If the driver uses .sta_add, station entries are only uploaded after the sta
is in assoc state. Fix early station rate table updates by deferring them
until the sta has been uploaded
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: maurerr <mariusd84@gmail.com>
he_mu_beamformer only accepts values of 0 and 1 according to the hostapd
documentation.
Signed-off-by: David Bauer <mail@david-bauer.net>
Signed-off-by: maurerr <mariusd84@gmail.com>
With upstream commit f81f9f0ebac5 ("rockchip: rockpro64: initialize USB in
preboot") CONFIG_USE_PREBOOT was enabled on the RockPro64, which is causing
boot issues when a eMMC is used, as a workaround will temporarily disable
this option.
Signed-off-by: Marty Jones <mj8263788@gmail.com>
[Improve patch description]
Signed-off-by: David Bauer <mail@david-bauer.net>
Signed-off-by: maurerr <mariusd84@gmail.com>
Enable support for the Ubiquiti UniFi Outdoor+ RF filter via
device-tree. The old way of using platform data is not required anymore,
as it was only used on the now removed ar71xx target.
Signed-off-by: David Bauer <mail@david-bauer.net>
Signed-off-by: maurerr <mariusd84@gmail.com>
Replace with sed as done elsewhere.
Fixes error with at least btrfs-progs:
Package '@LIBSELINUX@', required by 'mount', not found
Package '@LIBCRYPTSETUP@', required by 'mount', not foun
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Signed-off-by: maurerr <mariusd84@gmail.com>
The two required tools fail to identify their version when not compiling
from a git clone, patch that in and pass on the used commit hashes.
Upon boot it now prints "WTMI-devel-18.12.1-5598e150".
Signed-off-by: Andre Heider <a.heider@gmail.com>
Signed-off-by: maurerr <mariusd84@gmail.com>
The cpufreq issue has been identified and a fix is in the process of beeing
upstreamed [0].
Bump the boards to the default 1000MHz so they can run at that frequency
once the fix is merged. Until then the boards are stuck at 800MHz (just
claiming to run 1000Hz, which is a lie).
[0] https://lore.kernel.org/linux-arm-kernel/20210114124032.12765-1-pali@kernel.org/
Signed-off-by: Andre Heider <a.heider@gmail.com>
Signed-off-by: maurerr <mariusd84@gmail.com>
u-boot now detects emmc variants at runtime, we don't need to build
seperate binaries anymore.
Signed-off-by: Andre Heider <a.heider@gmail.com>
Signed-off-by: maurerr <mariusd84@gmail.com>
Starting with u-boot v2021.01 a single binary will be used for non-emmc
and emmc variants.
Signed-off-by: Andre Heider <a.heider@gmail.com>
Signed-off-by: maurerr <mariusd84@gmail.com>
v5.10 has been released for strace. As such, let's go ahead bring in the
latest version of this package.
See here for the changelog:
https://github.com/strace/strace/releases/tag/v5.10
Signed-off-by: Geordan Neukum <gneukum1@gmail.com>
Signed-off-by: maurerr <mariusd84@gmail.com>
Pstore (persistent store) can be used to stash debug information (kernel
console, panics, ftrace) across reboots or crashes. If the filesystem is
present, mount it.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: maurerr <mariusd84@gmail.com>
Changelog:
- ath10k-ct: Pull in some upstream patches.
Runtime-tested on ipq806x (Netgear R7800).
Signed-off-by: Michael Yartys <michael.yartys@gmail.com>
Signed-off-by: maurerr <mariusd84@gmail.com>
/lib/functions.sh was executable for no obvious reason and its
execute property was even checked in package-ipkg.mk just to
source it afterwards.
Remove the execute bit and shebang as this is clearly a library.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Reviewed-by: Philip Prindeville <philipp@redfish-solutions.com>
Signed-off-by: maurerr <mariusd84@gmail.com>
This drops the shebang from another bunch of files in various /lib
folders, as these are sourced and the shebang is useless.
Fix execute bit in one case, too.
