Remove 980-rt2x00-reduce-power-consumption-on-mt7620.patch which in
combination with the most recently added patch reportedly causes TX
power to be too weak.
"without patches rssi on receiver is ~ -23dBm with 980 about -35dBm,
with both patches drops below -40dBm. with 987 only ~-28dBm"
We may need to reconsider this once we have implemented TSSI.
Fixes: cdb58b2bfe ("mac80211: rt2x00: reduce tx power to nominal level on RT6352")
Reported-by: Tomislav Požega <pozega.tomislav@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Fixed CVEs:
CVE-2018-16890
CVE-2019-3822
CVE-2019-3823
For other changes in version 7.64.0 see https://curl.haxx.se/changes.html#7_64_0
Signed-off-by: Deng Qingfang <dengqf6@mail2.sysu.edu.cn>
Current implementation of RT6352 support provides too high tx power
at least on iPA/eLNA devices. Reduce amplification of variable gain
amplifier by 6dB to match board target power of 17dBm.
Transmited signal strength with this patch is similar to that of
stock firmware or pandorabox firmware. Throughput measured with iperf
improves. Device tested: Xiaomi Miwifi Mini.
Signed-off-by: Tomislav Požega <pozega.tomislav@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
There are two problems with this behaviour that the zone is set to wan
if no zone config option is defined in the interface section.
* The zone for the interface is "normally" specified in the firewall
config file. So if we have defined "no" zone for this interface zone
option is set now to "wan" additonaly if we add the interface in the firewall
config section to the "lan" zone, the interface is added to lan and wan at once.
iptables-save | grep <iface>
This is not what I expect.
* If I do not want to set a zone to this interface it is not possible.
Remove the default assigment to wan if no zone option is defined.
If some one need the option it stil possible to define this option.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com> [PKG_RELEASE increase]
On ath79 and UBNT Bullet M XW (ar9342) I was experiencing weird issues during
network setup[1] which I was able to reproduce easily with following commands:
uci set network.lan.ipaddr='192.168.1.20'
uci commit network
ifup lan
Which resulted after some time in:
...
WARNING: CPU: 0 PID: 0 at net/sched/sch_generic.c:461 dev_watchdog+0x16c/0x280
NETDEV WATCHDOG: eth0 (ag71xx): transmit queue 0 timed out
...
Sometimes I wasn't able to use networking anymore, sometimes it was enough to
just ifdown/ifup lan and network was backup. On ar71xx it was all working just
fine.
I've found out, that it was happening because ag71xx_poll() wasn't called, thus
the TX queue wasn't emptied. The ag71xx_poll() is being called from napi
hrtimer, which is enabled by napi_schedule() in ar71xx_interrupt(), but since
no interrupts were ever fired again after ag71xx_stop() was called, it was
always leading to tx queue timeouts:
*** ag71xx_hard_start_xmit()
eth0: packet injected into TX queue
eth0: raw intr=00000001 TXPS POLL
eth0: enable polling mode
eth0: processing TX ring, flush=no
eth0: disable polling mode, rx=1, tx=1,limit=32
( `ifup lan done here` )
*** ag71xx_stop()
*** ag71xx_open()
*** ag71xx_hw_enable()
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
*** ag71xx_hard_start_xmit()
eth0: packet injected into TX queue
*** ag71xx_hard_start_xmit()
eth0: packet injected into TX queue
...
WARNING: CPU: 0 PID: 0 at net/sched/sch_generic.c:320 dev_watchdog+0x164/0x274
So I've looked at ag71xx_stop() in ar71xx, added the missing bits to ath79 and
fixed this issue.
1. https://github.com/openwrt/openwrt/pull/1635#issuecomment-448638246
Signed-off-by: Petr Štetiar <ynezz@true.cz>
[move ag->link before ag71xx_hw_disable to retain ordering as original]
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
The package hash does not match the one of the package found on the
mirrors and which is generated when I do the git clone.
