PROVIDES for these packages will cause ambiguity and circular dependency
in planned changes.
For example, if there is a package `brcmfmac-firmware-43455-sdio-rpi-cm4`
that depends on `brcmfmac-firmware-43455-sdio-rpi-4b`, there is no way to
tell which one of below packages the system will go for.
- package named `brcmfmac-firmware-43455-sdio-rpi-4b`
- package named `cypress-nvram-43455-sdio-rpi-4b` that PROVIDES
`brcmfmac-firmware-43455-sdio-rpi-4b`
When ambiguity is unacceptable, PROVIDES (aliases) shall be removed and
packages shall only be used through their exact name.
So remove PROVIDES and keep only CONFLICTS.
Signed-off-by: Kuan-Yi Li <kyli@abysm.org>
Realtek bluetooth devices need firmware. Add packages for some of
these.
Tested on a WNDR3700v4 with rtl8761bu firmware.
Signed-off-by: Quintin Hill <stuff@quintin.me.uk>
Changes:
712460c linux-firmware: Update firmware file for Intel Bluetooth 9462
90d5f7e linux-firmware: Update firmware file for Intel Bluetooth 9462
48954ba linux-firmware: Update firmware file for Intel Bluetooth 9560
0e205fd linux-firmware: Update firmware file for Intel Bluetooth 9560
06b941e linux-firmware: Update firmware file for Intel Bluetooth AX201
ba958ff linux-firmware: Update firmware file for Intel Bluetooth AX201
02bdea2 linux-firmware: Update firmware file for Intel Bluetooth AX211
7044d46 linux-firmware: Update firmware file for Intel Bluetooth AX211
1b99bcd linux-firmware: Update firmware file for Intel Bluetooth AX210
4668ae9 linux-firmware: Update firmware file for Intel Bluetooth AX200
5bdfdba linux-firmware: Update firmware file for Intel Bluetooth AX201
b0f995c amdgpu: update DMCUB firmware for DCN 3.1.6
d991031 rtl_bt: Update RTL8822C BT UART firmware to 0xFFB8_ABD6
fd62f01 rtl_bt: Update RTL8822C BT USB firmware to 0xFFB8_ABD3
b15fc21 WHENCE: mrvl: prestera: Add WHENCE entries for newly updated 4.1 FW images
bf5a337 mrvl: prestera: Update Marvell Prestera Switchdev FW to v4.1
4a733c2 iwlwifi: add new FWs from core74_pv-60 release
7d2bb50 qcom: drop split a530_zap firmware file
7d56713 qcom/vpu-1.0: drop split firmware in favour of the mbn file
1431496 qcom/venus-4.2: drop split firmware in favour of the mbn file
cf95783 qcom/venus-4.2: replace split firmware with the mbn file
1fe6f49 qcom/venus-1.8: replace split firmware with the mbn file
abc0302 linux-firmware: Add firmware for Cirrus CS35L41 on new ASUS Laptop
20d9516 iwlwifi: add new PNVM binaries from core74-44 release
06dbfbc iwlwifi: add new FWs from core69-81 release
05df8e6 qcom: update venus firmware files for VPU-2.0
cd6fcdb qcom: remove split SC7280 venus firmware images
1612706 qcom: update venus firmware file for v5.4
ad9fdba qcom: replace split SC7180 venus firmware images with symlink
dae5d46 rtw89: 8852b: update fw to v0.27.32.1
a8e86ec rtlwifi: update firmware for rtl8192eu to v35.7
9aa8db1 rtlwifi: Add firmware v4.0 for RTL8188FU
8f86b5a i915: Add HuC 7.10.3 for DG2
48407ff cnm: update chips&media wave521c firmware.
bd31846 brcm: add symlink for Pi Zero 2 W NVRAM file
771968c linux-firmware: Add firmware for Cirrus CS35L41 on ASUS Laptops
6f9620e linux-firmware: Add firmware for Cirrus CS35L41 on Lenovo Laptops
1d18cb9 linux-firmware: Add firmware for Cirrus CS35L41 on HP Laptops
e497757 rtw89: 8852b: add initial fw v0.27.32.0
98b5577 iwlwifi: add new FWs from core72-129 release
604026c iwlwifi: update 9000-family firmwares to core72-129
Signed-off-by: Nick Hainke <vincent@systemli.org>
Specifications:
SOC: Qualcomm IPQ4018 (DAKOTA) ARM Quad-Core
RAM: 256 MiB
FLASH1: 4 MiB NOR
FLASH2: 128 MiB NAND
ETH: Qualcomm QCA8075
WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11b/g/n 2x2
WLAN2: Qualcomm Atheros QCA4018 5G 802.11n/ac W2 2x2
USB: 1 x USB 3.0 port
Button: 1 x Reset button
Switch: 1 x Mode switch
LED: 1 x Blue LED + 1 x White LED
Install via uboot tftp or uboot web failsafe.
By uboot tftp:
(IPQ40xx) # tftpboot 0x84000000 openwrt-ipq40xx-generic-glinet_gl-a1300-squashfs-nand-factory.ubi
(IPQ40xx) # nand erase 0 0x8000000
(IPQ40xx) # nand write 0x84000000 0 $filesize
By uboot web failsafe:
Push the reset button for 10 seconds util the power led flash faster,
then use broswer to access http://192.168.1.1
Afterwards upgrade can use sysupgrade image.
Signed-off-by: Weiping Yang <weiping.yang@gl-inet.com>
Get rid of drivers that are either limited to 802.11b/g or don't even support
cfg80211/mac80211. Most of these are either limited to boards that we don't even
support anymore because of firmware size, or were only used for custom hacks by
a really small number of users in the past.
Let's get rid of those to reduce the maintenance effort and the number of useless
packages
Signed-off-by: Felix Fietkau <nbd@nbd.name>
It's a 4G Cat.20 router used by Vodafone Italy (called Vodafone FWA)
and Vodafone DE\T-Mobile PL (called GigaCube).
Modem is a MiniPCIe-to-USB based on Snapdragon X24,
it supports 4CA aggregation.
There are currently two hardware revisions, which
differ on the 5Ghz radio:
AT1 = QCA9984 5Ghz Radio on PCI-E bus
AT2 = IPQ4019 5Ghz Radio inside IPQ4019 like 2.4Ghz
Device specification
--------------------
SoC Type: Qualcomm IPQ4019
RAM: 256 MiB
Flash: 128 MiB SPI NAND (Winbond W25N01GV)
ROM: 2MiB SPI Flash (GD25Q16)
Wireless 2.4 GHz (IP4019): b/g/n, 2x2
Wireless 5 GHz:
(QCA9984): a/n/ac, 4x4 HW REV AT1
(IPA4019): a/n/ac, 2x2 HW REV AT2
Ethernet: 2xGbE (WAN/LAN1, LAN2)
USB ports: No
Button: 2 (Reset/WPS)
LEDs: 3 external leds: Network (white or red), Wifi, Power and 1 internal (blue)
Power: 12 VDC, 1 A
Connector type: Barrel
Bootloader: U-Boot
Installation
------------
1. Place OpenWrt initramfs image for the device on a TFTP
in the server's root. This example uses Server IP: 192.168.0.2
2. Connect serial console (115200,8n1) to serial connector
GND (which is right next to the thing with MF289F MIMO-V1.0), RX, TX
(refer to this image: https://ibb.co/31Gngpr).
3. Connect TFTP server to RJ-45 port (WAN/LAN1).
4. Stop in u-Boot (using ESC button) and run u-Boot commands:
setenv serverip 192.168.0.2
setenv ipaddr 192.168.0.1
set fdt_high 0x85000000
tftp openwrt-ipq40xx-generic-zte_mf289f-initramfs-fit-zImage.itb
bootm $loadaddr
5. Please make backup of original partitions, if you think about revert to
stock, specially mtd16 (Web UI) and mtd17 (rootFS).
Use /tmp as temporary storage and do:
WEB PARITION
--------------------------------------
cat /dev/mtd16 > /tmp/mtd16.bin
scp /tmp/mtd16.bin root@YOURSERVERIP:/
rm /tmp/mtd16.bin
ROOT PARITION
--------------------------------------
cat /dev/mtd17 > /tmp/mtd17.bin
scp /tmp/mtd17.bin root@YOURSERVERIP:/
rm /tmp/mtd17.bin
6. Login via ssh or serial and remove stock partitions
(default IP 192.168.0.1):
# this can return an error, if ubi was attached before
# or rootfs part was erased before.
ubiattach -m 17
# it could return error if rootfs part was erased before
ubirmvol /dev/ubi0 -N ubi_rootfs
# some devices doesn't have it
ubirmvol /dev/ubi0 -N ubi_rootfs_data
7. download and install image via sysupgrade -n
(either use wget/scp to copy the mf289f's squashfs-sysupgrade.bin
to the device's /tmp directory)
sysupgrade -n /tmp/openwrt-...-zte_mf289f-squashfs-sysupgrade.bin
Sometimes it could print ubi attach error, but please ignore it
if process goes forward.
Flash Layout
NAND:
mtd8: 000a0000 00020000 "fota-flag"
mtd9: 00080000 00020000 "0:ART"
mtd10: 00080000 00020000 "mac"
mtd11: 000c0000 00020000 "reserved2"
mtd12: 00400000 00020000 "cfg-param"
mtd13: 00400000 00020000 "log"
mtd14: 000a0000 00020000 "oops"
mtd15: 00500000 00020000 "reserved3"
mtd16: 00800000 00020000 "web"
mtd17: 01d00000 00020000 "rootfs"
mtd18: 01900000 00020000 "data"
mtd19: 03200000 00020000 "fota"
mtd20: 0041e000 0001f000 "kernel"
mtd21: 0101b000 0001f000 "ubi_rootfs"
SPI:
mtd0: 00040000 00010000 "0:SBL1"
mtd1: 00020000 00010000 "0:MIBIB"
mtd2: 00060000 00010000 "0:QSEE"
mtd3: 00010000 00010000 "0:CDT"
mtd4: 00010000 00010000 "0:DDRPARAMS"
mtd5: 00010000 00010000 "0:APPSBLENV"
mtd6: 000c0000 00010000 "0:APPSBL"
mtd7: 00050000 00010000 "0:reserved1"
Back to Stock (!!! need original dump taken from initramfs !!!)
-------------
1. Place mtd16.bin and mtd17.bin initramfs image
for the device on a TFTP in the server's root.
