Commit Graph

19287 Commits

Author SHA1 Message Date
Raylynn Knight
580723e86a realtek: add support for ZyXEL GS1900-16
The ZyXEL GS1900-16 is a 16 port gigabit switch similar to other GS1900 switches.

Specifications
--------------
* Device:    ZyXEL GS1900-16
* SoC:       Realtek RTL8382M 500 MHz MIPS 4KEc
* Flash:     16 MiB Macronix MX25L12835F
* RAM:       128 MiB DDR2 SDRAM Nanya NT5TU128M8HE
* Ethernet:  16x 10/100/1000 Mbps
* LEDs:      1 PWR LED (green, not configurable)
             1 SYS LED (green, configurable)
             16 ethernet port link/activity LEDs (green, SoC controlled)
* Buttons:   1 "RESET" button on front panel
* Power      120-240V AC C13
* UART:      1 serial header (J12) with populated standard pin connector on
             the right back of the PCB.
             Pinout (front to back):
             + Pin 1 - VCC marked with white dot
             + Pin 2 - RX
             + Pin 3 - TX
             + PIn 4 - GND

Serial connection parameters:  115200 8N1.

Installation
------------

OEM upgrade method:

* Log in to OEM management web interface
* Navigate to Maintenance > Firmware
* Select the HTTP radio button
* Select the Active radio button
* Use the browse button to locate the
realtek-generic-zyxel_gs1900-16-initramfs-kernel.bin
file amd select open so File Path is update with filename.
* Select the Apply button. Screen will display "Prepare
for firmware upgrade ...".
*Wait until screen shows "Do you really want to reboot?"
then select the OK button
* Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it:
   > sysupgrade -n /tmp/realtek-generic-zyxel_gs1900-16-squashfs-sysupgrade.bin
   it may be necessary to restart the network (/etc/init.d/network restart) on
   the running initramfs image.

U-Boot TFTP method:

* Configure your client with a static 192.168.1.x IP (e.g. 192.168.1.10).
* Set up a TFTP server on your client and make it serve the initramfs image.
* Connect serial, power up the switch, interrupt U-boot by hitting the
  space bar, and enable the network:
   > rtk network on
* Since the GS1900-16 is a dual-partition device, you want to keep the OEM
  firmware on the backup partition for the time being. OpenWrt can only boot
  from the first partition anyway (hardcoded in the DTS). To make sure we are
  manipulating the first partition, issue the following commands:
  > setsys bootpartition 0
  > savesys
* Download the image onto the device and boot from it:
   > tftpboot 0x84f00000 192.168.1.10:openwrt-realtek-generic-zyxel_gs1900-16-initramfs-kernel.bin
   > bootm
* Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it:
   > sysupgrade -n /tmp/openwrt-realtek-generic-zyxel_gs1900-16-squashfs-sysupgrade.bin
   it may be necessary to restart the network (/etc/init.d/network restart) on
   the running initramfs image.

Signed-off-by: Raylynn Knight <rayknight@me.com>
[removed duplicate patch title, align RAM specification]
Signed-off-by: Sander Vanheule <sander@svanheule.net>
2022-05-07 17:23:45 +02:00
Christian Lamparter
fd836f3d15 kernel: usb-xhci-pci-renesas: remove LINUX_5_10 dependency symbol
With 5.4 out of the picture, remove LINUX_5_10 here. This is
needed for the WNDR4700 as otherwise kmod-usb3 isn't available
for 5.15.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-05-07 16:26:21 +02:00
Christian Lamparter
c97c8b814a kernel/x86: move x86' specific watchdogs to the x86 target
upstream linux have these watchdogs locked behind X86.
These will not build on other architectures. So move them
to target/linux/x86/modules.mk

drivers/watchdog/Kconfig:

|config F71808E_WDT
|	tristate "Fintek F718xx, F818xx Super I/O Watchdog"
|	depends on X86
|[...]
|config IT87_WDT
|	tristate "IT87 Watchdog Timer"
|	depends on X86
|[...]
|config ITCO_WDT
|	tristate "Intel TCO Timer/Watchdog"
|	depends on (X86 || IA64) && PCI
|[...]
|config W83627HF_WDT
|	tristate "Watchdog timer for W83627HF/W83627DHG and compatibles"
|	depends on X86
|[...]

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-05-07 14:31:22 +02:00
Christian Lamparter
cb203adda0 kernel: provide i6300esb for qemu/libvirt
the Intel i6300esb is QEMU's default watchdog. And unlike
the real "Intel i6300ESB I/O Controller hub" hardware, the
i6300esb watchdog driver works on non-x86 targets like for
ARM (armvirt 32bit) and potentially virtual PowerPC and MIPS
targets (if there was any).

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-05-07 14:31:21 +02:00
Rodrigo Balerdi
f8b0010dfb ipq806x: add support for Arris TR4400 v2 / RAC2V1A
Hardware specs:
  SoC: Qualcomm IPQ8065 (dual core Cortex-A15)
  RAM: 512 MB DDR3
  Flash: 256 MB NAND, 32 MB NOR
  WiFi: QCA9983 2.4 GHz, QCA9984 5 GHz
  Switch: QCA8337
  Ethernet: 5x 10/100/1000 Mbit/s
  USB: 1x USB 3.0 Type-A
  Buttons: WPS, Reset
  Power: 12 VDC, 2.5 A

Ethernet ports:
  1x WAN: connected to eth2
  4x LAN: connected via the switch to eth0 and eth1
          (eth0 is disabled in OEM firmware)

MAC addresses (OEM and OpenWrt):
  fw_env @ 0x00  d4🆎82:??:??:?a  LAN (eth1)
  fw_env @ 0x06  d4🆎82:??:??:?b  WAN (eth2)
  fw_env @ 0x0c  d4🆎82:??:??:?c  WLAN 2.4 GHz (ath1)
  fw_env @ 0x12  d4🆎82:??:??:?d  WLAN 5 GHz (ath0)
  fw_env @ 0x18  d4🆎82:??:??:?e  OEM usage unknown (eth0 in OpenWrt)

  OID d4🆎82 is registered to:
  ARRIS Group, Inc., 6450 Sequence Drive, San Diego CA 92121, US

More info:
  https://openwrt.org/inbox/toh/arris/tr4400_v2

IMPORTANT:

This port requires moving the 'fw_env' partition prior to first boot to
consolidate 70% of the usable space in flash into a contiguous partition.
'fw_env' contains factory-programmed MAC addresses, SSIDs, and passwords.
Its contents must be copied to 'rootfs_1' prior to booting via initramfs.
Note that the stock 'fw_env' partition  will be wiped during sysupgrade.

A writable 'stock_fw_env' partition pointing to the old, stock location
is included in the port to help rolling back this change if desired.

Installation:

- Requires serial access and a TFTP server.
- Fully boot stock, press ENTER, type in:
mtd erase /dev/mtd21
dd if=/dev/mtd22 bs=128K count=1 | mtd write - /dev/mtd21
umount /config && ubidetach -m 23 && mtd erase /dev/mtd23
- Reboot and interrupt U-Boot by pressing a key, type in:
set mtdids 'nand0=nand0'
set mtdparts 'mtdparts=nand0:155M@0x6500000(mtd_ubi)'
set bootcmd 'ubi part mtd_ubi && ubi read 0x44000000 kernel && bootm'
env save
- Setup TFTP server serving initramfs image as 'recovery.bin', type in:
set ipaddr 192.168.1.1
set serverip 192.168.1.2
tftpboot recovery.bin && bootm
- Use sysupgrade to install squashfs image.

This port is based on work done by AmadeusGhost <amadeus@jmu.edu.cn>.

Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
[add 5.15 changes for 0069-arm-boot-add-dts-files.patch]
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2022-05-05 09:19:00 +09:00
Arınç ÜNAL
f4e219fd5e packages: nvram: add NVRAM quirks for bcm53xx target
Add NVRAM quirks script for the bcm53xx target. Split NVRAM quirks for the
bcm47xx and bcm53xx targets. Move clear partialboot NVRAM quirk for Linksys
EA9500 here. Add set wireless LED behaviour quirk for Asus RT-AC88U.

Use boot() instead of start() as nvram commands are meant to be executed
only once, at boot.

Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
2022-05-04 21:51:20 +02:00
Tiago Gaspar
65258f5d60 firewall: config: remove restictions on DHCPv6 allow rule
Remove restrictions on source and destination addresses, which aren't
specified on RFC8415, and for some reason in openwrt are configured
to allow both link-local and ULA addresses.
As cleared out in issue #5066 there are some ISPs that use Gloabal
Unicast addresses, so fix this rule to allow them.

Fixes: #5066

Signed-off-by: Tiago Gaspar <tiagogaspar8@gmail.com>
[rebase onto firewall3, clarify subject, bump PKG_RELEASE]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2022-05-04 15:26:16 +02:00
Jan Hoffmann
1daaef31b3 ltq-vdsl-app: disconnect when service is stopped
Stop the connection when the control daemon is terminated. The code is
a modified version of the termination routine in version 4.23.1 of the
daemon (which doesn't support VR9 modems anymore).

This could also be implemented by calling the acos and acs commands via
dsl_cpe_pipe.sh in the init script. However, doing it in the daemon
itself has the advantage of also working if it is terminated in another
way (for example during sysupgrade).

Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
2022-05-04 01:38:04 +01:00
Jan Hoffmann
db4bf4b968 ltq-vdsl/ltq-adsl: fix elapsed time calculation
The driver maintains elapsed times by repeatedly accumulating the time
since the previous update in a loop. For the elapsed showtime time, the
time difference is truncated to seconds before adding it, leading to a
sizable error over time.

Move the truncation to before calculation of the time difference in
order to remove this error. Also maintain the total elapsed time in the
same way in full seconds, to prevent the unsigned 32-bit counter from
wrapping around after about 50 days.

Testing on a VR9 device shows that the reported line uptime now matches
the actual elapsed wall time. The ADSL variant is only compile-tested,
but it should also work as the relevant code is identical.

Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
2022-05-04 01:38:04 +01:00
Jan Hoffmann
2f484aeff5 ltq-atm/ltq-ptm: avoid unnecessary build dependencies
Right now, both ltq-adsl-mei and ltq-vdsl-mei are always built, even
when they aren't necessary for the selected variant. This can cause the
build to fail, for example ltq-vdsl-mei doesn't build successfully here
on xway target due to the vectoring callback.

Make these dependencies conditional on the specific package variants,
so they are only built when actually needed.

Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
2022-05-04 01:38:04 +01:00
Daniel Golle
51c442c265
uqmi: update to git HEAD
56cb2d4 nas: add decoding of cell_id
 9a9019a uqmi: wms - added storage to read text messages

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-05-04 01:33:21 +01:00
Daniel Golle
4509b790f0
fstools: update to git HEAD
9e11b37 fstools: remove SELinux restorecon hack

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-05-03 02:11:17 +01:00
Daniel Golle
fb01111866
procd: update to git HEAD
652e6df init: restore SELinux labels after policy is loaded

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-05-03 02:11:12 +01:00
Daniel Golle
7b07c3cff5
base-files: simplify restorecon logic
Remove forgotten redundant selinuxenabled call and skip the whole
thing in case $IPKG_INSTROOT is set as labels are anyway applied only
later on in fakeroot when squashfs is created.

Fixes: 6d7272852e ("base-files: add missing $IPKG_INSTROOT to restorecon call")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-05-02 21:11:05 +01:00
Dominick Grift
4379457098 selinux-policy: update to version 1.1
try to clean up some labeling inconsistencies
iwinfo loose ends
ucode loose ends
Makefile: adjust mintesttgt (adds blockmount/blockd)
nftables: reads inherited netifd pipe
ucode: reads inherited netifd pipes
mountroot: fowner
sandbox: writes inherited dropbear pipes
unbound related to /tmp/etc/ssl
unbound loose ends
adds a sslconftmpfile for /tmp/etc/ssl
README: maintain a wish list in the README
iwinfo: netifd forgot write
gptfdisk loose ends
iwinfo: netifd wpad reads/writes inherited netifd fifo files
netifd (mac80211.sh) executes iwinfo
luci: executes wireguard
luci-cgi: audits xtables execute access
rcuhttpd: lists ssl certfile dirs
iwinfo, wifi,nftables usage of ttyd pty if available
urandomseed: seedrng needs cap_sys_admin
iwinfo iwinfo, nftables and some chronyd rules related to ntp nts server
nftables, wifi and adds iwinfo skel
nftables, rpcd, ucode
nftables, ucode and seedrng ucode, fw3/nftables, luci
adds ucode skel and some fw3/nftables related
urandomseed: some seedrng rules
fw3 adds some support for fw4
urandomseed: /etc/seedrng is for seed.credit
hotplugcal: runs ucode which is interpreter like
adds a nftables skeleton and makes xtables optional
agent: allow all agents to write inherited dropbear pipes
urandomseed: this seems to be replaced by seedrng
kmodloader: label /etc/modules.conf kmodloader.conffile
Revert "shelexecfile: remove auditallow rule"
Makefile: sort the modules to process by secilc
Moves back to git.defensec.nl
unbound odhcpd (ip) reads net proc
tcp dump
shelexecfile: remove auditallow rule
rrd.cil: fixes indent
Target rddtool from cgi-io instead of runnit it without transition
rrd.cil related
rrd, rpcd, cgiio clean ups related to luci-app-statistics
Rules for rrd files and luci-statistics
unboundcontrol ordering
Several missing permissions
blockmount, dnsmasq, hotplugcall, rpcd, unbound
adds mctp_socket (linux 5.15)
ip: forgot tc-tiny type transition to go along with the fc spec
ip: adds a fc spec for tc-tiny (called by sqm)
adds ttyACM fc spec and various assorted loose ends
.gitattributes: do not export the github workflows
workflow use selinux 3.3

project moved back to https://git.defensec.nl/selinux-policy.git

Signed-off-by: Dominick Grift <dominick.grift@defensec.nl>
2022-05-02 21:10:43 +01:00
Enrico Mioso
e3f9af4fb6 ipq40xx: fix BDF file for pcie wifi chip on the GL.Inet GL-B2200
After the switch to pre-calibration, ath10k would fail to initialize
the PCIE Wi-Fi on the GL-B200 as follows:

ath10k_pci 0000:01:00.0: enabling device (0140 -> 0142)
ath10k_pci 0000:01:00.0: qca9888 hw2.0 target 0x01000000 chip_id 0x00000000 sub 0000:0000
[...]
ath10k_pci 0000:01:00.0: failed to fetch board data for bus=pci,bmi-chip-id=0,bmi-board-id=16,variant=GL-B2200 from ath10k/QCA9888/hw2.0/board-2.bin
ath10k_pci 0000:01:00.0: failed to fetch board-2.bin or board.bin from ath10k/QCA9888/hw2.0
ath10k_pci 0000:01:00.0: failed to fetch board file: -12
ath10k_pci 0000:01:00.0: could not probe fw (-12)

Repackage the BDF file after renaming relevant fields and files to
allow for the Wi-Fi interface to start again.