Fixes: 4856fa30a6 ("nat46: import for routing, add myself as maintainer")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Restoring the bootloader config before rebooting fails:
tar: invalid tar magic
Add the -z option to the tar command to fix this.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
TP-Link Archer C7 v4 is a dual-band AC1750 router, based on the
Qualcomm/Atheros QCA9561 SoC + QCA9880.
Specification:
- 775/650/258 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 3T3R 5 GHz
- 5x 10/100/1000 Mbps Ethernet
- 7x LED, 2x button
- UART header on PCB
Flash instruction:
1. Upload openwrt-ath79-generic-tplink_archer-c7-v4-squashfs-factory.bin
via Web interface
Flash instruction using TFTP recovery:
1. Set PC to fixed ip address 192.168.0.66
2. Download openwrt-ath79-generic-tplink_archer-c7-v4-squashfs-factory.bin
and rename it to ArcherC7v4_tp_recovery.bin
3. Start a tftp server with the file tp_recovery.bin in its root directory
4. Turn off the router
5. Press and hold Reset button
6. Turn on router with the reset button pressed and wait ~15 seconds
7. Release the reset button and after a short time
the firmware should be transferred from the tftp server
8. Wait ~30 second to complete recovery.
Signed-off-by: Oldřich Jedlička <oldium.pro@gmail.com>
It was reported to me today on IRC, that building of artifacts doesn't
work properly if the concat_cmd references DEVICE_NAME variable. I've
found out, that it's due to missing call of Device/Export in artifacts
building code path, so this patch adds the missing Device/Export call
which in turn exports DEFAULT_DEVICE_VARS into the artifacts
environment.
Fixes: 493c9a3551 ("build: Introduce building of artifacts")
Tested-by: Oskari Lemmela <oskari@lemmela.net>
Reported-by: Oskari Lemmela <oskari@lemmela.net>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This option was a spi nor hack which is dropped in commit
bcf4a5f474 ("ramips: remove chunked-io patch and set spi->max_transfer_size instead")
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [edit message]
The WeVo 11AC NAS has a MT7612E 802.11ac chip on the PCB.
Signed-off-by: Ju Se Hoon <joosahoon@gmail.com>
[renamed author from Albis-dev to real name, editted commit message]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
<https://www.openwall.com/lists/musl/2019/01/21/8>
"This release makes improvements with respect to default thread stack
size, including increasing the default from 80k to 128k, increasing
the default guard size from 4k to 8k, and allowing the default to be
increased via ELF headers so that programs that need larger stacks can
be build without source-level changes, using just LDFLAGS.
Insufficient stack size for AIO threads on kernels that don't honor
the constant MINSIGSTKSZ is also fixed.
The glob core has been rewritten to fix inability to see past
searchable-but-unreadable path components, and to avoid excessive
stack usage and unnecessary syscalls. The tsearch AVL tree
implementation has also been rewritten for better size and
performance. The math library adds more native single-instruction
implementations for arm, s390x, powerpc, and x86_64.
Various bugs are fixed, including several possible deadlocks, one of
which was a new regression in 1.1.20."
detailed release notes can be found in the WHATSNEW file:
<http://git.musl-libc.org/cgit/musl/tree/WHATSNEW#n1989>
Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch fixes the ASUS' RT-AC58U port order by
unifying the configuration with the NBG6617.
Reported-by: Roberto Socrates (rtac58u-user on the forum)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch splits the big board case switch in 02_network in
two functions ipq40xx_setup_interfaces() and ipq40xx_setup_macs()
just like ath79 and ramips do.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* Jan 2, 2019
Rebase patches to make 9980 bisectable.
* Jan 2, 2019
Fix scheduling related assert when wal-peer is deleted with pending
tx buffers (bug 54, and others)
* Jan 7, 2019:
Fix specifying retransmits for AMPDU frames. It was previously ignored
since it is a 'software' retransmit instead of a hardware retransmit.
