This patch removes a typo (extra "0") so that the 'cpu-alert6'
step is triggered once the system reaches 85°C.
Note: Unless the WNDR4700 is placed in an hot oven, the
hardware-monitor will never reach this value.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Rather than wait until the patches hit vanilla and
get backported via the stable kernel, this patch
patches the crypto4xx driver with the latest fixes
from the upstream linux-crypto tree.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
In the past, the MX60(W)'s recovery images always had problems
with the size restriction and never really worked without manual
intervention. This patch reworks the initramfs, which allows the
device to ease up on the impossible tight kernel size requirements
for the initramfs image.
This new initramfs can be loaded through the MX60(W) U-boot
in the following way:
=> setenv bootargs console=ttyS0,$baudrate
=> tftpboot $meraki_loadaddr meraki_mx60-initramfs-kernel.bin
[...]
Load address: 0x800000
Loading: ################################################ [...]
done
[...]
=> bootm $fileaddr
\## Booting kernel from Legacy Image at 00800000 ...
...
For more information and the latest flashing guide:
please visit the OpenWrt Wiki Page for the MX60(W):
<https://openwrt.org/toh/meraki/mx60#flashing>
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
(cherry picked from commit 36c19c9f0b)
This remedies an issue with the MBL Duo if both disks are inserted
and contain OpenWrt. kernel and dtb would be loaded from SATA 1:1
while rootfs (/dev/sda2) would be mounted on SATA 0:1.
Such a mix&match would obviously only work if both OpenWrt versions/
builds are identical, and especially fail after sysupgrade upgraded
the system disk on SATA 0:1.
The fallback to SATA 1:1 needs to be kept for MBL Single (only has
SATA 1:1) and MBL Duo with one disk inserted on SATA 1:1. To speed
up booting in those cases, the unneccesarily doubled "sata init"
will only be called once. (In theory it could be omitted completely
since the on-flash boot script already initializes SATA to load the
on-disk boot script.)
Tested on MBL Duo (all possible combination of disks) and MBL Single
Signed-off-by: Freddy Leitner <hello@square.wf>
Acked-by: Christian Lamparter <chunkeey@gmail.com>
This was not converted to the new, dt-based board name.
Fixes: e90dc8d272 ("apm821xx: convert to device-tree board detection")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The original vendor's driver programmed the dma controller's
AHB HPROT values to enable bufferable, privileged mode. This
along with the "same priorty for both channels" fixes the
freezes according to @takimata, @And.short, that have been
reported on the forum by @ticerex.
Furtheremore, @takimata reported that the patch also improved
the performance of the HDDs considerably:
|<https://forum.lede-project.org/t/wd-mybook-live-duo-two-disks/16195/55>
|It seems your patch unleashed the full power of the SATA port.
|Where I was previously hitting a really hard limit at around
|82 MB/s for reading and 27 MB/s for writing, I am now getting this:
|
|root@OpenWrt:/mnt# time dd if=/dev/zero of=tempfile bs=1M count=1024
|1024+0 records in
|1024+0 records out
|real 0m 13.65s
|user 0m 0.01s
|sys 0m 11.89s
|
|root@OpenWrt:/mnt# time dd if=tempfile of=/dev/null bs=1M count=1024
|1024+0 records in
|1024+0 records out
|real 0m 8.41s
|user 0m 0.01s
|sys 0m 4.70s
|
|This means: 121 MB/s reading and 75 MB/s writing!
|
|[...]
|
|The drive is a WD Green WD10EARX taken from an older MBL Single.