Fixes: 80d34d9d59 ("ipq40xx: document pcie wifi chip on the GL.Inet GL-B2200")
CC: Christian Lamparter <chunkeey@gmail.com>
CC: Robert Marko <robimarko@gmail.com>
Reviewed-by: Robert Marko <robert.marko@sartura.hr>
Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
2022-05-02 21:16:14 +02:00
Daniel Golle
6d7272852e
base-files: add missing $IPKG_INSTROOT to restorecon call
Update to overlooked v2 version of Dominick Grift's patch.

Fixes: 5109bd164c ("base-files: address sed in-place without SELinux awareness")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-05-02 19:59:58 +01:00
Bruno Victal
0276fab649 dnsmasq: fix jail_mount for serversfile
Fix 'serversfile' option not being jail_mounted by the init script.

Signed-off-by: Bruno Victal <brunovictal@outlook.com>
2022-05-02 18:57:49 +01:00
Dominick Grift
5109bd164c
base-files: address sed in-place without SELinux awareness
sed(1) in busybox does not support this functionality:
https://git.savannah.gnu.org/cgit/sed.git/tree/sed/execute.c#n598

This causes /etc/group to become mislabeled when a package requests
that a uid/gid be added on OpenWrt with SELinux

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
[move restorecon inside lock]
Signed-off-by: Dominick Grift <dominick.grift@defensec.nl>
2022-05-02 18:56:02 +01:00
Rodrigo Balerdi
7d02fc0951 base-files: fix sysupgrade for kernel-out-of-UBI
Commit ecbcc0b595 bricks devices on which the raw kernel and UBI mtd
partitions overlap.

This is the case of the ZyXEL NR7101 for example. Its OEM bootloader has
no UBI support. OpenWrt splits the stock kernel mtd partition into a raw
kernel part used by the bootloader and a UBI part used to store rootfs
and rootfs_data. Running mtd erase on the complete partition during
sysupgrade erases the UBI part and results in a soft brick.

Arguably the best solution would be to fix the partition layouts so that
kernel and UBI partitions do not overlap, also including a stock_kernel
partition to help reverting to stock firmware. This would have the added
benefit of protecting UBI from kernel images that are excessively large.

Fixes: ecbcc0b595 ("base-files: safer sysupgrade.tar for kernel-out-of-UBI")
Reported-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
2022-05-02 12:42:15 +01:00
Daniel Golle
4e8d095013
fstools: update to git HEAD
f0fc66a libfstools: check for overlay mounting errors
 128ecaf Update / fix extroot comments
 8a0ba3b libfstools: get rid of "extroot_prefix" global variable
 649cd3f libfstools: use variable for overlay mount-point
 922f1b3 libfstools: avoid segfault in find_mount_point
 ce5eacb libfstools: mtd: improve error handling
 898b328 blockd: restore device_move semantics
 0917d22 block: don't probe mtdblock on NAND (with legacy exceptions)

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-05-01 17:02:39 +01:00
Nick Hainke
ab4eafbed9 mdadm: update to 4.2
Refreshed patches:
- 100-cross_compile.patch

Manually refreshed patches:
- 200-reduce_size.patch

Removed patches:
- 101-mdadm.h-Undefine-dprintf-before-redefining.patch
- 102-Add-missing-include-file-sys-sysmacros.h.patch

Changes:

 e30ca260 Release mdadm-4.2
 8c80d305 Monitor: print message before quit for no array to monitor
 ced5fa8b mdadm: block creation with long names
 b71de056 Correct checking if file descriptors are valid
 b2e4f084 Incremental: Close unclosed mdfd in IncrementalScan()
 195d1d76 imsm: assert if there is migration but prev_map doesn't exist
 75f3ba25 imsm: free allocated memory in imsm_fix_size_mismatch
 bce0eab3 Release mdadm-4.2-rc3
 4389ce73 imsm: introduce helpers to manage file descriptors
 8e1a258e mdadm/Detail: Can't show container name correctly when unpluging disks
 a35aa68f mdadm/lib: Define a new helper function is_dev_alived
 1c66260d Fix 2 dc stream buffer
 d64a37b9 Assemble: apply sysfs rules
 5f6dedfb Fix potential overlap dest buffer
 a0422106 disallow create or grow clustered bitmap with writemostly set
 cf16a350 Fix buffer size warning for strcpy
 60815698 Refactor parse_num and use it to parse optarg.
 f7889e51 Fix error message when creating raid 4, 5 and 10
 54604768 mdadm: fix coredump of mdadm --monitor -r
 feeb2785 Utils: Change sprintf to snprintf
 b8bbf264 Release mdadm-4.2-rc2
 e6878148 Assemble: skip devices that don't match uuid instead of aborting the assembly.
 0663137c Add monitor delay parameter to mdadm.conf
 2b2c5668 tests: Avoid passing chunk size when creating RAID 1
 7d374a18 Fix memory leak after "mdadm --detail"
 92a647c8 Assemble: start dirty and degraded array.
 1c275381 imsm: fix num_data_stripes after raid0 takeover
 5b30a34a Add error handling for chunk size in RAID1
 3a85bf0e imsm: Fix possible memory leaks and refactor freeing struct dl
 ccd61ebf mdadm: Fix building errors
 601ffa78 Don't associate spares with other arrays during RAID Examine
 8d69bf14 Remove Spare drives line from details for external metadata
 7d8935cb imsm: correct offset for 4k disks in --examine output
 dca80fcd Use dev_open in validate geometry container
 f421731c mdadm/super1: It needs to specify int32 for bitmap_offset
 1f5d54a0 Manage: Call validate_geometry when adding drive to external container
 8662f92d imsm: Limit support to the lowest namespace
 fcebeb77 imsm: add devpath_to_char method
 7c798f87 imsm: add generic method to resolve "device" links
 0530e2e0 Prevent user from using --stop with ambiguous args
 83b3de77 Fix some building errors
 ff904202 imsm: change wrong size verification
 c11b1c3c Release mdadm-4.2-rc1
 aec01630 super-intel.c: Handle errors from calls to get_dev_sector_size()
 78c93b00 mdadm: fix growing containers
 af3396da Monitor: make libudev dependency optional
 f94df5cf imsm: support for third Sata controller
 d835518b imsm: nvme multipath support
 4036e7ee imsm: extend curr_migr_unit to u64
 bdbe7f81 Grow: Block reshape when external metadata and write-intent bitmap
 848d71c9 Create: Block automatic enabling bitmap for external metadata
 19ad203e imsm: Update-subarray for write-intent bitmap
 dc95f821 Add "bitmap" to allowed command-line values
 69d40de4 imsm: Adding a spare to an existing array with bitmap
 fbc42556 imsm: Write-intent bitmap support
 b554ab5c Enable bitmap support for external metadata
 b090e910 Modify mdstat parsing for volumes with the bitmap
 db537788 It should be FAILED when raid has not enough active disks
 c7b8547c imsm: add verbose flag to compare_super
 49b69533 mdmonitor: check if udev has finished events processing
 0d583954 Document PPL in man md
 2f86fda3 imsm: use saved fds during migration
 f7a6246b super1.c: avoid useless sync when bitmap switches from clustered to none
 e6561c4d super1: fix Floating point exception
 8818d4e7 Grow: be careful of corrupt dev_roles list
 4ae96c80 mdadm: fix reshape from RAID5 to RAID6 with backup file
 1fe2e100 mdadm/bitmap: locate bitmap calcuate bitmap position wrongly
 75562b57 Dump: get stat from a wrong metadata file when restoring metadata
 69068584 Incremental: Remove redundant spare movement logic
 a64f1263 udev: start grow service automatically
 b4a5ad49 Make target to install binaries only
 9c030dad mdadm/Detail: show correct state for clustered array
 ff6bb131 mdadm: Unify forks behaviour
 a8f3cfd5 imsm: limit support to first NVMe namespace
 ca4b156b Monitor: don't use default modes when creating a file
 b65c1f4a imsm: remove redundant calls to imsm_get_map
 895ffd99 imsm: update num_data_stripes according to dev_size
 ce559078 Create.c: close mdfd and generate uevent
 c3129b39 Detail: fix segfault during IMSM raid creation
 97b51a2c Super1: allow RAID0 layout setting to be removed.
 7f3b2d1d Check if other Monitor instance running before fork.
 cab9c67d mdmonitor: set small delay once
 007087d0 Monitor: stop notifing about containers.
 e2308733 Monitor: refresh mdstat fd after select
 2ce09172 Don't create bitmap for raid5 with journal disk
 64bf4dff Detail: show correct raid level when the array is inactive
 5f418455 manual: update --examine-badblocks
 5e592e1e mdadm/md.4: update path to in-kernel-tree documentation
 138a9e9b Specify nodes number when updating cluster nodes
 77b72fa8 mdadm/Grow: prevent md's fd from being occupied during delayed time
 bcf40dbb Update link to Intel page for IMSM
 8e41153c Use more secure HTTPS URLs
 2cf04330 Detect too-small device: error rather than underflow/crash
 7758ada9 Block overwriting existing links while manual assembly
 d92cee7b restripe: fix ignoring return value of ‘read’ and lseek
 7d90f760 Include count for \0 character when using strncpy to implement strdup.
 f4c8a605 uuid.c: split uuid stuffs from util.c
 03ab9763 Makefile: add EXTRAVERSION support
 3b7aae92 mdcheck: Log when done
 7b99edab Assemble.c: respect force flag.
 ec7d7cee clean up meaning of small typo
 5cfb79de Assemble: print error message if mdadm fails assembling with --uuid option
 12724c01 Manage, imsm: Write metadata before add
 1c294b5d Detail: adding sync status for cluster device
 185ec439 Monitor: improve check_one_sharer() for checking duplicated process
 e1b92ee0 udev: Ignore change event for imsm
 ba1b3bc8 imsm: show Subarray and Volume ID in --examine output
 e48aed3c imsm: support the Array Creation Time field in metadata
 9e449405 Detail: show correct bitmap info for cluster raid device
 06a6101c imsm: Correct minimal device size.
 45c43276 imsm: Remove --dump/--restore implementation
 3364781b imsm: pass subarray id to kill_subarray function
 fd38b8ea Remove the legacy whitespace
 2551061c mdadm.8: add note information for raid0 growing operation
 1e93d0d1 imsm: fill working_disks according to metadata.
 42e641ab Add support for Tebibytes
 4431efeb imsm: Update grow manual.
 e1512e7b mdcheck service can't start succesfully because of syntax error
 1a874930 Change warning message
 aced6fc9 Respect $(CROSS_COMPILE) when $(CC) is the default
 027c099f Assemble: add support for RAID0 layouts.
 329dfc28 Create: add support for RAID0 layouts.
 6da53c0e imsm: Change the way of printing nvme drives in detail-platform.
 b771faef imsm: return correct uuid for volume in detail
 4b31846f Remove unused code
 9cf361f8 Fix up a few formatting issues
 02af3793 Remove last traces of HOT_ADD_DISK
 1cc3965d Manage: Remove the legacy code for md driver prior to 0.90.03
 761e3bd9 super-intel: don't mark structs 'packed' unnecessarily
 85b83a79 SUSE-mdadm_env.sh: handle MDADM_CHECK_DURATION
 4ca799c5 mdcheck: use ${} to pass variable to mdcheck
 6636788a mdcheck: when mdcheck_start is enabled, enable mdcheck_continue too.
 1a1ced1e imsm: allow to specify second volume size
 b6180160 imsm: save current_vol number
 7bd59e79 udev: allow for udev attribute reading bug.
 61109314 Don't need to check recovery after re-add when no I/O writes to raid
 8063fd0f Init devlist as an array
 e53cb968 mdadm/md.4: add the descriptions for bitmap sysfs nodes
 2c2d9c48 mdadm: force a uuid swap on big endian
 43ebc910 mdadm: Introduce new array state 'broken' for raid0/linear
 fd5b09c9 mdadm: check value returned by snprintf against errors
 91c97c54 imsm: close removed drive fd.
 1a52f1fc udev: add --no-devices option for calling 'mdadm --detail'
 d11abe4b mdadm: add --no-devices to avoid component devices detail information
 452dc4d1 mdadm.h: include sysmacros.h unconditionally
 b0681598 mdadm: load default sysfs attributes after assemblation
 486720e0 super-intel: Use put_unaligned in split_ull
 7039d1f8 mdadm.h: Introduced unaligned {get,put}_unaligned{16,32}()
 a4f7290c super-intel: Fix issue with abs() being irrelevant
 4ec389e3 Enable probe_roms to scan more than 6 roms.
 ae7d61e3 mdmon: fix wrong array state when disk fails during mdmon startup
 3c9b46cf udev: Add udev rules to create by-partuuid for md device
 22dc741f Create: Block rounding size to max
 05501181 imsm: fix spare activation for old matrix arrays
 227aeaa8 add missing units to --examine
 2b57e4fe Assemble: Fix starting array with initial reshape checkpoint
 d2e11da4 mdmon: wait for previous mdmon to exit during takeover
 69d08478 mdmon: don't attempt to manage new arrays when terminating
 76b906d2 mdadm/tests: add one test case for failfast of raid1
 cab114c5 Fix reshape for decreasing data offset
 e3615ecb Detail.c: do not skip first character when calling xstrdup in Detail()
 ebf3be99 Fix spelling typos.
 9f421827 imsm: fix reshape for >2TB drives
 a4e96fd8 imsm: finish recovery when drive with rebuild fails
 757e5543 policy.c: Fix for compiler error
 467e6a1b policy.c: prevent NULL pointer referencing
 76d505de Grow: report correct new chunk size.
 085df422 Grow: avoid overflow in compute_backup_blocks()
 563ac108 Assemble: mask FAILFAST and WRITEMOSTLY flags when finding the most recent device
 d7a1fda2 imsm: update metadata correctly while raid10 double degradation
 7cd7e91a Monitor: add system timer to run --oneshot periodically
 4199d3c6 mdcheck: add systemd unit files to run mdcheck.
 cd72f9d1 policy: support devices with multiple paths.
 6b611284 Document PART-POLICY lines
 0833f9c3 Assemble: keep MD_DISK_FAILFAST and MD_DISK_WRITEMOSTLY flag

Signed-off-by: Nick Hainke <vincent@systemli.org>
2022-05-01 00:42:30 +02:00
Kerma Gérald
1aac1b36d3 f2fs-tools: fix resize.f2fs (#9800)
resolve issue
- https://github.com/openwrt/openwrt/issues/9800
add the upstream patch:
- f2fs-tools.git/patch/?id=f056fbeff08d30a6d9acdb9e06704461ceee3500

Signed-off-by: Kerma Gérald <gandalf@gk2.net>
2022-05-01 00:42:30 +02:00
Josef Schlehofer
4f51f1fc9b uboot-mvebu: update to version v2022.04
Release announcement:
https://lore.kernel.org/u-boot/20220404143253.GQ14476@bill-the-cat/

Release notes between tags:
https://source.denx.de/u-boot/u-boot/-/compare/v2022.01...v2022.04?from_project_id=531

All patches were removed, since they are included in this release.

