not determine device tree to use"
change is found in upstream u-boot
Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de>
SVN-Revision: 43392
This adds support for the oxnas target in U-Boot 2014.04
History can be found at https://github.com/kref/u-boot-oxnas up to 2013.10
changes from 2013.10 to 2014.04 can be followed at
https://gitorious.org/openwrt-oxnas
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 43389
This is the oxnas target previously developed at
http://gitorious.org/openwrt-oxnas
Basically, this consolidates the changes and addtionas from
http://github.org/kref/linux-oxnas
into a new OpenWrt hardware target 'oxnas' adding support for
PLX Technology NAS7820/NAS7821/NAS7825/...
formally known as
Oxford Semiconductor OXE810SE/OXE815/OX820/...
For now there are 4 supported boards:
Cloud Engines Pogoplug V3 (without PCIe)
fully supported
Cloud Engines Pogoplug Pro (with PCIe)
fully supported
MitraStar STG-212
aka ZyXEL NSA-212,
aka Medion Akoya P89625 / P89636 / P89626 / P89630,
aka Medion MD 86407 / MD 86805 / MD 86517 / MD 86587
fully supported, see http://wiki.openwrt.org/toh/medion/md86587
Shuttle KD-20
partially supported (S-ATA driver lacks support for 2nd port)
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 43388
mtd.c:544:7: warning: format ‘%x’ expects argument of type ‘unsigned int’, but argument 3 has type ‘ssize_t’ [-Wformat]
mtd.c:602:1: warning: label ‘done’ defined but not used [-Wunused-label]
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 43383
1) nand_upgrade_tar: use a simpler condition that matches if () { }
logic and fix check of $kernel_length variable
2) nand_do_upgrade_stage2: use case, otherwise one could believe we
always call nand_upgrade_tar
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 43373
r37490 removed the actual driver but left the kmod definition intact,
causing the build system hapily creating an empty package for it.
Remove it also to not make it seem as if it still exists.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 43316
ldd might be called for shell scrips during sysupgrade, causing it to
complain that they are not a dynamic executables.
This is a harmless error, so supress it to avoid confusing about them
being serious ones.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 43315
ld-musl-*.so* is a symlink "broken" for the hostsystem, so wildcard
will skip it, causing LD_MUSL_NAME to empty and the ldd symlink pointing
to ../../lib directly.
This causes sysupgrade failing to copy any linked libaries and
consequently failing to run anything after switching to ram disk.
Fix this by creating a symlink directly pointing to where ld-musl-*.so*
points to.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 43314
Update nf_conntrack_rtsp to latest version based on http://mike.it-loops.com/rtsp/ (rtsp-module-3.7-v2.tar.gz).
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 43311
* fixes a bug in multipart sms
* adds a new call to read the sim phone number (partially functioanl)
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 43310
r36107 ("base-files: sysupgrade fail with eglibc") tried to fix
sysupgrade by changing the ld-soname to what is expected, but only
fixed MIPS while breaking ARM.
The underlying issue is that the ld.so name varies widely across
different architectures for eglibc:
eglibc-2.19-r25243$ grep -r "ld-soname :=" . | awk '{ print $3 }' | sort -u
ld64.so.1
ld64.so.2
ld-linux-aarch64_be.so.1
ld-linux-aarch64.so.1
ld-linux-armhf.so.3
ld-linux-mipsn8.so.1
ld-linux.so.2
ld-linux.so.3
ld-linux-x32.so.2
ld-linux-x86-64.so.2
ld.so.1
Instead of adding each different soname to check for and copy it,
replace the awk script with a sed script to extract it properly and
drop the hardcoded so-name.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 43295
Starting from kernel version 3.15, the crc32c module was renamed to
crc32c_generic.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 43291
usb-common.ko was moved to drivers/usb/common starting from kernel 3.16
by upstream commit f4cbd33fd5f0587910fa9db403a1b42f1cabf820
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 43290
b52053b 6in4: https support for he.net tunnel api
introduced HTTPS support using wget.
The busybox version of wget, however, doesn't support the -V option,
thus poluting logfiles with a full invalid-parameter-output.
Redirect stderr to fix that.
As libcurl and curl support selecting the SSL library of your choice,
also add support for curl which is more commonly used on OpenWrt than
"real" wget which needs libopenssl.
Also make sure to respect SSL_CERT_DIR and increase timeouts.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 43228
setsid is called fixing the pgrp issue
trigger the wdt while modules are being inserted
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 43193
This will ease adding new targets and updating:
* split UBOOTS var into multiple lines
* remove version from TITLE
Signed-off-by: Nicolas Thill <nico@openwrt.org>
SVN-Revision: 43187
This patch adds the userspace and kernelspace for
- match NETFILTER_XT_MATCH_CLUSTER
This match can be used to deploy gateway and back-end load-sharing clusters.
- target IP_NF_TARGET_CLUSTERIP
This module allows you to configure a simple cluster of nodes
that share a certain IP and MAC address
without an explicit load balancer in front of them.
Connections are statically distributed between the nodes in this cluster.
This is used i.e. by strongswan-ha.