This example uses Server IP: 192.168.0.2
2. Connect serial console (115200,8n1) to serial console
connector (refer to the pin-out from above).
3. Connect TFTP server to RJ-45 port (WAN/LAN1).
4. rename mtd16.bin to web.img and mtd17.bin to root_uImage_s
5. Stop in u-Boot (using ESC button) and run u-Boot commands:
This will erase RootFS+Web:
nand erase 0x1000000 0x800000
nand erase 0x1800000 0x1D00000
This will restore RootFS:
tftpboot 0x84000000 ${dir}root_uImage_s
nand erase 0x1800000 0x1D00000
nand write $fileaddr 0x1800000 $filesize
This will restore Web Interface:
tftpboot 0x84000000 ${dir}web.img
nand erase 0x1000000 0x800000
nand write $fileaddr 0x1000000 $filesize
After first boot on stock firwmare, do a factory reset.
Push reset button for 5 seconds so all parameters will
be reverted to the one printed on label on bottom of the router
Signed-off-by: Giammarco Marzano <stich86@gmail.com>
Reviewed-by: Lech Perczak <lech.perczak@gmail.com>
(Warning: commit message did not conform to UTF-8 - hopefully fixed?,
added description of the pin-out if image goes down, reformatted
commit message to be hopefully somewhat readable on git-web,
redid some of the gpio-buttons & leds DT nodes, etc.)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Sony NCP-HG100/Cellular is a IoT Gateway with 2.4/5 GHz band 11ac
(WiFi-5) wireless function, based on IPQ4019.
Specification:
- SoC : Qualcomm IPQ4019
- RAM : DDR3 512 MiB (H5TC4G63EFR)
- Flash : eMMC 4 GiB (THGBMNG5D1LBAIT)
- WLAN : 2.4/5 GHz 2T2R (IPQ4019)
- Ethernet : 10/100/1000 Mbps x2
- Transceiver : Qualcomm QCA8072
- WWAN : Telit LN940A9
- Z-Wave : Silicon Labs ZM5101
- Bluetooth : Qualcomm CSR8811
- Audio DAC : Realtek ALC5629
- Audio Amp. : Realtek ALC1304
- Voice Input Processor : Conexant CX20924
- Micro Controller Unit : Nuvoton MINI54FDE
- RGB LED, Fan, Temp. sensors
- Touch Sensor : Cypress CY8C4014LQI
- RGB LED driver : TI LP55231 (2x)
- LEDs/Keys : 11x, 6x
- UART : through-hole on PCB
- J1: 3.3V, TX, RX, GND from tri-angle marking
- 115200n8
- Power : 12 VDC, 2.5 A
Flash instruction using initramfs image:
1. Prepare TFTP server with the IP address 192.168.132.100 and place the
initramfs image to TFTP directory with the name "C0A88401.img"
2. Boot NCP-HG100/Cellular and interrupt after the message
"Hit any key to stop autoboot: 2"
3. Perform the following commands and set bootcmd to allow booting from
eMMC
setenv bootcmd "mmc read 0x84000000 0x2e22 0x4000 && bootm 0x84000000"
saveenv
4. Perform the following command to load/boot the OpenWrt initramfs image
tftpboot && bootm
5. On the initramfs image, perform sysupgrade with the sysupgrade image
(if needed, backup eMMC partitions by dd command and download to
other place before performing sysupgrade)
6. Wait for ~120 seconds to complete flashing
Known issues:
- There are no drivers for audio-related chips/functions in Linux Kernel
and OpenWrt, they cannot be used.
- There is no driver for MINI54FDE Micro-Controller Unit, customized for
this device by the firmware in the MCU. This chip controls the
following functions, but they cannot be controlled in OpenWrt.
- RGB LED
- Fan
this fan is controlled automatically by MCU by default, without
driver
- Thermal Sensors (2x)
- Currently, there is no driver or tool for CY8C4014LQI and cannot be
controlled. It cannot be exited from "booting mode" and moved to "normal
op mode" after booting. And also, the 4x buttons (mic mute, vol down,
vol up, alexa trigger) connected to the IC cannot be controlled.
- it can be exited from "booting mode" by installing and executing
i2cset command:
opkg update
opkg install i2c-tools
i2cset -y 1 0x14 0xf 1
- There is a connection issue on the control by uqmi for the WWAN module.
But modemmanager can be used without any issues and the use of it is
recommended.
- With the F2FS format, too many errors are reported on erasing eMMC
partition "rootfs_data" while booting:
[ 1.360270] sdhci: Secure Digital Host Controller Interface driver
[ 1.363636] sdhci: Copyright(c) Pierre Ossman
[ 1.369730] sdhci-pltfm: SDHCI platform and OF driver helper
[ 1.374729] sdhci_msm 7824900.sdhci: Got CD GPIO
...
[ 1.413552] mmc0: SDHCI controller on 7824900.sdhci [7824900.sdhci] using ADMA 64-bit
[ 1.528325] mmc0: new HS200 MMC card at address 0001
[ 1.530627] mmcblk0: mmc0:0001 004GA0 3.69 GiB
[ 1.533530] mmcblk0boot0: mmc0:0001 004GA0 partition 1 2.00 MiB
[ 1.537831] mmcblk0boot1: mmc0:0001 004GA0 partition 2 2.00 MiB
[ 1.542918] mmcblk0rpmb: mmc0:0001 004GA0 partition 3 512 KiB, chardev (247:0)
[ 1.550323] Alternate GPT is invalid, using primary GPT.
[ 1.561669] mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 p11 p12 p13 p14 p15 p16 p17
...
[ 8.841400] mount_root: loading kmods from internal overlay
[ 8.860241] kmodloader: loading kernel modules from //etc/modules-boot.d/*
[ 8.863746] kmodloader: done loading kernel modules from //etc/modules-boot.d/*
[ 9.240465] block: attempting to load /etc/config/fstab
[ 9.246722] block: unable to load configuration (fstab: Entry not found)
[ 9.246863] block: no usable configuration
[ 9.254883] mount_root: overlay filesystem in /dev/mmcblk0p17 has not been formatted yet
[ 9.438915] urandom_read: 5 callbacks suppressed
[ 9.438924] random: mkfs.f2fs: uninitialized urandom read (16 bytes read)
[ 12.243332] mmc_erase: erase error -110, status 0x800
[ 12.246638] mmc0: cache flush error -110
[ 15.134585] mmc_erase: erase error -110, status 0x800
[ 15.135891] mmc_erase: group start error -110, status 0x0
[ 15.139850] mmc_erase: group start error -110, status 0x0
...(too many the same errors)...
[ 17.350811] mmc_erase: group start error -110, status 0x0
[ 17.356197] mmc_erase: group start error -110, status 0x0
[ 17.439498] sdhci_msm 7824900.sdhci: Card stuck in wrong state! card_busy_detect status: 0xe00
[ 17.446910] mmc0: tuning execution failed: -5
[ 17.447111] mmc0: cache flush error -110
[ 18.012440] F2FS-fs (mmcblk0p17): Found nat_bits in checkpoint
[ 18.062652] F2FS-fs (mmcblk0p17): Mounted with checkpoint version = 428fa16b
[ 18.198691] block: attempting to load /etc/config/fstab
[ 18.198972] block: unable to load configuration (fstab: Entry not found)
[ 18.203029] block: no usable configuration
[ 18.211371] mount_root: overlay filesystem has not been fully initialized yet
[ 18.214487] mount_root: switching to f2fs overlay
So, this support uses ext4 format instead which has no errors.
Note:
- The primary uart is shared for debug console and Z-Wave chip. The
function is switched by GPIO15 (Linux: 427).
value:
1: debug console
0: Z-Wave
- NCP-HG100/Cellular has 2x os-image pairs in eMMC.
- 0:HLOS, rootfs
- 0:HLOS_1, rootfs_1
In OpenWrt, the first image pair is used.
- "bootipq" command in U-Boot requires authentication with signed-image
by default. To boot unsigned image of OpenWrt, use "mmc read" and
"bootm" command instead.
- This support is for "Cellular" variant of NCP-HG100 and not tested on
"WLAN" (non-cellular) variant.
- The board files of ipq-wifi may also be used in "WLAN" variant of
NCP-HG100, but unconfirmed and add files as for "Cellular" variant.
- "NET" LED is used to indicate WWAN status in stock firmware.
- There is no MAC address information in the label on the case, use the
address included in UUID in the label as "label-MAC" instead.
- The "CLOUD" LEDs are partially used for indication of system status in
stock firmware, use they as status LEDs in OpenWrt instead of RGB LED
connected to the MCU.
MAC addresses:
LAN : 5C:FF:35:**:**:ED (ART, 0x6 (hex))
WAN : 5C:FF:35:**:**:EF (ART, 0x0 (hex))
2.4 GHz: 5C:FF:35:**:**:ED (ART, 0x1006 (hex))
5 GHz : 5C:FF:35:**:**:EE (ART, 0x5006 (hex))
partition layout in eMMC (by fdisk, GPT):
Disk /dev/mmcblk0: 7733248 sectors, 3776M
Logical sector size: 512
Disk identifier (GUID): ****
Partition table holds up to 20 entries
First usable sector is 34, last usable sector is 7634910
Number Start (sector) End (sector) Size Name
1 34 1057 512K 0:SBL1
2 1058 2081 512K 0:BOOTCONFIG
3 2082 3105 512K 0:QSEE
4 3106 4129 512K 0:QSEE_1
5 4130 4641 256K 0:CDT
6 4642 5153 256K 0:CDT_1
7 5154 6177 512K 0:BOOTCONFIG1
8 6178 6689 256K 0:APPSBLENV
9 6690 8737 1024K 0:APPSBL
10 8738 10785 1024K 0:APPSBL_1
11 10786 11297 256K 0:ART
12 11298 11809 256K 0:HSEE
13 11810 28193 8192K 0:HLOS
14 28194 44577 8192K 0:HLOS_1
15 44578 306721 128M rootfs
16 306722 568865 128M rootfs_1
17 568866 3958065 1654M rootfs_data
[initial work]
Signed-off-by: Iwao Yuki <dev.clef@gmail.com>
Co-developed-by: Iwao Yuki <dev.clef@gmail.com>
[adjustments, cleanups, commit message, sending patch]
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
(dropped clk_unused_ignore, dropped 901-* patches, renamed
key nodes, changed LEDs chan/labels to match func-en, made
:net -> (w)wan leds)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This package downloads raw files
which have names that are not corresponding to
the name and version of the package
as it is defined in the Makefile.