|I repeated the test a few times with even larger files to rule out
|any caching, I'm still seeing the same great performance. OpenWrt is
|now completely on par with the original MBL firmware's performance.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Starting with 4.14, the "amcc,dwc-otg" needs to be used
in order to get the usb-otg to work.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
(cherry picked from commit 12b80f1cab)
Refreshed patches. The following patches were upstreamed and have been deleted:
* target/linux/lantiq/patches-4.14/0025-MIPS-lantiq-gphy-Remove-reboot-remove-reset-asserts.patch
* target/linux/generic/pending-4.14/101-clocksource-mips-gic-timer-fix-clocksource-counter-w.patch
* target/linux/generic/pending-4.14/103-MIPS-c-r4k-fix-data-corruption-related-to-cache-coherence.patch
* target/linux/generic/pending-4.14/181-net-usb-add-lte-modem-wistron-neweb-d18q1.patch
Compile-tested: ramips/mt7621, x86/64
Run-tested: ramips/mt7621
Signed-off-by: Stijn Segers <foss@volatilesystems.org>
THIN_ARCHIVES option is enabled by default in the kernel configuration
and no one target config disables it. So enable it by default and remove
this symbol from target specific configs to keep them light.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
(cherry picked from commit 67a3cdcbb0)
New FUTEX_PI configuration symbol enabled if FUTEX and RT_MUTEX symbols
are enabled. Both of these symbols are enabled by default in the
generic config, so enable FUTEX_PI by default too to keep platform
specific configs minimal.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
(cherry picked from commit bdc2b58c4b)
OVERLAY_FS config symbol selects EXPORTFS since 4.12 kernel, we have
OVERLAY_FS enabled by default, so enable EXPORTFS in the generic config
of 4.14 and remove this option from platform specific configs.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
(cherry picked from commit a08b0d0c31)
DRM_LIB_RANDOM config symbol selected only by DRM_DEBUG_MM_SELFTEST
which is disable by default, so disable DRM_LIB_RANDOM by default too.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
(cherry picked from commit 978543a246)
These options do not used by any supported arch, so disable them by
default to make arch configs a bit more clean.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
(cherry picked from commit ead26e9db6)
Only one arch (x86_64) enables this option. So disable
ARCH_WANTS_THP_SWAP by default and remove referencies to it from all
configs (except x86_64) to make them clean.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
(cherry picked from commit f928c338ad)
This patch backports several patches that went upstream into
Herbert Xu's cryptodev-2.6 tree:
crypto: Use zeroing memory allocator instead of allocator/memset
crypto: crypto4xx - performance optimizations
crypto: crypto4xx - convert to skcipher
crypto: crypto4xx - avoid VLA use
crypto: crypto4xx - add aes-ctr support
crypto: crypto4xx - properly set IV after de- and encrypt
crypto: crypto4xx - extend aead fallback checks
crypto: crypto4xx - put temporary dst sg into request ctx
The older, outstanding patches from 120-wxyz series have been
upstreamed as well and therefore they have been reassigned to
fit into the series.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
(cherry picked from commit 16e39624b7)
The swconfig package is part of the DEFAULT_PACKAGES list in
the apm821xx's nand subtarget. It's enabled by default because
the MX60(W) and WNDR4700 need it for their initramfs. However
the package is not necessary for the MR24's sysupgrade image, as
the MR24 does not have a switch.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
(cherry picked from commit e6e51ce87f)
Merge the two existing functions and use a parameter for the type
header field.
It updates the syntax of the former mpc85xx fake ramdisk header
command to be compatible with mkimage from u-boot 2018.03 and fixes the
build error spotted by the build bot.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The MX60's uboot disables all the PHYs before starting linux.
This causes the PHY/switch detection code to malfunction
almost all of the time. To get around this, set a compatible
flag to force PHYID.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
This patch cleans and reworks the WNDR4700 dts to increase the
now combined dtb+kernel partition to 3.5 MiB. This has become
necessary due to the switch to GCC 7.3 and the ever increasing
kernel binary size.
The dtb+kernel partition was combined in order to finally
fix the problem with out-of-sync device-trees. From now
on, the kernel and device-tree will always be updated together.
Upgrade Note:
Existing installations will have to use the TFTP firmware
recovery option in order to install the update. Affected users
are advised to make a backup of their existing configuration
prior to running sysupgrade:
<https://openwrt.org/docs/guide-user/installation/generic.backup#backup_openwrt_configuration>
Due to the repartitioning of the NAND, the generated backup
should be placed on either the internal HDD, an attached
USB-Stick or on another PC (externally).
To manually trigger the firmware recovery, the reset button has
to be pressed (and hold) during boot. U-boot will enter the "Upgrade
Mode" and starts a tftpserver listening on 192.168.1.1 for a
tftp client from one of the four LAN/Ethernet ports to connect and
upload the new system: (enable tftp binary mode!).
openwrt-apm821xx-nand-netgear_wndr4700-squashfs-factory.img
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The recent change to switch to gcc 7.3 broke the image
generation code, as the kernel would no longer fit into
KERNEL_SIZE.
This patch fixes the issue by reworking the initramfs
creation and packaging, which will get rid of the
KERNEL_SIZE check in the process.