Signed-off-by: Christian Scheele <cs@embedd.com>
SVN-Revision: 43174
Generate a random serial from /dev/urandom when creating selfsigned certs.
Fixes "sec_error_reused_issuer_and_serial" with Firefox.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 43168
Note, that licensing stuff is a nightmare: many packages does not clearly
state their licenses, and often multiple source files are simply copied
together - each with different licensing information in the file headers.
I tried hard to ensure, that the license information extracted into the OpenWRT's
makefiles fit the "spirit" of the packages, e.g. such small packages which
come without a dedicated source archive "inherites" the OpenWRT's own license
in my opinion.
However, I can not garantee that I always picked the correct information
and/or did not miss license information.
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
SVN-Revision: 43155
Port Debians adaptive LCP echo patch to pppd, make it configurable with UCI
and enable it by default.
When adaptive LCP echo is enabled, LCP echo requests are only sent if the
link is idle, this avoids the common situation where a congested PPP link
(e.g. during torrenting) is falsely detected as disconnected because the
LCP replies are not received in time.
Also bump the copyright year in the Makefile, remove a redundant maintainer
entry and fix the shell processing of the keepalive option when the two-
value syntax is used.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 43143
Only list the kernel versions that do not match so that new kernel
versions will automatically match. This improves support for kernel
3.18.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 43132
This patch added stuff that is already there and if it would be needed
this would result in a compile error.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 43131
More recent kernel versions (>= 3.12) support native VXLAN
support.
The Open VSwitch kernel module tries to build using native VXLAN
support if it detects a kernel version >=3.12.
The build works fine, but during startup the OVS kernel module
does not load.
dmesg output is something like this:
[ 1201.262842] openvswitch: Unknown symbol vxlan_sock_release
[ 1201.262949] openvswitch: Unknown symbol vxlan_xmit_skb
[ 1201.263161] openvswitch: Unknown symbol vxlan_sock_add
Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
SVN-Revision: 43126
Using a redirect to a non-empty mtd partition will not erase the
blocks prior to writing to them resulting in broken dsl_fw.
Fix this by piping to mtd write - /dev/mtdX instead.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 43125
HE.net tunnel update API requests are now made via https if an
SSL-capable wget is installed. Certificate validation is
conditionally enabled if the CA certs are available.
Signed-off-by: Andrew Skalski <askalski@gmail.com>
SVN-Revision: 43124
I had to use a VDSL-only tone-setup to get show-time.
Handle this in uci by checking if annex is unset.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 43114
The DHT11 is a temperature and humidity sensor supported by linux
since 3.14.
This patch is tested on recent mxs with kernel 3.14.18.
Signed-off-by: Harald Geyer <harald@ccbib.org>
SVN-Revision: 43103
Currently busybox utils like "ls" fail to display filenames containing UTF-8
characters, replacing any special characters with "?".
Change libbb's printable_string() function to allow high ASCII characters so
that unicode filenames are displayed correctls.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 43084
* Fixes sending an extraneous message body for 204 and 304 resoponses which
breaks Chrome in keep-alive mode.
* Adds mimetypes for JSON and JSONP.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 43078
Package util-linux-dmesg is broken (at least) in Barrier Breaker git repo
as you can select it within menuconfig, it will compile (as a part of
util-linux) but it will not install as install section is missing from
package Makefile.
Signed-off-by: Tomasz Wasiak <tjwasiak@gmail.com>
SVN-Revision: 43069
- Support HT40 instead of HT40+/HT40- like mac80211
- Enable 11n if htmode is HT20 or HT40
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 43063
Based on bug #18206 sysupgrade can lead to loss of password information in
certain situations. Most likely all users who will upgrade from versions
r43017-43040, will lose their current passwords. :-(
https://dev.openwrt.org/ticket/18206
Currently /etc/shadow is defined as a conffile in base-files:
https://dev.openwrt.org/browser/trunk/package/base-files/Makefile#L37
But it is not defined in the default list of essential files to keep in
sysupgrade:
https://dev.openwrt.org/browser/trunk/package/base-files/files/lib/upgrade/keep.d/base-files-essential
If exporting conffiles info fails, /etc/shadow can get lost.
Shadow passwords are now the default, so saying that preserving /etc/passwd
is essential while /etc/shadow is not, makes no sense.
The attached patch adds /etc/shadow to the list of essential files.
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
SVN-Revision: 43061
Attempting to build broadcom_wl (from trunk) with the linaro 4.9.x
toolchain produces the following errors:
<...>/wl_linux.c: In function 'wl_dump_ver':
<...>/wl_linux.c:2302:3: error: macro "__DATE__" might prevent reproducible builds [-Werror=date-time]
__DATE__, __TIME__, EPI_VERSION_STR);
^
<...>/wl_linux.c:2302:13: error: macro "__TIME__" might prevent reproducible builds [-Werror=date-time]
__DATE__, __TIME__, EPI_VERSION_STR);
^
cc1: some warnings being treated as errors
Remove the use of the __DATE__ and __TIME__ macros, as the info is not
really useful.