Run tested: Turris Omnia, mvebu/cortex-a9, OpenWrt daily snapshots

Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
2022-05-01 00:42:30 +02:00
Josef Schlehofer
69cef74c67 uboot-mvebu: remove enabled CONFIG_CMD_SETEXPR
We don't need to make sure that we want to have enabled
CONFIG_CMD_SETEXPR by default, since this is already done in U-boot [1].
This was actually needed only for clearfog board [2], which was added in
commit: da0005a6d08ae33d958a6d8a6c0c12dc07b5b2b8 ("uboot-mvebu: add
patch to enable setexpr for clearfog boards) and send to U-boot to fix
it properly. After a while, there was added support for Turris Omnia,
which uses setexpr as well [3], but for this board, there are no fixes
needed in U-boot and that's why we can remove this option here.

It is helpful with shell scripting. If some downstream distributions are
using it, they should correct it in defconfig for related boards.

[1] e95afa5675/cmd/Kconfig (L1504)

[2] 852126680e/target/linux/mvebu/image/clearfog.bootscript (L7)

[3] 852126680e/target/linux/mvebu/image/turris-omnia.bootscript (L2)

Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
2022-05-01 00:42:30 +02:00
Josef Schlehofer
b3c2072504 uboot-mvebu: add patch to enable setexpr for clearfog boards
Option CMD_SETEXPR is already default in U-boot [1], since this was
disabled since initial version for this board, there is send this
	patch to U-boot mailing list to enable it.

It is required to use in OpenWrt bootscript for these boards [2].

[1] e95afa5675/cmd/Kconfig (L1504)

[2] 852126680e/target/linux/mvebu/image/clearfog.bootscript (L7)

Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
2022-05-01 00:42:30 +02:00
Jo-Philipp Wich
573ce80ca6 ucode: reorder BuildPackage calls
Ensure that the libucode recipe is processed before the ucode one in
order to reliably encode the ABI version into ucode's libucode dependency.

Fixes: #9788
Ref: https://forum.openwrt.org/t/fw4-wont-start-after-upgrade/126308
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2022-04-28 10:43:44 +02:00
David Bauer
f757a8a098 iwinfo: update to latest HEAD
dc6847e iwinfo: nl80211: omit A-hwmode on non-5GHz hardware

Signed-off-by: David Bauer <mail@david-bauer.net>
2022-04-27 00:54:24 +02:00
Hans Dedecker
432a25db72 nat46: update to git HEAD
95ca1c3 nat46-core: ignore IPv4 options when translating packets
39778c2 add a module argument to ignore TOS translate for IPv4
9a36ee1 add a module argument to ignore TOS translate for IPv4
79190a8 add a module argument to ignore TOS translate for IPv4

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
2022-04-26 22:41:57 +02:00
David Bauer
fb7ff6b027 uboot-envtools: add WS-AP3825i config
Add configuration to use uboot-envtools with the Extreme Networks
WS-AP3825i.

Signed-off-by: David Bauer <mail@david-bauer.net>
2022-04-26 00:57:22 +02:00
Daniel Golle
2b5fa44f60
dnsmasq: add logfacility file to jail mounts
If logfacility is a path to a file it needs to be r/w mounted in the
sandbox as well for dnsmasq to work.

Reported-by: @iointerrupt
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-04-25 19:28:12 +01:00
David Bauer
46980294f6 iwinfo: update to latest HEAD
a479b9b devices: remove whitespace
562d015 iwinfo: nl80211: fix hwmode parsing for multi-band NICs

Signed-off-by: David Bauer <mail@david-bauer.net>
2022-04-24 23:09:51 +02:00
Clemens Hopfer
4891b86538 ramips: add support for YunCore AX820/HWAP-AX820
There are two versions which are identical apart from the enclosure:
  YunCore AX820: indoor ceiling mount AP with integrated antennas
  YunCore HWAP-AX820: outdoor enclosure with external (N) connectors

Hardware specs:
  SoC: MediaTek MT7621DAT
  Flash: 16 MiB SPI NOR
  RAM: 128MiB (DDR3, integrated)
  WiFi: MT7905DAN+MT7975DN 2.4/5GHz 2T2R 802.11ax
  Ethernet: 10/100/1000 Mbps x2 (WAN/PoE+LAN)
  LED: Status (green)
  Button: Reset
  Power: 802.11af/at PoE; DC 12V,1A
  Antennas: AX820(indoor): 4dBi internal; HWAP-AX820(outdoor): external

Flash instructions:
  The "OpenWRT support" version of the AX820 comes with a LEDE-based
  firmware with proprietary MTK drivers and a luci webinterface and
  ssh accessible under 192.168.1.1 on LAN; user root, no password.
  The sysupgrade.bin can be flashed using luci or sysupgrade via ssh,
  you will have to force the upgrade due to a different factory name.
  Remember: Do *not* preserve factory configuration!

MAC addresses as used by OEM firmware:
  use   address            source
  2g    44:D1:FA:*:0b      Factory 0x0004 (label)
  5g    46:D1:FA:*:0b      LAA of 2g
  lan   44:D1:FA:*:0c      Factory 0xe000
  wan   44:D1:FA:*:0d      Factory 0xe000 + 1
The wan MAC can also be found in 0xe006 but is not used by OEM dtb.

Due to different MAC handling in mt76 the LAA derived from lan is used
for 2g to prevent duplicate MACs when creating multiple interfaces.

Signed-off-by: Clemens Hopfer <openwrt@wireloss.net>
2022-04-23 20:46:25 +02:00
Felix Fietkau
fb4edcef71 mt76: update to the latest version
a666d5637bc3 mt76: fix tx status related use-after-free race on station removal

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-04-23 15:50:38 +02:00
Jo-Philipp Wich
c59704334c ucode: fix PKG_MIRROR_HASH
Fixes: 0400774a10 ("ucode: update to latest Git HEAD")
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2022-04-22 09:23:49 +02:00
Jo-Philipp Wich
af02a12d7c firewall4: update to latest Git HEAD
fc83d46 ruleset: set auto-merge directive for interval sets
9bce873 fw4: fix skipping invalid ipset entries
425ea8a fw4: fix applying zone flags for source bound rules

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2022-04-22 00:50:36 +02:00
Jo-Philipp Wich
0400774a10 ucode: update to latest Git HEAD
e14b099 syntax: implement support for ES6 template literals
111cf06 vm: stop executing bytecode on return of nested calls

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2022-04-22 00:50:36 +02:00
Felix Fietkau
0d2d52df69 mt76: update to the latest version
d4937118ec4f mt76: fix rx reordering with non explicit / psmp ack policy
f50672518bcc mt76: do not attempt to reorder received 802.3 packets without agg session
75e046e3c9ae mt76: fix antenna config missing in 6G cap
64ede85f14b5 mt76: mt7915: remove SCS feature
db0a67582028 mt76: mt7915: make read-only array ppet16_ppet8_ru3_ru0 static const
68a2f68d5c01 mt76: mt7921: make read-only array ppet16_ppet8_ru3_ru0 static const
1e7b77294e97 mt76: mt7921: fix kernel crash at mt7921_pci_remove
795830a99a6c mt76: mt7915: add debugfs knob for RF registers read/write
60a8ec12a8eb mt76: mt7603: move spin_lock_bh() to spin_lock()
5ec7a2eac867 mt76: mt7915: disable RX_HDR_TRANS_SHORT
eecbb4992073 mt76: fix encap offload ethernet type check

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-04-20 18:14:08 +02:00
Daniel Golle
079828fa54
uboot-mediatek: replace patch with accepted commit
Replace pending patch with version accepted upstream.
Other than in the first suggested version, the new property is now
called 'u-boot,bootconf' instead of 'bootconf'.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-04-20 15:22:45 +01:00
Eneas U de Queiroz
c18c6e53b9 wolfssl: fix compilation with /dev/crypto
This is trivial fix of a duplicate definition of 'int ret'.

Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
2022-04-20 12:36:38 +02:00
Daniel Golle
810b48e793
uboot-mediatek: remove '0x' prefix from pstore node
Remove '0x' prefix from pstore node in dts, just like it was done
for the device tree used by Linux on MT7622.
This change is done in preparation to update U-Boot to 2022.04.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-04-19 17:07:38 +01:00
Rodrigo Balerdi
9ba28f978c base-files: minimize critical time in sysupgrade
Attempt to minimize the time during which an interrupted nand sysupgrade
can lead to a non-functional device by flushing caches before starting
the upgrade procedure.

Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
2022-04-19 16:28:25 +01:00
Rodrigo Balerdi
9a2f08f6e7 base-files: trim unnecessary nand sysupgrade code
Remove unnecessary sync commands during nand sysupgrade.

Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
2022-04-19 16:28:25 +01:00
Rodrigo Balerdi
bfd9afc38d base-files: fix issues in nand sysupgrade
Fix issues while retaining configuration during nand sysupgrade:
- abort configuration saving if data partition is not found
- generate diagnostics if saving fails (eg, because of lack of space)
- do not output "sysupgrade successful" in case of errors

Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
2022-04-19 16:28:25 +01:00
Rodrigo Balerdi
f8351d65bb base-files: clean up nand sysupgrade code
Fix some inconsistent quoting in nand sysupgrade code.

Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
2022-04-19 16:28:25 +01:00
Rodrigo Balerdi
de4b65a793 base-files: clean up ubinized sysupgrade code
Remove redundant check from nand ubinized sysupgrade code. This check
has already been done in the only caller of the affected function:
nand_do_upgrade.

Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
2022-04-19 16:28:25 +01:00
Rodrigo Balerdi
264d948302 base-files: clean up nand tar sysupgrade code
Prepares code for ubirename-based safe sysupgrade implementation.

Fixes several issues:
- the special CI_KERNPART value "none" is ignored if an MTD partition
  named "none" exists
- misleading variable names (such as has_kernel to mean "tar has kernel
  and it should not be written to an MTD partition but a UBI volume")
- inconsistent treatment of zero-length tar member files
- inconsistent meaning of "0" and "" variable values
- redundant operations (unneeded untaring, repeated untaring, unneeded
  partition lookups)
- inconsistent variable quoting

Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
2022-04-19 16:28:25 +01:00
Rodrigo Balerdi
ecbcc0b595 base-files: safer sysupgrade.tar for kernel-out-of-UBI
Ensure that the kernel CRC is invalidated while rootfs is being updated.
This allows the bootloader to detect an interrupted sysupgrade and fall
back to an alternate booting method, such as TFTP, instead of just going
ahead with normal boot and effectively bricking the device.

Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
2022-04-19 16:28:25 +01:00
Rodrigo Balerdi
073dc450b5 base-files: safer sysupgrade for kernel-in-UBI devices
Ensure that the kernel CRC is invalidated while rootfs is being updated.
This allows the bootloader to detect an interrupted sysupgrade and fall
back to an alternate booting method, instead of just going ahead with
normal boot and effectively bricking the device.

Possible fallbacks include a recovery initramfs partition or UBI volume
and TFTP. See here for an example U-Boot configuration with fallbacks:
https://shorturl.at/befsA (https://github.com/Lanchon/openwrt-tr4400-v2/
blob/e7d707d6bd7839fbd0b8d0bd180fce451df77e47/install-recovery.sh#L52-L63)

Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
2022-04-19 16:28:25 +01:00
Rodrigo Balerdi
1e191adb20 base-files: fix nand sysupgrade comments
Erroneous comments possibly applied to an earlier code revision.

Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
2022-04-19 16:28:25 +01:00
Rodrigo Balerdi
e3238a486f base-files: improve sysupgrade ubiblock handling
Only remove ubiblock devices required for nand sysupgrade.

Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
2022-04-19 16:28:25 +01:00
Rodrigo Balerdi
f5ed603d0c base-files: emit diagnostics on sysupgrade abort
Emit diagnostics if nand sysupgrade is aborted because UBI partition
cannot be attached. Also avoid redudndant checks.

Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
2022-04-19 16:28:25 +01:00
Thibaut VARÈNE
7dc52a78ae mac80211: fix QCA9561 PA bias
This patch fixes an invalid TX PA DC bias level on QCA9561, which
results in a very low output power and very low throughput as devices
are further away from the AP (compared to other 2.4GHz APs),
following a suggestion from nbd[1].

This patch has been submitted upstream[2].

