The MikroTik wAP ac (RBwAPG-5HacD2HnD) is a dual-band dual-radio
802.11ac wireless access point with integrated antenna and two Ethernet
ports in a weatherproof enclosure. See
https://mikrotik.com/product/wap_ac for more information.
Important: this is the new ipq40xx-based wAP ac, not the older
ath79-based wAP ac (RBwAPG-5HacT2HnD), already supported in OpenWrt.
Specifications:
- SoC: Qualcomm Atheros IPQ4018
- CPU: 4x ARM Cortex A7
- RAM: 128MB
- Storage: 16MB NOR flash
- Wireless
- 2.4GHz: Built-in IPQ4018 (SoC) 802.11b/g/n 2x2:2, 2.5 dBi antennae
- 5GHz: Built-in IPQ4018 (SoC) 802.11a/n/ac 2x2:2, 2.5 dBi antennae
- Ethernet: Built-in IPQ4018 (SoC, QCA8075), 2x 1000/100/10Mb/s ports,
one with 802.3af/at PoE in
Installation:
Boot the initramfs image via TFTP, then flash the sysupgrade image using
sysupgrade. Details at https://openwrt.org/toh/mikrotik/common.
Notes:
This preserves the MAC addresses of the physical Ethernet ports:
- eth0 corresponds to the physical port labeled ETH1 and has the base
MAC address. This port can be used to power the device.
- eth1 corresponds to the physical port labeled ETH2 and has a MAC
address one greater than the base.
MAC addresses are set from /lib/preinit/05_set_iface_mac_ipq40xx.sh
rather than /etc/board.d/02_network so that they are in effect for
preinit. This should likely be done for other MikroTik devices and
possibly other non-MikroTik devices as well.
As this device has 2 physical ports, they are each connected to their
respective PHYs, allowing the link status to be visible to software.
Since they are not marked on the case with any role (such as LAN or
WAN), both are bridged to the lan network by default, although this can
easily be changed if needed.
Signed-off-by: Mark Mentovai <mark@mentovai.com>
moves and extends the current facilities, which have been
added some time ago for the the usbip utility, to support
more utilites that are shipped with the Linux kernel tree
to the SDK.
this allows to drop all the hand-waving and code for
failed previous attempts to mitigate the SDK build failures.
Fixes: bdaaf66e28 ("utils/spidev_test: build package directly from Linux")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Destination switch ports for outgoing frame can range from 0 to
CPU_PORT-1.
Refactor the code to only generate egress frame CPU headers when a valid
destination port number is available, and make the code a bit more
consistent between different switch generations. Change the dest_port
argument's type to 'unsigned int', since only positive values are valid.
This fixes the issue where egress frames on switch port 0 did not
receive a VLAN tag, because they are sent out without a CPU header.
Also fixes a potential issue with invalid (negative) egress port numbers
on RTL93xx switches.
Reported-by: Arınç ÜNAL <arinc.unal@xeront.com>
Suggested-by: Birger Koblitz <mail@birger-koblitz.de>
Tested-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Priority values passed to the egress (TX) frame header initialiser are
invalid when smaller than 0, and should not be assigned to the frame.
Queue assignment is then left to the switch core logic.
Current code for RTL83xx forces the passed priority value to be
positive, by always masking it to the lower bits, resulting in the
priority always being set and enabled. RTL93xx code doesn't even check
the value and unconditionally assigns the (32 bit) value to the (5 bit)
QID field without masking.
Fix priority assignment by only setting the AS_QID/AS_PRI flag when a
valid value is passed, and properly mask the value to not overflow the
QID/PRI field.
For RTL839x, also assign the priority to the right part of the frame
header. Counting from the leftmost bit, AS_PRI and PRI are in bits 36
and 37-39. The means they should be assigned to the third 16 bit value,
containing bits 32-47.
Tested-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Signed-off-by: Sander Vanheule <sander@svanheule.net>
The flag to enable L2 address learning on egress frames is in CPU header
bit 40, with bit 0 being the leftmost bit of the header. This
corresponds to BIT(7) in the third 16-bit value of the header.
Correctly set L2LEARNING by fixing the off-by-one error.