Use the option DL_SUBDIR to set the DL_DIR
to be a subdirectory named with
PKG_NAME and PKG_RELEASE
to better organize the downloads.
Signed-off-by: Michael Pratt <mcpratt@pm.me>
This package downloads raw files
which have names that are not corresponding to
the name and version of the package
as it is defined in the Makefile.
Use the option DL_SUBDIR to set the DL_DIR
to be a subdirectory named with
PKG_NAME and PKG_VERSION
to better organize the downloads.
Signed-off-by: Michael Pratt <mcpratt@pm.me>
This package downloads raw files
which have names that are not corresponding to
the name and version of the package
as it is defined in the Makefile.
Use the option DL_SUBDIR to set the DL_DIR
to be a subdirectory named with
PKG_NAME and PKG_VERSION
to better organize the downloads.
Signed-off-by: Michael Pratt <mcpratt@pm.me>
btusb fails to start on MT792[12] hardware without the appropriate
firmware being loaded first:
[ 9.750285] bluetooth hci0: Direct firmware load for mediatek/BT_RAM_CODE_MT7961_1_2_hdr.bin failed with error -2
[ 9.765723] bluetooth hci0: Falling back to sysfs fallback for: mediatek/BT_RAM_CODE_MT7961_1_2_hdr.bin
Package firmware for MediaTek MT792[12] Bluetooth from linux-firmware.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The R8712U driver depends on cfg80211. cfg80211 is provided by mac80211
backports, we can not build any in kernel drivers which depend on
cfg80211 which is an out of tree module in OpenWrt.
The cfg80211 dependency was added with kernel 5.9.
We could add rtl8192su to backports and build it from there.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The change of the PKG_VERSION caused the hash of the package to
change. This is because the PKG_VERSION is present in the
internal directory structure of the archive.
Fixes: e879cccaa2 ("uboot-layerscape: update PKG_HASH")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
those board files can/should be dropped now too.
Fixes: 50c232d6f4 ("ipq-wifi: drop upstreamed board-2.bin")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
the legacy driver was dropped in linux 5.14-rc3:
commit d249ff28b1d8 ("intersil: remove obsolete prism54 wireless driver")
Quoting Lukas Bulwahn:
"p54 replaces prism54 so users should be unaffected."
Reported-by: Marius Dinu <m95d+git@psihoexpert.ro>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The BDFs for the:
GL.iNet GL-B2200
were upstreamed to the ath10k-firmware repository
and landed in linux-firmware.git
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Kalle:
"I see that variant has a space in it, does that work it correctly? My
original idea was that spaces would not be allowed, but didn't realise
to add a check for that."
Is this an easy change? Because the original author (Tim Davis) noted:
"You may substitute the & and space with something else saner if they
prove to be problematic."
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This board features an AP6335 system-in-package combination of Wi-Fi and
Bluetooth module based on BCM4339.
Support is borrowed directly from the following Buildroot commit:
095420e05ae5: ("configs/imx7dpico: Add Wifi support").
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Old firmware provided by 'cypress-firmware' suite is not sufficient for
AP6335 module used in PICO-PI-IMX7D board to probe successfully. Use the
upstream version from linux-firmware instead.
At the same time, drop the old firmware from 'cypress-firmware' package.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
902b321 wireless-regdb: Update regulatory rules for Israel (IL)
20f6f34 wireless-regdb: add missing spaces for US S1G rules
25652b6 wireless-regdb: Update regulatory rules for Australia (AU)
081873f wireless-regdb: update regulatory database based on preceding changes
166fbdd wireless-regdb: add db files missing from previous commit
e3f03f9 Regulatory update for 6 GHz operation in Canada (CA)
888da5f Regulatory update for 6 GHz operation in United States (US)
647bcaa Regulatory update for 6 GHz operation in FI
c6b079d wireless-regdb: update regulatory rules for Bulgaria (BG) on 6GHz
2ed39be wireless-regdb: Remove AUTO-BW from 6 GHz rules
7a6ad1a wireless-regdb: Unify 6 GHz rules for EU contries
68a8f2f wireless-regdb: update regulatory database based on preceding changes
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Aruba deploys a BDF in the root filesystem, however this matches the one
used for the DK04 reference board.
The board-specific BDFs are built into the kernel. The AP-365 shows
sinificant degraded performance with increased range when used with the
reference BDF.
Replace the BDF with the one extracted from Arubas kernel.
Signed-off-by: David Bauer <mail@david-bauer.net>
Since we now provide the BDF-s for MikroTik IPQ40xx devices on the fly,
there is noneed to include package and ship them like we do now.
This also resolves the performance issues that happen as MikroTik
changes the boards and ships them under the same revision but they
actually ship with and require a different BDF.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Kalle Valo managed to add the qca9980's boardfile in the
upstream repository. Sourcing the file from his repository
is no longer needed.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
After the switch to pre-calibration, ath10k would fail to initialize
the PCIE Wi-Fi on the GL-B200 as follows:
ath10k_pci 0000:01:00.0: enabling device (0140 -> 0142)
ath10k_pci 0000:01:00.0: qca9888 hw2.0 target 0x01000000 chip_id 0x00000000 sub 0000:0000
[...]
ath10k_pci 0000:01:00.0: failed to fetch board data for bus=pci,bmi-chip-id=0,bmi-board-id=16,variant=GL-B2200 from ath10k/QCA9888/hw2.0/board-2.bin
ath10k_pci 0000:01:00.0: failed to fetch board-2.bin or board.bin from ath10k/QCA9888/hw2.0
ath10k_pci 0000:01:00.0: failed to fetch board file: -12
ath10k_pci 0000:01:00.0: could not probe fw (-12)
Repackage the BDF file after renaming relevant fields and files to
allow for the Wi-Fi interface to start again.
Fixes: 80d34d9d59 ("ipq40xx: document pcie wifi chip on the GL.Inet GL-B2200")
CC: Christian Lamparter <chunkeey@gmail.com>
CC: Robert Marko <robimarko@gmail.com>
Reviewed-by: Robert Marko <robert.marko@sartura.hr>
Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
Modified the radio frequency hardware part of e2600ac c1/c2,
need to cooperate with the modified board.bin file, the device
can work normally.
Signed-off-by: 张 鹏 <sd20@qxwlan.com>
From a manufacturer's image (version R89-13729.57.27), with appopriate
',variant=' appended to the board names:
$ .../qca-swiss-army-knife/tools/scripts/ath10k/ath10k-bdencoder \
-i ./board-google_wifi.qca4019
FileSize: 48596
FileCRC32: 3966df5d
FileMD5: d54161b0fb9e93691c4272649c37535a
BoardNames[0]: 'bus=ahb,bmi-chip-id=0,bmi-board-id=16,variant=GO_GALE'
BoardLength[0]: 12064
BoardCRC32[0]: e117f336
BoardMD5[0]: ea35e78c88a8571201da8b75edc9b881
BoardNames[1]: 'bus=ahb,bmi-chip-id=0,bmi-board-id=21,variant=GO_GALE'
BoardLength[1]: 12064
BoardCRC32[1]: 6c751ec9
BoardMD5[1]: 44cbc4ca6cb7141ba4249615f7065582
BoardNames[2]: 'bus=ahb,bmi-chip-id=0,bmi-board-id=16,variant=GO_BREEZE'
BoardLength[2]: 12064
BoardCRC32[2]: 24fba117
BoardMD5[2]: b4ac055b3ab67d5a6f5607a96af39a1f
BoardNames[3]: 'bus=ahb,bmi-chip-id=0,bmi-board-id=21,variant=GO_BREEZE'
BoardLength[3]: 12064
BoardCRC32[3]: a3e16b2a
BoardMD5[3]: 8b26cb285032314247304114b8ac50e7
Naming follows existing Google projects included in upstream board-2.bin
-- GO(ogle) prefix, an underscore (_), and the project code name, all in
caps.
Note that I only tested the "gale" model; the "breeze" model is a later
revision (same marketing name) with very small hardware changes but
otherwise using the same firmware image.
Submitted upstream here:
ath10k-firmware: QCA4019: hw1.0: Add Google Wifi BDFs
http://lists.infradead.org/pipermail/ath10k/2022-March/013465.htmlhttps://lore.kernel.org/ath10k/YjaNGW252Ls%2FyDw8@localhost/
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
- Binary files were renamed to cyfmac from brcmfmac, but the files needs
to be on the router with the previous naming
[ 6.656165] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac43455-sdio for chip BCM4345/6
[ 6.665182] brcmfmac mmc1:0001:1: Direct firmware load for brcm/brcmfmac43455-sdio.bin failed with error -2
[ 6.674928] brcmfmac mmc1:0001:1: Falling back to sysfs fallback for: brcm/brcmfmac43455-sdio.bin
- Cypress were acquired by Infineon Technologies
Thus change the project URL and switch to download files from their
GitHub repository. This is much better than the previous solution, which
requires finding new threads on their community forum about new driver
updates, and it will be necessary to change the URL each time.
Unfortunately, it seems that there is not published changelog, but
according to this forum thread [1], be careful by opening the link from
solution since it contains ending bracket ), it brings fixes for various
security vulnerabilities, which were fixed in 7_45_234.
Fixes:
- FragAttacks
- Kr00k
Also add LICENSE file
Run tested on Seeedstudio router powered by Raspberry Pi 4 CM with
package cypress-firmware-43455-sdio.
Before:
root@OpenWrt:~# dmesg | grep 'Firmware: BCM4345/6'
[ 6.895050] brcmfmac: brcmf_c_preinit_dcmds: Firmware: BCM4345/6 wl0: Mar 23 2020 02:20:01 version 7.45.206 (r725000 CY) FWID 01-febaba43
After:
root@OpenWrt:~# dmesg | grep 'Firmware: BCM4345/6'
[ 6.829805] brcmfmac: brcmf_c_preinit_dcmds: Firmware: BCM4345/6 wl0: Apr 15 2021 03:03:20 version 7.45.234 (4ca95bb CY) FWID 01-996384e2
[1] https://community.infineon.com/t5/Wi-Fi-Bluetooth-for-Linux/Outdated-brcmfmac-firmware-for-Raspberry-Pi-4-in-OpenWrt-21-02-1/m-p/331593#M2269
Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
This switches the iwlwifi-firmware-ax200 file to API version 66, this is
the most recent version supported by our driver.