[1] https://lore.kernel.org/all/91c58969-c60e-2f41-00ac-737786d435ae@nbd.name
[2] https://lore.kernel.org/linux-wireless/20220417145145.1847-1-hacks+kernel@slashdirt.org/

Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
2022-04-18 06:40:59 +02:00
Hauke Mehrtens
54d9051c55 linux-firmware: Update to version 20220411
The following files used in OpenWrt changed:
 amd64-microcode/lib/firmware/amd-ucode/microcode_amd_fam17h.bin
 amd64-microcode/lib/firmware/amd-ucode/microcode_amd_fam19h.bin
 amdgpu-firmware/lib/firmware/amdgpu/aldebaran_mec.bin
 amdgpu-firmware/lib/firmware/amdgpu/aldebaran_mec2.bin
 amdgpu-firmware/lib/firmware/amdgpu/aldebaran_rlc.bin
 amdgpu-firmware/lib/firmware/amdgpu/aldebaran_sdma.bin
 amdgpu-firmware/lib/firmware/amdgpu/aldebaran_smc.bin
 amdgpu-firmware/lib/firmware/amdgpu/aldebaran_sos.bin
 amdgpu-firmware/lib/firmware/amdgpu/aldebaran_ta.bin
 amdgpu-firmware/lib/firmware/amdgpu/aldebaran_vcn.bin
 amdgpu-firmware/lib/firmware/amdgpu/arcturus_sdma.bin
 amdgpu-firmware/lib/firmware/amdgpu/beige_goby_ce.bin
 amdgpu-firmware/lib/firmware/amdgpu/beige_goby_dmcub.bin
 amdgpu-firmware/lib/firmware/amdgpu/beige_goby_me.bin
 amdgpu-firmware/lib/firmware/amdgpu/beige_goby_mec.bin
 amdgpu-firmware/lib/firmware/amdgpu/beige_goby_mec2.bin
 amdgpu-firmware/lib/firmware/amdgpu/beige_goby_pfp.bin
 amdgpu-firmware/lib/firmware/amdgpu/beige_goby_rlc.bin
 amdgpu-firmware/lib/firmware/amdgpu/beige_goby_sdma.bin
 amdgpu-firmware/lib/firmware/amdgpu/beige_goby_smc.bin
 amdgpu-firmware/lib/firmware/amdgpu/beige_goby_sos.bin
 amdgpu-firmware/lib/firmware/amdgpu/beige_goby_ta.bin
 amdgpu-firmware/lib/firmware/amdgpu/beige_goby_vcn.bin
 amdgpu-firmware/lib/firmware/amdgpu/cyan_skillfish2_ce.bin
 amdgpu-firmware/lib/firmware/amdgpu/cyan_skillfish2_me.bin
 amdgpu-firmware/lib/firmware/amdgpu/cyan_skillfish2_mec.bin
 amdgpu-firmware/lib/firmware/amdgpu/cyan_skillfish2_mec2.bin
 amdgpu-firmware/lib/firmware/amdgpu/cyan_skillfish2_pfp.bin
 amdgpu-firmware/lib/firmware/amdgpu/dcn_3_1_6_dmcub.bin
 amdgpu-firmware/lib/firmware/amdgpu/dimgrey_cavefish_ce.bin
 amdgpu-firmware/lib/firmware/amdgpu/dimgrey_cavefish_dmcub.bin
 amdgpu-firmware/lib/firmware/amdgpu/dimgrey_cavefish_me.bin
 amdgpu-firmware/lib/firmware/amdgpu/dimgrey_cavefish_mec.bin
 amdgpu-firmware/lib/firmware/amdgpu/dimgrey_cavefish_mec2.bin
 amdgpu-firmware/lib/firmware/amdgpu/dimgrey_cavefish_pfp.bin
 amdgpu-firmware/lib/firmware/amdgpu/dimgrey_cavefish_rlc.bin
 amdgpu-firmware/lib/firmware/amdgpu/dimgrey_cavefish_sdma.bin
 amdgpu-firmware/lib/firmware/amdgpu/dimgrey_cavefish_smc.bin
 amdgpu-firmware/lib/firmware/amdgpu/dimgrey_cavefish_sos.bin
 amdgpu-firmware/lib/firmware/amdgpu/dimgrey_cavefish_ta.bin
 amdgpu-firmware/lib/firmware/amdgpu/dimgrey_cavefish_vcn.bin
 amdgpu-firmware/lib/firmware/amdgpu/gc_10_3_7_ce.bin
 amdgpu-firmware/lib/firmware/amdgpu/gc_10_3_7_me.bin
 amdgpu-firmware/lib/firmware/amdgpu/gc_10_3_7_mec.bin
 amdgpu-firmware/lib/firmware/amdgpu/gc_10_3_7_mec2.bin
 amdgpu-firmware/lib/firmware/amdgpu/gc_10_3_7_pfp.bin
 amdgpu-firmware/lib/firmware/amdgpu/gc_10_3_7_rlc.bin
 amdgpu-firmware/lib/firmware/amdgpu/green_sardine_asd.bin
 amdgpu-firmware/lib/firmware/amdgpu/green_sardine_ce.bin
 amdgpu-firmware/lib/firmware/amdgpu/green_sardine_dmcub.bin
 amdgpu-firmware/lib/firmware/amdgpu/green_sardine_me.bin
 amdgpu-firmware/lib/firmware/amdgpu/green_sardine_mec.bin
 amdgpu-firmware/lib/firmware/amdgpu/green_sardine_mec2.bin
 amdgpu-firmware/lib/firmware/amdgpu/green_sardine_pfp.bin
 amdgpu-firmware/lib/firmware/amdgpu/green_sardine_rlc.bin
 amdgpu-firmware/lib/firmware/amdgpu/green_sardine_ta.bin
 amdgpu-firmware/lib/firmware/amdgpu/green_sardine_vcn.bin
 amdgpu-firmware/lib/firmware/amdgpu/navi10_asd.bin
 amdgpu-firmware/lib/firmware/amdgpu/navi10_ce.bin
 amdgpu-firmware/lib/firmware/amdgpu/navi10_me.bin
 amdgpu-firmware/lib/firmware/amdgpu/navi10_mec.bin
 amdgpu-firmware/lib/firmware/amdgpu/navi10_mec2.bin
 amdgpu-firmware/lib/firmware/amdgpu/navi10_pfp.bin
 amdgpu-firmware/lib/firmware/amdgpu/navi10_sos.bin
 amdgpu-firmware/lib/firmware/amdgpu/navi10_ta.bin
 amdgpu-firmware/lib/firmware/amdgpu/navi10_vcn.bin
 amdgpu-firmware/lib/firmware/amdgpu/navi12_asd.bin
 amdgpu-firmware/lib/firmware/amdgpu/navi12_sdma.bin
 amdgpu-firmware/lib/firmware/amdgpu/navi12_sdma1.bin
 amdgpu-firmware/lib/firmware/amdgpu/navi12_sos.bin
 amdgpu-firmware/lib/firmware/amdgpu/navi12_ta.bin
 amdgpu-firmware/lib/firmware/amdgpu/navi12_vcn.bin
 amdgpu-firmware/lib/firmware/amdgpu/navi14_asd.bin
 amdgpu-firmware/lib/firmware/amdgpu/navi14_smc.bin
 amdgpu-firmware/lib/firmware/amdgpu/navi14_sos.bin
 amdgpu-firmware/lib/firmware/amdgpu/navi14_ta.bin
 amdgpu-firmware/lib/firmware/amdgpu/navi14_vcn.bin
 amdgpu-firmware/lib/firmware/amdgpu/navy_flounder_ce.bin
 amdgpu-firmware/lib/firmware/amdgpu/navy_flounder_dmcub.bin
 amdgpu-firmware/lib/firmware/amdgpu/navy_flounder_me.bin
 amdgpu-firmware/lib/firmware/amdgpu/navy_flounder_mec.bin
 amdgpu-firmware/lib/firmware/amdgpu/navy_flounder_mec2.bin
 amdgpu-firmware/lib/firmware/amdgpu/navy_flounder_pfp.bin
 amdgpu-firmware/lib/firmware/amdgpu/navy_flounder_rlc.bin
 amdgpu-firmware/lib/firmware/amdgpu/navy_flounder_sdma.bin
 amdgpu-firmware/lib/firmware/amdgpu/navy_flounder_smc.bin
 amdgpu-firmware/lib/firmware/amdgpu/navy_flounder_sos.bin
 amdgpu-firmware/lib/firmware/amdgpu/navy_flounder_ta.bin
 amdgpu-firmware/lib/firmware/amdgpu/navy_flounder_vcn.bin
 amdgpu-firmware/lib/firmware/amdgpu/picasso_asd.bin
 amdgpu-firmware/lib/firmware/amdgpu/picasso_ce.bin
 amdgpu-firmware/lib/firmware/amdgpu/picasso_me.bin
 amdgpu-firmware/lib/firmware/amdgpu/picasso_mec.bin
 amdgpu-firmware/lib/firmware/amdgpu/picasso_mec2.bin
 amdgpu-firmware/lib/firmware/amdgpu/picasso_pfp.bin
 amdgpu-firmware/lib/firmware/amdgpu/picasso_ta.bin
 amdgpu-firmware/lib/firmware/amdgpu/picasso_vcn.bin
 amdgpu-firmware/lib/firmware/amdgpu/psp_13_0_8_asd.bin
 amdgpu-firmware/lib/firmware/amdgpu/psp_13_0_8_ta.bin
 amdgpu-firmware/lib/firmware/amdgpu/psp_13_0_8_toc.bin
 amdgpu-firmware/lib/firmware/amdgpu/raven2_asd.bin
 amdgpu-firmware/lib/firmware/amdgpu/raven2_ce.bin
 amdgpu-firmware/lib/firmware/amdgpu/raven2_me.bin
 amdgpu-firmware/lib/firmware/amdgpu/raven2_mec.bin
 amdgpu-firmware/lib/firmware/amdgpu/raven2_mec2.bin
 amdgpu-firmware/lib/firmware/amdgpu/raven2_pfp.bin
 amdgpu-firmware/lib/firmware/amdgpu/raven2_ta.bin
 amdgpu-firmware/lib/firmware/amdgpu/raven2_vcn.bin
 amdgpu-firmware/lib/firmware/amdgpu/raven_asd.bin
 amdgpu-firmware/lib/firmware/amdgpu/raven_ce.bin
 amdgpu-firmware/lib/firmware/amdgpu/raven_me.bin
 amdgpu-firmware/lib/firmware/amdgpu/raven_mec.bin
 amdgpu-firmware/lib/firmware/amdgpu/raven_mec2.bin
 amdgpu-firmware/lib/firmware/amdgpu/raven_pfp.bin
 amdgpu-firmware/lib/firmware/amdgpu/raven_ta.bin
 amdgpu-firmware/lib/firmware/amdgpu/raven_vcn.bin
 amdgpu-firmware/lib/firmware/amdgpu/renoir_asd.bin
 amdgpu-firmware/lib/firmware/amdgpu/renoir_ce.bin
 amdgpu-firmware/lib/firmware/amdgpu/renoir_dmcub.bin
 amdgpu-firmware/lib/firmware/amdgpu/renoir_me.bin
 amdgpu-firmware/lib/firmware/amdgpu/renoir_mec.bin
 amdgpu-firmware/lib/firmware/amdgpu/renoir_mec2.bin
 amdgpu-firmware/lib/firmware/amdgpu/renoir_pfp.bin
 amdgpu-firmware/lib/firmware/amdgpu/renoir_rlc.bin
 amdgpu-firmware/lib/firmware/amdgpu/renoir_ta.bin
 amdgpu-firmware/lib/firmware/amdgpu/renoir_vcn.bin
 amdgpu-firmware/lib/firmware/amdgpu/sdma_5_2_7.bin
 amdgpu-firmware/lib/firmware/amdgpu/sienna_cichlid_ce.bin
 amdgpu-firmware/lib/firmware/amdgpu/sienna_cichlid_dmcub.bin
 amdgpu-firmware/lib/firmware/amdgpu/sienna_cichlid_me.bin
 amdgpu-firmware/lib/firmware/amdgpu/sienna_cichlid_mec.bin
 amdgpu-firmware/lib/firmware/amdgpu/sienna_cichlid_mec2.bin
 amdgpu-firmware/lib/firmware/amdgpu/sienna_cichlid_pfp.bin
 amdgpu-firmware/lib/firmware/amdgpu/sienna_cichlid_rlc.bin
 amdgpu-firmware/lib/firmware/amdgpu/sienna_cichlid_sdma.bin
 amdgpu-firmware/lib/firmware/amdgpu/sienna_cichlid_smc.bin
 amdgpu-firmware/lib/firmware/amdgpu/sienna_cichlid_sos.bin
 amdgpu-firmware/lib/firmware/amdgpu/sienna_cichlid_ta.bin
 amdgpu-firmware/lib/firmware/amdgpu/sienna_cichlid_vcn.bin
 amdgpu-firmware/lib/firmware/amdgpu/vangogh_asd.bin
 amdgpu-firmware/lib/firmware/amdgpu/vangogh_ce.bin
 amdgpu-firmware/lib/firmware/amdgpu/vangogh_me.bin
 amdgpu-firmware/lib/firmware/amdgpu/vangogh_mec.bin
 amdgpu-firmware/lib/firmware/amdgpu/vangogh_mec2.bin
 amdgpu-firmware/lib/firmware/amdgpu/vangogh_pfp.bin
 amdgpu-firmware/lib/firmware/amdgpu/vega10_asd.bin
 amdgpu-firmware/lib/firmware/amdgpu/vega10_ce.bin
 amdgpu-firmware/lib/firmware/amdgpu/vega10_me.bin
 amdgpu-firmware/lib/firmware/amdgpu/vega10_mec.bin
 amdgpu-firmware/lib/firmware/amdgpu/vega10_mec2.bin
 amdgpu-firmware/lib/firmware/amdgpu/vega10_pfp.bin
 amdgpu-firmware/lib/firmware/amdgpu/vega12_asd.bin
 amdgpu-firmware/lib/firmware/amdgpu/vega12_ce.bin
 amdgpu-firmware/lib/firmware/amdgpu/vega12_me.bin
 amdgpu-firmware/lib/firmware/amdgpu/vega12_mec.bin
 amdgpu-firmware/lib/firmware/amdgpu/vega12_mec2.bin
 amdgpu-firmware/lib/firmware/amdgpu/vega12_pfp.bin
 amdgpu-firmware/lib/firmware/amdgpu/vega20_asd.bin
 amdgpu-firmware/lib/firmware/amdgpu/vega20_ce.bin
 amdgpu-firmware/lib/firmware/amdgpu/vega20_me.bin
 amdgpu-firmware/lib/firmware/amdgpu/vega20_mec.bin
 amdgpu-firmware/lib/firmware/amdgpu/vega20_mec2.bin
 amdgpu-firmware/lib/firmware/amdgpu/vega20_pfp.bin
 amdgpu-firmware/lib/firmware/amdgpu/yellow_carp_asd.bin
 amdgpu-firmware/lib/firmware/amdgpu/yellow_carp_ce.bin
 amdgpu-firmware/lib/firmware/amdgpu/yellow_carp_me.bin
 amdgpu-firmware/lib/firmware/amdgpu/yellow_carp_mec.bin
 amdgpu-firmware/lib/firmware/amdgpu/yellow_carp_mec2.bin
 amdgpu-firmware/lib/firmware/amdgpu/yellow_carp_pfp.bin
 amdgpu-firmware/lib/firmware/amdgpu/yellow_carp_rlc.bin
 amdgpu-firmware/lib/firmware/amdgpu/yellow_carp_ta.bin
 ibt-firmware/lib/firmware/intel/ibt-hw-37.8.10-fw-22.50.19.14.f.bseq
 iwlwifi-firmware-ax210/lib/firmware/iwlwifi-ty-a0-gf-a0.pnvm
 iwlwifi-firmware-iwl9260/lib/firmware/iwlwifi-9260-th-b0-jf-b0-46.ucode
 iwlwifi-firmware-iwl9000/lib/firmware/iwlwifi-9000-pu-b0-jf-b0-46.ucode

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2022-04-17 16:20:17 +02:00
Petr Štetiar
c0a6fefd9b Revert "mac80211 adjust QCA9561 PA bias"
This reverts commit f9ff282d17 as during
upstream patch review process nbd pointed out, that this patch needs
more work:

 "The patch looks wrong to me. I'm pretty sure that AR_CH0_TOP2 is the
  correct register, the definition has an explicit check for 9561 as well.
  I believe this patch works by accident because it avoids writing a wrong
  value to that register."