Fixes: 9eab76c84e ("realtek: Improve TX CPU-Tag usage")
Tested-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Signed-off-by: Sander Vanheule <sander@svanheule.net>
The flag to enable the outgoing port mask is in CPU header bit 43, with
bit 0 being the leftmost bit of the header. This corresponds to BIT(4)
in the third 16-bit value of the header.
Correctly set AS_DPM by fixing the off-by-one error.
Fixes: 9eab76c84e ("realtek: Improve TX CPU-Tag usage")
Tested-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Meraki MR26 is an EOL wireless access point featuring a
PoE ethernet port and two dual-band 3x3 MIMO 802.11n
radios and 1x1 dual-band WIFI dedicated to scanning.
Thank you Amir for the unit and PSU.
Hardware info:
SOC : Broadcom BCM53015A1KFEBG (dual-core Cortex-A9 CPU at 800 MHz)
RAM : SK hynix Inc. H5TQ1G63EFR, 1 Gbit DDR3 SDRAM = 128 MiB
NAND : Spansion S34ML01G100TF100, 1 Gbit SLC NAND Flash = 128 MiB
ETH : 1 GBit Ethernet Port - PoE
WIFI1 : Broadcom BCM43431KMLG, BCM43431 802.11 abgn
WIFI1 : Broadcom BCM43431KMLG, BCM43431 802.11 abgn
WIFI3 : Broadcom BCM43428 abgn (1x1:1 - id: 43428)
BUTTON: one reset button
LEDS : RGB-LED
MISC : Atmel AT24C64 8KiB EEPROM (i2c - seems empty)
: Ti INA219 26V, 12-bit, i2c output current/voltage/power monitor
: TPS23754, High Power/High Efficiency PoE Interface+DC/DC Controller
SERIAL:
WARNING: The serial port needs a TTL/RS-232 3V3 level converter!
The Serial setting is 115200-8-N-1. The board has a populated
right angle 1x4 0.1" pinheader.
The pinout is: VCC (next to J3, has little white arrow), RX, TX, GND.
This flashing procedure for the MR26 was tested with firmware:
"22-143410M-gf25cbf5a-asa".
U-Boot 2012.10-00063-g83f9fe4 (Jun 04 2014 - 21:22:39)
A guide how to open up the device is available on the wiki:
<https://openwrt.org/toh/meraki/mr26>
Notes:
- The WIFI do work to a degree. Limited to 802.11bg in the 2.4GHz band.
- the WIFI macs are made up.
0. Create a separate Ethernet LAN which can't have access to the internet.
Ideally use 192.168.1.2 for your PC. The new OpenWrt firmware will setup
the network via DHCP Discovery, so make sure your PC is running
a DHCP-Server (i.e.: dnsmasq)
'# dnsmasq -i eth# -F 192.168.1.5,192.168.1.50
Download the openwrt-meraki-mr26 initramfs file from openwrt.org and
rename it to something simple like mr26.bin. Then put it into the tftp's
server directory.
1. Disassemble the MR26 device by removing all screws (4 screws are located
under the 4 rubber feets!) and prying open the plastic covers without
breaking the plastic retention clips. Once inside, remove the plastic
back casing. Be careful, there some "hidden" retention clips on both
sides of the LAN port, you need a light to see those. Next, you want to
remove all the screws on the outer metal shielding to get to the PCB.
It's not necessary to remove the antennas!
2. Connect the serial cable to the serial header and Ethernet patch cable
to the device.
4. Before connecting the power, get ready flood the serial console program
with the magic: xyzzy . This is necessary in order to get into the
u-boot prompt. Once Ready: connect power cable.
5. If you don't get the "u-boot>" prompt within the first few seconds,
you have to disconnect and reconnect the power cable and try again.
6. In the u-boot prompt enter:
setenv ipaddr 192.168.1.4
setenv serverip 192.168.1.2
tftpboot ${meraki_loadaddr} mr26.bin; bootm
this will boot a in-ram-only OpenWrt image.
7. Once it booted use sysupgrade to permanently install OpenWrt.
To do this: Download the latest sysupgrade.bin file and move
it to the device. Then use sysupgrade *sysupgrade.bin to install it.