This should cover almost all trivial cases now, i.e. where /lib is
actually used for library files.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: maurerr <mariusd84@gmail.com>
65abbcd9f6fb mt76: usb: process URBs with status EPROTO properly
3199ef5fa35e mt76: mt7615: set mcu country code in mt7615_mcu_set_channel_domain()
5c86d5bb079b mt76: mt7915: Remove unneeded semicolon
3f546330b59d mt76: mt7915: support TxBF for DBDC
032ad7e02545 mt76: mt7615: unify init work
cc3f23d1e654 mt76: mt7915: bring up the WA event rx queue for band1
fa3d334a0e22 mt76: fix crash on tearing down ext phy
c4c9c402d14a mt76: mt7915: fix vif sta index for DBDC
eca2f0ec0d4c mt76: mt7915: fix command id for txbf action
c828124ef9a5 mt76: mt7915: add support for using a secondary PCIe link for gen1
dbaf0f4679f3 mt76: mt7915: make vif index per adapter instead of per band
fb3e5ce1eb00 mt76: move vif_mask back from mt76_phy to mt76_dev
be2bea66d6e3 mt76: mt7915: detect wrong nss eeprom parameter on dbdc cards
8dc5d4a0da7c Revert "mt76: mt7915: fix vif sta index for DBDC"
8c796a33781c mt76: mt7915: only set int1 when using the second hif
4eb5caaf6cc1 mt76: reduce q->lock hold time
0714890bf0fd mt76: mt7615: reduce VHT maximum MPDU length
2f85aa5cbc62 mt76: mt7915: avoid writes to MT_PCIE_RECOG_ID when not using gen1 devices
8696919d9aae mt76: dma: fix a possible memory leak in mt76_add_fragment()
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: maurerr <mariusd84@gmail.com>
This commit is only added to keep the PKG_RELEASE correct after fixing
the $(COMMITCOUNT) logic in the previous commit.
This way the PKG_RELEASE stays the same while the compiled packages
content isn't changed.
Signed-off-by: Paul Spooren <mail@aparcar.org>
Signed-off-by: maurerr <mariusd84@gmail.com>
Certificate signature algorithm was being set after call to
`wc_MakeCert`, resulting in a mismatch between specified signature in
certificate and the actual signature type.
Signed-off-by: Jeffrey Elms <jeff@wolfssl.com>
[fix commit subject, use COMMITCOUNT]
Signed-off-by: Paul Spooren <mail@aparcar.org>
Signed-off-by: maurerr <mariusd84@gmail.com>
Use the latest stable kernel since the previous 5.8.x series is EOL.
Also drop the following patches recently accepted upstream:
* 001-libbpf-ensure-no-local-symbols-counted-in-ABI-check.patch
* 002-libbpf-fix-build-failure-from-uninitialized-variable.patch
* 003-bpftool-allow-passing-BPFTOOL_VERSION-to-make.patch
* 004-v5.9-bpftool-use-only-ftw-for-file-tree-parsing.patch
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Signed-off-by: maurerr <mariusd84@gmail.com>
dnsmasq v2.83 has a bug in handling duplicate queries which means it may
try to reply using the incorrect network socket. This is especially
noticeable in dual stack environments where replies may be mis-directed to
IPv4 addresses on an IPv6 socket or IPv6 addresses on an IPv4 socket.