* Jan 9, 2019
Fix potential way to get zero rates selected (and then assert)
* Jan 18, 2019
pfsched has specific work-around to just return if we find invalid flags AND
if we are in an out-of-order situation. Maybe this is last of the pfsched
related issues (bug 54 and similar).
* Jan 24, 2019
The rcSibUpdate method can be called concurrently with IRQ tx-completion callback,
and that could potentially allow the tx-completion callback to see invalid state
and assert or otherwise mess up the rate-ctrl logic. So, disable IRQs in
rcSibUpdate to prevent this. Related to bug 58.
* Jan 28, 2019
Ensure that cached config is applied to ratectrl objects when fetched from
the cache. This should fix part of bug 58.
* Jan 28, 2019
Ensure that ratectrl objects from cachemgr are always initialized. This fixes
another part of bug 58.
* Jan 30, 2019
Better use of temporary rate-ctrl object. Make sure it is initialized, simplify
code path. This finishes up porting forward similar changes I made for wave-1
firmware long ago, and fixes another potential way to hit bug-58 issues.
* Jan 30, 2019
Cachemgr did not have a callback for when memory was logically freed. This means
that peers could keep stale references to rate-ctrl objects that were in process
of being DMA'd into to load a different peer's rate-ctrl state. This was causing
the bugcheck logic to fail early and often, and I suspect it might be a root cause
of bug 58 as well. The fix is to add a callback and set any 'deleted' memory references
to NULL so that we cannot access it accidentally. Thanks to excellent logs and patience
from the bug-58 reporter!
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Commit e61061a088 added support for hardening
options in the toolchain. However this breaks the gcc5.5.0 compilation in
case FORTIFY_SOURCE is set different from FORTIFY_SOURCE_NONE as reported
in [1].
Fix this by backporting the upstream patch which fixes this in later gcc versions
[1] https://gcc.gnu.org/bugzilla/show_bug.cgi?format=multiple&id=61164
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
a9d4c0e mt76: mt76x2: avoid running DPD calibration if tx is blocked
4d7e13f mt76: explicitly disable energy detect cca during scan
e3c1aad mt76: run MAC work every 100ms
4e8766a mt76: clear CCA timer stats in mt76x02_edcca_init
e301f23 mt76: measure the time between mt76x02_edcca_check runs
74075ef mt76: increase ED/CCA tx block threshold
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Package kmod-drm is missing dependencies for the following libraries:
drm_panel_orientation_quirks.ko
It seems, that since Linux 4.15-rc2 drm depends on drm_panel_orientation_quirks.ko
commit 8d70f395e6cbece665b12b4bf6dbc48d12623014
Author: Hans de Goede <j.w.r.degoede@gmail.com>
Date: Sat Nov 25 20:35:49 2017 +0100
drm: Add support for a panel-orientation connector property, v6
On some devices the LCD panel is mounted in the casing in such a way that
the up/top side of the panel does not match with the top side of the
device (e.g. it is mounted upside-down).
This commit adds the necessary infra for lcd-panel drm_connector-s to
have a "panel orientation" property to communicate how the panel is
orientated vs the casing.
Userspace can use this property to check for non-normal orientation and
then adjust the displayed image accordingly by rotating it to compensate.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
a4ec45c mt7603: fix LED support (copy CFLAGS from main Makefile)
edda5c5 mt76x02: use mask for vifs
dd52191 mt76x02: use commmon add interface for mt76x2u
a80acaf mt76x02: initialize mutli bss mode when set up address
38e832d mt76x02: minor beaconing init changes
171adaf mt76x02: init beacon config for mt76x2u
dcab682 mt76: beaconing fixes for USB
ff81de1 mt76x02: enable support for IBSS and MESH
8027b5d mt7603: remove copyright headers
e747e80 mt76: fix software encryption issues
2afa0d7 mt7603: remove WCID override for software encrypted frames
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Host "gd.tuwien.ac.at" does not exists anymore, so we replace it by "ftp.pca.dfn.de" from the official list of mirrors.
