We register all gpio buttons and leds through DT, so no need to keep
fixes/additions for the platform data based bay.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46753
Add support for Comtrend VR-3026e v1.
The device is almost identical to the Comtrend VR-3025un.
Signed-off-by: Martin Tesar <tesarmar@gmail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46752
Without this patch adding the wifi device to the bridge may fail
because the bridge is not already configured when the wifi device gets
configured. This patch makes broadcom-wl wait till the bridge is ready.
This fixes#17262
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 46749
Add CONFIG_IEEE80211W variable to DRIVER_MAKEOPTS so that 802.11w
support is properly compiled in full variant.
This fixes#20179
Signed-off-by: Janusz Dziemidowicz <rraptorr@nails.eu.org>
SVN-Revision: 46737
So far support for multiple interface was somehow broken in brcmfmac.
Driver couldn't correctly match firmware and system interfaces resulting
in not working APs and WARNINGs. This pending patches fixes that :)
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 46734
/etc/uci-defaults/02_network had a typo, making it generate the wrong
network config.
Closes#20407.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46727
Add an upstream fix for /proc/net/route causing missing routes doing
several continued reads from it.
Only 4.1+ is affected.
Closes#20403.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46726
should improve flash access times. Should be harmless to gnerally
enable regardless if a flash supporting dual reads is attached. In
doubt, spi-nor will just fall back to serial reads.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46725
We sill don't use kernel 4.2 which is required for backporting using
upstream NVRAM support patch.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 46724
gcc 4.4 was removed in r44957 gcc: remove 4.4.7 (only used by avr32)
gcc 4.5 was removed in r36149
Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de>
SVN-Revision: 46722
A call to pskb_may_pull() might reallocate skb->data. Therefore we
should only assign the src-pointer after any potential reallocations.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 46721
This reverts commit a080e8e1943156168913d0353a2e99d1151102aa.
It did not fix the problem but just hid some symptom. The real issue was
that IGMP/MLD report suppression was not considered for the
multicast-to-unicast feature. A recent netifd which isolates IGMP/MLD
reports between STAs by utilizing AP-isolation and bridge-hairpinning
should have fixed this.
It is perfectly fine to apply multicast-to-unicast to IPv6 Neighbor
Solicitations, too (once that feature is configured correctly).
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 46720
Remove 131-MIPS-export-get_c0_perfcount_int.patch which was already applied
in 4.1.6. This fixes the following build error:
arch/mips/ath79/setup.c:217:77: error: redefinition of '__kstrtab_get_c0_perfcount_int'
arch/mips/ath79/setup.c:211:77: note: previous definition of '__kstrtab_get_c0_perfcount_int' was here
arch/mips/ath79/setup.c:217:350: error: redefinition of '__ksymtab_get_c0_perfcount_int'
arch/mips/ath79/setup.c:211:350: note: previous definition of '__ksymtab_get_c0_perfcount_int' was here
scripts/Makefile.build:258: recipe for target 'arch/mips/ath79/setup.o' failed
Reported-by: swalker
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46715
Properly treat -ENOSYS as no PHY, else ehci-orion won't work without
generic phy support.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46711
The ipw2x00 drivers assume that the system they are running is little
endian, and access everything in native byte order. When run on a big
endian system, everything breaks apart.
Since fixing this is non trivial on a first glance, disable them for
big endian targets.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46708
Some CFEs seem to misconfigure the mapped memory flash access with
fast read but without a dummy byte, causing all accesses to be prefixed
with 0xff.
This of course breaks reading out the nvram, so do not just move back to
single i/o accessors, but also ensure that the dummy byte is correctly
set.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46707
Add a switch to scripts/feeds that allows listing the feeds with their
currently checked out revisions in feeds.conf compatible format.
This allows providing a feeds.conf for public builds to make replication
of the build easier.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46706
Now that the switch driver can handle two devices with
the same MAC address in separate VLANs we can go back
to using the same address on both interfaces.
This is the Linksys firmware's default behavior.
Signed-off-by: Claudio Leite <leitec@staticky.com>
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
SVN-Revision: 46700
This also clears any bootloader-set FDB defaults. This had
caused issues creating port-based VLANs when mappings
overlapped previous VLANs. Packets destined to a port
not in the default port group flooded all ports.
Tested on a 88E6171 (Linksys EA4500) and 88E6172 ('1900AC)
Signed-off-by: Claudio Leite <leitec@staticky.com>
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
SVN-Revision: 46699
