Based on the discussion on the mailing list [1], the patch which was
reverted, it reverts only one patch without the subsequent ones.
This leads to the SoC scaling issue not using a CPU parent clock, but
it uses DDR clock. This is done for all variants, and it's wrong because
commits (hacks) that were using the DDR clock are no longer in the mainline kernel.
If someone has stability issues on 1.2 GHz, it should not affect all
routers (1 GHz, 800 MHz) and it should be rather consulted with guys, who are trying to
improve the situation in the kernel and not making the situation worse.
There are two solutions in cases of instability:
a) disable cpufreq
b) underclock it up to 1 GHz
This reverts commit 080a0b74e3.
[1] https://lists.openwrt.org/pipermail/openwrt-devel/2021-June/035702.html
CC: Pali Rohár <pali@kernel.org>
Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
(cherry picked from commit 7b868fe04a)
Kernel 5.10 is not supported by OpenWrt 21.02, remove this patch.
Fixes: d530ff37bf ("mvebu: armada 370: dts: fix the crypto engine")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Removed because in upstream*
mvebu/patches-5.4/319-ARM-dts-turris-omnia-configure-LED-2--INTn-pin-as-interrupt-pin.patch
Manually rebased*
generic/backport-5.4/700-v5.5-net-core-allow-fast-GRO-for-skbs-with-Ethernet-heade.patch
Added new backport*
generic/backport-5.4/050-gro-fix-napi_gro_frags-Fast-GRO-breakage-due-to-IP-a.patch
All others updated automatically.
The new backport was included based on this[1] upstream commit that will be
mainlined soon. This change is needed because Eric Dumazet's check for
NET_IP_ALIGN (landed in 5.4.114) causes huge slowdowns on drivers which use
napi_gro_frags().
Compile-tested on: x86/64, armvirt/64, ath79/generic
Runtime-tested on: x86/64, armvirt/64, ath79/generic
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The crypto engine in Armada 370 SoCs is currently broken. It can be
checked installing the required packages for testing openssl with hw
acceleration:
opkg install openssl-util
opkg install kmod-cryptodev
opkg install libopenssl-devcrypto
After configuring /etc/ssl/openssl.cnf to let openssl use the crypto
engine for digest operations, and performing some checksums..
md5sum 10M-file.bin
openssl md5 10M-file.bin
...we can see they don't match.
There might be an alignment or size constraint issue caused by the
idle-sram area.
Use the whole crypto sram and disable the idle-sram area to fix it. Also
disable the idle support by adding the broken-idle property to prevent
accessing the disabled idle-sram.
We don't care about disabling the idle support since it is already broken
in Armada 370 causing a huge performance loss because it disables
permanently the L2 cache. This was reported in the Openwrt forum and
elsewhere by Debian users with different board models.
Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
(cherry picked from commit 2e1ebe96c6)
The GL.iNet GL-MV1000 is booting from eMMC and the images for it are in
theory sysupgrade compatible. But the platform upgrade scripts were not
adjusted to select the mmcblock device as upgrade target. This resulted in
a failed sysupgrade because the mtd device (NOR flash) was instead tried to
be modified by the sysupgrade script.
Fixes: 050c24f05c ("mvebu: add support for GL.iNet GL-MV1000")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
(cherry picked from commit 07e5e03711)
Move some disabled symbols found in armvirt target to generic.
Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
(cherry picked from commit 12e942b1fd)
1. Use upstream accepted NVMEM patches
2. Minor fix for BCM4908 partitioning
3. Support for Linksys firmware partitions on Northstar
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit 3fd0a4222b)
The original GL.iNet firmware has two different mac addresses in the
factory/art partition. The first one is for the WAN interface only and the
second one is for both lan0 and lan1.
But the original submission for OpenWrt didn't initialize the mac
addresses of the LAN ports for the DSA device at all. The ethernet mac
address was then used for all DSA ports.
Fixes: 050c24f05c ("mvebu: add support for GL.iNet GL-MV1000")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
(cherry picked from commit c20ac84803)
The original patch to support this device advertised support for the reset
button and the "switch" in the commit message. But neither were actually
integrated in the device tree or documented anywere.
The button itself is now used to trigger a reset (as described in the
official GL.iNet documentation). The switch itself is registered as BTN_0
like other devices from GL.iNet in ath79.
Fixes: 050c24f05c ("mvebu: add support for GL.iNet GL-MV1000")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
(cherry picked from commit 01b911a938)
Kernel size limits have been dealt with.