This results in system log spam such as:
dnsmasq[16020]: failed to send packet: Network unreachable
dnsmasq[16020]: failed to send packet: Address family not supported by protocol
dnsmasq v2.84test3 resolves these issues.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Signed-off-by: maurerr <mariusd84@gmail.com>
FCC ID: A8J-EAP1200H
Engenius EAP1200H is an indoor wireless access point with
1 Gb ethernet port, dual-band wireless,
internal antenna plates, and 802.3at PoE+
**Specification:**
- QCA9557 SOC
- QCA9882 WLAN PCI card, 5 GHz, 2x2, 26dBm
- AR8035-A PHY RGMII GbE with PoE+ IN
- 40 MHz clock
- 16 MB FLASH MX25L12845EMI-10G
- 2x 64 MB RAM NT5TU32M16FG
- UART at J10 populated
- 4 internal antenna plates (5 dbi, omni-directional)
- 5 LEDs, 1 button (power, eth0, 2G, 5G, WPS) (reset)
**MAC addresses:**
MAC addresses are labeled as ETH, 2.4G, and 5GHz
Only one Vendor MAC address in flash
eth0 ETH *:a2 art 0x0
phy1 2.4G *:a3 ---
phy0 5GHz *:a4 ---
**Serial Access:**
the RX line on the board for UART is shorted to ground by resistor R176
therefore it must be removed to use the console
but it is not necessary to remove to view boot log
optionally, R175 can be replaced with a solder bridge short
the resistors R175 and R176 are next to the UART RX pin at J10
**Installation:**
2 ways to flash factory.bin from OEM:
Method 1: Firmware upgrade page:
OEM webpage at 192.168.1.1
username and password "admin"
Navigate to "Firmware Upgrade" page from left pane
Click Browse and select the factory.bin image
Upload and verify checksum
Click Continue to confirm and wait 3 minutes
Method 2: Serial to load Failsafe webpage:
After connecting to serial console and rebooting...
Interrupt uboot with any key pressed rapidly
execute `run failsafe_boot` OR `bootm 0x9fd70000`
wait a minute
connect to ethernet and navigate to
"192.168.1.1/index.htm"
Select the factory.bin image and upload
wait about 3 minutes
**Return to OEM:**
If you have a serial cable, see Serial Failsafe instructions
otherwise, uboot-env can be used to make uboot load the failsafe image
*DISCLAIMER*
The Failsafe image is unique to Engenius boards.
If the failsafe image is missing or damaged this will brick the device
DO NOT downgrade to ar71xx this way, it can cause kernel loop or halt
ssh into openwrt and run
`fw_setenv rootfs_checksum 0`
reboot, wait 3 minutes
connect to ethernet and navigate to 192.168.1.1/index.htm
select OEM firmware image from Engenius and click upgrade
**TFTP recovery:**
Requires serial console, reset button does nothing
rename initramfs to 'vmlinux-art-ramdisk'
make available on TFTP server at 192.168.1.101
power board, interrupt boot
execute tftpboot and bootm 0x81000000
NOTE: TFTP is not reliable due to bugged bootloader
set MTU to 600 and try many times
**Format of OEM firmware image:**
The OEM software of EAP1200H is a heavily modified version
of Openwrt Kamikaze. One of the many modifications
is to the sysupgrade program. Image verification is performed
simply by the successful ungzip and untar of the supplied file
and name check and header verification of the resulting contents.
To form a factory.bin that is accepted by OEM Openwrt build,
the kernel and rootfs must have specific names...
openwrt-ar71xx-generic-eap1200h-uImage-lzma.bin
openwrt-ar71xx-generic-eap1200h-root.squashfs
and begin with the respective headers (uImage, squashfs).
Then the files must be tarballed and gzipped.
The resulting binary is actually a tar.gz file in disguise.
This can be verified by using binwalk on the OEM firmware images,
ungzipping then untaring.
Newer EnGenius software requires more checks but their script
includes a way to skip them, otherwise the tar must include
a text file with the version and md5sums in a deprecated format.
The OEM upgrade script is at /etc/fwupgrade.sh.
OKLI kernel loader is required because the OEM software
expects the kernel to be no greater than 1536k
and the factory.bin upgrade procedure would otherwise
overwrite part of the kernel when writing rootfs.
Note on PLL-data cells:
The default PLL register values will not work
because of the external AR8035 switch between
the SOC and the ethernet port.
For QCA955x series, the PLL registers for eth0 and eth1
can be see in the DTSI as 0x28 and 0x48 respectively.
Therefore the PLL registers can be read from uboot
for each link speed after attempting tftpboot
or another network action using that link speed
with `md 0x18050028 1` and `md 0x18050048 1`.
The clock delay required for RGMII can be applied
at the PHY side, using the at803x driver `phy-mode`.
Therefore the PLL registers for GMAC0
do not need the bits for delay on the MAC side.
This is possible due to fixes in at803x driver
since Linux 5.1 and 5.3
Signed-off-by: Michael Pratt <mcpratt@pm.me>
Signed-off-by: maurerr <mariusd84@gmail.com>
This is a helpful utility, but it does not have any dependencies
in this repository. Move it to packages feed.
