The Actiontec R1000H is a gigabit wifi router, 2.4 GHz single band with
two external antennas. It comes with a coaxial HomePNA port.
Hardware:
- SoC: Broadcom BCM6368
- CPU: dual core BMIPS4350 V3.1 @400Mhz
- RAM: 64 MB DDR
- Flash: 32 MB parallel NOR
- LAN switch: Broadcom BCM53115, 5x 1Gbit
- LAN coaxial : 1x HPNA 3.1, CG3211 + CG3213
- Wifi 2.4 GHz: Broadcom BCM4322 802.11bgn
- USB: 1x 2.0
- Buttons: 2x, 1 reset
- LEDs: 7x
- UART: yes
The HPNA hardware probably needs a firmware to make the coaxial port work.
In the OEM firmware, it's apparently sent with an utility (inhpna) through
the ethernet port.
Installation via CFE web UI:
1. Connect the UART serial port.
2. Power on the router and press enter at the console prompt to stop the
bootloader.
4. Browse to http://192.168.1.1 and upload the OpenWrt CFE firmware
5. Wait a few minutes for it to finish
Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
The Comtrend WAP-5813n is a wifi gigabit router, 2.4 GHz single band with
two external antennas.
Hardware:
- SoC: Broadcom BCM6369
- CPU: dual core BMIPS4350 @ 400Mhz
- RAM: 64 MB DDR
- Flash: 8 MB parallel NOR
- LAN switch: Broadcom BCM53115, 5x 1Gbit
- Wifi 2.4 GHz: miniPCI Broadcom BCM4322 802.11bgn
- USB: 1x 2.0 (optional)
- Buttons: 3x (reset)
- LEDs: yes
- UART: yes
Installation via CFE web UI:
1. Power off the router.
2. Press reset button near the power switch.
3. Keep it pressed while powering up during ~20+ seconds.
4. Browse to http://192.168.1.1 and upload the firmware.
5. Wait a few minutes for it to finish.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
The Comtrend VR-3025un is a wifi gigabit router, 2.4 GHz single band with
two external antennas.
Hardware:
- SoC: Broadcom BCM6368
- CPU: dual core BMIPS4350 @ 400Mhz
- RAM: 64 MB DDR
- Flash: 8 MB parallel NOR
- Ethernet LAN: 4x 100Mbit
- Wifi 2.4 GHz: miniPCI Broadcom BCM43222 802.11bgn
- USB: 1x 2.0
- Buttons: 1x (reset)
- LEDs: yes
- UART: yes
Installation via CFE web UI:
1. Power off the router.
2. Press reset button near the antenna.
3. Keep it pressed while powering up during ~20+ seconds.
4. Browse to http://192.168.1.1 and upload the firmware.
5. Wait a few minutes for it to finish.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
The Netgear EVG2000 is a wifi gigabit router, 2.4 GHz single band with
two internal antennas integrated in the main PCB.
Hardware:
- SoC: Broadcom BCM6369
- CPU: dual core BMIPS4350 V3.1 @400Mhz
- RAM: 64 MB DDR
- Flash: 16 MB parallel NOR
- LAN switch: Broadcom BCM53115, 5x 1Gbit
- Wifi 2.4 GHz: Broadcom BCM4322 802.11bgn
- USB: 2x 2.0
- Buttons: 2x, 1 reset
- LEDs: 10x
- FXS: 2x
- UART: yes
Installation via CFE web UI:
1. Power off the router and make a temporal TX-RX shortcircuit on the
serial pins.
2. Power on the router and wait 3 or more seconds
3. Remove the TX-RX shortcircuit
4. Browse to http://192.168.1.1 or http://192.168.0.1 and upload the
firmware
5. Wait a few minutes for it to finish
Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
The Netgear DGND3700 v1 and DGND3800B are the same device but with
different factory firmwares. It's an xDSL wifi router with a slim black
shiny casing and 4 PCB internal antennas connected via UFL to a miniPCI
detachable card.
Hardware:
- SoC: Broadcom BCM6368
- CPU: dual core BMIPS4350 V3.1 @400Mhz
- RAM: 128 MB DDR
- NOR Flash: 32 MB parallel (CFE and OS)
- NAND flash: 128 MB (empty)
- Ethernet LAN: 5x 1Gbit
- Wifi 2.4 GHz: Broadcom BCM43222 802.11bgn
- Wifi 5 GHz: Broadcom BCM43222 802.11abgn
- USB: 2x 2.0
- Buttons: 3x, 1 reset
- LEDs: 11x
- UART: yes
Installation via OEM web UI:
1. Open the Netgear administration web interface, by default:
http://192.168.0.1
user: admin
password: password
2. Look for "upgrade firmware" and proceed
3. Wait some minutes until it finishes
Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
The Observa VH4032N is an xDSL wifi router with a vertical white casing
and two internal antennas connected via UFL.
Hardware:
- SoC: Broadcom BCM6368
- CPU: dual core BMIPS4350 V3.1 @400MHz
- RAM: 128 MB DDR
- Flash: 32 MB parallel NOR
- Ethernet LAN: 4x 100Mbit
- Wifi 2.4/5 GHz: onboard Broadcom BCM43222 802.11abgn
- USB: 3x 2.0
- Buttons: 2x, 1 reset
- LEDs: 8x, blue and red
- UART: 1x
Installation via OEM web UI:
1. Use the admin credentials to login via web UI
2. Go to Managament->Update firmware and select the OpenWrt CFE firmware
3. Press "Update Firmware" button and wait some minutes until it finish
Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
BMIPS is a generic arch that can be used for multiple Broadcom SoCs, each one
with its own specific drivers, so instead of having a huge kernel supporting
all of them, let's switch to a subtarget per SoC like other OpenWrt targets.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