This new initramfs can be loaded through the MR24 U-boot
in the following way:
=> setenv ipaddr 192.168.1.1
=> setenv bootargs console=ttyS0,$baudrate
=> tftpboot c00000 192.168.1.2:meraki_mr24-initramfs-kernel.bin
[...]
Load address: 0xc00000
Loading: ################################################ [...]
done
Bytes transferred = 5952544 (5ad420 hex)
=> bootm $fileaddr
\## Booting kernel from Legacy Image at 00c00000 ...
...
For more information and the latest flashing guide:
please visit the OpenWrt Wiki Page for the MR24:
<https://openwrt.org/toh/meraki/mr24#flashing>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
Right patch version this time, sorry!
* Patch 180-usb-xhci-add-support-for-performing-fake-doorbell.patch had to be adjusted slightly because of upstream adapted code.
* Refreshed patches.
Compile-tested: ramips/mt7621, x86/64
Run-tested: ramips/mt7621, x86/64
Signed-off-by: Stijn Segers <foss@volatilesystems.org>
Tested-by: Rosen Penev <rosenp@gmail.com>
The missing CONFIG_USB_XHCI_PCI dependency on CONFIG_USB_PCI of the
µPD720201 xhci-pci(e) usb 3.0 chip used by the WNDR4700 was fixed with
6112abf186 ("kernel: enable CONFIG_USB_PCI for PCI usb modules").
Commit c38fb58576 ("kernel: fix disabling common usb quirks on 4.14")
finally fixed the following build error:
drivers/usb/host/xhci-pci.c: In function 'xhci_pci_probe':
drivers/usb/host/xhci-pci.c:749:6: error: implicit declaration of function 'usb_xhci_needs_pci_reset' [-Werror=implicit-function-declaration]
if (usb_xhci_needs_pci_reset(dev)) {
Hence the CONFIG_USB_PCI symbol isn't required any longer in target kernel
config.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Calling nand_do_upgrade() from platform_pre_upgrade() was deprecated
with 30f61a34b4 ("base-files: always use staged sysupgrade").
Update the platform upgrade code to use platform_do_upgrade() for NAND
images as well.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The watchdog kill command was meant for busybox watchdog. Busybox watchdog
was replaced by the procd watchdog mid 2013 with commit df7ce9301a
("busybox: disable the watchdog utility by default"), which makes the kill
command obsolete since quite some time.
Signed-off-by: Mathias Kresin <dev@kresin.me>
This patch updates the apm821xx target to use the 4.14 kernel.
4.14 finally ships with a driver for the WNDR4700's tc654 fan
controller. The custom driver is deprecated in favor of the
upstream driver and the thermal cooling definitions in the DTS
are updated.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch converts all apm821xx devices to the device-tree
board-detection method. All instances of the legacy
boardnames (mbl,mr24,...) are converted to "vendor,device"
identifier.
The custom board-detection code in apm821xx.sh is removed as
it no longer serves any purpose.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch enables metadata-supported image verification
for all apm821xx supported devices. Since this method comes
with a built-in image verification tool (fwtool), the previous
image checks can be removed.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Currently, the device name handle does not include the
manufacturer. This can make it hard do differentiate
between products from different vendors that have the
same product name. As the handle is used to derive
the image name.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch rename all the DT source files in order to
match upstream's "manufacturer-device.dts" format.
Please note that the DEVICE_DTB isn't changed. This is
because the u-boot of the MyBook Live defines the
fdt_file variable to be "apollo3g/apollo3g.dtb".
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Meraki choose to use their product's codename as the main
compatible string. Mathias Kresin commented that this is
a poor choice as this will confuse the users and devs once
the device-tree compatible is used for board-detection and
possible the image name.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch appends the "apm,bluestone" or "amcc,apollo3g"
machine compatible string to the current device tree source.
Please note that unlike other archs the PPC DT code does
not regard the machine's compatible string as a priority
list. This is explained in the kernel's usage-model.txt as follows:
"PowerPC uses a slightly different scheme where it calls the .probe()
hook from each machine_desc, and the first one returning TRUE is used.
However, this approach does not take into account the priority of the
compatible list, and probably should be avoided for new architecture
support."
For this reason, the "apm,bluestone" compatible string can't be
added to the WNDR4700. As otherwise the target specific pci
fix-up code will get ignored and this causes the ath9k WIFI
to not get initialized.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