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
SVN-Revision: 43046
This module is required to read the CPU core temperature sensors
on the Alix APU board.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 43027
The wpa_psk_file option offers the possibility to use a different WPA-PSK key for each client. The directive points to a file with the following syntax:
mac_address wpa_passphrase_or_hex_key
Example:
00:11:22:33:44:55 passphrase_for_client_1
00:11:22:33:44:67 passphrase_for_client_2
00:11:22:33:44:89 0123456789abcdef0123456789abcdef0123456789abcdef0123456789abcdef
So it is possible to specify both ASCII passphrases and raw 64-chars hex keys.
Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>
SVN-Revision: 43001
[base-files] failsafe-mode: print short help on commandline
Like mentioned in ticket https://dev.openwrt.org/ticket/11911
this should make the IRC much quieter. Failsafe is somehow
special and even experienced users are helpless, because they
are not used to this seldom situation. Also: likely you have
no internet access in this mode, so you cannot use the wiki.
a failsafe-session now looks like this:
first we see from 'package/base-files/files/bin/login.sh' the hint:
=== IMPORTANT ============================
Use 'passwd' to set your login password
this will disable telnet and enable SSH
------------------------------------------
after this the /etc/banner ("OpenWrt - wireless freedom")
and then the new text:
================= FAILSAFE MODE active ================
special commands:
* firstboot reset settings to factory defaults
* mount_root mount root-partition with config files
after mount_root:
* passwd change root's password
* /etc/config directory with config files
for more help see:
http://wiki.openwrt.org/doc/howto/generic.failsafe
=======================================================
this supersedes the old patches:
http://patchwork.openwrt.org/patch/3337/http://patchwork.openwrt.org/patch/3553/
Signed-off-by: Bastian Bittorf <bittorf@bluebottle.com>
SVN-Revision: 42985
* Rewrite ndp proxy using kernel proxying
* Aid flash-renumbering in hybrid DHCPv6-mode
* Unicast RAs to RS senders
* Add support for router address
Signed-off-by: Steven Barth <steven@midlink.org>
SVN-Revision: 42944
- Consider not installed feeds as well
- Add option to decide whether to comment disabled feeds
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 42931
Inside every LuCI package you need to clear luci-indexcache and
sometimes when installing non LuCI pacakges it's also needed to clear
it. Easier put it into default_postinst().
Signed-off-by: Christian Schoenebeck <christian.schoenebeck@gmail.com>
SVN-Revision: 42923
Qihoo C301 has 2 flash chips of which one is used as primary and the
other is used as backup. OEM U-Boot will try to boot an activeregion N
with imageNstatus=0 and imageNtrynum <= imagemaxtry. If such a region
is found, bootloader will try to increment imageNtrynum and boot it.
This patch tries to reset imageNtrynum after each successful boot (if
the boot process reaches the execution of /etc/init.d/done).
root@OpenWrt:/# hexdump -C -n 128 /dev/mtdblock9
00000000 9e f3 63 91 61 63 74 69 76 65 72 65 67 69 6f 6e |..c.activeregion|
00000010 3d 31 00 69 6d 61 67 65 31 73 74 61 74 75 73 3d |=1.image1status=|
00000020 30 00 69 6d 61 67 65 32 73 74 61 74 75 73 3d 30 |0.image2status=0|
00000030 00 69 6d 61 67 65 32 74 72 79 6e 75 6d 3d 30 00 |.image2trynum=0.|
00000040 69 6d 61 67 65 6d 61 78 74 72 79 3d 33 00 69 6d |imagemaxtry=3.im|
00000050 61 67 65 31 74 72 79 6e 75 6d 3d 30 00 00 00 00 |age1trynum=0....|
00000060 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
SVN-Revision: 42914
[base-files] shell-scripting: fix wrong usage of '==' operator
normally the '==' is used for invoking a regex parser and is a bashism.
all of the fixes just want to compare a string. the used busybox-ash
will silently "ignore" this mistake, but make it portable/clean at least.
this patch does not change the behavior/logic of the scripts.
Signed-off-by: Bastian Bittorf <bittorf@bluebottle.com>
SVN-Revision: 42911
Patch allows to configure the mtu of the dynamic 6rd tunnel interface when created by dhcp script.
In some setups it's desirable to have config control over the 6rd tunnel mtu to maximize the traffic throughput
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
SVN-Revision: 42871
This is not needed after all:
Omitting option ipv6 or setting it to 'auto' will
fire up a dhcpv6 subprotocol (this was added).
Setting ipv6 to 1 will only cause the IPv6 link to
be brought up and an accompanying dhcpv6 or static
interface with ifname @wan can be used to configure addresses.
Signed-off-by: Steven Barth <steven@midlink.org>
SVN-Revision: 42859
Use network_get_ipaddrs_all to get all ip-addresses of an interface. If the
function fails, the interface does not exists or has not any suiteable ip
addresses assigned.
Use the returned ip-address(es) to construct the dropbear listen address.
Signed-off-by: Mathias Kresin <openwrt@kresin.me>
SVN-Revision: 42857
This allows IPv6 to set up without IPv4 being up thus
IPv6-only or IPv6+DS-Lite working with the default config.
