Remove upstreamed from 2.11 release:
060-nl80211-fix-crash-when-adding-an-interface-fails.patch
Rebase all other patches
Signed-off-by: Ivan Pavlov <AuthorReflex@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16338
Signed-off-by: Robert Marko <robimarko@gmail.com>
This brings many changes, including fixes for a couple of memory leaks,
and improved interoperability with 802.11r. There are also many changes
related to 802.11be, which is not enabled at this time.
Fixed upstream:
- 022-hostapd-fix-use-of-uninitialized-stack-variables.patch
- 180-driver_nl80211-fix-setting-QoS-map-on-secondary-BSSs.patch
- 993-2023-10-28-ACS-Fix-typo-in-bw_40-frequency-array.patch
Switch PKG_SOURCE_URL to https, since http is not currently working.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
Tested-by: Ilya Katsnelson <me@0upti.me>
Tested by: Andrew Sim <andrewsimz@gmail.com>
This is not activated by default and must be explicitly enabled via ubus
It supports reporting log messages and netlink packets
Signed-off-by: Felix Fietkau <nbd@nbd.name>
When STA is disconnected, ensure that the interface is in a cleanly stopped
state:
- if in regular enable/disable state, stop beacons if necessary
- in any other state, disable the interface
When the STA is up, ignore repeated start commands for the same channel, in
order to avoid unnecessary AP restarts
Signed-off-by: Felix Fietkau <nbd@nbd.name>
set_config causes the ucode bss resource to be re-created and because of that
the bss list needs to be updated as well
Signed-off-by: Felix Fietkau <nbd@nbd.name>
When switching from a STA-only configuration to AP+STA on the same phy, the
STA was previously restarted in order to notify hostapd of the new frequency,
which might not match the AP configuration.
Fix the STA restart by querying the operating frequency from within hostapd
when bringing up the AP.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
It cannot be properly cloned, since it is attached to the resource type.
Use a separate registry for data. Fixes object confusion issues
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Drop obsolete control interface patches.
This fixes some corner cases in the previous code where the segment 0 center
frequency was not adjusted properly, leading to logspam and non-working AP
interfaces.
Additionally, shutting down the AP was broken, because the next beacon update
would re-enable it, leading to a race condition on assoc.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This implements vastly improved dynamic configuration reload support.
It can handle configuration changes on individual wifi interfaces, as well
as adding/removing interfaces.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This can be used to run a standalone EAP server that can be used from
other APs. It uses json as user database format and can automatically
handle reload.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
hostapd's compile time option CONFIG_IEEE80211N was removed almost 3 years
ago, 80.211n/HT is always included since then.
Noticed because `hostapd -v11n` confusingly returned an error.
See hostapd's commit:
f3bcd69603 "Remove CONFIG_IEEE80211N build option"
Signed-off-by: Andre Heider <a.heider@gmail.com>
eee80211_frequency_to_channel() isn't used anymore, which is a leftover from:
2a31e9ca97 "hostapd: add op-class to get_status output"
Signed-off-by: Andre Heider <a.heider@gmail.com>
Add the measurement report value to the beacon reports send via ubus. It
is possible to derive from the measurement report if a station refused to
do a beacon report and why. It is important to know why a station refuses
to do a beacon-report. In particular, we should not request a beacon
report from a station again that refused a beacon-report before.
The rejection reasons can be found by looking at the bits defined by:
- MEASUREMENT_REPORT_MODE_ACCEPT
- MEASUREMENT_REPORT_MODE_REJECT_LATE
- MEASUREMENT_REPORT_MODE_REJECT_INCAPABLE
- MEASUREMENT_REPORT_MODE_REJECT_REFUSED
Suggested-by: Ian Clowes <clowes_ian@hotmail.com>
Signed-off-by: Nick Hainke <vincent@systemli.org>
Also include the station auth_type in the ubus and log message in order
to detect, if clients used FT or FILS to associate
Signed-off-by: Felix Fietkau <nbd@nbd.name>
There is no WLAN_STA_MBO flag, but according to the hostapd source code,
when an STA does not support MBO, cell_capa will be 0. Use this to
indicate MBO support in the get_clients ubus method.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Reviewed-by: David Bauer <mail@david-bauer.net>
Operating Channel Validation (OCV) is a security feature designed to
prevent person-in-the-middle multi-channel attacks. Compile the -basic and
-full variants of hostapd with this feature, and enable discovery of this
feature for future luci integration. OCV can be configured by setting ocv
equal to one of the following values in the wireless config:
0 = disabled (hostapd/wpa_supplicant default)
1 = enabled
2 = enabled in workaround mode - Allow STA that claims OCV capability to
connect even if the STA doesn't send OCI or negotiate PMF.
Signed-off-by: Michael Yartys <michael.yartys@protonmail.com>
Support the use of MBO in the bss_transition_request ubus method.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: David Bauer <mail@david-bauer.net>
Add the current BSS color to hostapd get_status method. This field is
set to -1 in case BSS color is not active for the BSS.
Signed-off-by: David Bauer <mail@david-bauer.net>
Tested-by: Stijn Tintel <stijn@linux-ipv6.be>
Update hostapd to Git HEAD from 2022-05-08. This allows us to take
advantage of background radar-detection as well as BSS color collision
detection.
Suggested-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: David Bauer <mail@david-bauer.net>
Tested-by: Stijn Tintel <stijn@linux-ipv6.be>