WARNING: DO NOT DELETE the "storage" ubi volume!
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The BDFs for the:
GL.iNet GL-B2200
were upstreamed to the ath10k-firmware repository
and landed in linux-firmware.git
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Kalle:
"I see that variant has a space in it, does that work it correctly? My
original idea was that spaces would not be allowed, but didn't realise
to add a check for that."
Is this an easy change? Because the original author (Tim Davis) noted:
"You may substitute the & and space with something else saner if they
prove to be problematic."
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
kernel linux now have 2 different export.h include, one from
linux/export.h and one from asm-generic/export.h
While most of our target user linux/export.h, aarch64 based target use
asm-generic/export.h that is not patched with the changes of
221-module_exports.
Patch also this additional header to fix multiple
aarch64-openwrt-linux-musl-ld: warning: orphan section `__ksymtab_strings' from `arch/arm64/kernel/head.o' being placed in section `__ksymtab_strings'
warning during kernel compilation.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
This patches does not have a valid patch headers and does not apply on
an external git tree with 'git am'. To fix this add the missing headers.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
This patches does not have a valid patch headers and does not apply on
an external git tree with 'git am'. To fix this add the missing headers.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
The amber and green wan led color was inverted in dts file, which ends
up leaving the wan led amber when the connection is established, so,
switch gpio led number (7 and 8) in qca9563_tplink_archer-c6-v2-us.dts.
Tip: the /etc/config/system file needs to be regenerated.
Signed-off-by: Rodrigo B. de Sousa Martins <rodrigo.sousa.577@gmail.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz> [commit subject]
Linux stable v5.15.51 brought commit 7a3a4683562e
("ARM: dts: bcm2711-rpi-400: Fix GPIO line names") which was already
part of a local patch which then failed to apply. Remove the already
applied and now failing hunk from the patch to fix the build.
Fixes: 552d76f2be ("kernel: bump 5.15 to 5.15.51")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
TechNexion PICO-PI-IMX7D is a NXP i.MX 7Dual based development board in
the well-known "Raspberry Pi" form factor, comprising of PICO-IMX7 SoM
and the PICO-PI-IMX7D carrier board.
Usually bundled with a 5" 800x480 LVDS display with I2C touchscreen and
an Omnivision OV5645 camera on a MIPI CSI bus, on a daughterboard. The
board was previously used primarily with "Android Things" ecosystem, but
the project was killed by Google.
This would not be possible, if not for the great tutorial of setting up
Debian on this board, by Robert C. Nelson [1].
Hardware highlights:
CPU: NXP i.MX 7Dual SoC, dual-core Cortex-A7 at 1000 MHz
RAM: 512 MiB DDR3 SDRAM
Storage: 4 GB eMMC
Networking:
- built-in Gigabit Ethernet with Atheros AR8035 PHY,
- Broadcom BCM4339 1x1 802.11ac Wi-Fi (over SDIO) + Bluetooth 4.1
(over SDIO + UART + IS2) combo, with Hirose u.FL connector on the
board,
- dual CAN interfaces on the 40-pin connector,
Interfaces:
- USB-C power input plus USB 2.0 OTG host/device port,
- single USB-A host port,
- serial console over built-in FT232BL USB-UART converter with
micro-USB connector (configuration: 115200-8-N-1),
- analog audio interface with TRRS connector in CTIA standard,
- SPI, I2C and UART interfaces available on the 40-pin,
- mikroBUS connector,
- I2C connector for the optional touch panel,
- parallel LCD output for the optional display,
- MIPI CSI connector for the optional camera
Installation:
1. Connect the serial console to debug USB connector and the terminal of
choice in another window, at 115200-8-N-1. Ensure you can switch to
it quickly after next step.
2. Power-on the board from your PC. Ensure your PC can supply required
current, the board can take more than 1 A in the peak load during
booting and brownout will result in power-on reset loop. Preferably,
use charging-capable USB port or connect through self-powered USB
hub. If U-Boot is present already on the eMMC, interrupt the booting
sequence by pressing any key and skip to point 7.