The following files used in OpenWrt changed:
amdgpu-firmware/lib/firmware/amdgpu/yellow_carp_dmcub.bin
ar3k-firmware/lib/firmware/qca/nvm_usb_00130201.bin
ar3k-firmware/lib/firmware/qca/nvm_usb_00130201_010a.bin
ar3k-firmware/lib/firmware/qca/nvm_usb_00130201_010b.bin
ar3k-firmware/lib/firmware/qca/nvm_usb_00130201_0303.bin
ar3k-firmware/lib/firmware/qca/nvm_usb_00130201_gf.bin
ar3k-firmware/lib/firmware/qca/nvm_usb_00130201_gf_010a.bin
ar3k-firmware/lib/firmware/qca/nvm_usb_00130201_gf_010b.bin
ar3k-firmware/lib/firmware/qca/nvm_usb_00130201_gf_0303.bin
ar3k-firmware/lib/firmware/qca/rampatch_usb_00130200.bin
ar3k-firmware/lib/firmware/qca/rampatch_usb_00130201.bin
iwlwifi-firmware-ax200/lib/firmware/iwlwifi-cc-a0-66.ucode
iwlwifi-firmware-ax210/lib/firmware/iwlwifi-ty-a0-gf-a0-66.ucode
iwlwifi-firmware-ax210/lib/firmware/iwlwifi-ty-a0-gf-a0.pnvm
iwlwifi-firmware-iwl9000/lib/firmware/iwlwifi-9000-pu-b0-jf-b0-46.ucode
iwlwifi-firmware-iwl9260/lib/firmware/iwlwifi-9260-th-b0-jf-b0-46.ucode
rtl8822ce-firmware/lib/firmware/rtw88/rtw8822c_fw.bin
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Debians' changelog by Henrique de Moraes Holschuh <hmh@debian.org>:
* upstream changelog: new upstream datafile 20220207
* Mitigates (*only* when loaded from UEFI firmware through the FIT)
CVE-2021-0146, INTEL-SA-00528: VT-d privilege escalation through
debug port, on Pentium, Celeron and Atom processors with signatures
0x506c9, 0x506ca, 0x506f1, 0x706a1, 0x706a8
https://github.com/intel/Intel-Linux-Processor-Microcode-Data-Files/issues/57#issuecomment-1036363145
* Mitigates CVE-2021-0127, INTEL-SA-00532: an unexpected code breakpoint
may cause a system hang, on many processors.
* Mitigates CVE-2021-0145, INTEL-SA-00561: information disclosure due
to improper sanitization of shared resources (fast-store forward
predictor), on many processors.
* Mitigates CVE-2021-33120, INTEL-SA-00589: out-of-bounds read on some
Atom Processors may allow information disclosure or denial of service
via network access.
* Fixes critical errata (functional issues) on many processors
* Adds a MSR switch to enable RAPL filtering (default off, once enabled
it can only be disabled by poweroff or reboot). Useful to protect
SGX and other threads from side-channel info leak. Improves the
mitigation for CVE-2020-8694, CVE-2020-8695, INTEL-SA-00389 on many
processors.
* Disables TSX in more processor models.
* Fixes issue with WBINDV on multi-socket (server) systems which could
cause resets and unpredictable system behavior.
* Adds a MSR switch to 10th and 11th-gen (Ice Lake, Tiger Lake, Rocket
Lake) processors, to control a fix for (hopefully rare) unpredictable
processor behavior when HyperThreading is enabled. This MSR switch
is enabled by default on *server* processors. On other processors,
it needs to be explicitly enabled by an updated UEFI/BIOS (with added
configuration logic). An updated operating system kernel might also
be able to enable it. When enabled, this fix can impact performance.
* Updated Microcodes:
sig 0x000306f2, pf_mask 0x6f, 2021-08-11, rev 0x0049, size 38912
sig 0x000306f4, pf_mask 0x80, 2021-05-24, rev 0x001a, size 23552
sig 0x000406e3, pf_mask 0xc0, 2021-04-28, rev 0x00ec, size 105472
sig 0x00050653, pf_mask 0x97, 2021-05-26, rev 0x100015c, size 34816
sig 0x00050654, pf_mask 0xb7, 2021-06-16, rev 0x2006c0a, size 43008
sig 0x00050656, pf_mask 0xbf, 2021-08-13, rev 0x400320a, size 35840
sig 0x00050657, pf_mask 0xbf, 2021-08-13, rev 0x500320a, size 36864
sig 0x0005065b, pf_mask 0xbf, 2021-06-04, rev 0x7002402, size 28672
sig 0x00050663, pf_mask 0x10, 2021-06-12, rev 0x700001c, size 28672
sig 0x00050664, pf_mask 0x10, 2021-06-12, rev 0xf00001a, size 27648
sig 0x00050665, pf_mask 0x10, 2021-09-18, rev 0xe000014, size 23552
sig 0x000506c9, pf_mask 0x03, 2021-05-10, rev 0x0046, size 17408
sig 0x000506ca, pf_mask 0x03, 2021-05-10, rev 0x0024, size 16384
sig 0x000506e3, pf_mask 0x36, 2021-04-29, rev 0x00ec, size 108544
sig 0x000506f1, pf_mask 0x01, 2021-05-10, rev 0x0036, size 11264
sig 0x000606a6, pf_mask 0x87, 2021-12-03, rev 0xd000331, size 291840
sig 0x000706a1, pf_mask 0x01, 2021-05-10, rev 0x0038, size 74752
sig 0x000706a8, pf_mask 0x01, 2021-05-10, rev 0x001c, size 75776
sig 0x000706e5, pf_mask 0x80, 2021-05-26, rev 0x00a8, size 110592
sig 0x000806a1, pf_mask 0x10, 2021-09-02, rev 0x002d, size 34816
sig 0x000806c1, pf_mask 0x80, 2021-08-06, rev 0x009a, size 109568
sig 0x000806c2, pf_mask 0xc2, 2021-07-16, rev 0x0022, size 96256
sig 0x000806d1, pf_mask 0xc2, 2021-07-16, rev 0x003c, size 101376
sig 0x000806e9, pf_mask 0x10, 2021-04-28, rev 0x00ec, size 104448
sig 0x000806e9, pf_mask 0xc0, 2021-04-28, rev 0x00ec, size 104448
sig 0x000806ea, pf_mask 0xc0, 2021-04-28, rev 0x00ec, size 103424
sig 0x000806eb, pf_mask 0xd0, 2021-04-28, rev 0x00ec, size 104448
sig 0x000806ec, pf_mask 0x94, 2021-04-28, rev 0x00ec, size 104448
sig 0x00090661, pf_mask 0x01, 2021-09-21, rev 0x0015, size 20480
sig 0x000906c0, pf_mask 0x01, 2021-08-09, rev 0x2400001f, size 20480
sig 0x000906e9, pf_mask 0x2a, 2021-04-29, rev 0x00ec, size 106496
sig 0x000906ea, pf_mask 0x22, 2021-04-28, rev 0x00ec, size 102400
sig 0x000906eb, pf_mask 0x02, 2021-04-28, rev 0x00ec, size 104448
sig 0x000906ec, pf_mask 0x22, 2021-04-28, rev 0x00ec, size 103424
sig 0x000906ed, pf_mask 0x22, 2021-04-28, rev 0x00ec, size 103424
sig 0x000a0652, pf_mask 0x20, 2021-04-28, rev 0x00ec, size 93184
sig 0x000a0653, pf_mask 0x22, 2021-04-28, rev 0x00ec, size 94208
sig 0x000a0655, pf_mask 0x22, 2021-04-28, rev 0x00ee, size 94208
sig 0x000a0660, pf_mask 0x80, 2021-04-28, rev 0x00ea, size 94208
sig 0x000a0661, pf_mask 0x80, 2021-04-29, rev 0x00ec, size 93184
sig 0x000a0671, pf_mask 0x02, 2021-08-29, rev 0x0050, size 102400
* Removed Microcodes:
sig 0x00080664, pf_mask 0x01, 2021-02-17, rev 0xb00000f, size 130048
sig 0x00080665, pf_mask 0x01, 2021-02-17, rev 0xb00000f, size 130048
* update .gitignore and debian/.gitignore.
Add some missing items from .gitignore and debian/.gitignore.
* ucode-blacklist: do not late-load 0x406e3 and 0x506e3.
When the BIOS microcode is older than revision 0x7f (and perhaps in some
other cases as well), the latest microcode updates for 0x406e3 and
0x506e3 must be applied using the early update method. Otherwise, the
system might hang. Also: there must not be any other intermediate
microcode update attempts [other than the one done by the BIOS itself],
either. It must go from the BIOS microcode update directly to the
latest microcode update.
* source: update symlinks to reflect id of the latest release, 20220207
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
e061299 wireless-regdb: Raise DFS TX power limit to 250 mW (24 dBm) for the US
2ce78ed wireless-regdb: Update regulatory rules for Croatia (HR) on 6GHz
0d39f4c wireless-regdb: Update regulatory rules for South Korea (KR)
acad231 wireless-regdb: Update regulatory rules for France (FR) on 6 and 60 GHz
ea83a82 wireless-regdb: add support for US S1G channels
4408149 wireless-regdb: add 802.11ah bands to world regulatory domain
5f3cadc wireless-regdb: Update regulatory rules for Spain (ES) on 6GHz
e0ac69b Revert "wireless-regdb: Update regulatory rules for South Korea (KR)"
40e5e80 wireless-regdb: Update regulatory rules for South Korea (KR)
e427ff2 wireless-regdb: Update regulatory rules for China (CN)
0970116 wireless-regdb: Update regulatory rules for the Netherlands (NL) on 6GHz
4dac44b wireless-regdb: update regulatory database based on preceding changes
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
ZTE MF286D is a LTE router with four gigabit ethernet ports
and integrated QMI mPCIE modem.
Hardware specification:
- CPU: IPQ4019
- RAM: 256MB
- Flash: NAND 128MB + NOR 2MB
- WLAN1: Qualcomm Atheros QCA4019 2.4GHz 802.11bgn 2x2:2
- WLAN2: Qualcomm Atheros QCA4019 5GHz 802.11anac 2x2:2
- LTE: mPCIe cat 12 card (Modem chipset MDM9250)
- LAN: 4 Gigabit Ports
- USB: 1x USB2.0 (regular port). 1x USB3.0 (mpcie - used by the modem)
- Serial console: X8 connector 115200 8n1
Known issues:
- Many LEDs are driven by the modem. Only internal LEDs and wifi LEDs
are driven by cpu.