Signed-off-by: Steven Barth <steven@midlink.org>
SVN-Revision: 42848
it is now possible to inlie the uid and gid in the syntax
USERID:=username=uid:group=gid:group2=gid2:...
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 42838
this proto handler will detect which of 3g, qmi, mbim, ncm or directip you need
for a stick and setup uci automagically
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 42837
Some ISP seem to only do stateful DHCPv6 and not sending RAs.
This is technically broken because plain DHCPv6 doesn't carry routes.
We work around here by faking a default route to the DHCPv6 server
if we do not receive a useful RA from the ISP.
This workaround can be turned off with: option fakeroutes 0
Signed-off-by: Steven Barth <steven@midlink.org>
SVN-Revision: 42803
The AR9580 with the new ID can be found in the EnGenius ESR900 and the
QCA9880 without any subsystem IDs can be found in the EnGenius ESR1750.
Signed-off-by: Forest Crossman <cyrozap@gmail.com>
SVN-Revision: 42793
In r41872 Dynamic VLAN support was reintroduced, but the vlan_naming
parameter is not read while setting up the config, so it always
defaults to 1.
Signed-off-by: Reiner Herrmann <reiner@reiner-h.de>
SVN-Revision: 42787
During boot, a not found message is displayed for systems which do
not have uci 'network.globals.ula_prefix' defined in
/etc/config/network. The error message itself is not used and can
be ignored.
Signed-off-by: Michel Stam <m.stam@fugro.nl>
SVN-Revision: 42755
A message:
uinteger - 9 = true
is displayed during boot. This is the result of the validate_data
command checking the cron log level. As the output is not
interesting, only the result, filter...
Signed-off-by: Michel Stam <m.stam@fugro.nl>
SVN-Revision: 42751
Send a netlink call to leave the mesh when meshd exits
Make hunting-and-pecking loop (more) resistant to side channel attack
Signed-off-by: Michel Stam <m.stam@fugro.nl>
SVN-Revision: 42750
Tos support is added as a string parameter which can have the following values :
-inherit (outer header inherits the tos value of the inner header)
-hex value
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
SVN-Revision: 42749
Tos support is added as a string parameter which can have the following values :
-inherit (outer header inherits the tos value of the inner header)
-hex value
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
SVN-Revision: 42748
Tos support is added as a string parameter which can have the following values :
-inherit (outer header inherits the tos value of the inner header)
-hex value
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
SVN-Revision: 42747
The package supports IP in IP by registering the ipip protocol handler
Following options are configurable
-peeraddr (IPv4 remote address)
-ipaddr (IPv4 local address)
-ttl (time to live of encapsulating packet)
-tos (type of service of encapsulating packet either inherit (outer header inherits the value of the inner header) or hex value)
-df (don't fragment flag of encapsulating packet)
-mtu (IPIP tunnel mtu)
-tunlink (bind tunnel to this interface)
-zone (firewall zone to which the IPIP tunnel will be added)
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
SVN-Revision: 42746
When 'wifi down' is called by /etc/init.d/network, it is run from
stop_service( ). This function is in turn invoked from stop( ).
stop( ) messes up the order by first procd_kill-ing the network
settings, then calling wifi to down the wifi networking
interfaces. By redefining stop( ) instead, the proper order is
restored.
Signed-off-by: Michel Stam <m.stam@fugro.nl>
SVN-Revision: 42745
Instead of connecting once and saving the packet data handle, let the
firmware handle connecting/reconnecting automatically. This is more
reliable and reduces reliance on potentially stale data.
Use the global packet data handle to attempt to disable autoconnect
before restarting the connection. This ensures that the firmware will
take the new APN/auth settings.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 42721
Tos support is added as a generic grev4/grev6 parameter which can have the following values :
-inherit (outer header inherits the tos value of the inner header)
-hex value
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
SVN-Revision: 42700
Add a third argument to ucidef_set_interface_raw, which is specifying
the protocol.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 42665
Implementing "add-cert.sh" functionality described at
http://wiki.openwrt.org/doc/howto/wget-ssl-certs into Makefile
otherwise you need to create symbolic links for certificate hashes
yourself.
Signed-off-by: Christian Schoenebeck <christian.schoenebeck@gmail.com>
SVN-Revision: 42660
Without running fixtrx the image will not boot at the second time,
because the CRC the boot loader check is invalid at that time.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 42639
The ad799x driver moved out of staging since kernel 3.16, so update filepath,
config elements and description.
Signed-off-by: Hartmut Knaack <knaack.h@gmx.de>
SVN-Revision: 42524
It uses mtd, so doesn't require any special adjustments for new target.
It has been succesfully tested (reading, writing and commiting).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 42521
Main changes:
- URL parser: IPv6 zone identifiers are now supported
- cyassl: Use error-ssl.h when available (drop local patch)
- polarssl: support CURLOPT_CAPATH / --capath
- mkhelp: generate code for --disable-manual as well (drop local patch)
Full release notes: http://curl.haxx.se/changes.html
MIPS 34kc binary size:
- 7.36.0 before: 82,539 bytes
- 7.38.0 after: 83,321 bytes
Signed-off-by: Catalin Patulea <cat@vv.carleton.ca>
SVN-Revision: 42517
the postinst script enables/starts the init.d scripts upon package installation
and installs the users required by the package.
the prerm script stops and disables the init.d scripts.