Effective revert of a1eb2c46 and ac9730c4.
Signed-off-by: Tad Davanzo <tad@spotco.us>
(cherry picked from commit b4f76d9f0d)
venom has a 3MB kernel partition as specified by the DTS.
3MB is not sufficient for building with many kernel modules or newer
kernel versions.
venom uboot however as set from factory will load up to 6MB.
This can be observed by looking a uboot log:
NAND read: device 0 offset 0x900000, size 0x600000
6291456 bytes read: OK
and from uboot environment variables:
$ fw_printenv | grep "priKernSize";
priKernSize=0x0600000
Resize the root partitions from 120MB to 117MB to let kernel expand
into it another 3MB.
And set kernel target size to 6MB.
Lastly set the kernel-size-migration compatibility version on venom to
prevent sysupgrading without first reinstalling from a factory image.
Signed-off-by: Tad Davanzo <tad@spotco.us>
(cherry picked from commit 15309f5133)
mamba has a 3MB kernel partition as specified by the DTS.
3MB is not sufficient for building with many kernel modules or newer
kernel versions.
mamba uboot however as set from factory will load up to 4MB.
This can be observed by looking a uboot log:
NAND read: device 0 offset 0xa00000, size 0x400000
4194304 bytes read: OK
and from uboot environment variables:
$ fw_printenv | grep "pri_kern_size";
pri_kern_size=0x400000
Resize the root partitions from 37MB to 36MB to let kernel expand
into it another 1MB.
And set kernel target size to 4MB.
Lastly add a compatibility version message: kernel-size-migration.
And set it on mamba to prevent sysupgrading without first reinstalling from
a factory image.
Signed-off-by: Tad Davanzo <tad@spotco.us>
(cherry picked from commit 10415d5e70)
This patch enables LED support for the GL.iNet GL-MV1000
Signed-off-by: Jeff Collins <jeffcollins9292@gmail.com>
[add SPDX identifier on new file, add aliases, minor cosmetic issues]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit 6e0c780eb3)
It's meant to provide upstream support for mtd & NVMEM. It's required
e.g. for reading MAC address from mtd partition content. It seems to be
in a final shape so it's worth testing.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit e90e75b12c)
This adds the latest version of ofpart commit. It hopefully
1. Doesn't break compilation
2. Doesn't break partitioning
(this time).
It's required to implement fixed partitioning with some quirks. It's
required by bcm53xx, bcm4908, kirkwood, lantiq and mvebu.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit 7a7b2fd809)
There are proper workarounds merged to 5.4 stable tree for ESPRESSObin
boards with older bootloader:
4e1a23779bde ("ata: ahci: mvebu: Make SATA PHY optional for Armada 3720")
40af962eb1d4 ("usb: host: xhci: mvebu: make USB 3.0 PHY optional for
Armada 3720")
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
All modification made by update_kernel.sh in a fresh clone without
existing toolchains.
Build-tested: bcm27xx/bcm2711, ipq806x/R7800,
Run-tested: ipq806x/R7800
No dmesg regressions, everything functional
Signed-off-by: John Audia <graysky@archlinux.us>
Currently it's not possible to boot the device with just initramfs image
without additional effort as the initramfs image doesn't contain device
tree. Fix it by producing FIT based image which could be booted with
following commands:
setenv bootargs earlyprintk console=ttyS0,115200
tftpboot ${kernel_addr_r} openwrt-mvebu-cortexa9-cznic_turris-omnia-initramfs-kernel.bin
bootm ${kernel_addr_r}
Acked-by: Klaus Kudielka <klaus.kudielka@gmail.com>
Reviewed-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
The thermal zones kernel documentation is misleading, we cannot use more
than one sensor in a thermal zone node.
Furthermore the drivetemp driver for some reason it only catches one
sensor from the hard drives array (the first available).
In the Buffalo Linkstation LS421DE board there is also a sensor at the
ethernet phy chip that can also be monitored. Very useful to stop the fan
when there are no hard drives in the bays.
(It might be also possible to add the CPU sensor, but it requires kernel
patching for registering the sensor via device tree, using the function:
devm_thermal_zone_of_sensor_register)
Fix the thermal zones to use only one sensor per node and add the ethernet
phy sensor. Also adjust the hdd temperatures to be more conservative for
a mechanical hard drive.
Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
The majority of our targets provide a default value for the variable
SUPPORTED_DEVICES, which is used in images to check against the
compatible on a running device:
SUPPORTED_DEVICES := $(subst _,$(comma),$(1))
At the moment, this is implemented in the Device/Default block of
the individual targets or even subtargets. However, since we
standardized device names and compatible in the recent past, almost
all targets are following the same scheme now:
device/image name: vendor_model
compatible: vendor,model
The equal redundant definitions are a symptom of this process.
Consequently, this patch moves the definition to image.mk making it
a global default. For the few targets not using the scheme above,
SUPPORTED_DEVICES will be defined to a different value in
Device/Default anyway, overwriting the default. In other words:
This change is supposed to be cosmetic.
This can be used as a global measure to get the current compatible
with: $(firstword $(SUPPORTED_DEVICES))
(Though this is not precisely an achievement of this commit.)
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The following four led triggers are enabled in generic config.
* kmod-ledtrig-default-on
* kmod-ledtrig-heartbeat
* kmod-ledtrig-netdev
* kmod-ledtrig-timer
Drop the packages and remove them from DEVICE_PACKAGES.
There's no other package depending on them in this repo.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Backport the upstream kernel fix 525b0858ff to get rid of the kernel
messages:
mvebu-gpio xxxxxx.gpio: IRQ index 3 not found
Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
The Buffalo Linkstation LS421DE comes with a Ricoh RS5C372A real time
clock. This RTC has the INTRA pin connected to the power management
circuit, allowing to wake up the device from the power off state when an
alarm is scheduled.
Add the "wakeup-source" property in the RTC dts node to allow the use
of the alarm.
Example of use, the device is powered off and it comes to life after 5
minutes:
echo $(expr $(date '+%s') + 60 * 5) > /sys/class/rtc/rtc0/wakealarm
poweroff
This feature isn't available in the stock firmware.
Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
The Buffalo Linkstation LS421DE isn't able to enable the Level 2 cache
(AKA Aurora cache). As of result of this, the throughput is about half of
the expected, e.g when doing network data transfers.
Fix it by adding the broken-idle property in the coherency fabric node.
Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
This adds DTB to kernel and that way makes it possible to easily boot
initramfs image and also kernel.
The sequence to boot initramfs on Omnia is then just:
env set bootargs earlyprintk console=ttyS0,115200
dhcp 0x1000000 192.168.1.1:openwrt-mvebu-cortexa9-cznic_turris-omnia-initramfs-kernel.bin
bootz 0x1000000
Without this change kernel boot won't proceed and is stuck on "Starting
kernel".
Signed-off-by: Karel Kočí <karel.koci@nic.cz>
[fixed From: to match with SoB:]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This will explain what is actually occuring on dd invocations.
Additionally remove comments for steps which are described by printed
statements anyway.
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Fixup dfa357a3de "mvebu: base-files: Update Turris Omnia U-Boot
environment" which should have included this file as well.
By rebasing the initial patch this file somehow disappeared.
Signed-off-by: Klaus Kudielka <klaus.kudielka@gmail.com>
Reviewed-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Tested-by: W. Michael Petullo <mike@flyn.org> (Turris Omnia "2020")
Tested-by: Klaus Kudielka <klaus.kudielka@gmail.com> (Turris Omnia)
[explain fixup in commit message]
Signed-off-by: Paul Spooren <mail@aparcar.org>
Move the update procedure from sysupgrade to first boot, which is much
more convenient in the sysupgrade case (otherwise the environment is
always one generation behind).
Check whether we have an old U-Boot release installed, and update the
environment only if necessary.
Some notes on the U-Boot environment:
The first 9 lines are a copy of the default environment of the old U-Boot
release - only modified, to run "distro_bootcmd", in case "mmcboot" fails
to boot the factory OS.
The remaining 16 lines are a backport of the default environment of the
new U-Boot release (shipped with CZ11NIC23). The main entry point is
"distro_bootcmd", which eventually sources boot.scr. This way, we have
a unified boot protocol for all Turris Omnia revisions so far.
This commit also fixes a shortcoming of previous Turris Omnia support:
Users may install OpenWrt with the Turris Omnia in factory state
(i.e. invalid environment store). In that case, neither fw_setenv, nor
U-Boot itself, would import the default environment from the image -
screwing up the rescue system, at least!