- Wifi LED is triggered by phy0tpt only
- No VoIP support
- LAN1/WAN port is configured as WAN
- ZTE gives only one MAC per device. Use +1/+2/+3 increment for WAN
and WLAN0/1
Opening the case:
1. Take of battery lid (no battery support for this model, battery cage
is dummy).
2. Unscrew screw placed behind battery lid.
3. Take off back cover. It attached with multiple plastic clamps.
4. Unscrew four more screws hidden behind back case.
5. Remove front panel from blue chassis. There are more plastic
clamps.
6. Unscrew two boards, which secures the PCB in the chassis.
7. Extract board from blue chassis.
Console connection (X8 connector):
1. Parameters: 115200 8N1
2. Pin description: (from closest pin to X8 descriptor to farthest)
- VCC (3.3V)
- TX
- RX
- GND
Install Instructions:
Serial + initramfs:
1. Place OpenWrt initramfs image for the device on a TFTP in
the server's root. This example uses Server IP: 192.168.1.3
2. Connect serial console (115200,8n1) to X8 connector.
3. Connect TFTP server to RJ-45 port.
4. Stop in u-Boot and run u-Boot commands:
setenv serverip 192.168.1.3
setenv ipaddr 192.168.1.72
set fdt_high 0x85000000
tftp openwrt-ipq40xx-generic-zte_mf286d-initramfs-fit-zImage.itb
bootm $loadaddr
5. Please make backup of original partitions, if you think about revert
to stock.
6. Login via ssh or serial and remove stock partitions:
ubiattach -m 9
ubirmvol /dev/ubi0 -N ubi_rootfs
ubirmvol /dev/ubi0 -N ubi_rootfs_data
7. Install image via "sysupgrade -n".
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
(cosmetic changes to the commit message)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Kalle Valo ath10k-firmware repository no longer provides the
legacy board.bin files for the qca99x0 chips. Instead he
copied over the codeaurora version and add more board files.
In the future, this board-2.bin should find its way to
linux-firmware.git, which would allow us to remove the
extra download code completely.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Add the most recent supported firmware file for Intel Wi-Fi 6E AX210
wireless chip. The API version 67 is not yet supported by the driver.
Additional PNVM file is required since API version 62.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
SOC: IPQ4019
CPU: Quad-core ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d
DRAM: 256 MB
NAND: 128 MiB Macronix MX30LF1G18AC
ETH: Qualcomm Atheros QCA8075 Gigabit Switch (4x LAN, 1x WAN)
USB: 1x 3.0 (via Synopsys DesignWare DWC3 controller in the SoC)
WLAN1: Qualcomm Atheros QCA4019 2.4GHz 802.11bgn 2x2:2
WLAN2: Qualcomm Atheros QCA9984 5GHz 802.11nac 4x4:4
INPUT: 1x WPS, 1x Reset
LEDS: Status, WIFI1, WIFI2, WAN (red & blue), 4x LAN
This board is very similar to the RT-ACRH13/RT-AC58U. It must be flashed
with an intermediary initramfs image, the jffs2 ubi volume deleted, and
then finally a sysupgrade with the final image performed.
Signed-off-by: Joshua Roys <roysjosh@gmail.com>
(added ALT0)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Linux upstream commit 9370f2d05a
add load firmware file through request_firmware,this affect the
nanopi r2s and some USB adapters in kernel 5.10 with this error:
'r8152 4-1:1.0: unable to load firmware patch rtl_nic/rtl8153b-2.fw'
This patch split the USB NIC firmware files from r8169 firmware,
and adds r8152-firmware to r8152 driver.
Add kmod-usb-net-cdc-ncm to support RTL8156A and RTL8156B 2.5G ethernet
adapters supported since v5.13-rc1.
195aae321c
Signed-off-by: Marty Jones <mj8263788@gmail.com>
this patch consolidates the amd64-microcode
(moved to linux-firmware.git, previously this was an extra
debian source package download), amdgpu and radeon firmwares
into a shared "amd" makefile.
With the upcoming 20211216 linux-firmware bump,
this will include a microcode update for ZEN 3 CPUs.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The rtl8723bs firmware was removed and a symlink to the rtl8723bu
firmware was created like it is done in upstream linux-firmware.
The following OpenWrt packages are changing:
* amdgpu-firmware: Multiple updates and new files
* ar3k-firmware: Multiple updates and new files
* ath10k-firmware-qca6174: Updated ath10k/QCA6174/hw3.0/board-2.bin
* bnx2x-firmware: Added bnx2x-e1-7.13.21.0.fw, bnx2x-e1h-7.13.21.0.fw and bnx2x-e2-7.13.21.0.fw
* iwlwifi-firmware-iwl8260c: Updated iwlwifi-8000C-36.ucode
* iwlwifi-firmware-iwl8265: Updated iwlwifi-8265-36.ucode
* iwlwifi-firmware-iwl9000: Updated iwlwifi-9000-pu-b0-jf-b0-46.ucode
* iwlwifi-firmware-iwl9260: Updated iwlwifi-9260-th-b0-jf-b0-46.ucode
* r8169-firmware: Updated rtl8153c-1.fw
* rtl8723bs-firmware: removed
* rtl8723bu-firmware: Added rtlwifi/rtl8723bs_nic.bin symlink
* rtl8822ce-firmware: Updated rtw8822c_fw.bin
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Just update PKG_VERSION/PKG_MIRROR_HASH since fman-ucode
of LSDK-21.08 had no changes.
Switched to AUTORELEASE for simplicity.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
This patch adds supports for the GL-B2200 router.
Specifications:
- SOC: Qualcomm IPQ4019 ARM Quad-Core
- RAM: 512 MiB
- Flash: 16 MiB NOR - SPI0
- EMMC: 8GB EMMC
- ETH: Qualcomm QCA8075
- WLAN1: Qualcomm Atheros QCA4019 2.4GHz 802.11b/g/n 2x2
- WLAN2: Qualcomm Atheros QCA4019 5GHz 802.11n/ac W2 2x2
- WLAN3: Qualcomm Atheros QCA9886 5GHz 802.11n/ac W2 2x2
- INPUT: Reset, WPS
- LED: Power, Internet
- UART1: On board pin header near to LED (3.3V, TX, RX, GND), 3.3V without pin - 115200 8N1
- UART2: On board with BLE module
- SPI1: On board socket for Zigbee module
Update firmware instructions:
Please update the firmware via U-Boot web UI (by default at 192.168.1.1, following instructions found at
https://docs.gl-inet.com/en/3/troubleshooting/debrick/).
Normal sysupgrade, either via CLI or LuCI, is not possible from stock firmware.
Please do use the *gl-b2200-squashfs-emmc.img file, gunzipping the produced *gl-b2200-squashfs-emmc.img.gz one first.
What's working:
- WiFi 2G, 5G
- WPA2/WPA3
Not tested:
- Bluetooth LE/Zigbee
Credits goes to the original authors of this patch.
V1->V2:
- updates *arm-boot-add-dts-files.patch correctly (sorry, my mistake)
- add uboot-envtools support
V2->V3:
- Li Zhang updated official patch to fix wrong MAC address on wlan0 (PCI) interface
V3->V4:
- wire up sysupgrade
Signed-off-by: Li Zhang <li.zhang@gl-inet.com>
[fix tab and trailing space, document what's working and what's not]
Signed-off-by: TruongSinh Tran-Nguyen <i@truongsinh.pro>
[rebase on top of master, address remaining comments]
Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
[remove redundant check in platform.sh]
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This patch adds support for the Teltonika RUTX10.
This device is an industrial DIN-rail router with 4 ethernet ports,
2.4G/5G dualband WiFi, Bluetooth, a USB 2.0 port and two GPIOs.
The RUTX series devices are very similiar so common parts of the DTS
are kept in a DTSI file. They are based on the QCA AP-DK01.1-C1 dev
board.
See https://teltonika-networks.com/product/rutx10 for more info.
Hardware:
SoC: Qualcomm IPQ4018
RAM: 256MB DDR3
SPI Flash 1: XTX XT25F128B (16MB, NOR)
SPI Flash 2: XTX XT26G02AWS (256MB, NAND)
Ethernet: Built-in IPQ4018 (SoC, QCA8075), 4x 10/100/1000 ports
WiFi 1: Qualcomm QCA4019 IEEE 802.11b/g/n
Wifi 2: Qualcomm QCA4019 IEEE 802.11a/n/ac
USB Hub: Genesys Logic GL852GT
Bluetooth: Qualcomm CSR8510 (A10U)
LED/GPIO controller: STM32F030 with custom firmware
Buttons: Reset button
Leds: Power (green, cannot be controlled)
WiFi 2.4G activity (green)
WiFi 5G activity (green)
MACs Details verified with the stock firmware:
eth0: Partition 0:CONFIG Offset: 0x0
eth1: = eth0 + 1
radio0 (2.4 GHz): = eth0 + 2
radio1 (5.0 GHz): = eth0 + 3
Label MAC address is from eth0.
The LED/GPIO controller needs a separate kernel driver to function.
The driver was extracted from the Teltonika GPL sources and can be
found at following feed: https://github.com/0xFelix/teltonika-rutx-openwrt
USB detection of the bluetooth interface is sometimes a bit flaky. When
not detected power cycle the device. When the bluetooth interface was
detected properly it can be used with bluez / bluetoothctl.
Flash instructions via stock web interface (sysupgrade based):
1. Set PC to fixed ip address 192.168.1.100
2. Push reset button and power on the device
3. Open u-boot HTTP recovery at http://192.168.1.1
4. Upload latest stock firmware and wait until the device is rebooted
5. Open stock web interface at http://192.168.1.1
6. Set some password so the web interface is happy
7. Go to firmware upgrade settings
8. Choose
openwrt-ipq40xx-generic-teltonika_rutx10-squashfs-nand-factory.ubi
9. Set 'Keep settings' to off
10. Click update, when warned that it is not a signed image proceed
Return to stock firmware:
1. Set PC to fixed ip address 192.168.1.100
2. Push reset button and power on the device
3. Open u-boot HTTP recovery at http://192.168.1.1
4. Upload latest stock firmware and wait until the device is rebooted
Note: The DTS expects OpenWrt to be running from the second rootfs
partition. u-boot on these devices hot-patches the DTS so running from the
first rootfs partition should also be possible. If you want to be save follow
the instructions above. u-boot HTTP recovery restores the device so that when
flashing OpenWrt from stock firmware it is flashed to the second rootfs
partition and the DTS matches.