1. https://lore.kernel.org/all/91c58969-c60e-2f41-00ac-737786d435ae@nbd.name

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2022-04-17 09:20:26 +02:00
Martin Kennedy
a5ac8ad0ba realtek: add ZyXEL GS1900-24HP v1 support
The ZyXEL GS1900-24HP v1 is a 24 port PoE switch with two SFP ports,
similar to the other GS1900 switches.

Specifications
--------------
* Device:    ZyXEL GS1900-24HP v1
* SoC:       Realtek RTL8382M 500 MHz MIPS 4KEc
* Flash:     16 MiB
* RAM:       Winbond W9751G8KB-25 64 MiB DDR2 SDRAM
* Ethernet:  24x 10/100/1000 Mbps, 2x SFP 100/1000 Mbps
* LEDs:
  * 1 PWR LED (green, not configurable)
  * 1 SYS LED (green, configurable)
  * 24 ethernet port link/activity LEDs (green, SoC controlled)
  * 24 ethernet port PoE status LEDs
  * 2 SFP status/activity LEDs (green, SoC controlled)
* Buttons:
  * 1 "RESET" button on front panel (soft reset)
  * 1 button ('SW1') behind right hex grate (hardwired power-off)
* PoE:
  * Management MCU: ST Micro ST32F100 Microcontroller
  * 6 BCM59111 PSE chips
  * 170W power budget
* Power:     120-240V AC C13
* UART:      Internal populated 10-pin header ('J5') providing RS232;
             connected to SoC UART through a TI or SIPEX 3232C for voltage
             level shifting.

* 'J5' RS232 Pinout (dot as pin 1):
  2) SoC RXD
  3) GND
  10) SoC TXD

Serial connection parameters: 115200 8N1.

Installation
------------

OEM upgrade method:

* Log in to OEM management web interface

* Navigate to Maintenance > Firmware > Management

* If "Active Image" has the first option selected, OpenWrt will need to be
  flashed to the "Active" partition. If the second option is selected,
  OpenWrt will need to be flashed to the "Backup" partition.

* Navigate to Maintenance > Firmware > Upload

* Upload the openwrt-realtek-rtl838x-zyxel_gs1900-24hp-v1-initramfs-kernel.bin
  file by your preferred method to the previously determined partition.
  When prompted, select to boot from the newly flashed image, and reboot
  the switch.

* Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it:

  > sysupgrade /tmp/openwrt-realtek-rtl838x-zyxel_gs1900-24hp-v1-squashfs-sysupgrade.bin

U-Boot TFTP method:

* Configure your client with a static 192.168.1.x IP (e.g. 192.168.1.10).

* Set up a TFTP server on your client and make it serve the initramfs
  image.

* Connect serial, power up the switch, interrupt U-boot by hitting the
  space bar, and enable the network:

  > rtk network on

* Since the GS1900-24HP v1 is a dual-partition device, you want to keep the
  OEM firmware on the backup partition for the time being. OpenWrt can
  only be installed in the first partition anyway (hardcoded in the
  DTS). To ensure we are set to boot from the first partition, issue the
  following commands:

  > setsys bootpartition 0
  > savesys

* Download the image onto the device and boot from it:

  > tftpboot 0x81f00000 192.168.1.10:openwrt-realtek-rtl838x-zyxel_gs1900-24hp-v1-initramfs-kernel.bin
  > bootm

* Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it:

  > sysupgrade /tmp/openwrt-realtek-rtl838x-zyxel_gs1900-24hp-v1-squashfs-sysupgrade.bin

Signed-off-by: Martin Kennedy <hurricos@gmail.com>
[Add info on PoE hardware to commit message]
Signed-off-by: Sander Vanheule <sander@svanheule.net>
2022-04-16 17:26:56 +02:00
Andrew Powers-Holmes
6f1efb2898 ath79: add support for Sophos AP100/AP55 family
The Sophos AP100, AP100C, AP55, and AP55C are dual-band 802.11ac access
points based on the Qualcomm QCA9558 SoC. They share PCB designs with
several devices that already have partial or full support, most notably the
Devolo DVL1750i/e.

The AP100 and AP100C are hardware-identical to the AP55 and AP55C, however
the 55 models' ART does not contain calibration data for their third chain
despite it being present on the PCB.

Specifications common to all models:
 - Qualcomm QCA9558 SoC @ 720 MHz (MIPS 74Kc Big-endian processor)
 - 128 MB RAM
 - 16 MB SPI flash
 - 1x 10/100/1000 Mbps Ethernet port, 802.3af PoE-in
 - Green and Red status LEDs sharing a single external light-pipe
 - Reset button on PCB[1]
 - Piezo beeper on PCB[2]
 - Serial UART header on PCB
 - Alternate power supply via 5.5x2.1mm DC jack @ 12 VDC

Unique to AP100 and AP100C:
 - 3T3R 2.4GHz 802.11b/g/n via SoC WMAC
 - 3T3R 5.8GHz 802.11a/n/ac via QCA9880 (PCI Express)

AP55 and AP55C:
 - 2T2R 2.4GHz 802.11b/g/n via SoC WMAC
 - 2T2R 5.8GHz 802.11a/n/ac via QCA9880 (PCI Express)

AP100 and AP55:
 - External RJ45 serial console port[3]
 - USB 2.0 Type A port, power controlled via GPIO 11

Flashing instructions:

This firmware can be flashed either via a compatible Sophos SG or XG
firewall appliance, which does not require disassembling the device, or via
the U-Boot console available on the internal UART header.

To flash via XG appliance:
 - Register on Sophos' website for a no-cost Home Use XG firewall license
 - Download and install the XG software on a compatible PC or virtual
   machine, complete initial appliance setup, and enable SSH console access
 - Connect the target AP device to the XG appliance's LAN interface
 - Approve the AP from the XG Web UI and wait until it shows as Active
   (this can take 3-5 minutes)
 - Connect to the XG appliance over SSH and access the Advanced Console
   (Menu option 5, then menu option 3)
 - Run `sudo awetool` and select the menu option to connect to an AP via
   SSH. When prompted to enable SSH on the target AP, select Yes.
 - Wait 2-3 minutes, then select the AP from the awetool menu again. This
   will connect you to a root shell on the target AP.
 - Copy the firmware to /tmp/openwrt.bin on the target AP via SCP/TFTP/etc
 - Run `mtd -r write /tmp/openwrt.bin astaro_image`
 - When complete, the access point will reboot to OpenWRT.

To flash via U-Boot serial console:
 - Configure a TFTP server on your PC, and set IP address 192.168.99.8 with
   netmask 255.255.255.0
 - Copy the firmware .bin to the TFTP server and rename to 'uImage_AP100C'
 - Open the target AP's enclosure and locate the 4-pin 3.3V UART header [4]
 - Connect the AP ethernet to your PC's ethernet port
 - Connect a terminal to the UART at 115200 8/N/1 as usual
 - Power on the AP and press a key to cancel autoboot when prompted
 - Run the following commands at the U-Boot console:
    - `tftpboot`
    - `cp.b $fileaddr 0x9f070000 $filesize`
    - `boot`
 - The access point will boot to OpenWRT.

MAC addresses as verified by OEM firmware:

use   address     source
LAN   label       config 0x201a (label)
2g    label + 1   art 0x1002    (also found at config 0x2004)
5g    label + 9   art 0x5006

Increments confirmed across three AP55C, two AP55, and one AP100C.

These changes have been tested to function on both current master and
21.02.0 without any obvious issues.

[1] Button is present but does not alter state of any GPIO on SoC
[2] Buzzer and driver circuitry is present on PCB but is not connected to
    any GPIO. Shorting an unpopulated resistor next to the driver circuitry
    should connect the buzzer to GPIO 4, but this is unconfirmed.
[3] This external RJ45 serial port is disabled in the OEM firmware, but
    works in OpenWRT without additional configuration, at least on my
    three test units.
[4] On AP100/AP55 models the UART header is accessible after removing
    the device's top cover. On AP100C/AP55C models, the PCB must be removed
    for access; three screws secure it to the case.
    Pin 1 is marked on the silkscreen. Pins from 1-4 are 3.3V, GND, TX, RX

Signed-off-by: Andrew Powers-Holmes <andrew@omnom.net>
2022-04-16 16:59:29 +02:00
Abdul Aziz Amar
78c3534645 ramips: add support for BOLT! Arion
This device is from now-defunct BOLT! ISP in Indonesia.
The original firmware is based on mediatek SDK running linux 2.6 or 3.x in later revision.

Specifications:

- SoC:      MediaTek MT7621
- Flash:    32 MiB NOR SPI
- RAM:      128 MiB DDR3
- Ethernet: 2x 10/100/1000 Mbps (switched, LAN + WAN)
- WIFI0:    MT7603E 2.4GHz 802.11b/g/n
- WIFI1:    MT7612E 5GHz 802.11ac
- Antennas: 2x internal, non-detachable
- LEDs:     Programmable LEDs: 5 blue LEDs (wlan, tel, sig1-3) and 2 red LEDs (wlan and sig1)
            Non-programmable "Power"  LED
- Buttons:  Reset and WPS

Instalation:
Install from TFTP

Set your PC IP to 10.10.10.3 and gateway to 10.10.10.123
Press "1" when turning on the router, and type the initramfs file name

You also need to solder pin header or cable to J4 or neighboring test points (T19-T21)
Pinouts from top to bottom: GND, TX, RX, VCC (3.3v)
Baudrate: 57600n8

There's also an additional gigabit transformer and RTL8211FD managed by the LTE module on the backside of the PCB.

Signed-off-by: Abdul Aziz Amar <abdulaziz.amar@gmail.com>
2022-04-16 14:02:11 +02:00
Rosen Penev
b363f74886 readline: add host PIC
Python seems to fail to link to libreadline properly because of this.
Not a fatal error but an error nontheless.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2022-04-16 14:02:11 +02:00
Rosen Penev
fc60b97a77 pcre: pass -fPIC under host as well
static libraries need them as they are not PIC by default.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2022-04-16 14:02:11 +02:00
Cezary Jackiewicz
e02fb42c53 comgt: support ZTE MF286R modem
The modem is based on Marvell PXA1826 and uses ACM+RNDIS interface to
establish connection with custom commands specific to ZTE modems.
Two variants of modems were discovered, some identifying themselves
as "ZTE", and others as plain "Marvell", the chipset manufacturer.
The modem itself runs a fork of OpenWrt inside, which root shell can be
accessed via ADB interface.

Signed-off-by: Cezary Jackiewicz <cezary@eko.one.pl>
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
2022-04-16 14:02:11 +02:00
Lech Perczak
ed7957810c comgt: ncm: try to detect interface for ttyACM ports
Some modems expose ttyACM as their control ports, which have the
"device" symlink pointing one level down in sysfs tree. Try to find
network interfaces for them as well, this is commonly used for modems
exposing ACM + RNDIS or ACM + ECM interface combinations.

Co-developed-by: Cezary Jackiewicz <cezary@eko.one.pl>
Signed-off-by: Cezary Jackiewicz <cezary@eko.one.pl>
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
2022-04-16 14:02:11 +02:00
Lech Perczak
b2940bb8b2 comgt: ncm: select first available network interface for device
Some modems expose multiple network interfaces on the same USB device,
causing the connection setup script to fail, because glob matching in
the detection phase causes 'ls' to output more than one interface name
plus their base directories in sysfs. Avoid that by listing the
directories explicitly and then selecting first available interface.
This is the case for some variants of ZTE MF286R built-in modem, which
exposes both RNDIS and CDC-ECM network interfaces, causing the
connection setup to fail.

Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
2022-04-16 14:02:11 +02:00
Lech Perczak
a67629bbe2 comgt: ncm: allow specification of interface name
Add ifname property to UCI, which can be used to override the
autodetected interface name in case the detection fails due to having
none or more than one interface exposed by the modem, which is not
explicitly linked to TTY port. This is needed on certain variants of ZTE
MF286R built-in modem, which exposes both RNDIS and CDC-ECM interfaces
on the modem, on which the automatic detection may select the wrong
network interface.

Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
2022-04-16 14:02:11 +02:00
Thibaut VARÈNE
a05dcb0724 ath79: add support for Yuncore A930
Specification:

- QCA9533 (650 MHz), 64 or 128MB RAM, 16MB SPI NOR
- 2x 10/100 Mbps Ethernet, with 802.3at PoE support (WAN)
- 2T2R 802.11b/g/n 2.4GHz

Flash instructions:

If your device comes with generic QSDK based firmware, you can login
over telnet (login: root, empty password, default IP: 192.168.188.253),
issue first (important!) 'fw_setenv' command and then perform regular
upgrade, using 'sysupgrade -n -F ...' (you can use 'wget' to download
image to the device, SSH server is not available):

  fw_setenv bootcmd "bootm 0x9f050000 || bootm 0x9fe80000"
  sysupgrade -n -F openwrt-...-yuncore_...-squashfs-sysupgrade.bin

In case your device runs firmware with YunCore custom GUI, you can use
U-Boot recovery mode:

1. Set a static IP 192.168.0.141/24 on PC and start TFTP server with
   'tftp' image renamed to 'upgrade.bin'
2. Power the device with reset button pressed and release it after 5-7
   seconds, recovery mode should start downloading image from server
   (unfortunately, there is no visible indication that recovery got
   enabled - in case of problems check TFTP server logs)

Signed-off-by: Clemens Hopfer <openwrt@wireloss.net>
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
2022-04-15 07:11:18 +02:00
Thibaut VARÈNE
f9ff282d17 mac80211 adjust QCA9561 PA bias
ath9k is setting the TX PA DC bias level different on QCA9561 and QCA9565
although they have the same radio IP-core, which results in a very low
output power and very low throughput as devices are further away from
the AP (compared to other 2.4GHz APs.)

In real life testing, without this patch the 2.4GHz throughput on Yuncore
XD3200 is around 10Mbps sitting close to the AP, and close to theoretical
maximum with the patch applied.

Signed-off-by: Clemens Hopfer <openwrt@wireloss.net>
[edit commit message]
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
2022-04-15 07:11:18 +02:00
Thibaut VARÈNE
c91df224f5 ath79: add support for Yuncore XD3200
Specification:

- QCA9563 (775MHz), 128MB RAM, 16MB SPI NOR
- 2T2R 802.11b/g/n 2.4GHz
- 2T2R 802.11n/ac 5GHz
- 2x 10/100/1000 Mbps Ethernet, with 802.3at PoE support (WAN port)

LED for 5 GHz WLAN is currently not supported as it is connected directly
to the QCA9882 radio chip.

