The addresses were read from the 'config' partition, which would not always
contain the addresses at the same offsets, depending on the stock firmware
version used before flashing LEDE. Change this to get the addresses from
the 'product-info' partition, which is read-only.
Reported-and-tested-by: Andreas Ziegler <ml@andreas-ziegler.de>
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
ALFA Network AP121F is a pocket-size router dedicated for VPN/TOR users.
Device is based on Atheros AR9331 WiSoC and is running a custom version
(updated from OpenWrt CC to LEDE 17.01 release) of NetAidKit firmware.
Specification:
- 400/400/200 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR1)
- 16 MB of FLASH (SPI NOR)
- 1x 10/100 Mbps Ethernet
- 1T1R 2.4 GHz
- 1x microSD (optional, on separate PCB)
- 3x LED, 1x button, 1x switch
- UART header on PCB
Flash instruction (under U-Boot web recovery mode):
1. Configure PC with static IP 192.168.1.2/24.
2. Connect PC with RJ45 port, press the reset button, power up device,
wait for first blink of all LEDs (indicates network setup), then keep
button for 3 following blinks and release it.
3. Open 192.168.1.1 address in your browser and upload sysupgrade image.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Non-US versions of the TP-Link TL-WR710N v1 don't have a region code so
far, so we can just set US unconditionally.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
If nand chip has no NAND_NO_SUBPAGE_WRITE flag on its options
ubifs can't use it mtd devices and the kernel crashes with error:
__nand_correct_data: uncorrectable ECC error
Signed-off-by: Sergey Sergeev <adron@yapic.net>
This fixes wrong GPIO numbers for LEDs and button in Wallys DR344 board
and sets color of all LEDs to green as the mass production boards have
only green one.
Actually, DR344 has 6 GPIO-connected LEDs and one button:
- GPIO11: status
- GPIO12: sig1
- GPIO13: sig2
- GPIO14: sig3
- GPIO15: sig4
- GPIO16: reset button
- GPIO17: lan
WAN LED is connected directly with AR8035 PHY.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
This aligns default network interfaces configuration with vendor
firmware: GE (eth0) -> wan, FE (eth1) -> lan.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
GMAC0 interface of AR9344 SOC in Wallys DR344 board is connected with
AR8035, not with AR8327. Without this fix, GE interface doesn't work at
all or shows high packet loss ratio.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Bump the 17.01 tree kernel to 4.4.69. Trunk 4.4 and 17.01 4.4 have diverged, talked this
through with jow, he was okay with a clean diff against 17.01 and not a backported trunk
patch.
The following patches were applied upstream:
* 062-[1-6]-MIPS-* series
* 042-0004-mtd-bcm47xxpart-fix-parsing-first-block
Reintroduced lantiq/patches-4.4/0050-MIPS-Lantiq-Fix-cascaded-IRQ-setup, as
it was incorrectly included upstream thus dropped from LEDE, but subsequently
reverted upstream. Thanks to Kevin Darbyshire-Bryant for pointing me to it.
Compile-tested on: ar71xx, ramips/mt7621, x86/64.
Run-tested on: ar71xx, ramips/mt7621, x86/64.
Signed-off-by: Stijn Segers <francesco.borromini@inventati.org>
Fix a '==' that should be a '=' in a test condition. Busybox fortunately
doesn't care.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
This router has the same hardware as TP-LINK TL-WR841N/ND v11 (same FCC
ID, same TFTP image name...).
If the stock firmware web interface doesn't accept LEDE factory image,
it can be flashed via the U-Boot TFTP recovery mode, by long-pressing
the reset button after power on.
The TFTP image name is wr841nv11_tp_recovery.bin (yes, v11, not v12).
Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>
platform_find_rootfspart() fails if the kernel partition comes before the
rootfs partition. The proposed patch fixes this while preserving what I
understand was the original idea: stop at first match.
Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
The code that generates this image is broken in many ways.
The new code currently in master generates images that will not be compatible
with the ones in 17.01. To avoid a migration nightmare, this patch removes
image generation for this device in 17.01
Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
QCA956x is configured like AR934x, not like the older chips.
Should fix ethernet hangs when using the WAN port without SGMII
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The list of v2/v3 devices is getting longer and makes reading the names of
the profiles unnecessary hard.
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
Bump kernel to 4.4.44. Compile-tested on ar71xx, ramips/mt7621 and x86/64.
.44 has been run-tested on the 17.01 branch here on ar71xx and mt7621.
Signed-off-by: Stijn Segers <francesco.borromini@inventati.org>
(cherry picked from commit 20996edd68)
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Conflicts:
target/linux/ar71xx/patches-4.4/920-usb-chipidea-AR933x-platform-support.patch
target/linux/ar71xx/patches-4.4/930-chipidea-pullup.patch
The soft_config partition must be writeable for rbcfg to be able to
enact changes to the routerboot configuration.
The read-only flag was a mistake in the initial patch. Removing it
brings mach-rb941.c in line with all other RB platforms.
Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
Mikrotik RB411U has only one ethernet port - eth0. This patch allows to create
correct config with one lan section.
Signed-off-by: Cezary Jackiewicz <cezary@eko.one.pl>
Add full support for Mikrotik RB-941-2nD (hAP lite)
Original patch by Sergey Sergeev <adron@yapic.net> and
more information is available here:
https://wiki.openwrt.org/toh/mikrotik/rb941_2nd
I updated and adapted the patch to apply cleanly to LEDE trunk
and added proper numbering for the switch ports (matching case
labels).
Tested working on actual hardware with the information
provided in the above webpage. Sysupgrade works.
Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Remove the wget2nand script, drop the need for manual installation,
use sysupgrade instead.
There are now two different NAND images, one for 64 MiB flashes, the
other for >= 128 MiB
Signed-off-by: Felix Fietkau <nbd@nbd.name>
