Recent backport patch b5cb5f352d had missed changing the macaddr_factory address location.
This patch corrects the address location.
Fixes: b5cb5f352d ("ramips: fix WAN mac address allocation for Unielec 01 and 06 models")
Signed-off-by: David Bentham <db260179@gmail.com>
[Fix dts node name too]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Manufacturer has predetermined mac address values for lan and wan ports.
This change keeps inline with other mt7621 devices mac address allocation
from factory mtd partition.
Example from hexdump output:
0xe000 0x6 (lan) - 0xe006 0x6 (wan)
0000e000 70 b3 d5 10 02 96 70 b3 d5 10 02 95 ff ff ff ff
Previous change had created an overlapping mac address situation as it
would increment by one based on the lan mac address location found in the
factory partition, which would sometimes increment to the same as the
mt7603 wifi chip.
Tested on Unielec u7621-01 model
Signed-off-by: David Bentham <db260179@gmail.com>
(cherry picked from commit 67660d3667)
Convert this series by moving the definitions to the individual
devices.
Now all devices on ramips are converted.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
UniElec U7621-01 is a router platform board, the smaller model of
the U7621-06.
The device has the following specifications:
- MT7621AT (880 MHz)
- 256 of RAM (DDR3)
- 16 MB of FLASH (SPI NOR)
- 5x 1 Gbps Ethernet (MT7621 built-in switch)
- 1x 2.4Ghz MT7603E
- 1x 5Ghz MT7612
- 1x miniPCIe slots (PCIe bus only)
- 1x miniSIM slot
- 1x USB 2.0 (uses the usb 3.0 driver)
- 8x LEDs (1x GPIO-controlled)
- 1x reset button
- 1x UART header (4-pins)
- 1x GPIO header (30-pins)
- 1x DC jack for main power (12 V)
The following has been tested and is working:
- Ethernet switch
- 1x 2.4Ghz MT7603E (wifi)
- 1x 5Ghz MT7612 (wifi)
- miniPCIe slots (tested with Wi-Fi cards and LTE modem cards)
- miniSIM slot (works with normal size simcard)
- sysupgrade
- reset button
Installation:
This board has no locked down bootloader. The seller can be asked to
install openwrt v18.06, so upgrades are standard sysupgrade method.
Recovery:
This board contains a Chinese, closed-source bootloader called Breed
(Boot and Recovery Environment for Embedded Devices). Breed supports web
recovery and to enter it, you keep the reset button pressed for around
5 seconds during boot. Your machine will be assigned an IP through DHCP
and the router will use IP address 192.168.1.1. The recovery website is
in Chinese, but is easy to use. Click on the second item in the list to
access the recovery page, then the second item on the next page is where
you select the firmware. In order to start the recovery, you click the
button at the bottom.
LEDs list (left to right):
- ESW_P0_LED_0
- ESW_P1_LED_0
- ESW_P2_LED_0
- ESW_P3_LED_0
- ESW_P4_LED_0
- CTS2_N (GPIO10, configured as "status" LED)
- LED_WLAN# (connected with pin 44 in wifi1 slot)
Signed-off-by: David Bentham <db260179@gmail.com>
[add DEVICE_VARIANT, fix DEVICE_PACKAGES, remove &gpio]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