Signed-off-by: Felix Matouschek <felix@matouschek.org>
This adds support for the MikroTik RouterBOARD RBD53iG-5HacD2HnD
(hAP ac³), a indoor dual band, dual-radio 802.11ac
wireless AP with external omnidirectional antennae, USB port, five
10/100/1000 Mbps Ethernet ports and PoE passthrough.
See https://mikrotik.com/product/hap_ac3 for more info.
Specifications:
- SoC: Qualcomm Atheros IPQ4019
- RAM: 256 MB
- Storage: 16 MB NOR + 128 MB NAND
- Wireless:
· Built-in IPQ4019 (SoC) 802.11b/g/n 2x2:2, 3 dBi antennae
· Built-in IPQ4019 (SoC) 802.11a/n/ac 2x2:2, 5.5 dBi antennae
- Ethernet: Built-in IPQ4019 (SoC, QCA8075) , 5x 1000/100/10 port,
passive PoE in, PoE passtrough on port 5
- 1x USB Type A port
Installation:
1. Boot the initramfs image via TFTP
2. Run "cat /proc/mtd" and look for "ubi" partition mtd device number, ex. "mtd1"
3. Use ubiformat to remove MikroTik specific UBI volumes
* Detach the UBI partition by running: "ubidetach -d 0"
* Format the partition by running: "ubiformat /dev/mtdN -y"
Replace mtdN with the correct mtd index from step 2.
3. Flash the sysupgrade image using "sysupgrade -n"
Signed-off-by: Robert Marko <robimarko@gmail.com>
Tested-by: Mark Birss <markbirss@gmail.com>
Tested-by: Michael Büchler <michael.buechler@posteo.net>
Tested-by: Alex Tomkins <tomkins@darkzone.net>
P&W R619AC is a IPQ4019 Dual-Band AC1200 router.
It is made by P&W (p2w-tech.com) known as P&W R619AC
but marketed and sold more popularly as G-DOCK 2.0.
Specification:
* SOC: Qualcomm Atheros IPQ4019 (717 MHz)
* RAM: 512 MiB
* Flash: 16 MiB (NOR) + 128 MiB (NAND)
* Ethernet: 5 x 10/100/1000 (4 x LAN, 1 x WAN)
* Wireless:
- 2.4 GHz b/g/n Qualcomm Atheros IPQ4019
- 5 GHz a/n/ac Qualcomm Atheros IPQ4019
* USB: 1 x USB 3.0
* LED: 4 x LAN, 1 x WAN, 2 x WiFi, 1 x Power (All Blue LED)
* Input: 1 x reset
* 1 x MicroSD card slot
* Serial console: 115200bps, pinheader J2 on PCB
* Power: DC 12V 2A
* 1 x Unpopulated mPCIe Slot (see below how to connect it)
* 1 x Unpopulated Sim Card Slot
Installation:
1. Access to tty console via UART serial
2. Enter failsafe mode and mount rootfs
<https://openwrt.org/docs/guide-user/troubleshooting/failsafe_and_factory_reset>
3. Edit inittab to enable shell on tty console
`sed -i 's/#ttyM/ttyM/' /etc/inittab`
4. Reboot and upload `-nand-factory.bin` to the router (using wget)
5. Use `sysupgrade` command to install
Another installation method is to hijack the upgrade server domain
of stock firmware, because it's using insecure http.
This commit is based on @LGA1150(at GitHub)'s work
<a4932c8d5a>
With some changes:
1. Added `qpic_bam` node in dts. I don't know much about this,
but I observed other dtses have this node.
2. Removed `ldo` node under `sd_0_pinmux`, because `ldo` cause SD card not
working. This fix is from
<51143b4c75>
3. Removed the 32MB NOR variant.
4. Removed `cd-gpios` in `sdhci` node, because it's reported that it makes
wlan2g led light up.
5. Added ethphy led config in dts.
6. Changed nand partition label from `rootfs` to `ubi`.
About the 128MiB variant: The stock bootloader sets size of nand to 64MiB.
But most of this devices have 128MiB nand. If you want to use all 128MiB,
you need to modify the `MIBIB` data of bootloader. More details can be
found on github:
<https://github.com/openwrt/openwrt/pull/3691#issuecomment-818770060>
For instructions on how to flash the MIBIB partition from u-boot console:
<https://github.com/openwrt/openwrt/pull/3691#issuecomment-819138232>
About the Mini PCIe slot: (from "ygleg")
"The REFCLK signals on the Mini PCIe slot is not connected on
this board out of the box. If you want to use the Mini PCIe slot
on the board, you need to (preferably) solder two 0402 resistors:
R436 (REFCLK+) and R444 (REFCLK-)..."
This and much more information is provoided in the github comment:
<https://github.com/openwrt/openwrt/pull/3691#issuecomment-968054670>
Signed-off-by: Richard Yu <yurichard3839@gmail.com>
Signed-off-by: DENG Qingfang <dqfext@gmail.com>
[Added comment about MIBIB+128 MiB variant. Added commit
message section about pcie slot. Renamed gpio-leds' subnodes
and added color, function+enum properties.]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Back in the day, the board-2.bin came with ath10k-firmware-qca4019.
This changed with
commit c3b2efaf24 ("linux-firmware: ath10k: add board firmware packages")
which placed the board-2.bin into a separate package: ath10k-board-qca4019.
This was great, because it addressed one of the caveat of the original
ipq-wifi package:
commit fa03d441e9 ("firmware: add custom IPQ wifi board definitions")
| 2. updating ath10k-firmware-qca4019 will also replace
| the board-2.bin. For this cases the user needs to
| manually reinstall the wifi-board package once the
| ath10k-firmware-qca4019 is updated.
This could be extended further so that ipq-wifi packages
no longer use "install-override" and the various QCA4019
variants list the ath10k-board-qca4019 as a CONFLICT
package.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
e983a25 Update regulatory rules for Ecuador (EC)
a0bcb88 wireless-regdb: Update regulatory rules for Norway (NO) on 6 and 60 GHz
cdf854d wireless-regdb: Update regulatory rules for Germany (DE) on 6GHz
86cba52 wireless-regdb: reduce bandwidth for 5730-5850 and 5850-5895 MHz in US
6fa2384 wireless-regdb: remove PTMP-ONLY from 5850-5895 MHz for US
9839e1e wireless-regdb: recent FCC report and order allows 5850-5895 immediately
42dfaf4 wireless-regdb: update 5725-5850 MHz rule for GB
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The official Plasma Cloud firmware adjusted the BDFs to contain new
conformance test limits and target power values. These should be imported
to avoid emissions outside the allowed limits.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
The ipq-wifi-netgear_wac510 package is not selected by any device and would
be empty anyway. The default board-2.bin from ath10k-board-qca4019 is
therefore used for this device and the package doesn't provide any visible
features.
Fixes: b126d9c3a3 ("ipq40xx: add netgear wac510 support")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Some devices (such as Extreme Networks WS-AP3959i-ROW) do not contain
precal binaries in ART, and the precal in the cards eeprom causes
firmware load errors.
These firmware files were previously in linux-firmware,
so these are adding them back and renaming to be cleaner.
Signed-off-by: Damien Mascord <tusker@tusker.org>
In there linux-firmware repository located in kernel, there were removed old
broadcom firmware [1] as they seem to be likely vulnerable to KrØØk vulnerability
(CVE-2019-15126), because Cypress released new versions and superseded
by it.
In OpenWrt, there is Makefile for cypress-firmware, which already provides
the same named packages like it was in linux-firmware. For example, cypress-firmware-43455-sdio
provides brcmfmac-firmware-43455-sdio [2].
Changelog between 2020118 and 20210315:
3568f96 (tag: 20210315) linux-firmware: Update firmware file for Intel Bluetooth AX210
9e96e50 linux-firmware: Update firmware file for Intel Bluetooth AX200
c8d0db5 linux-firmware: Update firmware file for Intel Bluetooth AX201
5e2a387 Merge tag 'iwlwifi-fw-2021-03-05-v3' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/linux-firmware into main
b0d3e31 rtw88: 8822c: Update normal firmware to v9.9.6
5a2fd63 iwlwifi: add new FWs from core59-66 release
4f54906 iwlwifi: update 9000-family firmwares
11b7607 iwlwifi: update 7265D firmware
e425f76 Merge branch 'add-silabs-wf200' of github.com:jerome-pouiller/linux-firmware into main
5ecd13f Mellanox: Add new mlxsw_spectrum firmware xx.2008.2406
58fb90a linux-firmware: add frimware for mediatek bluetooth chip (MT7921)
e576a1b rtw89: 8852a: add firmware v0.9.12.2
048a7cb WHENCE: add missing symlink for BananaPi M3
aa6c6e7 Add symlink for BananaPi M2 to brcmfmac43430-sdio config
58825f7 brcm: Fix Raspberry Pi 4B NVRAM file
520f71b silabs: add new firmware for WF200
f7915a0 amdgpu: add initial firmware for green sardine
80cb579 rtw88: RTL8822C: Update normal firmware to v9.9.5
b79d239 (tag: 20210208) Merge branch 'DG1-guc-huc-ADLS-dmc' of git://anongit.freedesktop.org/drm/drm-firmware into main
66970e1 Merge branch 'qcom-rb5' of https://github.com/lumag/linux-firmware into main
cf6fc2b Mellanox: Add new mlxsw_spectrum firmware xx.2008.2304
391fd50 linux-firmware: add firmware for MT7921
c5e3240 rtw88: RTL8821C: Update firmware to v24.8
d33d2d8 linux-firmware: Update firmware file for Intel Bluetooth AX210
3027ae4 linux-firmware: Update firmware file for Intel Bluetooth AX200
13979c3 linux-firmware: Update firmware file for Intel Bluetooth AX201
348d8a9 i915: Add DMC v2.01 for ADL-S
f33f1f7 i915: Add HuC v7.7.1 for DG1
6a422f5 i915: Add GuC v49.0.1 for DG1
df822a8 qcom: Add venus firmware files for VPU-1.0
11a1db1 qcom: Add SM8250 Compute DSP firmware
e55248b qcom: Add SM8250 Audio DSP firmware
da74cc6 qcom: add firmware files for Adreno a650
0578970 brcm: Link RPi4's WiFi firmware with DMI machine name.