The package does not seem to have a maintainer.
Cc: Jo-Philipp Wich <jo@mein.io>
Cc: Nick Hainke <vincent@systemli.org>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: maurerr <mariusd84@gmail.com>
This is a helpful utility, but it does not have any dependencies
in this repository. Move it to packages feed.
Cc: Jo-Philipp Wich <jo@mein.io>
Cc: Nick Hainke <vincent@systemli.org>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: maurerr <mariusd84@gmail.com>
Use `$(AUTORELEASE)` variable rather than setting a PKG_RELEASE
on every commit manually.
Signed-off-by: Paul Spooren <mail@aparcar.org>
Signed-off-by: maurerr <mariusd84@gmail.com>
The newly added `$(COMMITCOUNT)` varialbe allows automatic versioning
based on the number of Git commits of a package. Replace *tedious to
bump* and *merge conflict causing* `PKG_RELEASE` and replace it with
`$(COMMITCOUNT)`.
Signed-off-by: Paul Spooren <mail@aparcar.org>
Signed-off-by: maurerr <mariusd84@gmail.com>
This package is not needed in base. It will be imported in the packages
feed.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
Signed-off-by: maurerr <mariusd84@gmail.com>
This package is not needed in base. It will be imported in the packages
feed.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
Signed-off-by: maurerr <mariusd84@gmail.com>
Xiaomi Mi Router 4 is the same as Xiaomi Mi Router 3G, except for
the RAM (256Mib→128Mib), LEDs and gpio (MiNet button).
Specifications:
Power: 12 VDC, 1 A
Connector type: barrel
CPU1: MediaTek MT7621A (880 MHz, 4 cores)
FLA1: 128 MiB (ESMT F59L1G81MA)
RAM1: 128 MiB (ESMT M15T1G1664A)
WI1 chip1: MediaTek MT7603EN
WI1 802dot11 protocols: bgn
WI1 MIMO config: 2x2:2
WI1 antenna connector: U.FL
WI2 chip1: MediaTek MT7612EN
WI2 802dot11 protocols: an+ac
WI2 MIMO config: 2x2:2
WI2 antenna connector: U.FL
ETH chip1: MediaTek MT7621A
Switch: MediaTek MT7621A
UART Serial
[o] TX
[o] GND
[o] RX
[ ] VCC - Do not connect it
MAC addresses as verified by OEM firmware:
use address source
LAN *:c2 factory 0xe000 (label)
WAN *:c3 factory 0xe006
2g *:c4 factory 0x0000
5g *:c5 factory 0x8000
Flashing instructions:
1.Create a simple http server (nginx etc)
2.set uart enable
To enable writing to the console, you must reset to factory settings
Then you see uboot boot, press the keyboard 4 button (enter uboot command line)
If it is not successful, repeat the above operation of restoring the factory settings.
After entering the uboot command line, type:
setenv uart_en 1
saveenv
boot
3.use shell in uart
cd /tmp
wget http://"your_computer_ip:80"/openwrt-ramips-mt7621-xiaomi_mir4-squashfs-kernel1.bin
wget http://"your_computer_ip:80"/openwrt-ramips-mt7621-xiaomi_mir4-squashfs-rootfs0.bin
mtd write openwrt-ramips-mt7621-xiaomi_mir4-squashfs-kernel1.bin kernel1
mtd write openwrt-ramips-mt7621-xiaomi_mir4-squashfs-rootfs0.bin rootfs0
nvram set flag_try_sys1_failed=1
nvram commit
reboot
4.login to the router http://192.168.1.1/
Installation via Software exploit
Find the instructions in the https://github.com/acecilia/OpenWRTInvasion
Signed-off-by: Dmytro Oz <sequentiality@gmail.com>
[commit message facelift, rebase onto shared DTSI/common device
definition, bump uboot-envtools]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: maurerr <mariusd84@gmail.com>
Device specifications:
======================
* Qualcomm/Atheros QCA9558 ver 1 rev 0
* 720/600/240 MHz (CPU/DDR/AHB)
* 128 MB of RAM
* 16 MB of SPI NOR flash
- 2x 7 MB available; but one of the 7 MB regions is the recovery image
* 3T3R 2.4 GHz Wi-Fi (11n)
* 3T3R 5 GHz Wi-Fi (11ac)
* 6x GPIO-LEDs (2x wifi, 2x status, 1x lan, 1x power)
* 1x GPIO-button (reset)
* external h/w watchdog (enabled by default))
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 1x ethernet
- AR8035 ethernet PHY (RGMII)
- 10/100/1000 Mbps Ethernet
- 802.3af POE
- used as LAN interface
* 12-24V 1A DC
* internal antennas
Flashing instructions:
======================
Various methods can be used to install the actual image on the flash.