Flash instructions:

If your device comes with generic QSDK based firmware, you can login
over telnet (login: root, empty password, default IP: 192.168.188.253),
issue first (important!) 'fw_setenv' command and then perform regular
upgrade, using 'sysupgrade -n -F ...' (you can use 'wget' to download
image to the device, SSH server is not available):

  fw_setenv bootcmd "bootm 0x9f050000 || bootm 0x9fe80000"
  sysupgrade -n -F openwrt-...-yuncore_...-squashfs-sysupgrade.bin

In case your device runs firmware with YunCore custom GUI, you can use
U-Boot recovery mode:

1. Set a static IP 192.168.0.141/24 on PC and start TFTP server with
   'tftp' image renamed to 'upgrade.bin'
2. Power the device with reset button pressed and release it after 5-7
   seconds, recovery mode should start downloading image from server
   (unfortunately, there is no visible indication that recovery got
   enabled - in case of problems check TFTP server logs)

Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
2022-04-15 07:11:18 +02:00
Petr Štetiar
afb0e9336e kernel: usb-net-asix: fix 5.15 dependency
Upstream in commit 34a1dee6bc44 ("net: usb: asix: ax88772: add generic
selftest support") in version 5.14 added dependency on generic selftest
functionality and armvirt/64 when compiled with ALL_KMODS=y reports following:

 Package kmod-usb-net-asix is missing dependencies for the following libraries:
 mdio_devres.ko
 selftests.ko

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2022-04-15 07:11:18 +02:00
Petr Štetiar
8361946e1b kernel: netdevices: add generic selftests module
Upstream in commit 3e1e58d64c3d ("net: add generic selftest support") in
version 5.13 added generic selftests module and usb-net-asix already
depends on it, in version 5.18 via commit 1710b52d7c13 ("net: usb:
smsc95xx: add generic selftest support") it will be used by
usb-net-smsc95xx as well.

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2022-04-15 07:11:18 +02:00
Petr Štetiar
0225469dcd kernel: usb-net-smsc95xx: fix 5.15 dependency
armvirt/64 when compiled with ALL_KMODS=y reports following:

 Package kmod-usb-net-smsc95xx is missing dependencies for the following libraries:
 libphy.ko

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2022-04-15 07:11:18 +02:00
Petr Štetiar
0fa0a19a60 kernel: mdio-devres: fix of-mdio dependency
armvirt/64 when compiled with ALL_KMODS=y reports following:

 Package kmod-mdio-devres is missing dependencies for the following libraries:
 of_mdio.ko

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2022-04-15 07:11:18 +02:00
Petr Štetiar
c707731310 kernel: of-mdio: fix 5.15 fwnode_mdio dependency
Upstream in commit bc1bee3b87ee ("net: mdiobus: Introduce
fwnode_mdiobus_register_phy()") in version 5.14 introduced new
dependency:

 Package kmod-of-mdio is missing dependencies for the following libraries:

  fwnode_mdio.ko

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2022-04-15 07:11:18 +02:00
Jason A. Donenfeld
a001630a1a urandom-seed: go back to seeding with shell script temporarily
This reverts commit 2edc017a6e.

We shouldn't be using a shell script here, but the SeedRNG integration
into OpenWRT requires a bit more thought. Etienne raised some important
points immediately after this was merged and planned to send some follow
up commits, but became busy with other things. The points he raised are
important enough that we should actually back this out until it's ready
to go, and then merge it as a cohesive unit. So let's revert this for
now, and come back to it later on.

Cc: Etienne Champetier <champetier.etienne@gmail.com>
Cc: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
2022-04-14 10:12:34 +02:00
Daniel Golle
c5f113c43f
netifd: relax check in dhcp proto handler
Checking whether /sbin/udhcpc is a symbolic link breaks using the
DHCP proto handler inside procd-ujail where bind-mounts are used for
the resolved link. Check whether /sbin/udhcpc is executable instead
to allow using the proto handler for DHCP-provisioned containers.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-04-13 19:51:00 +01:00
Daniel Golle
2c8873033e
procd: update to git HEAD
6343c3a procd: completely remove tmp-on-zram support
 5c5e63f uxc: fix potential NULL-pointer dereference
 eb03f03 jail: include necessary files for per-netns netifd instance

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-04-13 19:50:55 +01:00
Daniel Golle
0dbca1b2ba
base-files: more robust sysupgrade on NAND
Make sure sysupgrade on NAND also works in case of UBI volumes having
index >9. While at it, also make sure UBI device is detected and abort
in case it isn't. Use Shell built-in shorthand ':' instead of 'true'.

Fixes #9708
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-04-13 19:50:45 +01:00
Rui Salvaterra
435d7a052b firewall3: bump to latest git HEAD
4cd7d4f Revert "firewall3: support table load on access on Linux 5.15+"
50979cc firewall3: remove unnecessary fw3_has_table

Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
2022-04-13 17:08:17 +01:00
Jo-Philipp Wich
bea01fa57f netfilter: move nf-log modules into separate packages
Both legacy iptables and nftables require nf-log modules for rule logging,
so move them into a separate package both firewall implementations can
depend on.

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2022-04-12 14:02:16 +02:00
Felix Fietkau
5d5afd5177 mac80211: backport minstrel_ht fix for legacy rates
Fixes OFDM rates on 5 GHz

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-04-12 09:33:22 +02:00
Eneas U de Queiroz
1135b75d1f nftables: add CONFLICT between versions
Have nftables-json conflict with nftables-nojson.

Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
2022-04-11 21:41:03 +02:00
Eneas U de Queiroz
e89f3e85eb wolfssl: bump to 5.2.0
Fixes two high-severity vulnerabilities:

- CVE-2022-25640: A TLS v1.3 server who requires mutual authentication
  can be bypassed.  If a malicious client does not send the
  certificate_verify message a client can connect without presenting a
  certificate even if the server requires one.

- CVE-2022-25638: A TLS v1.3 client attempting to authenticate a TLS
  v1.3 server can have its certificate heck bypassed. If the sig_algo in
  the certificate_verify message is different than the certificate
  message checking may be bypassed.

Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
2022-04-11 21:41:03 +02:00
Hauke Mehrtens
3aa96efa24 mac80211: Update to version 5.15.33-1
This updates mac80211 to version 5.15.33-1 which is based on kernel
5.15.33.
The removed patches were applied upstream.

This new release contains many fixes which were merged into the upstream
Linux kernel.
This also contains the following new drivers which are needed for ath11k:
* net/qrtr/
* drivers/bus/mhi/

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2022-04-10 23:12:36 +02:00
Daniel Golle
dffad93d3e
arm-trusted-firmware-mediatek: remove no longer needed Configure step
As anyway only the default is called now we can as well also just remove
the override for Build/Configure.

Fixes: e2cffbb805 ("arm-trusted-firmware-mediatek: update to 2021-03-10")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-04-09 22:24:42 +01:00
Robert Marko
6461384c1e mwlwifi: fix 5.15 kernel support
Fix compilation and usage under kernel 5.15 for the mwlwifi driver.

For detailed description of changes, check individual patches.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
2022-04-09 19:31:46 +02:00
Konstantin Demin
65256aee23 dropbear: bump to 2022.82
- update dropbear to latest stable 2022.82;
  for the changes see https://matt.ucc.asn.au/dropbear/CHANGES
- use $(AUTORELEASE) in PKG_RELEASE
- use https for all uris
- refresh all patches
- rewrite patches:
  - 100-pubkey_path.patch
  - 130-ssh_ignore_x_args.patch

binary/pkg size changes:
- ath79/generic, mips:
  - binary: 215112 -> 219228 (+4116)
  - pkg: 111914 -> 113404 (+1490)
- ath79/tiny, mips:
  - binary: 172501 -> 172485 (-16)
  - pkg: 89871 -> 90904 (+1033)

Tested-by: Stijn Segers <foss@volatilesystems.org>
Signed-off-by: Konstantin Demin <rockdrilla@gmail.com>
2022-04-09 19:31:31 +02:00
Nick Hainke
c3b7389339 libmnl: update to 1.0.5
Changes:

Duncan Roe (5):
      nlmsg: Fix a missing doxygen section trailer
      build: doc: "make" builds & installs a full set of man pages
      build: doc: get rid of the need for manual updating of Makefile
      build: If doxygen is not available, be sure to report "doxygen: no" to ./configure
      src: doc: Fix messed-up Netlink message batch diagram

Fernando Fernandez Mancera (1):
      src: fix doxygen function documentation

Florian Westphal (1):
      libmnl: zero attribute padding

Guillaume Nault (1):
      callback: mark cb_ctl_array 'const' in mnl_cb_run2()

Kylie McClain (1):
      examples: nfct-daemon: Fix test building on musl libc

Laura Garcia Liebana (4):
      examples: add arp cache dump example
      examples: fix neigh max attributes
      examples: fix print line format
      examples: reduce LOCs during neigh attributes validation

Pablo Neira Ayuso (3):
      doxygen: remove EXPORT_SYMBOL from the output
      include: add MNL_SOCKET_DUMP_SIZE definition
      build: libmnl 1.0.5 release

Petr Vorel (1):
      examples: Add rtnl-addr-add.c

Stephen Hemminger (1):
      examples: rtnl-addr-dump: fix typo

igo95862 (1):
      doxygen: Fixed link to the git source tree on the website.

Signed-off-by: Nick Hainke <vincent@systemli.org>
2022-04-09 18:34:04 +02:00
Nick Hainke
aecf088b37 libnfnetlink: update to 1.0.2
Changes:

c63f193 bump version to 1.0.2
3cffa84 libnfnetlink: Check getsockname() return code
90ba679 include: Silence gcc warning in linux_list.h
bb4f6c8 Make it clear that this library is deprecated
e46569c Minimally resurrect doxygen documentation
5087de4 libnfnetlink: hide private symbols
62ca426 autogen: don't convert __u16 to u_int16_t
efa1d8e src: Use stdint types everywhere
7a1a07c include: Sync with kernel headers
7633f0c libnfnetlink: initialize attribute padding to resolve valgrind warnings
94b68f3 configure: uclinux is also linux
617fe82 src: get source code license header in sync with current licensing terms
97a3960 build: resolve automake-1.12 warnings

Removed the patch 100-missing_include.patch, libnfnetlink compiles fine
with musl without this patch.

Signed-off-by: Nick Hainke <vincent@systemli.org>
2022-04-09 18:33:24 +02:00
Andrey Erokhin
1e991e09b7 gpio-button-hotplug: fix data race
bh_event_add_var can be called by multiple threads concurrently,
so it shall not use a static char buffer

Signed-off-by: Andrey Erokhin <a.erokhin@inango-systems.com>
2022-04-09 15:56:04 +02:00
Felix Fietkau
0392644083 qosify: update to the latest version
92f5e18675bf interface: fix ifname present check in interface status
ef82defaae26 ubus: add active devices to bridger blacklist

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-04-08 13:07:47 +02:00
Jo-Philipp Wich
1a35ac9990 firewall4: update to latest Git HEAD
a378883 fw4: fix emitting family specific redirect rules without any addrs
11feddf fw4: bracketize IPv6 addresses in dnat addr:port notation
9972f7d fw4: ensure to capitalize weekday names
fde8070 treewide: forward compatibility changes

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2022-04-08 10:45:46 +02:00
Jo-Philipp Wich
cef3e6a69c ucode: update to latest Git HEAD
33f1e0b treewide: move json-c compat shims into internal header file
e0e9431 vm: move unhandled exception reporting out of `uc_vm_execute_chunk()`
2b59140 vm: fix callframe double free on unhanded exceptions
7d7e950 main: abort when failing to load a preload library
1032a67 lib: let `json()` accept input objects implementing `read()` method
5ee68d5 fs: implement `fs.readfile()` and `fs.writefile()`
df6b861 ci: debian: change path before attempting to invoke Git operations
dfaf05a ci: debian: automatically update changelog from Git tag
34f3c45 ci: fix YAML syntax of Debian workflow
e956bcf fs: fix off-by-one in fs.dirname() function
6fc4b6c .gitignore: fix overmatching patterns, blacklist cram .venv
7c2e082 build: remove legacy json-c check
77942af build: add polyfills for older libjson-c versions
0b4aaa3 CI: build Debian package
f404285 debian: Add package definition
a37f654 types: fix escape sequence encoding of high byte values in JSON strings
aae5312 Update README.md
8134e25 build: fix symlink install target
87c7296 treewide: replace some leftover "utpl" occurrences, update .gitignore
7d27ad5 build: only stage ucc symlink if compile support is enabled
171402f lib: add date and time related functions
8b5dc60 lib: provide API function to obtain stdlib function implementations
eb0d2f1 main: turn ucode into multicall executable
28ee7e1 uloop: add support for tasks
753dea9 CI: build on macOS
668c5c0 lib: add argument position support (`%m$`) to `sprintf()` and `printf()`
ab46fdf treewide: remove legacy json-c include directives
b8f49b1 tests: 21_regex_literals: generalize syntax error test case
fd2e5e7 tests: 16_sort: fix logic flaw exposed on OS X
2c71bf2 tests: run_tests.sh: pass dummy value to `-T` flag
55c4a90 lib: disallow zero padding for %s formats
0d05cb5 tests: run_tests.sh: use greadlink if available
271e520 resolv: make OS X compatible
d13c320 fs: avoid Linux specific sys/sysmacros.h include on OS X
33397a3 uloop: use execvp() on OS X
bafdc8f lib: add naive sigtimedwait() stub for OS X
ada1585 build: consolidate CMakeLists.txt and cover OS X deviations
befbb69 include: add OS X compatible endian.h header
49838a8 include: rename include guards to avoid clashes with system headers
91f65de nl80211: add missing attributes and correct some attribute flags
b4a1fd5 lib: adjust require(), render() and include() raw mode semantics
4618807 main: rework CLI frontend
73dcd78 lib: fix potential integer underflow on empty render output
c402551 vm: fix crash on object literals with non-string computed properties
efe8a02 syntax: support add new operators
078d686 ubus: add event support
6c66c83 ubus: refactor error and argument handling
1cb04f9 ubus: add object publishing, notify and subscribe support
0e85974 uloop: clear errno before integer conversion attempts
05bd7ed types: treat resource type prototypes as GC roots
a2a26ca lib: introduce uloop binding
6b6d01f vm: release this context on exception in managed method call
1af23a9 tests: fix proto() testcase
4ce69a8 fs: implement access(), mkstemp(), file.flush() and proc.flush()

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2022-04-08 10:45:46 +02:00
David Bauer
f6445cfa1a hostapd: add ubus link-measurements notifications
Notify external ubus subscribers of received link-measurement reports.

Signed-off-by: David Bauer <mail@david-bauer.net>
2022-04-08 01:19:29 +02:00
David Bauer
965aa33a18 hostapd: add ubus method for requesting link measurements
Add a ubus method to request link-measurements from connected STAs.

In addition to the STAs address, the used and maximum transmit power can
be provided by the external process for the link-measurement. If they
are not provided, 0 is used as the default value.

