Commit Graph

22628 Commits

Author SHA1 Message Date
Pawel Dembicki
aff965a415 generic: backport Wistron Neweb D19Q1 patches
Backport patches which adds suport for the Wistron Neweb D19Q1 3G/4G modem,
used in D-Link DWR-960.

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2020-04-08 13:57:50 +01:00
Adrian Schmutzler
f761f4052c ramips: mt7621: harmonize naming scheme for Mikrotik
So far, image/device/board names for Mikrotik devices in mt7621 have
been used quite inconsistently.

This patch harmonizes the naming scheme by applying the same style
as used lately in ath79, i.e. using "RouterBOARD" as separate word
in the model name (instead of RB prefix for the number) and deriving
the board/device name from that (= make lower case and replace spaces
by hyphens).

This style has already been used for most the model/DEVICE_MODEL
variables in mt7621, so this is essentially just adjusting the remaining
variables to that.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-04-08 13:46:30 +02:00
Tobias Schramm
48b4aab80c ramips: mt7621: reenable rbm11g
I have a rbm11g and can confirm that the LAN port is indeed
switch port 0.

Signed-off-by: Tobias Schramm <t.schramm@manjaro.org>
2020-04-08 13:42:58 +02:00
Tobias Schramm
57f4eab677 ramips: mt7621: add label mac address to rbm11g
The rbm11g has a label with printed on mac address similar to the
rbm33g.

Signed-off-by: Tobias Schramm <t.schramm@manjaro.org>
2020-04-08 13:42:09 +02:00
INAGAKI Hiroshi
e8787291b3 ramips: add support for Buffalo WSR-2533DHPL
Buffalo WSR-2533DHPL is a 2.4/5 GHz band 11ac router, based on MediaTek
MT7621A.

Specification:

- SoC		: MediaTek MT7621A
- RAM		: DDR3 128 MiB
- Flash		: SPI-NOR 16 MiB
- WLAN		: 2.4/5 GHz 4T4R (2x MediaTek MT7615N)
- Ethernet	: 10/100/1000 Mbps
  - Switch	: MediaTek MT7530 (SoC)
- LED/keys	: 8x/6x (3x buttons, 2x slide-switches)
- UART		: through-hole on PCB
  - J4: 3.3V, GND, TX, RX from triangle-mark
  - 57600n8
- Power		: 12VDC 1.5A

Flash instruction using initramfs image:

1. prepare the TFTP server with the initramfs image renamed to
   "linux.trx-recovery" and IP address "192.168.11.2"
2. press the "AOSS" button while powering on the WSR-2533DHPL
3. after 10 seconds, release the "AOSS" button, WSR-2533DHPL downloads
   the initramfs image and boot with it automatically
4. on the initramfs image, download the sysupgrade image to the device
   and perform sysupgrade with it
5. wait ~120 seconds to complete flashing

Switch position overview:

- slide-switch1 (2x positions)
  - "AUTO"
  - "MANUAL" (not connected to gpio)

- slide-switch2 (3x positions)
  - "ROUTER"
  - "AP" (not connected to gpio)
  - "WB"

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
[add note on switches, fix group->groups for state_default]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-04-07 17:04:18 +02:00
Dan Haab
c459a6bf48 bcm53xx: add support for Luxul FullMAC WiFi devices
This prepares support for models XAP-1610 and XWR-3150. Flashing
requires using Luxul firmware version:
1) 8.1.0 or newer for XAP-1610
2) 6.4.0 or newer for XWR-3150
and uploading firmware using "Firmware Update" web UI page.

Signed-off-by: Dan Haab <dan.haab@legrand.com>
2020-04-07 15:27:52 +02:00
Chris Morgan
7daab62861 ath79: add support for Comfast CF-EW72
Specifications:
Qualcomm/Atheros QCA9531 + QCA9886
2x 10/100 Mbps Ethernet, with 48v PoE
2T2R 2.4 GHz, 802.11b/g/n
2T2R 5 GHz, 802.11a/n/ac
128MB RAM
16MB SPI Flash
4x LED (Always On Power, LAN, WAN, WLAN)

Flashing Instructions:
Original firmware is based on OpenWRT, so flashing the sysupgrade image on
the factory firmware is sufficient.