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 42470
when running the postinst trigger we set PKG_UPGRADE=1 if this is an upgrade
and not an install.
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 42468
With this patch WPS discovery can be started or canceled over ubus if
WPS is enabled in wireless configuration. This is equivalent of
'hostapd_cli wps_pbc' and 'hostapd_cli wps_cancel' commands.
Signed-off-by: Petar Koretic <petar.koretic@sartura.hr>
SVN-Revision: 42459
The DFS pattern detector now supports all three regions; ETSI, FCC and
JP, so there is no reason to not have it enabled anymore.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 42431
The at91 OHCI driver has a separate Kconfig symbol with newer kernels,
include it.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 42411
On brcm47xx (Huawei E970), I noticed that sysupgrade now tries to flash trx images which don't fit into the flash, resulting in non-booting system.
I found that mtd does trx size checking only when flashing to a partition called "linux". This patch changes this to be "firmware".
This matches the following patch which changed partition name in bcm47xxpart.c driver to "firmware":
commit 86b4d5ef68ca77ff6724ebb9bddd6b93239c87fc
Author: hauke <hauke@3c298f89-4303-0410-b956-a3cf2f4a3e73>
Date: Sun Dec 1 16:32:32 2013 +0000
brcm47xx: use "firmware" partition name
...
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 38973
Signed-off-by: Mathias Adam <m.adam--openwrt@adamis.de>
SVN-Revision: 42403
Build libbfd and libopcodes as shared libraries, else they get linked
statically into every binary, increasing each binary size by ~650kB.
Reduces binutils package size to old expected values.
Fixes#17060.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 42337
* ipv6
* 4 bugs in the dns parser
* service announcement
* tx goodbye support
* proper handling of rx goodbye
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 42325
Use an if/else statement to cover the two different syntaxes. Add
comments explaining what the end results should look like.
This patch should not change the script's output.
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
SVN-Revision: 42320
An entry like this in /etc/config/dhcp:
config 'host'
option 'name' 'pc2'
option 'ip' '192.168.100.56'
option 'dns' '1'
results in a /tmp/hosts/dhcp entry that looks like this:
192.168.100.56 .lan
Obviously it should say "pc2.lan".
This happens because $name is set to "" in order to support the MAC-less
syntax: "--dhcp-host=lap,192.168.0.199". Fix this by reordering the
operations. Also, refuse to add a DNS entry if the hostname or IP is
missing.
Fixes#17683
Reported-by: Kostas Papadopoulos <kpapad75@travelguide.gr>
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
SVN-Revision: 42319
LuCI creates "domain" UCI config sections, which the dnsmasq init file
then, currently, translates into "address" config lines. This is not
the correct usage of "address" (see r36943), and also causes rDNS
records to not be created. This patches dnsmasq.init to utilize the
additional hosts file introduced in r40799 for such domain names,
resolving both issues.
Signed-off-by: Tyler Fenby <tylerf@securecominc.com>
SVN-Revision: 42318
A quite frequent problem after sysupgrading from an older, SSL enabled build
is that ustream-ssl is not installed so uhttpd fails to come up again due to
https listening directives in the preserved configuration.
Skip key/cert and ssl listen options when libustream-ssl.so is not present.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 42284
somebody started to set a function returncode in the validation
stuff and everybody copies it, e.g.
myfunction()
{
fire_command
return $?
}
a function automatically returns with the last returncode,
so we can safely remove the command 'return $?'. reference:
http://tldp.org/LDP/abs/html/exit-status.html
"The last command executed in the function or script determines the exit status."
Signed-off-by: Bastian Bittorf <bittorf@bluebottle.com>
SVN-Revision: 42278
Disable MIPS16 to prevent it negatively affecting performance.
Observed was a increase of connection delay from ~6 to ~11 seconds
and a reduction of scp speed from 1.1MB/s to 710kB/s on brcm63xx.
Fixes#15209.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 42250
Add a further upstream commit to more closely match the keepalive
to OpenSSH.
Should now really fix#17523.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 42249
Currently, any package that uses host compile and depends on
libgmp.so will fail. This is because gmp is not compile for
host machine. So, staging_dir/host has only static lib for gmp
$ ls staging_dir/host/lib/libgmp* -1
staging_dir/host/lib/libgmp.a
staging_dir/host/lib/libgmp.la
staging_dir/host/lib/libgmpxx.a
staging_dir/host/lib/libgmpxx.la
Addind host compile in gmp, the dependent package can use:
PKG_BUILD_DEPENDS:=gmp/host
That will compile gmp to staging_dir/host with *.so files
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
SVN-Revision: 42196
Patch to BusyBox Makefile to fix linker errors when PAM support is enabled by
CONFIG_BUSYBOX_CONFIG_PAM=y. Typical errors include:
login.c:(.text.login_main+0x122): undefined reference to `pam_start'
Signed-off-by: Stephen Parry <sgparry@mainscreen.com>
SVN-Revision: 42195
this allows targets to use the new uci-default helper which will generate
a file called /etc/board.json. a tool called /bin/config_generate can then
be used to generate the default uci settings.