Two easy ones are:
ap51-flash
----------
The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the image to the u-boot when the device boots up.
initramfs from TFTP
-------------------
The serial console must be used to access the u-boot shell during bootup.
It can then be used to first boot up the initramfs image from a TFTP server
(here with the IP 192.168.1.21):
setenv serverip 192.168.1.21
setenv ipaddr 192.168.1.1
tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr
The actual sysupgrade image can then be transferred (on the LAN port) to the
device via
scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/
On the device, the sysupgrade must then be started using
sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin
Signed-off-by: Sven Eckelmann <sven@narfation.org>
[rebase, add LED migration]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: maurerr <mariusd84@gmail.com>
Device specifications:
======================
* Qualcomm/Atheros QCA9558 ver 1 rev 0
* 720/600/240 MHz (CPU/DDR/AHB)
* 128 MB of RAM
* 16 MB of SPI NOR flash
- 2x 7 MB available; but one of the 7 MB regions is the recovery image
* 3T3R 2.4 GHz Wi-Fi (11n)
* 3T3R 5 GHz Wi-Fi (11ac)
* 6x GPIO-LEDs (2x wifi, 2x status, 1x lan, 1x power)
* 1x GPIO-button (reset)
* external h/w watchdog (enabled by default))
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 1x ethernet
- AR8035 ethernet PHY (RGMII)
- 10/100/1000 Mbps Ethernet
- 802.3af POE
- used as LAN interface
* 12-24V 1A DC
* internal antennas
Flashing instructions:
======================
Various methods can be used to install the actual image on the flash.
Two easy ones are:
ap51-flash
----------
The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the image to the u-boot when the device boots up.
initramfs from TFTP
-------------------
The serial console must be used to access the u-boot shell during bootup.
It can then be used to first boot up the initramfs image from a TFTP server
(here with the IP 192.168.1.21):
setenv serverip 192.168.1.21
setenv ipaddr 192.168.1.1
tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr
The actual sysupgrade image can then be transferred (on the LAN port) to the
device via
scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/
On the device, the sysupgrade must then be started using
sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin
Signed-off-by: Sven Eckelmann <sven@narfation.org>
[rebase, apply shared DTSI/device node, add LED migration]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: maurerr <mariusd84@gmail.com>
Device specifications:
======================
* Qualcomm/Atheros QCA9558 ver 1 rev 0
* 720/600/240 MHz (CPU/DDR/AHB)
* 128 MB of RAM
* 16 MB of SPI NOR flash
- 2x 7 MB available; but one of the 7 MB regions is the recovery image
* 3T3R 2.4 GHz Wi-Fi
* 3T3R 5 GHz Wi-Fi
* 6x GPIO-LEDs (2x wifi, 2x status, 1x lan, 1x power)
* 1x GPIO-button (reset)
* external h/w watchdog (enabled by default))
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 1x ethernet
- AR8035 ethernet PHY (RGMII)
- 10/100/1000 Mbps Ethernet
- 802.3af POE
- used as LAN interface
* 12-24V 1A DC
* internal antennas
Flashing instructions:
======================
Various methods can be used to install the actual image on the flash.
Two easy ones are:
ap51-flash
----------
The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the image to the u-boot when the device boots up.
initramfs from TFTP
-------------------
The serial console must be used to access the u-boot shell during bootup.