3. Ensure the boot mode jumpers J1 and J2 are in correct position for
USB recovery:
2 6 2 6
--------------
|o o-o||o-o o|
|o o-o||o-o o|
J1 -------------- J2
1 5 1 5
The jumpers are located just underneath the 40-pin expansion header
and are of the smaller 2 mm pitch.
4. Download and build 'imx_usb_loader' from:
https://github.com/boundarydevices/imx_usb_loader.
5. Power-on the board again from your PC through USB OTG connector.
6. Use 'imx_usb_loader' to load 'SPL' and 'u-boot-dtb.img' to the board:
$ sudo imx_usb u-boot-pico-pi-imx7d/SPL
$ sudo imx_usb u-boot-pico-pi-imx7d/u-boot-dtb.img
7. Switch to the terminal from step 2 and interrupt boot sequence by
pressing any key within 2 seconds.
8. Configure mmc 0 to boot from the data partition and disable access to
boot partitions:
=> mmc partconf 0 0 7 0
This only needs to be set once. If you were running Debian previously,
this is probably already set.
9. Enable USB mass storage passthrough for eMMC from U-boot
=> ums 0 mmc 0
10. Optionally, backup previous eMMC contents by reading out its image.
11. Copy over the factory image to the USB device, for example:
$ sudo dd if=openwrt-imx-cortexa7-pico-pi-imx7d-squashfs.combined.bin \
of=/dev/disk/by-id/usb-Linux_UMS_disk_0-0:0 \
bs=8M status=progress oflag=direct
12. Detach USB MSC interface from your PC and U-Boot by pressing Ctrl+C.
13. Ensure that boot mode jumpers are at the default settings for eMMC
boot:
2 6 2 6
--------------
|o-o o||o o-o|
|o-o o||o-o o|
J1 -------------- J2
1 5 1 5
If they are not, power-off the board, restore them and power-on the
board again. Otherwise, if jumpers are set, just reset the board from
U-Boot CLI:
=> reset
14. The installation is now complete and board should boot successfully.
Upgrading: just use sysupgrade image, as usual in OpenWrt.
Known issues/current limitations:
- OV5645 camera - not described in upstream device tree as of kernel
5.15. There are staging drivers present in upstream Linux tree for
i.MX 7 CSI, MIPI-CSI and video mux, and the configuration is there in
imx7s.dtsi - so this is expected to get supported eventually,
- on-chip ADCs are disabled in upstream device tree, so the kernel
driver remains disabled as well.
[1] https://forum.digikey.com/t/debian-getting-started-with-the-pico-pi-imx7/12429
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
[pepe2k@gmail.com: commit description reworded]
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Add OpenWrt specific aliases for system LED and label MAC device,
also set default serial console.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Ensure, that kernel update is performed atomically on filesystem, to
reduce likelihood of failure if power-cut occurs during sysupgrade. If
kernel update fails for whatever reason, skip updating rootfs as well.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Sysupgrade procedure for i.MX 6 Apalis boards is suitable for most other
i.MX boards booting from eMMC or SD card. Extract the common parts and
decouple the procedure from "apalis" board name in sysupgrade TAR
contents, so the procedure is reusable for i.MX 7 boards.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Most i.MX boards booting off eMMC or SD cards use raw U-Boot located at
69 kB offset from beginning of the device - create a recipe for such
image.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
The same combined image format can be used to boot both i.MX 6 and
i.MX 7 platforms - extract the common part.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
The PICO-PI-IMX7D board is equipped with external LCD display with
touchscreen. To allow displaying console on it, enable framebuffer,
fbcon and DRM support at early boot.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
[pepe2k@gmail.com: refreshed subtarget kernel config]
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Import sdma-imx7d.bin from linux-firmware repository at commit:
55edf5202154: ("imx: sdma: update firmware to v3.5/v4.5")
Cortex-A7 boards (i.MX 7 based) use different SDMA firmware than i.MX 6
boards - bundle the correct files in per-subtarget kernel options.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Add initial symbols required for i.MX 7 boards, based on devices
available on TechNexion PICO-PI-IMX7D board.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
[pepe2k@gmail.com: refreshed subtarget kernel config]
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Manual rebase by Marty Jones:
bcm27xx/patches-5.15/950-0078-BCM2708-Add-core-Device-Tree-support.patch
All other patches automatically rebased.