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 42185
Don't send SSH_MSG_UNIMPLEMENTED for keepalive responses, which broke
at least putty.
Fixes#17522 / #17523.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 42162
This is a bug revealed in r41830.
First, the static variable `char nif[IFNAMSIZ]` of nl80211_phy2ifname()
would be zeroed out if the argument is "wlan0" or the like. This will
happen in the following call stack.
nl80211_get_scanlist("radio0", buf, len);
nl80211_phy2ifname("radio0") // return static var nif with content "wlan0"
nl80211_get_scanlist(nif, buf, len); // tail call
nl80211_get_mode(nif);
nl80211_phy2ifname(nif); // zero out nif
Later we try nl80211_ifadd("") which was supposed to create interface
"tmp.", but that won't happen because nl80211_msg() will put an invalid
ifidx 0 to the nlmsg.
Then iwinfo_ifup() and iwinfo_ifdown() would fail and happily
nl80211_get_scanlist() returned 0 and left *len undefined.
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
SVN-Revision: 42151
The GW16083 Ethernet Expansion Mezzanine adds the following to supported
Gateworks baseboards:
* 7-port Ethernet Switch
* 4x RJ45 ports (ENET1-4) supporing 802.11af/at PoE (with optional PoE module)
* 2x RJ45 ports or SFP module (ENET5-6) (auto-selected)
This series adds support for a phy driver that adds support for ENET5/ENET6
PHY adding initialization for those PHY's and a polling mechanism that detects
SFP insertion and configuration.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
SVN-Revision: 42147
When looking for the first ipaddr also consider the current prefix just
like network_get_ipaddrs6 does. If ipv6-address was empty the function
did not return the first ipaddr even if the list was non-empty.
fixes commit 83e9122f88a002871d5cdf421cf6aa6052b7e006
Signed-off-by: Henning Schild <henning@hennsch.de>
SVN-Revision: 42139
Utilize the new selective conntrack flushing facility to clear
out active conntrack entries referring to old IP addresses after
a firewall reload.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 42114
Enable the separate feed repositories by default to align custom builds with the repositories
available on the snapshot download server.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 42112
This adds default tx and rx antennas, so that LuCI shows automatic as the default radio option for the antennas.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 42085
NFLOG and NFQUEUE targets' full support for iptables.
Includes all needed kernel modules (Xtables's and Netlink's)
and userspace libraries.
All added kernel modules can be individually disabled,
all other new libraries get their own individual packages.
Reported-by: Fabian Hugelshofer <hugelshofer2006@gmx.ch>
Reported-by: Rainer Poisel <rainer.poisel@fhstp.ac.at>
Reported-by: Derek LaHousse <dlahouss@mtu.edu>
Signed-off-by: Guillaume Déflache <guillaume.deflache@ibwag.com>
SVN-Revision: 42022
This changeset implements a new menuconfig option to generate separate
repositories for each enabled package feed instead of one monolithic one.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 42002
This commit implements a new netfilter match "xt_id" which can be used to
attach unsigned 32bit IDs to iptables rules.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 41945
Fixes
b43-phy0 ERROR: Firmware file "b43-open/ucode30_mimo.fw" not found
for BCM43217 devices.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 41943
configure enables libzfs support on default.
This will break the build, on systems without libzfs.
Signed-off-by: Hans Ulli Kroll <ulli.kroll@googlemail.com>
SVN-Revision: 41935
* set the system time/data
* "ubus call gps info" will tell you lattitude, longitude, elevation, speed and bearing
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 41929
This add 5GHz support for N-PHY to b43, thanks Rafał Miłecki.
b43_wflush16 was put into an extra function because it is pretty big in asm.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 41900
The package supports Generic Routing Encapsulation support by registering following protocol kinds:
-gre
-gretap
-grev6
-grev6tap
Following options are valid for gre and gretap kinds:
-ipaddr
-peeraddr
-df
-mtu
-ttl
-tunlink
-zone
-ikey
-okey
-icsum
-ocsum
-iseqno
-oseqno
The gretap kind supports additionally the network option
Following options are valid for grev6 and grev6tap kinds:
-ip6addr
-peer6addr
-weakif
-mtu
-ttl
-tunlink
-zone
-ikey
-okey
-icsum
-ocsum
-iseqno
-oseqno
The grev6tap kind supports additionally the network option
Typical network config for a GREv4 tunnel :
config interface 'gre'
option peeraddr '172.16.18.240'
option mtu '1400'
option proto 'gre'
option tunlink 'wan'
option zone 'tunnel'
Typical network config for a GREv4 tap tunnel :
config interface 'gretap'
option peeraddr '195.207.5.79'
option mtu '1400'
option proto 'gretap'
option zone 'tunnel'
option tunlink 'wan'
option network 'wlan_ap'
I added myself as maintainer for the moment; feel free to change.