Signed-off-by: Sven Roederer <devel-sven@geroedel.de>
Use `stat -L` instead of `ls -l` to follow symbolic links when obtaining
the file size of .ipk archives.
Without this change, the size of the symlink, not the size of the target
file is encoded in the package index file.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
d4ba162 libopkg: only perform size check when information is available
Fixes: e079591b84 ("opkg: update to latest Git head")
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
c3da1aa mt7603: trigger beacon stuck detection faster
7a53138 mt7603: trigger watchdog reset if flushing CAB queue fails
6eef33b mt7603: remove mt7603_txq_init
ae30c30 mt76: add driver callback for when a sta is associated
0db925f mt7603: update HT/VHT capabilities after assoc
b5ac8e4 mt7603: initialize LED callbacks only if CONFIG_MT76_LEDS is set
c989bac mt76x0: eeprom: fix chan_vs_power map in mt76x0_get_power_info
24bd2c0 mt76x0: phy: report target_power in debugfs
bc7ce2a mt76x0: init: introduce mt76x0_init_txpower routine
Signed-off-by: Felix Fietkau <nbd@nbd.name>
When config_get is called as "config_get section option" the option
is unexpectedly globbed by the shell which differs from the way options
are read to a variable with "config_get variable section option".
Add another layer of double quotes to fix it.
Signed-off-by: Günther Kelleter <guenther.kelleter@devolo.de>
Use LINUX_DIR as a path when patching kernel. Doesn't break the current usage,
but allows to create packages that will contain variation of a kernel with
kernel being build in some subdirectory of PKG_BUILD_DIR.
Signed-off-by: Michal Hrusecky <michal.hrusecky@nic.cz>
Building ar71xx currently fails with:
In file included from ./include/linux/ipv6.h:5,
from ./include/net/ipv6.h:16,
from ./include/net/inetpeer.h:16,
from ./include/net/ip_fib.h:24,
from ./include/net/switchdev.h:17,
from ./include/net/dsa.h:23,
from arch/mips/ath79/dev-dsa.h:15,
from arch/mips/ath79/dev-dsa.c:17:
./include/uapi/linux/ipv6.h:107:1: error: alignment 1 of 'struct ipv6_destopt_hao' is less than 2 [-Werror=packed-not-aligned]
} __attribute__((packed));
Address this issue by correcting the alignment of the struct packing
pragma accordingly.
Fixes: FS#1805
Reported-by: Pascal Ernster <git@hardfalcon.net>
[reword subject, rewrap commit message]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
This fixes two issues with cleaning package files from STAGING_DIR:
* CleanStaging currently can only remove files and not directories. This
changes CleanStaging to use clean-package.sh, which does remove
directories.
* Because of the way directories are ordered in the staging files list,
clean-package.sh currently tries (and fails) to remove parent
directories before removing subdirectories. This changes
clean-package.sh to process the staging files list in reverse, so that
subdirectories are removed first.
Signed-off-by: Jeffery To <jeffery.to@gmail.com>
If a user finds that logd is too barebone for their needs and wishes
to have more control over syslog, the user presently has an option
to enable CONFIG_BUSYBOX_CONFIG_FEATURE_SYSLOG and configure syslog
with settings in /etc/syslog.conf.
Presently /etc/syslog.conf silently disappears on sysupgrade. This
patch prevents such unwanted behaviour if busybox syslog is enabled
via CONFIG_BUSYBOX_CONFIG_FEATURE_SYSLOG.
Signed-off-by: Val Kulkov <val.kulkov@gmail.com>
The correct MAC address for this device is lan_mac +1, there is no
need to set lan_mac so use base_mac variable instead lan_mac.
Based on this PR for ath79:
https://github.com/openwrt/openwrt/pull/1726
Signed-off-by: David Santamaría Rogado <howl.nsp@gmail.com>
[fix alphabetical ordering, reword subject]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