Tested: Reset button, WAN LED, LAN LED, Power LED (always on, not much
to test), WLAN LED (one LED only for 2 interfaces, by default it gets
assigned to the first interface), MAC addresses (match factory firmware).
My LAN factory MAC address ends in F2.

use	stock_mac	art_loc
lan	:f2		0x0
wan	:f3		0x1002
5g	:f4		0x6
2g	:f5		0x5006

Since MAC address flash locations do not really match their use in vendor
firmware (e.g. address from 5 GHz calibration data is assigned to 2.4 GHz
WiFi), just calculate the MAC addresses with an offset based on 0x0 address.

Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
[add MAC address comment]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-04-07 01:00:10 +02:00
Alex Lewontin
a0d1451088 ramips: harmonize Netgear R6120 DT LED node names
This changes the node names for the LEDs in the Netgear R6120
device-tree file to provide consistency with other devices.

Signed-off-by: Alex Lewontin <alex.c.lewontin@gmail.com>
[improve commit title/message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-04-06 17:08:38 +02:00
Lim Guo Wei
bf9b742cd4 ath79: add support for TP-Link TL-MR3420 v3
This adds support for the TP-Link TL-MR3420 v3, a later revision of the
v2 with an external gpiochip similar to TP-Link Archer C7 v4.

Specifications:

SOC: Qualcomm Atheros QCA9531
CPU: 650MHz
Flash: 4 MiB
RAM: 32 MiB
WLAN: Qualcomm Atheros QCA9531 bgn 2T2R 2.4 GHz
Ethernet: 5 ports (100M)

Flashing instructions:

- Flash factory image from OEM WebUI:
  openwrt-ath79-tiny-tplink_tl-mr3420-v3-squashfs-factory.bin
- Sysupgrade from ath79 image:
  openwrt-ath79-tiny-tplink_tl-mr3420-v3-squashfs-sysupgrade.bin

Signed-off-by: Lim Guo Wei <limguowei@gmail.com>
[remove SUPPORTED devices, some typo adjustments, fix WAN MAC
address, fix sorting in 01_leds]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-04-06 11:55:24 +02:00
Adrian Schmutzler
c3083b9649 ipq806x: remove support for kernel 4.14
This target has been on kernel 4.19 for several months [1] and
already uses kernel 5.4 as testing kernel. Therefore, it should
not be necessary to keep support for kernel 4.14 as well.

[1] 2a82e0e1ca ("ipq806x: switch to 4.19 kernel version")

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Acked-by: Stefan Lippers-Hollmann <s.l-h@gmx.de> [ipq8065/nbg6817]
2020-04-06 09:58:11 +02:00
Kip Porterfield
4b8d274456 ramips: add DTS triggers to USB LEDs for F9K1109v1
Alter DTS for Belkin F9K1109v1 to trigger USB leds from the echi/ochi
ports.

Signed-off-by: Kip Porterfield <kip.porterfield@gmail.com>
2020-04-06 09:57:28 +02:00
John Crispin
86db1f69c4 mediatek: set v5.4 as default
Signed-off-by: John Crispin <john@phrozen.org>
2020-04-06 07:07:42 +02:00
John Crispin
8021652478 mediatek: add hw flow table offloading
Signed-off-by: John Crispin <john@phrozen.org>
2020-04-06 07:07:42 +02:00
John Crispin
af5a17dbb2 mediatek: add support for rtl8367c
Signed-off-by: John Crispin <john@phrozen.org>
2020-04-06 07:07:42 +02:00
John Crispin
08df22e2ab mediatek: drop v4.14 support
Signed-off-by: John Crispin <john@phrozen.org>
2020-04-06 07:07:42 +02:00
John Crispin
e2ceb8dd93 mediatek: more v5.4 fixes
These are all backports and/or on their way upstream.

Signed-off-by: John Crispin <john@phrozen.org>
2020-04-06 07:07:42 +02:00
John Crispin
beb9820ed3 mediatek: consolidate partition names and settings
Signed-off-by: John Crispin <john@phrozen.org>
2020-04-06 07:07:42 +02:00
John Crispin
bce39e1d00 mediatek: fix elecom board name
menuconfig was showing the the company name twice.

Signed-off-by: John Crispin <john@phrozen.org>
2020-04-06 07:07:42 +02:00
John Crispin
6786dc26a2 generic: fix flow table hw offload
Make the driver work with recent upstream changes.

Signed-off-by: John Crispin <john@phrozen.org>
2020-04-06 07:07:42 +02:00
Chuanhong Guo
95bd6a04b5 ramips: fix path for dma-ralink and mtk-hsdma
These two drivers were available in drivers/staging in 5.4.
Fix driver paths for them.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2020-04-05 18:16:17 +08:00
Chuanhong Guo
f0f35fdac1 Revert "generic: 5.4: Add 4B_OPCODES flag to w25q256"
This reverts commit d7f21940bc.

