205-fix-headers_install.patch is obseleted by upstream commit 3246a0352e3d58380b9386570f1db1faf7edf8a8
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 41351
With this patch the mips74k subtarget will be compiled with optimized
compiler options to generated smaller and faster code. This currently
breaks broadcom-wl, because the binary blob is only compiled with
mipsr1 support.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 41050
This fixes some strange problems with tg3. I assume that the Ethernet
driver was not brought up if the switch was named switch0.
This was reported and tested by ernesto (Faulp3lz).
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 41042
All new devices (with MIPS 74K CPU) are based on BCMA SoC and have
Ethernet core supported by bgmac. Create a new subtarget to generate
optimized builds.
This is just a beginning, further tweaks (like kernel configuration)
are still possible. This decreases default root.squashfs by ~128 kB.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 41025
This allows creating more subtargets and optimize builds per family.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 41024
ARGC is a 'C-ism', but not known/valid in shell-syntax - insert the correct
var $# (=number of args) here. under normal conditions this had no impact,
but we should at least correct it. the error was observable like this:
root@box:~ [ -e "/etc/functions.sh" ] && . /etc/functions.sh
root@box:~ [ -e "/lib/functions.sh" ] && . /lib/functions.sh
root@box:~ . /lib/upgrade/platform.sh
root@box:~ . /lib/upgrade/common.sh
root@box:~ platform_check_image /tmp/myfirmware.bin
ash: bad number
root@box:~ echo $?
0
Signed-off-by: Bastian Bittorf <bittorf@bluebottle.com>
SVN-Revision: 40915
We should be more careful and don't generate 128K JFFS2 images for
devices with flashes using 64K blocks (nor the other way).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 40762
Handle it by creating a new patch for simple database changes.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 40345
And while at it, fix the nomenclature, BCM947xx/953xx refer to specific boards,
while BCM47xx/BCM53xx refer to chip identification number.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 39841
Let the switch start the carrier and set the duplex mode independently
if this nic is up of not.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 39733
We did not start the PHY when an external phy was in use. Without this
patch the driver uses half duplex mode and the switch uses full duplex
mode, which causes problems.
Thank you fback for spotting this problem.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 39719
It was recently sent to linux-mips for comments. It adds workaround for
WNR3500L to enable USB port.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 39469
Instead of looking into the proc entry provided by broadcom-diag use
the board info from /proc/cpuinfo to get the board we are on.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 39256
Use the new led api also on brcm47xx.
The led for failsafe indication is searched for.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 39255
Remove the code used on the old switch driver.
The Ethernet drive is loaded as a module and needs some time to get up
therefor we added some wait function.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 39254
This makes brcm47xx target use the default gpio led and button driver
and not broadcom-diag any more.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 39253
This breaks some devices where the serial console is not at port 0 but
somewhere else.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 39060