It can then be used to first boot up the initramfs image from a TFTP server
(here with the IP 192.168.1.21):
setenv serverip 192.168.1.21
setenv ipaddr 192.168.1.1
tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr
The actual sysupgrade image can then be transferred (on the LAN port) to the
device via
scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/
On the device, the sysupgrade must then be started using
sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin
Signed-off-by: Sven Eckelmann <sven@narfation.org>
[rebase, add LED migration]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: maurerr <mariusd84@gmail.com>
Device specifications:
======================
* Qualcomm/Atheros QCA9558 ver 1 rev 0
* 720/600/240 MHz (CPU/DDR/AHB)
* 128 MB of RAM
* 16 MB of SPI NOR flash
- 2x 7 MB available; but one of the 7 MB regions is the recovery image
* 3T3R 2.4 GHz Wi-Fi
* 3T3R 5 GHz Wi-Fi
* 6x GPIO-LEDs (2x wifi, 2x status, 1x lan, 1x power)
* 1x GPIO-button (reset)
* external h/w watchdog (enabled by default))
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 1x ethernet
- AR8035 ethernet PHY (RGMII)
- 10/100/1000 Mbps Ethernet
- 802.3af POE
- used as LAN interface
* 12-24V 1A DC
* internal antennas
Flashing instructions:
======================
Various methods can be used to install the actual image on the flash.
Two easy ones are:
ap51-flash
----------
The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the image to the u-boot when the device boots up.
initramfs from TFTP
-------------------
The serial console must be used to access the u-boot shell during bootup.
It can then be used to first boot up the initramfs image from a TFTP server
(here with the IP 192.168.1.21):
setenv serverip 192.168.1.21
setenv ipaddr 192.168.1.1
tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr
The actual sysupgrade image can then be transferred (on the LAN port) to the
device via
scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/
On the device, the sysupgrade must then be started using
sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin
Signed-off-by: Sven Eckelmann <sven@narfation.org>
[rebase, add LED migration]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: maurerr <mariusd84@gmail.com>
Device specifications:
======================
* Qualcomm/Atheros AR9344 rev 2
* 560/450/225 MHz (CPU/DDR/AHB)
* 128 MB of RAM
* 16 MB of SPI NOR flash
- 2x 7 MB available; but one of the 7 MB regions is the recovery image
* 2T2R 2.4 GHz Wi-Fi
* 2T2R 5 GHz Wi-Fi
* 8x GPIO-LEDs (6x wifi, 1x wps, 1x power)
* 1x GPIO-button (reset)
* external h/w watchdog (enabled by default))
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 1x ethernet
- AR8035 ethernet PHY (RGMII)
- 10/100/1000 Mbps Ethernet
- 802.3af POE
- used as LAN interface
* 12-24V 1A DC
* internal antennas
Flashing instructions:
======================
Various methods can be used to install the actual image on the flash.
Two easy ones are:
ap51-flash
----------
The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the image to the u-boot when the device boots up.
initramfs from TFTP
-------------------
The serial console must be used to access the u-boot shell during bootup.
It can then be used to first boot up the initramfs image from a TFTP server
(here with the IP 192.168.1.21):
setenv serverip 192.168.1.21
setenv ipaddr 192.168.1.1
tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr
The actual sysupgrade image can then be transferred (on the LAN port) to the
device via
scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/
On the device, the sysupgrade must then be started using
sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin
Signed-off-by: Sven Eckelmann <sven@narfation.org>
[rebase, add LED migration]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: maurerr <mariusd84@gmail.com>
Device specifications:
======================
* Qualcomm/Atheros AR9344 rev 2
* 560/450/225 MHz (CPU/DDR/AHB)
* 128 MB of RAM
* 16 MB of SPI NOR flash
- 2x 7 MB available; but one of the 7 MB regions is the recovery image
* 2T2R 2.4 GHz Wi-Fi
* 2T2R 5 GHz Wi-Fi
* 4x GPIO-LEDs (2x wifi, 1x wps, 1x power)
* 1x GPIO-button (reset)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 1x ethernet
- AR8035 ethernet PHY (RGMII)
- 10/100/1000 Mbps Ethernet
- 802.3af POE
- used as LAN interface
* 12-24V 1A DC
* internal antennas
Flashing instructions:
======================
Various methods can be used to install the actual image on the flash.
