There was a typo in commit 5709254690 ("mediatek: bpi-r4: store random
MAC addresses for the BPi-R4"). Let's fix it and also add support for
the bpi-r4-poe variant.
Fixes: 5709254690 ("mediatek: bpi-r4: store random MAC addresses for the BPi-R4")
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Despite coming with multiple I2C EEPROMs supposedly dedicated for that
purpose, the BPi-R4 does not seem to have factory assigned MAC addresses.
Hence, just like for all other BPi boards, store a randomly generated
MAC address on first boot and derive WAN and Wi-Fi MAC addresses from
that as well. Not perfect, but better than random on every boot.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Hardware specification
----------------------
SoC: MediaTek MT7986A 4x A53
Flash: 128MB SPI-NAND, 8GB eMMC
RAM: 2GB DDR4
Ethernet: 2x 2.5GbE (Airoha EN8811H)
WiFi: MediaTek MT7976C 2x2 2.4G + 3x3 5G
Interfaces:
* M.2 Key-M: PCIe 2.0 x2 for NVMe SSD
* M.2 Key-B: USB 3.0 with SIM slot
* front USB 2.0 port
LED: Power, Status, WLAN2G, WLAN5G, LTE, SSD
Button: Reset, internal boot switch
Fan: PWM-controlled 5V fan
Power: 12V Type-C PD
Installation instructions for eMMC
----------------------------------
0. Set boot switch to boot from SPI-NAND (assuming stock rom or immortalwrt
running there).
1. Write GPT partition table to eMMC
Move openwrt-mediatek-filogic-bananapi_bpi-r3-mini-emmc-gpt.bin to
the device /tmp using scp and write it to /dev/mmcblk0:
dd if=/tmp/openwrt-*-r3-mini-emmc-gpt.bin of=/dev/mmcblk0
2. Reboot (to reload partition table)
3. Write bootloader and OpenWrt images
Move files to the device /tmp using scp:
- openwrt-*-bananapi_bpi-r3-mini-emmc-preloader.bin
- openwrt-*-bananapi_bpi-r3-mini-emmc-bl31-uboot.fip
- openwrt-*-bananapi_bpi-r3-mini-initramfs-recovery.itb
- openwrt-*-bananapi_bpi-r3-mini-squashfs-sysupgrade.itb
Write them to the appropriate partitions:
echo 0 > /sys/block/mmcblk0boot0/force_ro
dd if=/tmp/openwrt-*-bananapi_bpi-r3-mini-emmc-preloader.bin of=/dev/mmcblk0boot0
dd if=/tmp/openwrt-*-bananapi_bpi-r3-mini-emmc-bl31-uboot.fip of=/dev/mmcblk0p3
dd if=/tmp/openwrt-*-bananapi_bpi-r3-mini-initramfs-recovery.itb of=/dev/mmcblk0p4
dd if=/tmp/openwrt-*-bananapi_bpi-r3-mini-squashfs-sysupgrade.itb of=/dev/mmcblk0p5
sync
4. Remove the device from power, set boot switch to eMMC and boot into
OpenWrt. The device will come up with IP 192.168.1.1 and assume the
Ethernet port closer to the USB-C power connector as LAN port.
5. If you like to have Ethernet support inside U-Boot (eg. to boot via
TFTP) you also need to write the PHY firmware to /dev/mmcblk0boot1:
echo 0 > /sys/block/mmcblk0boot1/force_ro
dd if=/lib/firmware/airoha/EthMD32.dm.bin of=/dev/mmcblk0boot1
dd if=/lib/firmware/airoha/EthMD32.DSP.bin bs=16384 seek=1 of=/dev/mmcblk0boot1
Installation instructions for NAND
----------------------------------
0. Set boot switch to boot from eMMC (assuming OpenWrt is installed there
by instructions above. Using stock rom or immortalwrt does NOT work!)