Winbond W25Q256FV and W25Q256JV both uses 0xef4019 as JEDEC ID,
but only the latter has proper 4B_OPCODES support.
W25Q256FV has all 4B read instructions but it lacks a 4B page program
instruction, causing the entire flash to be read-only.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2020-04-05 12:07:47 +08:00
Thibaut VARÈNE
fdac4c085d ath79: improve mikrotik-caldata.sh
Reduce unnecessary flash wear and be tidy:
- Run the extraction only if necessary
- Extract temporary file to /tmp
- cleanup after execution

Tested-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
2020-04-04 11:18:58 +01:00
INAGAKI Hiroshi
817e132332 kernel: rtl8367b: use id as a bit offset for BYPASS_LINE_RATE
In RTL8367B (RTL8367RB/RTL8367R-VB), the driver in GPL tars of the
devices with this switch directly uses the ID of external interface
as a bit offset.

We should use the same way.

ref (RTL8367B):
  - ASUS RT-N56U
  - TP-Link Archer C2 v1

ref (RTL8367):
  - TP-Link TL-WR2543ND v1

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2020-04-04 17:20:13 +08:00
INAGAKI Hiroshi
e714cf4195 kernel: rtl8367b: fix DEBUG register address for extif2
RTL8367B_CHIP_DEBUG1_REG (0x1304) is for external interface 1. For
external interface 2, use RTL8367B_CHIP_DEBUG2_REG (0x13e2) instead.

Fixes: 9801d61c4a ("kernel: rtl8367b: add configuration for extif2")
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2020-04-04 16:55:47 +08:00
Chuanhong Guo
4d979a4d19 ramips: mt7621: bringup dsa master on preinit
DSA requires master netdev to be up before any of its slave ports.
Bring it up during preinit so that the first lan port can be used
on failsafe.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2020-04-04 16:30:16 +08:00
Chuanhong Guo
838f1fbb50 ramips: mt7621: disable image for mikrotik_rbm11g
It's unknown which switch port is used on mikrotik_rbm11g.
Disable this image until someone with actual device fixes this problem.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2020-04-04 15:25:36 +08:00
Chuanhong Guo
a8d62a4eb1 ramips: remove set_preinit_iface script
This script isn't suitable for mt7621 anymore due to switching to DSA
and it needs a different preinit script.
Generic preinit logic in package/base-files has the ability to parse
board.json and pick preinit iface accordingly. Just remove this script
instead of moving it into subtargets.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2020-04-04 14:56:14 +08:00
DENG Qingfang
764cc5c6a6 generic: mt7530: fix null pointer dereferencing in port5 setup
The 2nd gmac of mediatek soc ethernet may not be connected to a PHY
and a phy-handle isn't always available.
Unfortunately, mt7530 dsa driver assumes that the 2nd gmac is always
connected to switch port 5 and setup mt7530 according to phy address
of 2nd gmac node, causing null pointer dereferencing when phy-handle
isn't defined in dts.
This commit fix this setup code by checking return value of
of_parse_phandle before using it.

Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
2020-04-04 14:56:14 +08:00
DENG Qingfang
3624721ef1 generic: backport support for MT7530 DSA port mirroring
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
2020-04-04 14:56:14 +08:00
René van Dorst
ae6b4d3f86 ramips: correct MTC WR1201 LAN ports names
LAN ports of MTC WR1201 are reversed, so correct their names

Signed-off-by: René van Dorst <opensource@vdorst.com>
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
2020-04-04 14:56:14 +08:00
DENG Qingfang
10f27c6f00 ramips: mt7621: add new NAND driver
Add new NAND driver for MT7621

Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
2020-04-04 14:56:14 +08:00
DENG Qingfang
92daa06f22 ramips: mt7621: drop obsolete mx25l25635f dts hack
5.4 kernel has fixed this issue, so the hack is no longer needed.

Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
2020-04-04 14:56:14 +08:00
DENG Qingfang
437aaae6ca Revert "ramips: mt7621: disable images for gehua_ghl-r-001"
This reverts commit 28080d54d2.
Support for MX25L25635F flash is fixed upstream

Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
2020-04-04 14:56:14 +08:00
DENG Qingfang
dcf7fdbdbf ramips: move swconfig to subtargets except for MT7621
As MT7621 does not use swconfig anymore, move the package swconfig to
other subtargets.

Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
2020-04-04 14:56:14 +08:00
DENG Qingfang
6570960913 ramips: mt7621: introduce 'soc_device' initialization
mt7621 SoC has its own 'ralink_soc_info' structure with some
information about the soc itself. Pcie controller and pcie phy
drivers for this soc which are still in staging git tree make uses
of 'soc_device_attribute' looking for revision 'E2' in order to
know if reset lines are or not inverted. This way of doing things
seems to be necessary in order to make things clean and properly.
Hence, introduce this 'soc_device' to be able to properly use those
attributes in drivers. Also set 'data' pointer points to the struct
'ralink_soc_info' to be able to export also current soc information
using this mechanism.

Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
2020-04-04 14:56:14 +08:00
DENG Qingfang
c24d6111f4 ramips: fix MikroTik 750Gr3 LAN ports names
They are labeled as LAN2..LAN5 instead of LAN1..LAN4

Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
2020-04-04 14:56:14 +08:00
DENG Qingfang
53b66248f4 ramips: use SoC I2C instead of bitbanged for Ubiquiti ER-X-SFP
The original idea of bitbanged I2C is to use i2c-gpio-custom
Since i2c-gpio-custom is no longer available on 5.4, use SoC I2C instead

Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
2020-04-04 14:56:14 +08:00
DENG Qingfang
5acd1ed0be ramips: mt7621: fix Ubiquiti ER-X ports names and MAC addresses
The name of each user port should be eth0..4, instead of lan1..4
and there is no WAN port. Rename them to match the official firmware.
To avoid conflict with the master port (gmac0), rename it to "dsa".

The official firmware assigns MAC address in this way:
eth0 = label mac
eth1 = label mac + 1
...
eth4 = label mac + 4

Since we have switched to DSA, it's possible to use different MAC for each port.

Acked-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
2020-04-04 14:56:14 +08:00
DENG Qingfang
3211c983fd ramips: mt7621: net-label support
Add support for renaming ethernet interfaces in DTS

Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
2020-04-04 14:56:14 +08:00
DENG Qingfang
1dce5c8a28 ramips: mt7621: switch kernel version to 5.4
After all dts and config changes, 4.14 no longer works on mt7621.
Switch it to 5.4 directly.

Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
2020-04-04 14:56:14 +08:00
DENG Qingfang
c9f4f765c8 ramips: mt7621: change default ramips_setup_interfaces configuration
Most of MT7621 boards have LAN1~4 and WAN, so make this as the default

Acked-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
2020-04-04 14:56:14 +08:00
DENG Qingfang
d2b9461a55 ramips: mt7621 remove unused pinctrl groups in dts
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
[split commit, remove leftover uart3->gpio setup]
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2020-04-04 14:52:12 +08:00
DENG Qingfang
30644bc579 ramips: mt7621: update dts/defconfig for DSA
update dts and network/LED configuration for DSA driver.
sysupgrade from images prior to this commit with config preserved
will cause broken ethernet setup.

Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
Acked-by: Jo-Philipp Wich <jo@mein.io>
[split commit]
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2020-04-04 14:40:44 +08:00
DENG Qingfang
7bd19dbe99 ramips: mt7621: backport GPIO driver fix
Backport 2 patches from linux-next to fix mt7621 GPIO driver

Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
2020-04-04 14:14:43 +08:00
DENG Qingfang
9ebb85c372 ramips: mt7621: update PCIe node in dtsi
Update PCIe node in dtsi to match the new driver

Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
2020-04-04 14:14:43 +08:00
DENG Qingfang
d21d6ea454 ramips: mt7621: backport PCIe driver fixes from staging-test
Backport mt7621-pci/mt7621-pci-phy fixes from staging-test

Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
2020-04-04 14:14:43 +08:00
DENG Qingfang
66984646c2 ramips: mt7621: update pinctrl nodes
Upstream GPIO driver uses "groups" "function" properties

Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
2020-04-04 14:13:05 +08:00
DENG Qingfang
60f691dae4 ramips: mt7621: convert GPIO dts refs
The upstream driver does not use &gpio0..2 banks notation anymore,
so convert them to &gpio

Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
2020-04-04 14:13:05 +08:00
DENG Qingfang
783fc8e553 ramips: mt7621: replace gpio/eth nodes in mt7621.dtsi
There's different gpio and ethernet drivers upstream for mt7621.
Update these two nodes to match upstream dt bindings.

Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
2020-04-04 14:10:58 +08:00
DENG Qingfang
99d210d6a0 ramips: mt7621: refresh kernel config
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
2020-04-04 12:04:14 +08:00