Two easy ones are:
ap51-flash
----------
The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the image to the u-boot when the device boots up.
initramfs from TFTP
-------------------
The serial console must be used to access the u-boot shell during bootup.
It can then be used to first boot up the initramfs image from a TFTP server
(here with the IP 192.168.1.21):
setenv serverip 192.168.1.21
setenv ipaddr 192.168.1.1
tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr
The actual sysupgrade image can then be transferred (on the LAN port) to the
device via
scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/
On the device, the sysupgrade must then be started using
sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin
Signed-off-by: Sven Eckelmann <sven@narfation.org>
[rebase, make WLAN LEDs consistent, add LED migration]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: maurerr <mariusd84@gmail.com>
The "cidr_contains6" functions clones the given cidr. The contains4
does not clone the cidr. Both functions do not behave the same.
I see no reason to push the cidr. I think that we get only a negligible
performance gain, but it makes ipv4 and ipv6 equal again.
Signed-off-by: Nick Hainke <vincent@systemli.org>
Signed-off-by: maurerr <mariusd84@gmail.com>
This fixes the following security problems in dnsmasq:
* CVE-2020-25681:
Dnsmasq versions before 2.83 is susceptible to a heap-based buffer
overflow in sort_rrset() when DNSSEC is used. This can allow a remote
attacker to write arbitrary data into target device's memory that can
lead to memory corruption and other unexpected behaviors on the target
device.
* CVE-2020-25682:
Dnsmasq versions before 2.83 is susceptible to buffer overflow in
extract_name() function due to missing length check, when DNSSEC is
enabled. This can allow a remote attacker to cause memory corruption
on the target device.
* CVE-2020-25683:
Dnsmasq version before 2.83 is susceptible to a heap-based buffer
overflow when DNSSEC is enabled. A remote attacker, who can create
valid DNS replies, could use this flaw to cause an overflow in a heap-
allocated memory. This flaw is caused by the lack of length checks in
rtc1035.c:extract_name(), which could be abused to make the code
execute memcpy() with a negative size in get_rdata() and cause a crash
in Dnsmasq, resulting in a Denial of Service.
* CVE-2020-25684:
A lack of proper address/port check implemented in Dnsmasq version <
2.83 reply_query function makes forging replies easier to an off-path
attacker.
* CVE-2020-25685:
A lack of query resource name (RRNAME) checks implemented in Dnsmasq's
versions before 2.83 reply_query function allows remote attackers to
spoof DNS traffic that can lead to DNS cache poisoning.
* CVE-2020-25686:
Multiple DNS query requests for the same resource name (RRNAME) by
Dnsmasq versions before 2.83 allows for remote attackers to spoof DNS
traffic, using a birthday attack (RFC 5452), that can lead to DNS
cache poisoning.
* CVE-2020-25687:
Dnsmasq versions before 2.83 is vulnerable to a heap-based buffer
overflow with large memcpy in sort_rrset() when DNSSEC is enabled. A
remote attacker, who can create valid DNS replies, could use this flaw
to cause an overflow in a heap-allocated memory. This flaw is caused
by the lack of length checks in rtc1035.c:extract_name(), which could
be abused to make the code execute memcpy() with a negative size in
sort_rrset() and cause a crash in dnsmasq, resulting in a Denial of
Service.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: maurerr <mariusd84@gmail.com>
The referenced commit is gone, but we already have this file on our
mirror, use that one by providing the correct mirror hash.
I generated a tar.xz file with the given git commit hash using a random
fork on github and it generated the same tar.xz file as found on our
mirror so this looks correct.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: maurerr <mariusd84@gmail.com>
The referenced commit is gone, but we already have this file on our
mirror, use that one by providing the correct mirror hash.
I generated a tar.xz file with the given git commit hash using a random
fork on github and it generated the same tar.xz file as found on our
mirror so this looks correct.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: maurerr <mariusd84@gmail.com>
bcm4908 target needs to include cferam images in firmware files too
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: maurerr <mariusd84@gmail.com>