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
SVN-Revision: 41897
Make sure they don't break the sed command, and also make device_info
and openwrt_release more robust for parsing by scripts
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 41885
Creates /etc/device_info which will be used to fill in information for
WPS and other protocols that need manufacturer/device information
This helps with creating OpenWrt firmware for OEM or rebranded devices.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 41884
This change introduces support for wildcard patterns in "option path"
of section "wifi-device".
Objective is to allow paths like "*/usb[0-9]/*/*" in order to claim
any usb device using the same backend type, regardless of its bus
address or phy name.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 41873
This patch brings full dynamic vlan support to netifd that existed in hostapd.sh in Attitude Adjustment.
Signed-off-by: Joseph CG Walker <Joe@ChubbyPenguin.net>
[jow@openwrt.org: changed commit message, rebased on top of current hostapd.sh]
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 41872
If the iface to scan on already is in ad-hoc, station or monitor mode
then do not spawn a temporary iface.
Also preventively disable IPv6 on temporary ifaces before bringing them
up to avoid potential security issues.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 41830
So far iwinfo aborted a wifi scan attempt if the mac of the spawned
interface could not be changed. Change the code to try anyway - this
should fix wifi scanning on RaLink devices.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 41826
the IB tries to run the enable target on all init.d scripts.
It fails when including the dsl_control helper. Check for existence
prior to the include.
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 41787
Properly parse and pass arbritary netmasks to iptables, this allows
specifying ranges like '::c23f:eff:fe7a:a094/::ffff:ffff:ffff:ffff' to
match the host part of an IPv6 address regardless of the currently active
IPv6 prefix.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 41760
Split connection mark into two parts:
The lower nibble contains the confirmed conntrack mark which is not
generated by default/reclassify rules.
The upper nibble contains the current value specified by
default/reclassify rules.
For egress, the default/reclassify value is preferred
For ingress, the connection mark is preferred
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 41682
With this patch mac80211 will be rebuild when one of these config
options was changed.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 41677
I missed adding B43_PHY_G to .local-symbols, without this it will not
be added to autoconf.h
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 41676
Generate the configuration file for uboot-envtools
on BTHOMEHUBV2B. Adds the specific parameters for the
BTHOMEHUBV2B and also fixes an incorrect path which
would have affected other lantiq boards as well
(currently only the GIGASX76X).
Signed-off-by: Ben Mulvihill <ben.mulvihill@gmail.com>
SVN-Revision: 41597
A missing path prevents the rootfs type contained in a SysupgradeNAND
tar file from being determined correctly.
This fixes it, and also corrects a minor spelling mistake.
Signed-off-by: Ben Mulvihill <ben.mulvihill@gmail.com>
SVN-Revision: 41564
If the sysupgrade scripts is called under upgraded, it will not kill all
other processes as it should to avoid interference by locked filesystem.
This patch checks the parent and if it is upgraded, it kills all.
Signed-off-by: André Valentin <avalentin@marcant.net>
SVN-Revision: 41563
The vif option dtim_period was accidently renamed dtim_interval in r38988
("netifd: add wireless configuration support and port mac80211 to the new
framework"). This is wrong and makes the dtim_period/dtim_interval a dead
option because the rest of the config generation code still uses dtim_period.
Reported-by: Jeppe Ledet-Pedersen <jlp@steinwurf.com>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
SVN-Revision: 41557
The commit 92281eb747b56e748b7c3d754055919c23befdd4 broke fw3_ubus_addresses() so that
no addresses where returned at all, this caused fw3 to not emit NAT reflection rules
anymore.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 41556
They should be unnecessary with fq_codel, and simplifying rules helps
with performance
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 41549
When the original mac addresses are not valid assign the first one to
the internal wifi core, this matches the manufacture mac address in
most cases. In addition refresh the patches.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 41545
This updates linux-firmware to version
7f388b4885cf64d6b7833612052d20d4197af96f from 2014-06-04.
In addition it adds new firmware for Intel, Broadcom and Realtek devices.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 41523
Some devices have an nvram setting, which make broadcom-wl turn of the
led all the time. When the driver is switched on and we find such a
setting we replace it with a better value.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 41518
Some series of devices are using the same mac address, which causes
conflicts for these devices we generate a new mac address based on the
base address. This patch adds this functionality to braodcom-wl.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 41514
in r41439 a flag for enabling remote logging was added,
but the actual check was done on a different variable.
Signed-off-by: Reiner Herrmann <reiner@reiner-h.de>
SVN-Revision: 41467
currently the keepalive option needs to be removed to fully disable it. this patch allows us to set it to 0.
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 41438
Regardles of the return code from validate_data _error variable will be 0 due
to 'local' command in the previous line. With this patch we are able to catch
the return code from validate_data tool.
Signed-off-by: Luka Perkov <luka@openwrt.org>
SVN-Revision: 41414
ubox validate_data defines yes/no as valid boolean options, do the same in
config_get_bool too.