d528862 brcm: Add NVRAM for Vamrs 96boards Rock960
870b805 brcm: Update Raspberry Pi 3B+/4B NVRAM for downstream changes
a28a590 cypress: Fix link direction
060ad8b cypress: Link the new cypress firmware to the old brcm files
0f0aefd brcm: remove old brcm firmwares that have newer cypress variants
f580dc2 rtl_bt: Update RTL8822C BT(UART I/F) FW to 0x059A_25CB
7df2220 rtl_bt: Update RTL8822C BT(USB I/F) FW to 0x099a_7253
e79405d rtl_bt: Add firmware and config files for RTL8852A BT USB chip
ef3813d rtl_bt: Update RTL8821C BT(USB I/F) FW to 0x829a_7644
646f159 (tag: 20201218) make AP6212 in bananpi m2 plus/zero work
28185ec linux-firmware: Update firmware file for Intel Bluetooth AX210
23da869 linux-firmware: Update firmware file for Intel Bluetooth AX200
2099248 linux-firmware: Update firmware file for Intel Bluetooth AX201
94de5e2 linux-firmware: Update firmware file for Intel Bluetooth 9560
27a3689 linux-firmware: Update firmware file for Intel Bluetooth 9260
5c3c4af Merge branch 'lt9611uxc' of https://github.com/lumag/linux-firmware into main
aaed4a8 Merge branch 'v1.1.6' of https://github.com/irui-wang/linux_fw_vpu_v1.1.6 into main
d8c9865 Merge branch 'master' of https://github.com/sampnimm/linux-firmware-BT into main
63ab3db linux-firmware: add firmware for Lontium LT9611UXC DSI to HDMI bridge
0fe0fe0 mediatek: update MT8173 VPU firmware to v1.1.6
1a08ec9 QCA : Updated firmware files for WCN3991
7455a36 Merge branch 'guc_v49' of git://anongit.freedesktop.org/drm/drm-firmware into main
7eb7fda linux-firmware: Update firmware file for Intel Bluetooth AX210
5cbf459 linux-firmware: Update firmware file for Intel Bluetooth AX210
c487f7d i915: Add GuC firmware v49.0.1 for all platforms
d9ffb07 i915: Remove duplicate KBL DMC entry
b362fd4 Mellanox: Add new mlxsw_spectrum firmware xx.2008.2018
bc9cd0b linux-firmware: Update AMD SEV firmware
54c797a amdgpu: add sienna cichlid firmware for 20.45
1340e9c amdgpu: update vega20 firmware for 20.45
b260c9c amdgpu: update vega12 firmware for 20.45
d683bd5 amdgpu: update vega10 firmware for 20.45
7c81cc2 amdgpu: update renoir firmware for 20.45
3619e57 amdgpu: update navi14 firmware for 20.45
68ce0fb amdgpu: update navi12 firmware for 20.45
e889b80 amdgpu: update navi10 firmware for 20.45
f4edc15 amdgpu: update raven2 firmware for 20.45
e71210f amdgpu: update raven firmware for 20.45
[1] https://git.kernel.org/pub/scm/linux/kernel/git/firmware/linux-firmware.git/commit/?id=0f0aefd733f70beae4c0246edbd2c158d5ce974c
[2] eeda8652f1/package/firmware/cypress-firmware/Makefile (L124)
Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
This adds support for the Netgear WAC510 Insight Managed Smart Cloud
Wireless Access Point, an indoor dual-band, dual-radio 802.11ac
business-class wireless AP with integrated omnidirectional antennae
and two 10/100/1000 Mbps Ethernet ports.
For more information see:
<https://www.netgear.com/business/wifi/access-points/wac510>
Specifications:
SoC: Qualcomm IPQ4018 (DAKOTA) ARM Quad-Core
RAM: 256 MiB
Flash1: 2 MiB Winbond W25Q16JV SPI-NOR
Flash2: 128 MiB Winbond W25N01GVZEIG SPI-NAND
Ethernet: Built-in IPQ4018 (SoC, QCA8072 PHY), 2x 1000/100/10 port,
WAN port active IEEE 802.3af/at PoE in
Wireless1: Built-in IPQ4018 (SoC) 802.11b/g/n 2x2:2, 3 dBi antennae
Wireless2: Built-in IPQ4018 (SoC) 802.11a/n/ac 2x2:2, 4 dBi antennae
Input: (Optional) Barrel 12 V 2.5 A Power, Reset button SW1
LEDs: Power, Insight, WAN PoE, LAN, 2.4G WLAN, 5G WLAN
Serial: Header J2
1 - 3.3 Volt (Do NOT connect!)
2 - TX
3 - RX
4 - Ground
WARNING: The serial port needs a TTL/RS-232 3.3 volt level converter!
The Serial settings are 115200-8-N-1.
Installation via Stock Web Interface:
BTW: The default factory console/web interface login user/password are
admin/password.
In the web interface navigating to Management - Maintenance - Upgrade -
'Firmware Upgrade' will show you what is currently installed e.g.:
Manage Firmware
Current Firmware Version: V5.0.10.2
Backup Firmware Version: V1.2.5.11
Under 'Upgrade Options' choose Local (alternatively SFTP would be
available) then click/select 'Browse File' on the right side, choose
openwrt-ipq40xx-generic-netgear_wac510-squashfs-nand-factory.tar
and hit the Upgrade button below. After a minute or two your browser
should indicate completion printing 'Firmware update complete.' and
'Rebooting AP...'.
Note that OpenWrt will use the WAN PoE port as actual WAN port
defaulting to DHCP client but NOT allowing LuCI access, use LAN port
defaulting to 192.168.1.1/24 to access LuCI.
Installation via TFTP Requiring Serial U-Boot Access:
Connect to the device's serial port and hit any key to stop autoboot.
Upload and boot the initramfs based OpenWrt image as follows:
(IPQ40xx) # setenv serverip 192.168.1.1
(IPQ40xx) # setenv ipaddr 192.168.1.2
(IPQ40xx) # tftpboot openwrt-ipq40xx-generic-netgear_wac510-initramfs-fit-uImage.itb
(IPQ40xx) # bootm
Note: This only runs OpenWrt from RAM and has not installed anything
to flash as of yet. One may permanently install OpenWrt as follows:
Check the MTD device number of the active partition:
root@OpenWrt:/# dmesg | grep 'set to be root filesystem'
[ 1.010084] mtd: device 9 (rootfs) set to be root filesystem
Upload the factory image ending with .ubi to /tmp (e.g. using scp or
tftp). Then flash the image as follows (substituting the 9 in mtd9
below with whatever number reported above):
root@OpenWrt:/# ubiformat /dev/mtd9 -f /tmp/openwrt-ipq40xx-generic-netgear_wac510-squashfs-nand-factory.ubi
And reboot.
Dual Image Configuration:
The default U-Boot boot command bootipq uses the U-Boot environment
variables primary/secondary to decide which image to boot. E.g.
primary=0, secondary=3800000 uses rootfs while primary=3800000,
secondary=0 uses rootfs_1.
Switching their values changes the active partition. E.g. from within
U-Boot:
(IPQ40xx) # setenv primary 0
(IPQ40xx) # setenv secondary 3800000
(IPQ40xx) # saveenv
Or from a OpenWrt userspace serial/SSH console:
fw_setenv primary 0
fw_setenv secondary 3800000
Note that if you install two copies of OpenWrt then each will have its
independent configuration not like when switching partitions on the
stock firmware.
BTW: The kernel log shows which boot partition is active:
[ 2.439050] ubi0: attached mtd9 (name "rootfs", size 56 MiB)
vs.
[ 2.978785] ubi0: attached mtd10 (name "rootfs_1", size 56 MiB)
Note: After 3 failed boot attempts it automatically switches partition.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
[squashed netgear-tar commit into main and rename netgear-tar for
now, until it is made generic.]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This marks all packages which depend on a target with @TARGET nonshared.
If they are not marked nonshared they would be build by the SDK build
and if this happens with a different SDK, then the SDK from the target
the package depends on, the package would not be added to the index.
This should fix the image builder for some of these packages.
This should fix the image builder at least for bcm27xx/bcm2710 and
bcm4908/generic.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This commit adds support for the MikroTik SXTsq 5 ac (RBSXTsqG-5acD),
an outdoor 802.11ac wireless CPE with one 10/100/1000 Mbps Ethernet
port.
Specifications:
- SoC: Qualcomm Atheros IPQ4018
- RAM: 256 MB
- Storage: 16 MB NOR
- Wireless: IPQ4018 (SoC) 802.11a/n/ac 2x2:2, 16 dBi antennae
- Ethernet: IPQ4018 (SoC) 1x 10/100/1000 port, 10-28 Vdc PoE in
- 1x Ethernet LED (green)
- 7x user-controllable LEDs
· 1x power (blue)
· 1x user (green)
· 5x rssi (green)
Note:
Serial UART is probably available on the board, but it has not been
tested.
Flashing:
Boot via TFTP the initramfs image. Then, upload a sysupgrade image
via SSH and flash it normally. More info at the "Common procedures
for MikroTik products" page https://openwrt.org/toh/mikrotik/common.
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
Add firmware and board file for Qualcomm Atheros QCA9377 802.11ac Wireless
Network Adapter (rev 31) recognized as [168c:0042].
This card supports standard 1x1 802.11ac Wave2, BT5, and MU-MIMO.
Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
This adds support for the MikroTik RouterBOARD RBD52G-5HacD2HnD-TC
(hAP ac²), a indoor dual band, dual-radio 802.11ac
wireless AP with integrated omnidirectional antennae, USB port and five
10/100/1000 Mbps Ethernet ports.
See https://mikrotik.com/product/hap_ac2 for more info.