1. Write things to NAND
Move files to the device /tmp using scp:
- openwrt-*-bananapi_bpi-r3-mini-snand-preloader.bin
- openwrt-*-bananapi_bpi-r3-mini-snand-bl31-uboot.fip
- openwrt-*-bananapi_bpi-r3-mini-initramfs-recovery.itb
- openwrt-*-bananapi_bpi-r3-mini-squashfs-sysupgrade.itb
Write them to the appropriate locations:
mtd write /tmp/openwrt-*-bananapi_bpi-r3-mini-snand-preloader.bin /dev/mtd0
ubidetach -m 1
ubiformat /dev/mtd1
ubiattach -m 1
volsize=$(wc -c < /tmp/openwrt-*-bananapi_bpi-r3-mini-snand-bl31-uboot.fip)
ubimkvol /dev/ubi0 -N fip -n 0 -s $volsize -t static
ubiupdatevol /dev/ubi0_0 /tmp/openwrt-*-bananapi_bpi-r3-mini-snand-bl31-uboot.fip
cd /lib/firmware/airoha
cat EthMD32.dm.bin EthMD32.DSP.bin > /tmp/en8811h-fw.bin
ubimkvol /dev/ubi0 -N en8811h-firmware -n 1 -s 147456 -t static
ubiupdatevol /dev/ubi0_1 /tmp/en8811h-fw.bin
ubimkvol /dev/ubi0 -n 2 -N ubootenv -s 126976
ubimkvol /dev/ubi0 -n 3 -N ubootenv2 -s 126976
volsize=$(wc -c < /tmp/openwrt-*-bananapi_bpi-r3-mini-initramfs-recovery.itb)
ubimkvol /dev/ubi0 -n 4 -N recovery -s $volsize
ubiupdatevol /dev/ubi0_4 /tmp/openwrt-*-bananapi_bpi-r3-mini-initramfs-recovery.itb
volsize=$(wc -c < /tmp/openwrt-*-bananapi_bpi-r3-mini-squashfs-sysupgrade.itb)
ubimkvol /dev/ubi0 -n 4 -N recovery -s $volsize
ubiupdatevol /dev/ubi0_4 /tmp/openwrt-*-bananapi_bpi-r3-mini-squashfs-sysupgrade.itb
3. Remove the device from power, set boot switch to NAND, power up and
boot into OpenWrt.
Partially based on immortalwrt support for the R3 mini, big thanks for
doing the ground work!
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The Bananapi BPi-R3 is a development router board built around the
MediaTek Filogic 830 (MT7986A) SoC.
The board can boot either from microSD, SPI-NAND, SPI-NOR or eMMC.
Only either SPI-NAND or SPI-NOR can be used at the same time, also only
either microSD or eMMC can be used. The various storage options can be
selected using small SMD switches on the board.
Specs:
* MediaTek MT7986A (Filogic 830) 4x ARM Cortex A53
* 4T4R 2.4G 802.11bgnax (MT7975N)
* 4T4R 5G 802.11anac/ax (MT7975P)
* 2 GB DDR4 RAM
* 8 GB eMMC
* 128 MB SPI-NAND flash
* 32 MB SPI-NOR flash
* on-board MT7531 GbE switch
* 2x SFP+ (1 GbE / 2.5 GbE)
* 5x GbE network port
* miniPCIe slot (only USB 2.0 connected)
* uSIM slot (connected to miniPCIe interface)
* M.2 KEY-E PCIe interface (PCIe x2)
* microSD card interface
* 26 PIN GPIO
Hardware details: https://wiki.banana-pi.org/Banana_Pi_BPI-R3
Working:
* all 4 boot methods incl. installation via U-Boot, sysupgrade, ...
* copper LAN and WAN ports
* SFP1 (connected to gmac1, eth1 in Linux)
* WiFi
* LEDs
* Buttons
* PSTORE/ramoops based dual-boot
Not Working (missing driver features):
* SFP2 (connected to MT7531 switch)
Untested:
* M.2/NGFF slot (PCIe x2)
* mPCIe slot (USB 2.0 + SIM)
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
For devboards without a MAC address assigned from factory, store
the random MAC in U-Boot env on first boot to make it persistent.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
mt76 now spreads the load over multiple CPUs more smoothly, processing
ethernet packets should be faster running on one core
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Since commit 298814e6be ("base-files: config_generate: split macaddr with
multiple ifaces") uci MAC address setup will create a device node for each
member iface. But this script might override the device nodes and interfere
with the MAC address setup.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
The uci config section network.globals set up in /bin/config_generate
will only be created if /proc/sys/net/ipv6 exists.
Correspondingly, lacking IPv6 support, the command
uci set network.globals.packet_steering=1
will fail with "uci: Invalid argument" as the network.globals config
has not been set up.
Fix that by adding the setup there as well.
While at it, limit the uci commit to the network config file.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Leave as enabled by default for mediatek. Also remove obsolete
settings from when packet steering was moved from netifd to a
simplified hotplug script.
Signed-off-by: Alan Swanson <reiver@improbability.net>
This drops support for all the !emmc EVB and adds banannaPi-R2
Also drop mtkhnat until the nftables offoad driver is ready
Signed-off-by: John Crispin <john@phrozen.org>