Signed-off-by: Luka Perkov <luka@openwrt.org>
SVN-Revision: 41405
The preferred he.net /nic/update endpoint expects the password or updatekey in
plain text and not as md5 sum, therfore remove the hashing operation from the
script.
This effectively renders the "updatekey" option redundant but we keep it around
for backwards compatibility. Both "option password" and "option updatekey" will
have end up in the "&password=" parameter of the update url and are passed through
unmodified.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 41358
The current $(wildcard ...) match might return multiple files which will break subsequent cp commands
with an error like:
cp: target `/home/user/openwrt/staging_dir/target-mips_34kc_uClibc-0.9.33.2/root-ar71xx/tmp-libc/lib/libgcc_s_pic.a' is not a directory
Prevent this issue by only taking the last path returned by globbing.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 41357
Even if enabled option is missing from ntp configuration we are still keeping
default behavior.
Signed-off-by: Luka Perkov <luka@openwrt.org>
SVN-Revision: 41355
this is still wip, you can use the following ubus calls.
ubus call mdns scan # triggers a scan
ubus call mdns browse # look at the currenlty cached records
ubus call mdns hosts # look at the currenlty cached hosts
TODO
- ipv6, currenlty AAAA records are handled but only on v4 sockets
- finish the service announce code
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 41345
sysupgrade otherwise skips kernel part on devices which got
kernel in ubi due to kern_length being undefined, kernel_length
is being used instead.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 41327
Insert a missing #ifdef UBI around the use of libubi_close().
As the preceding if (libubi) will never be true on non-UBI builds,
compiling only failed when disabling optimization.
Also rebase patch to latest u-boot.git HEAD.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 41313
Reworks the handling of RT_TABLE_MAIN in system-linux.c so that ip rules
with lookup main can be properly setup.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 41282
Switches /lib/functions/network.sh from jshn based json parsing to
jsonfilter expression while keeping the existing api.
Expensive methods like "network_find_wan" are up to 20x faster now.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 41281
The CLI now describes expression errors more precisely, e.g.:
Syntax error: Invalid escape sequence
In expression @["foo\x"]
Near here ----------^
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 41266
This commit renames the jsonpath binary to jsonfilter to avoid clashing with a Python
extension of the same name.
The utility itself has been rewritten to use SQLite3's lemon parser generator instead
of a flex/bison combination which results in a much smaller binary.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 41258
* Add Authoritative DNS and IPSET to full variant
* Remove some bloat from IPSET support
* Reintroduce "DHCP no address warning"-patch
Signed-off-by: Steven Barth <steven@midlink.org>
SVN-Revision: 41246
Ship keys for the root zone and add two uci options to enable
DNSSEC checks:
Option 'dnssec': Activate DNSSEC validation
Option 'dnsseccheckunsigned': Ensure answers without DNSSEC are in
unsigned zones.
Signed-off-by: Andre Heider <a.heider@gmail.com>
SVN-Revision: 41245
This variant includes support for DHCPv6 and DNSSEC.
DNSSEC adds a dependency on libnettle.
Signed-off-by: Andre Heider <a.heider@gmail.com>
SVN-Revision: 41244
As documented in config.h.
Doing otherwise will break dnsmasq's pkg-wrapper script to find its
libs to link to.
Signed-off-by: Andre Heider <a.heider@gmail.com>
SVN-Revision: 41241
Removed unused ubi file file from template as ubinized images are
passed directly and not inside the tarball.
Also removed left-over white-space.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 41237
i got complaints about the bad naming of the api. lets rename it while there are no users yet.
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 41220
r40682 ("mac80211: clean up ht capability handling, drop the use of the
ht_capab list, use individual variables instead") removed the ht_capab list and
replaced it with optional variables to disable features for a phy. But these
variables weren't added in drv_mac80211_init_device_config and thus didn't make
any difference when modifying /etc/config/wireless.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
SVN-Revision: 41180
Also add some more busybox symlinks which are useful for sysupgrade
on UBI-enabled devices.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 41125
Instead of repackaging udc-core.ko again, just add a dependency to
kmod-usb-gadget, which already contains it.
Fixes kmod-chipidea builds for 3.10- with usb-gadget enabled.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 41115
broadcom-diag is not supported any more and was replaced by
configuration the GPIOs in the arch code
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 41047
Seems like the reverse order relies on GNU specific getopt hackery which
musl does not replicate
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 41045
Without this patch, /etc/hotplug.d/tty/30-3g won't be called when you insert or remove a USB-serial cellular modem.
(see Ticket #14117)
Signed-off-by: Matthew Reeve <mreeve@tenxnetworks.com>
SVN-Revision: 41039
ubiblock allows creating and removing read-only block devices
on top of ubi volumes.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 41033
today appeared another serious vulnerability in openssl. More info is
here http://ccsinjection.lepidum.co.jp. Users are advised to update to
openssl 1.0.1h.
Signed-off-by: Martin Strbacka <martin.strbacka@nic.cz>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 41026
Fixed wpa_supplicant when the radio is in 40MHz mode so that it no
longer restarts hostapd with the second channel disabled.
Signed-off-by: Lance Chaney <furryfur1@gmail.com>
SVN-Revision: 41019