Signed-off-by: David Bauer <mail@david-bauer.net>
2022-04-08 01:19:18 +02:00
David Bauer
2ca5c3da04 hostapd: add support for enabling link measurements
Allow external processes to enable advertisement of link-measurement RRM
capability.

Signed-off-by: David Bauer <mail@david-bauer.net>
2022-04-08 01:19:10 +02:00
Felix Fietkau
fd354ffac9 mt76: update to the latest version
5beb87716e70 mt76: dma: add wrapper macro for accessing queue registers
e0bc736d5617 mt76: add support for overriding the device used for DMA mapping
b8c842daa081 mt76: make number of tokens configurable dynamically
87a962e0608f mt76: mt7915: add Wireless Ethernet Dispatch support
2accb74e6be3 mt76: mt7915: fix using null pointer when wfsys on
e5227f2f3120 mt76: mt7921: Fix the error handling path of mt7921_pci_probe()
ec0e9f4da32f mt76: mt7915: fix possible uninitialized pointer dereference in mt7986_wmac_gpio_setup
5a87be892ba7 mt76: mt7915: fix possible NULL pointer dereference in mt7915_mac_fill_rx_vector
fe441e5d3dcf mt76: mt7915: do not pass data pointer to mt7915_mcu_muru_debug_set
f3ddfe886283 mt76: mt7915: report rx mode value in mt7915_mac_fill_rx_rate
2a0d370cb5fe mt76: mt7915: use 0xff to initialize bitrate_mask in mt7915_init_bitrate_mask
506bb0605e3e mt76: mt7921: Add AP mode support

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-04-07 12:24:59 +02:00
Felix Fietkau
4ec10da2fe ubox: add example /etc/modules.conf + conffiles entry
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-04-07 12:01:56 +02:00
Piotr Dymacz
0892fd9920 uboot-imx: build 'u-boot-dtb.img' for SolidRun CuBox-i
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2022-04-07 09:58:44 +02:00
Piotr Dymacz
e213375894 uboot-imx: bump to 2022.01 release
Two patches were removed because of the changes introduced in upstream:

1. 110-mx6cuboxi-mmc-fallback.patch
Looks like similar changes were introduced in 6c3fbf3e456c ("mx6cuboxi:
customize board_boot_order to access eMMC").

2. 111-mx6cuboxi_defconfig-force-mmc-boot.patch
The 'CONFIG_SPL_FORCE_MMC_BOOT' was removed in 15aec318ef03 ("Revert
"imx: Introduce CONFIG_SPL_FORCE_MMC_BOOT to force MMC boot on falcon
mode").

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2022-04-07 09:58:44 +02:00
Daniel Golle
0d3850dc5a
libselinux: add missing host-build dependency on libsepol/host
The host-build of libselinux requires libsepol/host.
Add the libsepol/host to HOST_BUILD_DEPENDS to allow build on hosts
which don't have libsepol installed.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-04-06 21:54:50 +01:00
Valentyn Datsko
76f55e3c3f
dnsmasq: add procd interface index tracking
Problem exist when dnsmasq is exclusively bind to particular interface.
After reconfiguring or restarting this interface, its index changes, but
dnsmasq uses the old one. When this problem occurs, dnsmasq does not
listen on the correct interface so DHCP does not work, and clients do not
get an IP address. Procd netdev param can be added to restart dnsmasq when
the interface index is changed.

Signed-off-by: Valentyn Datsko <valikk.d@gmail.com>
[combined into a single &&-connected statement]
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-04-06 17:32:42 +01:00
Felix Fietkau
64f629e207 bridger: add bridge forwarding accelerator
This package uses BPF to create a fast path which improves bridging performance
by bypassing the bridge layer. It also supports creating tc offload rules for
hardware that supports it.
Hardware offload support can be used with MT7622 + MT7915 once it is merged

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-04-06 14:13:26 +02:00
Felix Fietkau
c38b2c5f16 qosify: update to the latest version
Replace the tc-full dependency with tc + libnl-tiny

1cd5e12eecdc loader/interface: attach bpf program directly using netlink

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-04-05 21:28:32 +02:00
Felix Fietkau
0b98a55ad6 ubox: update to the latest version
b87a4fdca634 kmodloader: support loading module options and blacklist from /etc/modules.conf

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-04-05 21:28:32 +02:00
Koen Vandeputte
6af46796fa kernel: package mhi mbim driver
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2022-04-05 17:31:04 +02:00
Koen Vandeputte
2519190fec kernel: package mhi wwan ctrl driver
MHI WWAN CTRL allows QCOM-based PCIe modems to expose different modem
control protocols/ports to userspace, including AT, MBIM, QMI, DIAG
and FIREHOSE. These protocols can be accessed directly from userspace
(e.g. AT commands) or via libraries/tools (e.g. libmbim, libqmi, libqcdm)

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2022-04-05 17:31:04 +02:00
Koen Vandeputte
de840a5e01 kernel: package mhi network driver
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2022-04-05 17:31:04 +02:00
Koen Vandeputte
8da3de825a kernel: package mhi pci driver
This driver provides MHI PCI controller driver for devices
such as Qualcomm SDX55 based PCIe modems

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2022-04-05 17:31:04 +02:00
Koen Vandeputte
120e2d91dc kernel: package mhi bus driver
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2022-04-05 17:31:04 +02:00
Felix Fietkau
39ec9edacb bpf-headers: update to linux 5.15
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-04-04 21:08:38 +02:00
Paul Spooren
839b1ff1fc grub2: add missing license
The PKG_LICENSE field was missing.
While at it, normalize the Makefile a bit.

Signed-off-by: Paul Spooren <mail@aparcar.org>
2022-04-04 18:15:02 +02:00
Daniel Golle
82f9ad6ab2
kernel: load device-mapper early on boot
Previously commit openwrt/packages@3abb7cb ("lvm2: Added script and updated Makefile[...]")
couldn't actually work and allow rootfs_data to be stored on a LVM2 as
the necessary kernel modules had not been loaded at this point.
Fix this by loading device-mapper modules early at boot.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-04-03 16:25:05 +01:00
Felix Fietkau
72b93b77a5 bpf-headers: support CONFIG_HZ=300
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-04-01 15:26:08 +02:00
Piotr Dymacz
173198e35a kernel: modules: drop 'AddDepends/bluetooth' calls
Function 'AddDepends/bluetooth' doesn't exist in our codebase.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2022-04-01 14:32:54 +02:00
Vincent Pelletier
15fbb91666 kernel: scale nf_conntrack_max more reasonably
Use the kernel's built-in formula for computing this value.
The value applied by OpenWRT's sysctl configuration file does not scale
with the available memory, under-using hardware capabilities.
Also, that formula also influences net.netfilter.nf_conntrack_buckets,
which should improve conntrack performance in average (fewer connections
per hashtable bucket).

Backport upstream commit for its effect on the number of connections per
hashtable bucket.

Apply a hack patch to set the RAM size divisor to a more reasonable value (2048,
down from 16384) for our use case, a typical router handling several thousands
of connections.

Signed-off-by: Vincent Pelletier <plr.vincent@gmail.com>
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
2022-04-01 13:23:41 +01:00
Paul Spooren
950bd40a27 toolchain: reproducible libstdcpp
A Python script containing an unreproducible path is copied by default.
Remove it before generating the package.

Signed-off-by: Paul Spooren <mail@aparcar.org>
2022-04-01 12:54:58 +01:00
Hauke Mehrtens
d80336e1a9 busybox: Fix snprintf arguments in lock
The first argument for snprintf is the buffer and the 2. one is the
size. Fix the order. This broke the lock application.

Fixes: 34567750db ("busybox: fix busybox lock applet pidstr buffer overflow")
Reported-by: Hartmut Birr <e9hack@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2022-03-31 18:46:53 +02:00
Petr Štetiar
f389831db6 kernel: modules: fix kmod-drm-imx-ldb dependency for 5.15
Fixes following issue:

 Package kmod-drm-imx-ldb is missing dependencies for the following libraries:
 drm_dp_aux_bus.ko

Introduced upstream in commit aeb33699fc2c ("drm: Introduce the DP AUX
bus") in kernel version 5.15.

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2022-03-31 17:30:17 +02:00
Petr Štetiar
f5a54716a4 kernel: modules: fix kmod-drm dependency for 5.15
Fixes following issue:

 Package kmod-drm is missing dependencies for the following libraries:
 fb.ko

Introduced upstream in commit f611b1e7624c ("drm: Avoid circular
dependencies for CONFIG_FB") in 5.14.

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2022-03-30 23:39:08 +02:00
Qichao Zhang
34567750db busybox: fix busybox lock applet pidstr buffer overflow
Kernel setting `/proc/sys/kernel/pid_max` can be set up to 4194304 (7
digits) which will cause buffer overflow in busbox lock patch, this
often happens when running in a rootfs container environment.
This commit enlarges `pidstr` to 12 bytes to ensure a sufficient buffer
for pid number and an additional char '\n'.

Signed-off-by: Qichao Zhang <njuzhangqichao@gmail.com>
2022-03-30 18:33:38 +02:00
Felix Fietkau
5e34b316c5 mt76: update to the latest version
eed44048ca57 Revert "mt76: dma: reduce lock contention in mt76_dma_tx_cleanup"

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-03-29 18:35:34 +02:00
Petr Štetiar
be9a69caa8 kernel: modules: fix kmod-mdio-devres dependency for 5.15
Fixes following build issues:

 Package kmod-r8169 is missing dependencies for the following libraries:
 mdio_devres.ko

 Package kmod-ixgbe is missing dependencies for the following libraries:
 mdio_devres.ko

 Package kmod-amd-xgbe is missing dependencies for the following libraries:
 mdio_devres.ko

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2022-03-29 12:02:50 +02:00
Felix Fietkau
103ad908c2 mt76: update to the latest version
65042bfd759c mt76: mt7915: introduce 802.11ax multi-bss support
e756ea3bd069 mt76: fix wrong HE data rate in sniffer tool
47b64131e820 mt76: mt7921: don't enable beacon filter when IEEE80211_CONF_CHANGE_MONITOR is set
7a05f4628e76 mt76: fix monitor rx FCS error in DFS channel
104dd5cb0a40 mt76: mt7915: fix DBDC default band selection on MT7915D
a7805e4e1d58 mt76: reduce tx queue lock hold time
0b1deb9292cd mt76: dma: use kzalloc instead of devm_kzalloc for txwi
2e51013b38c9 mt76: dma: reduce lock contention in mt76_dma_tx_cleanup
c96fbb86f7e5 mt76: mt7915: rework hardware/phy initialization
c2bb44cab51e mt76: mt7915: accept rx frames with non-standard VHT MCS10-11
36c23a4a8422 mt76: mt7921: accept rx frames with non-standard VHT MCS10-11
5b7dd093c8f0 mt76: fix use-after-free by removing a non-RCU wcid pointer
c692aacb9bde mt76: fix MBSS index condition in DBDC mode
fd6541905aa4 mt76: mt7921u: add suspend/resume support
201b33cf42c2 mt76: mt7921: rely on mt76_dev rxfilter in mt7921_configure_filter
9666c08228e7 mt76: mt7921: honor pm user configuration in mt7921_sniffer_interface_iter
1442710d7936 mt76: mt7915: always call mt7915_wfsys_reset() during init
ec4d9b9e8b70 mt76: mt7915: fix unbounded shift in mt7915_mcu_beacon_mbss
6b1efcd72946 mt76: mt7915: fix wfsys reset regression
376ea8152b2b mt76: mt7915: add missing chunk from wfsys reset fix

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-03-28 13:25:00 +02:00
John Thomson
f65596e8a9 kernel: 5.15: fix mediatek usb module change
The mediatek USB kernel module xhci-mtk was restructed.
The module after kernel 5.13 is named xhci-mtk-hcd.
Link:
https://lore.kernel.org/all/0b62e21ddfacc1c2874726dd27ccab80c993f303.1615170625.git.chunfeng.yun@mediatek.com/
Linux 14295a150050 ("usb: xhci-mtk: support to build xhci-mtk-hcd.ko")

Signed-off-by: John Thomson <git@johnthomson.fastmail.com.au>
2022-03-28 11:03:13 +02:00
Felix Fietkau
3f8ea009d0 kernel: add missing nls dependency for kmod-fs-ntfs3
This showed up on a linux 5.15 build

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-03-28 11:03:13 +02:00
Jason A. Donenfeld
2edc017a6e urandom-seed: use seedrng for seeding the random number generator
The RNG can't actually be seeded from a shell script, due to the
reliance on ioctls. For this reason, the seedrng project provides a
basic script meant to be copy and pasted into projects like OpenWRT
and tweaked as needed: <https://git.zx2c4.com/seedrng/about/>.

This commit imports it into the urandom-seed package and wires up the
init scripts to call it. This also is a significant improvement over the
current init script, which does not robustly handle cleaning up of seeds
and syncing to prevent reuse. Additionally, the existing script creates
a new seed immediately after writing an old one, which means that the
amount of entropy might actually regress, due to failing to credit the
old seed.