Signed-off-by: John Audia <therealgraysky@proton.me>
Signed-off-by: Marty Jones <mj8263788@gmail.com>
[Apply same changes to new dts entry in modified file]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
setup.c unconditionally sets the sys-led mode (blinking rate) to a
permanent high output. This may cause issues when a board expects this
pin to toggle periodically, e.g. when hooked up to an external watchdog.
If the sys-led peripheral is used to control an LED, the mux should be
configured to use the pin as GPIO0, allowing for better control as a
GPIO LED.
Signed-off-by: Sander Vanheule <sander@svanheule.net>
The devicetree for the ZyXEL XGS1250-12 was missing the description of
the front panel LED labeled "PWR SYS". Let's add it so it can be
controlled by the user.
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Like for RTL838x devices, add a pinctrl-single node to manage the
sys-led/gpio0 mux, and allow using the pin as GPIO.
Co-developed-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Not all devices using the gpio0/sys-led pin as a GPIO, configure the
pinmux. Add the necessary pinctrl properties to these devices to ensure
the pin is set up for use as GPIO.
Co-developed-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Tested-by: Bjørn Mork <bjorn@mork.no>
During upload of firmware images the WebUI and CLI patch process
extracts a version information from the uploaded file and stores it
onto the jffs2 partition. To be precise it is written into the
flash.txt or flash2.txt files depending on the selected target image.
This data is not used anywhere else. The current OpenWrt factory
image misses this label. Therefore version information shows only
garbage. Fix this.
Before:
DGS-1210-20> show firmware information
IMAGE ONE:
Version : xfo/QE~WQD"A\Scxq...
Size : 5505185 Bytes
After:
DGS-1210-20> show firmware information
IMAGE ONE:
Version : OpenWrt
Size : 5505200 Bytes
Tested-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Currently we build factory images only for DGS-1210-28 model. Relax
that constraint and take care about all models. Tested on DGS-1210-20
and should work on other models too because of common flash layout.
Tested-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Backport upstream solution that permits to declare nvmem cells with
dynamic partition defined by special parser.
This provide an OF node for NVMEM and connect it to the defined dynamic
partition.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
On the NanoPI R4S it takes an average of 3..5 seconds for the network devices
to appear in '/proc/interrupts'.
Wait up to 10 seconds to ensure that the distribution of the interrupts
really happens.
Signed-off-by: Ronny Kotzschmar <ro.ok@me.com>
On boot, kernel log complains no vbus supply is found:
`xhci-mtk 1a0c0000.usb: supply vbus not found, using dummy regulator`
so add the dts node entries to solve the issue
Signed-off-by: Andrew Sim <andrewsimz@gmail.com>
When building the mediatek/mt7629 target in OpenWrt 22.03 the kernel
does not have a configuration option for CONFIG_CRYPTO_DEV_MEDIATEK. Add
this option to the generic kernel configuration and also add two other
configuration options which are removed when we refresh the mt7629
kernel configuration.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
From now on we will insert CAMEO tags into sysupgrade images for
DGS-1210 devices. This will make the "OS:...FAILED" and "FS:...FAILED"
messages go away.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
The recent differentiation between v1 and v2 of the UniFi 6 LR added
support for the v2 version which has GPIO-controlled LEDs instead of
using an additional microcontroller to drive an RGB led.
The polarity of the white LED, however, was inverted and the default
states didn't make a lot of sense after all. Fix that.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The line trying to generate the standard sdcard.img.gz fails due to
boot.scr not being generated.
Remove the line in order to use the default sdcard.img.gz which is
exactly the same but includes generating the boot.scr file.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
napi_build_skb() reuses NAPI skbuff_head cache in order to save some
cycles on freeing/allocating skbuff_heads on every new Rx or completed
Tx.
Use napi_consume_skb() to feed the cache with skbuff_heads of completed
Tx so it's never empty.
Signed-off-by: Sieng Piaw Liew <liew.s.piaw@gmail.com>
[ fixed commit title ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