Specifications:
- SoC: Qualcomm Atheros IPQ4018
- RAM: 128 MB
- Storage: 16 MB NOR
- Wireless:
· Built-in IPQ4018 (SoC) 802.11b/g/n 2x2:2, 2.5 dBi antennae
· Built-in IPQ4018 (SoC) 802.11a/n/ac 2x2:2, 2.5 dBi antennae
- Ethernet: Built-in IPQ4018 (SoC, QCA8075) , 5x 1000/100/10 port,
passive PoE in
- 1x USB Type A port
Installation:
Boot the initramfs image via TFTP and then flash the sysupgrade
image using "sysupgrade -n"
Signed-off-by: Robert Marko <robimarko@gmail.com>
The ls-ddr-phy package needs fiptool options that are not
available via the version from arm-trusted-firmware-tools.
This breaks build for layerscape with the recently added LX2160a:
create: unrecognized option '--ddr-immem-udimm-1d'
Use the tfa-layerscape variant again for now, but rename it to
fiptool-layerscape to indicate that it's a specific variant.
This reverts 84bc7d31e0 ("tfa-layerscape: don't build fiptool").
Fixes: f59d7aab2a ("layerscape: add ddr-phy package")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The QorIQ LX2160A reference design board provides a comprehensive platform
that enables design and evaluation of the LX2160A processor.
- Enables network intelligence with the next generation Datapath (DPPA2)
which provides differentiated offload and a rich set of IO, including
10GE, 25GE, 40GE, and PCIe Gen4
- Delivers unprecedented efficiency and new virtualized networks
- Supports designs in 5G packet processing, network function
virtualization, storage controller, white box switching, network
interface cards, and mobile edge computing
- Supports all three LX2 family members (16-core LX2160A; 12-core LX2120A;
and 8-core LX2080A)
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
[use AUTORELEASE, add dtb to firmware part]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Add ddr-phy package for layerscape. Currently only LX2160ARDB
requires the package.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
[use AUTORELEASE]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The LS1046A Freeway board (FRWY) is a high-performance computing,
evaluation, and development platform that supports the QorIQ
LS1046A architecture processor capable of support more than 32,000
CoreMark performance. The FRWY-LS1046A board supports the QorIQ
LS1046A processor, onboard DDR4 memory, multiple Gigabit Ethernet,
USB3.0 and M2_Type_E interfaces for Wi-Fi.
The FRWY-LS1046A-TP includes the Coral Tensor Flow Processing Unit
that offloads AI/ML inferencing from the CPU to provide significant
boost for AI/ML applications. The FRWY-LS1046A-TP includes one M.2
TPU module and more modules can easily be added including USB
versions of the module to scale the AI/ML performance.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
[rebase, use AUTORELEASE, fix sorting, add dtb to firmware part]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Multiple sources are hosted on OpenWrts source server only. The source
URLs to point to the server vary based on different epochs in OpenWrts
history.
Replace all by @OPENWRT which is an "empty" mirror, therefore using the
fallback servers sources.cdn.openwrt.org and sources.openwrt.org.
Signed-off-by: Paul Spooren <mail@aparcar.org>
This patch adds wil6210 firmware and board files.
Firmware version is not up to date but is only freely redistributable one I found.
Board file is a generic one so most devices and especially those for long distance
PtP links will require so in a ipq-wifi like way.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Specifications:
SOC: Qualcomm IPQ4018 (DAKOTA) ARM Quad-Core
RAM: 256 MiB
FLASH1: 4 MiB NOR
FLASH2: 128 MiB NAND
ETH: Qualcomm QCA8075
WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11b/g/n 2x2
WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11n/ac W2 2x2
INPUT: Reset
LED: Power, Internet
UART1: On board pin header near to LED (3.3V, TX, RX, GND), 3.3V without pin - 115200 8N1
OTHER: On board with BLE module - by cp210x USB serial chip
On board hareware watchdog with GPIO0 high to turn on, and GPIO4 for watchdog feed
Install via uboot tftp or uboot web failsafe.
By uboot tftp:
(IPQ40xx) # tftpboot 0x84000000 openwrt-ipq40xx-generic-glinet_gl-ap1300-squashfs-nand-factory.ubi
(IPQ40xx) # run lf
By uboot web failsafe:
Push the reset button for 10 seconds util the power led flash faster,
then use broswer to access http://192.168.1.1
Afterwards upgrade can use sysupgrade image.
Signed-off-by: Dongming Han <handongming@gl-inet.com>
The Makefile is rejecting all files with for a given prefix (here
"board-plasmacloud_pa2200") when it didn't match a known suffix. Instead it
stops the build with an error like:
Makefile:135: *** Unrecognized board-file suffix '.ipq4019' for 'board-plasmacloud_pa2200.ipq4019'. Stop.
The correct suffix for the QCA4019/hw1.0 is qca4019 and not ipq4019.
Fixes: 4871fd2616 ("ipq40xx: add support for Plasma Cloud PA2200")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
The Makefile is rejecting all files with for a given prefix (here
"board-plasmacloud_pa1200") when it didn't match a known suffix. Instead it
stops the build with an error like:
Makefile:135: *** Unrecognized board-file suffix '.ipq4019' for 'board-plasmacloud_pa1200.ipq4019'. Stop.
The correct suffix for the QCA4019/hw1.0 is qca4019 and not ipq4019.
Fixes: ea5bb6bbfe ("ipq40xx: add support for Plasma Cloud PA1200")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
SOC: IPQ4018 / QCA Dakota
CPU: Quad-Core ARMv7 Processor rev 5 (v71) Cortex-A7
DRAM: 256 MiB
NOR: 32 MiB
ETH: Qualcomm Atheros QCA8075 (2 ports)
PLC: MaxLinear G.hn 88LX5152
WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2
WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2
INPUT: RESET, WiFi, PLC Button
LEDS: red/white home, white WiFi
To modify a retail device to run OpenWRT firmware:
1) Setup a TFTP server on IP address 192.168.0.100 and copy the OpenWRT
initramfs (initramfs-fit-uImage.itb) to the TFTP root as 'uploadfile'.
2) Power on the device while pressing the recessed reset button next to
the Ethernet ports. This causes the bootloader to retrieve and start
the initramfs.
3) Once the initramfs is booted, the device will come up with IP
192.168.1.1. You can then connect through SSH (allow some time for
the first connection).
4) On the device shell, run 'fw_printenv' to show the U-boot environment.
Backup this information since it contains device unique factory data.
5) Change the boot command to support booting OpenWRT:
# fw_setenv bootcmd 'sf probe && sf read 0x84000000 0x180000 0x400000 && bootm'
6) Change directory to /tmp, download the sysupgrade (e.g. through wget)
and install it with sysupgrade. The device will reboot into OpenWRT.
Notice that there is currently no support for booting the G.hn chip.
This requires userland software we lack the rights to share right now.
Signed-off-by: Stefan Schake <stefan.schake@devolo.de>
Device specifications:
* QCA IPQ4019
* 256 MB of RAM
* 32 MB of SPI NOR flash (w25q256)
- 2x 15 MB available; but one of the 15 MB regions is the recovery image
* 2T2R 2.4 GHz
- QCA4019 hw1.0 (SoC)
- requires special BDF in QCA4019/hw1.0/board-2.bin with
bus=ahb,bmi-chip-id=0,bmi-board-id=20,variant=PlasmaCloud-PA2200
* 2T2R 5 GHz (channel 36-64)
- QCA9888 hw2.0 (PCI)
- requires special BDF in QCA9888/hw2.0/board-2.bin
bus=pci,bmi-chip-id=0,bmi-board-id=16,variant=PlasmaCloud-PA2200
* 2T2R 5 GHz (channel 100-165)
- QCA4019 hw1.0 (SoC)
- requires special BDF in QCA4019/hw1.0/board-2.bin with
bus=ahb,bmi-chip-id=0,bmi-board-id=21,variant=PlasmaCloud-PA2200
* GPIO-LEDs for 2.4GHz, 5GHz-SoC and 5GHz-PCIE
* GPIO-LEDs for power (orange) and status (blue)
* 1x GPIO-button (reset)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x gigabit ethernet
- phy@mdio3:
+ Label: Ethernet 1
+ gmac0 (ethaddr) in original firmware
+ used as LAN interface
- phy@mdio4:
+ Label: Ethernet 2
+ gmac1 (eth1addr) in original firmware
+ 802.3at POE+
+ used as WAN interface
* 12V 2A DC
Flashing instructions:
The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the factory image to the u-boot when the device boots up.
Signed-off-by: Marek Lindner <marek.lindner@kaiwoo.ai>
[sven@narfation.org: prepare commit message, rebase, use all LEDs, switch
to dualboot_datachk upgrade script, use eth1 as designated WAN interface]
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Device specifications:
* QCA IPQ4018
* 256 MB of RAM
* 32 MB of SPI NOR flash (w25q256)
- 2x 15 MB available; but one of the 15 MB regions is the recovery image
* 2T2R 2.4 GHz
- QCA4019 hw1.0 (SoC)
- requires special BDF in QCA4019/hw1.0/board-2.bin with
bus=ahb,bmi-chip-id=0,bmi-board-id=16,variant=PlasmaCloud-PA1200
* 2T2R 5 GHz
- QCA4019 hw1.0 (SoC)
- requires special BDF in QCA4019/hw1.0/board-2.bin with
bus=ahb,bmi-chip-id=0,bmi-board-id=17,variant=PlasmaCloud-PA1200
* 3x GPIO-LEDs for status (cyan, purple, yellow)
* 1x GPIO-button (reset)
* 1x USB (xHCI)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x gigabit ethernet
- phy@mdio4:
+ Label: Ethernet 1
+ gmac0 (ethaddr) in original firmware
+ used as LAN interface
- phy@mdio3:
+ Label: Ethernet 2
+ gmac1 (eth1addr) in original firmware
+ 802.3af/at POE(+)
+ used as WAN interface
* 12V/24V 1A DC
Flashing instructions:
The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the factory image to the u-boot when the device boots up.
Signed-off-by: Marek Lindner <marek.lindner@kaiwoo.ai>
[sven@narfation.org: prepare commit message, rebase, use all LEDs, switch
to dualboot_datachk upgrade script, use eth1 as designated WAN interface]
Signed-off-by: Sven Eckelmann <sven@narfation.org>
All firmwares were added to linux-firmware, so there's no need to keep this
package definitions.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Instead of duplicating board firmware binaries, which are exactly the same
as the ones from linux-firmware, add dependencies and remove duplicated
downloads.
Runtime-tested on ath79 (TP-Link Archer C7 v2) and ipq806x (Netgear R7800).
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Split ath10k firmwares into board and firmware packages.
This way we can add dependencies to ath10k-ct firmware packages.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