Signed-off-by: Klaus Kudielka <klaus.kudielka@gmail.com>
Reviewed-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Tested-by: W. Michael Petullo <mike@flyn.org> (Turris Omnia "2020")
Tested-by: Klaus Kudielka <klaus.kudielka@gmail.com> (Turris Omnia)
In contrast to the U-Boot version shipped with older versions of Turris
Omnia (CZ11NIC13, CZ11NIC20), the version shipped with Turris Omnia 2019
(CZ11NIC23) relies on the existence of /boot.scr.
Consequently, add a suitable boot script to the sysupgrade image.
Flash instructions for Turris Omnia 2019:
- Download openwrt-...-sysupgrade.img.gz, gunzip it, and copy the resulting
.img file to the root of a USB flash drive (FAT32 or ext2/3/4).
- Enter a rescue shell: Either via 5-LED reset and ssh root@192.168.1.1
on LAN port 4, or via 7-LED reset and the serial console.
- Insert the USB drive and mount it:
mkdir /mnt; mount /dev/sda1 /mnt
- Flash the OpenWrt image to eMMC:
dd if=/mnt/openwrt-...-sysupgrade.img of=/dev/mmcblk0 bs=4096 conv=fsync
- Reboot.
Flash instructions using a temporary "medkit" installation were written for
the older versions of Turris Omnia, and will *not* work on the Turris Omnia
2019.
Signed-off-by: Klaus Kudielka <klaus.kudielka@gmail.com>
Reviewed-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Tested-by: W. Michael Petullo <mike@flyn.org> (Turris Omnia "2020")
This is already done by get_partitions.
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
[add "redundant" to title, remove declaration of magic variable]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Sort patches according to target/linux/generic/PATCHES. Additionally:
- replace hashes in backported patches with the ones from main Linux tree
- add descriptions to some patches
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
[remove 004-add_sata_disk_activity_trigger.patch separately]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Remove 004-add_sata_disk_activity_trigger.patch, as the trigger is
already added in shared dtsi.
Suggested-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This patch adds support for Globalscale ESPRESSObin-Ultra. Device uses
the same Armada-3720 SoC with extended hardware support.
- SoC: Armada-3720
- RAM: 1 GB DDR4
- Flash: 4MB SPI NOR (mx25u3235f) + 8 GB eMMC
- Ethernet: Topaz 6341 88e6341 (4x GB LAN + 1x WAN with 30W PoE)
- WiFI: 2x2 802.11ac Wi-Fi marvell (88w8997 PCIe+USB)
- 1x USB 2.0 port
- 1x USB 3.0 port
- 1x microSD slot
- 1x mini-PCIe slot (USB [with nano-sim slot])
- 1x mini-USB debug UART
- 1x RTC Clock and battery
- 1x reset button
- 1x power button
- 4x LED (RGBY)
- Optional 1x M.2 2280 slot
** Installation **
Copy dtb from build_dir to bin/ and run tftpserver there:
$ cp ./build_dir/target-aarch64_cortex-a53_musl/linux-mvebu_cortexa53/
linux-5.4.65/arch/arm64/boot/dts/marvell/armada-3720-espressobin-ultra.dtb
bin/targets/mvebu/cortexa53/
$ in.tftpd -L -s bin/targets/mvebu/cortexa53/
Connect to the device UART via microUSB port on the back side and power on the device.
Power on the device and hit any key to stop the autoboot.
Set serverip (host IP) and ipaddr (any free IP address on the same subnet), e.g:
$ setenv serverip 192.168.1.10 # Host
$ setenv ipaddr 192.168.1.15 # Device
Ping server to confirm network is working:
$ ping $serverip
Using neta@30000 device
host 192.168.1.15 is alive
Tftpboot the firmware:
$ tftpboot $kernel_addr_r openwrt-mvebu-cortexa53-globalscale_espressobin-ultra-initramfs-kernel.bin
$ tftpboot $fdt_addr_r armada-3720-espressobin-ultra.dtb
Set the console and boot the image:
$ setenv bootargs $console
$ booti $kernel_addr_r - $fdt_addr_r
Once the initramfs is booted, transfer openwrt-mvebu-cortexa53-globalscale_espressobin-ultra-squashfs-sdcard.img.gz
to /tmp dir on the device.
Gunzip and dd the image:
$ gunzip /tmp/openwrt-mvebu-cortexa53-globalscale_espressobin-ultra-squashfs-sdcard.img.gz
$ dd if=/tmp/openwrt-mvebu-cortexa53-globalscale_espressobin-ultra-squashfs-sdcard.img of=/dev/mmcblk0 && sync
Reboot the device.
Signed-off-by: Vladimir Vid <vladimir.vid@sartura.hr>