Closes: https://github.com/openwrt/openwrt/issues/9570
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz> [fixed missing INSTALL_DIR]
2022-03-28 09:27:56 +02:00
Petr Štetiar
3eb777e180 libs/zlib: fix implicit function declaration warning
Fixes following warning:

 adler32.c:141:12: warning: implicit declaration of function 'NEON_adler32' [-Wimplicit-function-declaration]
   141 |     return NEON_adler32(adler, buf, len);

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2022-03-28 09:27:56 +02:00
Petr Štetiar
8839a939ee libs/zlib: bump to latest stable release 1.2.12 (CVE-2018-25032)
List of changes since previous release from 2018 is quite long:

 * Fix crc32.c to compile local functions only if used.
 * Check for cc masquerading as gcc or clang in configure.
 * Remove destructive aspects of make distclean.
 * Separate out address sanitizing from warnings in configure.
 * Eliminate use of ULL constants.
 * Add fallthrough comments for gcc.
 * Clean up minizip to reduce warnings for testing.
 * Fix unztell64() in minizip to work past 4GB. (Daniël Hörchner)
 * minizip warning fix if MAXU32 already defined. (gvollant)
 * Replace black/white with allow/block. (theresa-m)
 * Fix indentation in minizip's zip.c.
 * Improve portability of contrib/minizip.
 * Correct typo in blast.c.
 * Change macro name in inflate.c to avoid collision in VxWorks.
 * Clarify gz* function interfaces, referring to parameter names.
 * Fix error in comment on the polynomial representation of a byte.
 * Fix memory leak on error in gzlog.c.
 * Avoid adding empty gzip member after gzflush with Z_FINISH.
 * Explicitly note that the 32-bit check values are 32 bits.
 * Use ARM crc32 instructions if the ARM architecture has them.
 * Add use of the ARMv8 crc32 instructions when requested.
 * Correct comment in crc32.c.
 * Don't bother computing check value after successful inflateSync().
 * Use atomic test and set, if available, for dynamic CRC tables.
 * Speed up software CRC-32 computation by a factor of 1.5 to 3.
 * Add crc32_combine_gen() and crc32_combine_op() for fast combines.
 * Add tables for crc32_combine(), to speed it up by a factor of 200.
 * Fix the zran.c example to work on a multiple-member gzip file.
 * Add gznorm.c example, which normalizes gzip files.
 * Show all the codes for the maximum tables size in enough.c.
 * Clarify that prefix codes are counted in enough.c.
 * Use inline function instead of macro for index in enough.c.
 * Clean up code style in enough.c, update version.
 * Use a macro for the printf format of big_t in enough.c.
 * Use a structure to make globals in enough.c evident.
 * Assure that the number of bits for deflatePrime() is valid.
 * Fix a bug that can crash deflate on some input when using Z_FIXED.
 * Correct the initialization requirements for deflateInit2().
 * Emphasize the need to continue decompressing gzip members.
 * Add legal disclaimer to README.
 * Fix deflateEnd() to not report an error at start of raw deflate.
 * Remove old assembler code in which bugs have manifested.
 * Make the names in functions declarations identical to definitions.
 * Avoid an undefined behavior of memcpy() in _tr_stored_block().
 * Avoid undefined behaviors of memcpy() in gz*printf().
 * Avoid an undefined behavior of memcpy() in gzappend().
 * Avoid the use of ptrdiff_t.
 * Handle case where inflateSync used when header never processed.
 * Don't compute check value for raw inflate if asked to validate.
 * Add address checking in clang to -w option of configure.
 * Return an error if the gzputs string length can't fit in an int.
 * Small speedup to inflate [psumbera].
 * Update use of errno for newer Windows CE versions.
 * Avoid some conversion warnings in gzread.c and gzwrite.c.
 * Have Makefile return non-zero error code on test failure.
 * Avoid a conversion error in gzseek when off_t type too small.
 * Fix CLEAR_HASH macro to be usable as a single statement.
 * Fix bug when window full in deflate_stored().
 * Limit hash table inserts after switch from stored deflate.
 * Permit a deflateParams() parameter change as soon as possible.
 * Cygwin does not have _wopen(), so do not create gzopen_w() there.

Removed 006-fix-compressor-crash-on-certain-inputs.patch which was
hotfix for CVE-2018-25032 and is now included in this release.

This release is not available on @SF (yet?) so the sources are now
pulled from GitHub.

Fixes: CVE-2018-25032
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2022-03-28 09:27:56 +02:00
Daniel Golle
f667277dd0
kernel: 5.15: add missing Kconfig symbols for NFS
Add new Kconfig symbols for NFSv4.1 and NFSv4.2 to kmod-nfs-common and
kmod-nfsd.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-03-27 14:50:59 +01:00
Christian Lamparter
eeb8fd4ce7 gpio-cdev: move kmod-leds-uleds dependency to MX100
The inclusion of the kmod-leds-uleds into the userspace
nu801 package causes a circular dependency inside the
buildsystem... which causes it to be picked regardless
of other DEPENDS values.

In case of the mx100, this could be solved by moving the
kmod-leds-uled dependency to the kmod-meraki-mx100.

Bonus: drop @!LINUX_5_4 from kmod-meraki-mx100
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-03-27 15:39:27 +02:00
Christian Lamparter
7368345450 gpio-cdev: provide HASH values for nu801
Chen Minqiang reported that he has troubles downloading nu801.
His logs showed the followin TLS Handshake failure.

|Checking out files from the git repository...
|Cloning into 'nu801-d9942c0c'...
|fatal: unable to access 'https://github.com/chunkeey/nu801.git/':
|  gnutls_handshake() failed: The TLS connection was non-properly terminated.
|Makefile:39: recipe for target '[...]/dl/nu801-d9942c0c.tar.xz' failed

This can be fixed by providing a PKG_MIRROR_HASH. The download
scripts will now be able to pull the source from OpenWrt's source
archive, which should be available through HTTP.

Reported-by: Chen Minqiang <ptpt52@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-03-27 15:38:51 +02:00
Rosen Penev
8a5d095969 elfutils: fix host compilation with Alpine Linux
intl is not included in libc, disable it as is done with the target
package.

argp is also not included. Add build depends for argp-standalone.

fts is also not included. Add build depends for musl-fts.

Disable shared libraries to avoid having to manually add rpath.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2022-03-27 14:38:13 +02:00
Rosen Penev
f8571749a7 pcre: disable shared libraries for host builds
Getting rid of shared libraries for hostpkg avoids having to use rpath
hacks to find the library. It also fixes compilation with host glib2
binaries.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2022-03-27 14:38:13 +02:00
Rosen Penev
8a75ed4ba0 musl-fts: remove shared libraries from host
Avoids having to add rpath to the various packages using it. Also add
PIC to fix compilation as static libraries do not use PIC by default.

Fixes: 1fb099341e ("musl-fts: add host build")
Signed-off-by: Rosen Penev <rosenp@gmail.com>
2022-03-27 14:38:13 +02:00
Ansuel Smith
bd0db6017b kernel: 5.15: add new module
Add new module require in 5.15
- Changes in block module
- Changes in netfilter module (log module unified)
- Changes in fs module (mainly new depends for cifs and new ntfs3 module)
- Changes in lib add shared lib now used by more than 1 kmod
- Changes in crypto, dropped one crypto algo added arm crypto accellerator
- Changes in other, add zram default compressor choice and missing lib
  by tpm module

Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
2022-03-27 02:17:24 +01:00
Felix Fietkau
56ae4eb908 mac80211: backport patch that allows receiving packets with non-standard VHT MCS10-11 rates
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-03-25 21:11:09 +01:00
张 鹏
bdc786e82c ipq40xx: update E2600AC c1/c2 board
Modified the radio frequency hardware part of e2600ac c1/c2,
need to cooperate with the modified board.bin file, the device
can work normally.

Signed-off-by: 张 鹏 <sd20@qxwlan.com>
2022-03-25 18:14:13 +01:00
Josef Schlehofer
51dee3f4f7 cypress-firmware: drop several packages
1. Drop package: cypress-firmware-4359-pcie
This binary is no longer provided and there are not many details what
happened.

2. Drop package: cypress-firmware-4359-sdio
This binary is no longer provided, but in this case, to compare it with
PCIe package mention as first, there was added
support in Linux-firmware [1], but no sign of firmware file.

4. Drop package: cypress-firmware-89459-pcie [2]
According to Infineon: "CYW89459 is an automotive Wi-Fi chip which is not
supported in the broad market community."

[1] https://patchwork.kernel.org/project/linux-wireless/patch/20191211235253.2539-6-smoch@web.de/

[2] https://community.infineon.com/t5/Wi-Fi-Bluetooth-for-Linux/the-wifi-driver-for-CYW89459-in-linux4-14-98-2-3-00/m-p/138971

Fixes: 7ca7e0b22d ("cypress-firmware: update it to version 5.4.18-2021_0812")

Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
2022-03-25 18:14:13 +01:00
Chris Blake
3f874519b4 gpio-cdev: re-add nu801 userspace driver
This reverts commit 80b7a8a7f5.

Now that 5.10 is the default kernel for all platforms, we can
bring back the NU801 userspace driver for platforms that rely
on it. Currently it's used on the MX100 x86_64 target, but
other Meraki platforms use this controller.

Note that we also now change how we load nu801. The way we did
this previously with procd worked, but it meant it didn't load
until everything was up and working.

To fix this, let's call nu801 from boot and re-trigger the
preinit blink sequence. Since nu801 runs as a daemon this is
now something we can do.

Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
(removed empty line, currently only MX100 uses it so: @TARGET_x86)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-03-25 18:14:13 +01:00
Brian Norris
17b05045bd ipq40xx: Support Chromium OS image-type creation
See firmware-utils.git commits [1], which implemented the cros-vbutil
verified-boot payload-packing tool, and extended ptgen for the CrOS
kernel partition type. With these, it's now possible to package kernel +
rootfs to make disk images that can boot a Chrome OS-based system (e.g.,
Chromebooks, or even a few AP models).

Regarding PARTUUID= changes: Chromium bootloaders work well with a
partition number offset (i.e., relative to the kernel partition), so
we'll be using a slightly different root UUID line.

NB: I've made this support specific to ip40xx for now, because I only
plan to support an IPQ4019-based AP that uses a Chromium-based
bootloader, but this image format can be used for essentially any
Chromebook, as well as the Google OnHub, a prior Chromium-based AP using
an IPQ8064 chipset.

[1]
ptgen: add Chromium OS kernel partition support
https://git.openwrt.org/?p=project/firmware-utils.git;a=commit;h=6c95945b5de973026dc6f52eb088d0943efa96bb

cros-vbutil: add Chrome OS vboot kernel-signing utility
https://git.openwrt.org/?p=project/firmware-utils.git;a=commit;h=8e7274e02fdc6f2cb61b415d6e5b2e1c7e977aa1

Signed-off-by: Brian Norris <computersforpeace@gmail.com>
2022-03-25 18:14:13 +01:00
Brian Norris
331d78a90f firmware/ipq-wifi: Add Google Wifi board-2.bin
From a manufacturer's image (version R89-13729.57.27), with appopriate
',variant=' appended to the board names:

  $ .../qca-swiss-army-knife/tools/scripts/ath10k/ath10k-bdencoder \
        -i ./board-google_wifi.qca4019
  FileSize: 48596
  FileCRC32: 3966df5d
  FileMD5: d54161b0fb9e93691c4272649c37535a
  BoardNames[0]: 'bus=ahb,bmi-chip-id=0,bmi-board-id=16,variant=GO_GALE'
  BoardLength[0]: 12064
  BoardCRC32[0]: e117f336
  BoardMD5[0]: ea35e78c88a8571201da8b75edc9b881
  BoardNames[1]: 'bus=ahb,bmi-chip-id=0,bmi-board-id=21,variant=GO_GALE'
  BoardLength[1]: 12064
  BoardCRC32[1]: 6c751ec9
  BoardMD5[1]: 44cbc4ca6cb7141ba4249615f7065582
  BoardNames[2]: 'bus=ahb,bmi-chip-id=0,bmi-board-id=16,variant=GO_BREEZE'
  BoardLength[2]: 12064
  BoardCRC32[2]: 24fba117
  BoardMD5[2]: b4ac055b3ab67d5a6f5607a96af39a1f
  BoardNames[3]: 'bus=ahb,bmi-chip-id=0,bmi-board-id=21,variant=GO_BREEZE'
  BoardLength[3]: 12064
  BoardCRC32[3]: a3e16b2a
  BoardMD5[3]: 8b26cb285032314247304114b8ac50e7

Naming follows existing Google projects included in upstream board-2.bin
-- GO(ogle) prefix, an underscore (_), and the project code name, all in
caps.

Note that I only tested the "gale" model; the "breeze" model is a later
revision (same marketing name) with very small hardware changes but
otherwise using the same firmware image.

Submitted upstream here:

  ath10k-firmware: QCA4019: hw1.0: Add Google Wifi BDFs
  http://lists.infradead.org/pipermail/ath10k/2022-March/013465.html
  https://lore.kernel.org/ath10k/YjaNGW252Ls%2FyDw8@localhost/

Signed-off-by: Brian Norris <computersforpeace@gmail.com>
2022-03-25 18:14:13 +01:00
Brian Norris
e5b009e532 kernel: Package GOOGLE_FIRMWARE drivers
Useful for some Chromium OS based systems, like Google WiFi.

Signed-off-by: Brian Norris <computersforpeace@gmail.com>
2022-03-25 18:14:13 +01:00
Rosen Penev
abb2683de3 libselinux: use musl-fts for host builds
Fixes compilation under musl based distros like Alpine Linux.

Also add pcre/host as a build dependency as it's needed.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2022-03-25 18:14:13 +01:00
Rosen Penev
1fb099341e musl-fts: add host build
This will be used for libselinux.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2022-03-25 18:14:13 +01:00
Stijn Tintel
636cb00ecc gettext-full: add gmsgfmt symlink in host install
Some configure scripts look for msgfmt and gmsgfmt. As we don't install
the latter, configure might pick up one from staging_dir/hostpkg, and
the other from the host:

checking for msgfmt... /home/stijn/Development/OpenWrt/openwrt/staging_dir/hostpkg/bin/msgfmt
checking for gmsgfmt... /usr/bin/gmsgfmt

This could potentially lead to hard to debug undefined behaviour.
Install a symlink in the host install phase to avoid this.

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2022-03-25 17:48:49 +02:00
Petr Štetiar
759886345d openwrt-keyring: add OpenWrt 22.03 GPG/usign keys
62471e693b4f usign: add 22.03 release build public key
 70817cffc905 gpg: add OpenWrt 22.03 signing key

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2022-03-25 14:28:00 +01:00
Daniel Golle
ee7cb5e885
uqmi: fix acquiring PIN status
Evaluating the return value of 'json_load' didn't work in the
intended way resulting in PIN status no longer being read on modems
where --get-pin-status doesn't fail.
Fix this by trying --get-pin-status first and checking if pin1_status
field exists in JSON, and if it doesn't try again with
--uim-get-sim-state.

Fixes: #9501
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-03-24 18:45:19 +00:00
Petr Štetiar
b3aa2909a7 zlib: backport security fix for a reproducible crash in compressor
Tavis has just reported, that he was recently trying to track down a
reproducible crash in a compressor. Believe it or not, it really was a
bug in zlib-1.2.11 when compressing (not decompressing!) certain inputs.

Tavis has reported it upstream, but it turns out the issue has been
public since 2018, but the patch never made it into a release. As far as
he knows, nobody ever assigned it a CVE.

Suggested-by: Tavis Ormandy <taviso@gmail.com>
References: https://www.openwall.com/lists/oss-security/2022/03/24/1
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2022-03-24 08:15:24 +01:00
Eneas U de Queiroz
1bf94b6797 openssl: move engine.mk to INCLUDE_DIR
engine.mk is supposed to be included by engine packages, but it will not
be present in the SDK in the same place as in the main repository.

Move it to include/openssl-engine.mk to avoid this.

Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
2022-03-23 23:13:51 +00:00
Hans Dedecker
73c6d8fd04 odhcpd: update to git HEAD
860ca90 odhcpd: Support for Option NTP and SNTP
83e14f4 router: advertise removed addresses as invalid in 3 consecutive RAs

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
2022-03-22 22:03:37 +01:00
Felix Fietkau
af434e0da2 qosify: update to the latest version
57c7817f91c2 qosify: fix dscp values of ubus-added dns host entries

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-03-22 10:28:28 +01:00