This patch unifies the polled and interrupt-driven gpio_keys code
paths as well implements consistent handling of the debounce
interval set for the GPIO buttons and switches.
Hotplug events will only be fired if
1. The input changes its state and remains stable for the duration
of the debounce interval (default is 5 ms).
2. In the initial stable (no state-change for duration of the
debounce interval) state once the driver module gets loaded.
Switch type inputs will always report their stable state.
Unpressed buttons will not trigger an event for the initial
stable state. Whereas pressed buttons will trigger an event.
This is consistent with upstream's gpio-key driver that uses
the input subsystem (and dont use autorepeat).
Prior to this patch, this was handled inconsistently for interrupt-based
an polled gpio-keys. Hence this patch unifies the shared logic into the
gpio_keys_handle_button() function and modify both implementations to
handle the initial state properly.
The changes described in 2. ) . can have an impact on the
failsafe trigger. Up until now, the script checked for button
state changes. On the down side, this allowed to trigger the
failsafe by releasing a held button at the right time. On the
plus side, the button's polarity setting didn't matter.
Now, the failsafe will only engage when a button was pressed
at the right moment (same as before), but now it can
theoretically also trigger when the button was pressed the
whole time the kernel booted and well into the fast-blinking
preinit phase. However, the chances that this can happen are
really small. This is because the gpio-button module is usually
up and ready even before the preinit state is entered. So, the
initial pressed button event gets lost and most devices behave
as before.
Bisectors: If this patch causes a device to permanently go into
failsafe or experience weird behavior due to inputs, please
check the following:
- the GPIO polarity setting for the button
- the software-debounce value
Run-tested for 'gpio-keys' and 'gpio-keys-polled' on
- devolo WiFi pro 1200e
- devolo WiFi pro 1750c
- devolo WiFi pro 1750x
- Netgear WNDR4700
- Meraki MR24
- RT-AC58U
Signed-off-by: David Bauer <mail@david-bauer.net>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [further
cleanups, simplification and unification]
(cherry picked from commit 27f3f493de0610c74de2ea406641b256bfcc13a9)
While testing 4.19 build on malta/be64, I've encountered following
error:
gpio-button-hotplug/gpio-button-hotplug.c:529:18: error: implicit
declaration of function 'gpio_to_desc'
which is caused by the missing include fixed by this patch.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
(cherry picked from commit dd6d82112a10796dd5aa0f9e9c76ec8e77e7e211)
This addresses an issue where the list option specified in
/etc/config/openvpn i.e. 'tls_cipher' would instead show up in the
generated openvpn-<name>.conf as 'ncp-ciphers'. For context,
'ncp_ciphers' appears after 'tls_cipher' in OPENVPN_LIST from
openvpn.options.
Also, the ordering of the options in the UCI config file is now
preserved when generating the OpenVPN config. The two currently
supported list options deal with cipher preferences.
Signed-off-by: Matt Merhar <mattmerhar@protonmail.com>
(cherry picked from commit 1d4c4cbd20580dd211431ab58460a6eebd5e021e)
* Fix for memory leak regression
* Support for (un)escaping
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit 430d65c544551f9af88cdc6f0b9c6c12364b28f9)
The OpenWrt buildroot ABI version rebuild tracker does not handle
transient dependencies, therefore add all libraries linked by
block-mount and blockd as direct dependencies to the corresponding
binary package definition.
This ensures that block-mount and blockd is automatically rebuilt and
relinked if any of these libraries has its ABI_VERSION updated in the
future.
Fixes: FS#2373
[jow: similar fix for procd and 98.42% of commit message]
Signed-off-by: Jo-Philip Wich <jow@mein.io>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
(cherry picked from commit cbae306815bdfc335eeedc35dc5df3d2d4021a2a)
Now that busybox is a known alternatives provider by opkg, we remove the
ALTERNATIVES spec and add a note to make the implicit situation clear
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
(cherry-picked from commit 62be427067ee3883b68bcfb08dfc0c43dce22fa3)
Opkg starting from this version special-cases busybox as alternatives
provider. There should be no need to add entries to ALTERNATIVES of
busybox package
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
(cherry-picked from commit e51b513f75d28306a744637b0fbe7fdd6e3fb813)
b43legacy needs ssb support and we do not compile the mips74 subtarget
of the brcm47xx target with SSB support. This causes a build failure in
the mac80211 package and only some of the kernel modules are being
created.
I am not aware of any device with a BRCM47xx mips74 CPU which uses a
b43legacy compatible device.
Fixes: FS#2334
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit e05310b9b80f944c718374b449b6fe48d06d412d)
Logic was inverted when changing from string check to file check.
Fix it.
Fixes: 8592602d0a88 ("base-files: Really check path in get_mac_binary")
Reported-by: Matthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit 6ed3349308b24a6bac753643970a1f9f56ff6070)
This includes a fix for a medium-level potential cache attack with a
variant of Bleichenbacher’s attack. Patches were refreshed.
Increased FP_MAX_BITS to allow 4096-bit RSA keys.
Fixed poly1305 build option, and some Makefile updates.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
(cherry picked from commit 2792daab5ad26e916619052fc7f581cddc1ea53c)
Currently, path argument is only checked for being not empty.
This changes behavior to actually check whether path exists.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Restarting service causes file-systems to be unmounted without being
mounted back. When this service was obsoleted it should have been
implemented in a way that all actions are ignored. Up to this commit
default handler was called when restart was requested. This default
handler just simply calls stop and start. That means that stop called
unmount but start just printed that this service is obsoleted.
This instead implements restart that just prints same message like start
does. It just calls start in reality. This makes restart unavailable for
call.
Signed-off-by: Karel Kočí <karel.koci@nic.cz>
(cherry picked from commit 3ead9e7b743b1fbd3b07f5a72a16999abbec9347)
When targets for multiple ESPRESSObin devices were added, not all
files were updated which means any ESPRESSObin version beside generic
won't have proper networking, sysupgrade and uboot-env. This patch
fixes the issue.
* fixup network detection
* fixup uboot-env
* fixup platform.sh for sysupgrade
Signed-off-by: Vladimir Vid <vladimir.vid@sartura.hr>
(cherry picked from commit bc47285cb3c0125424e628521f905f1f0d7b4cef)
Just stumbled across this LEDE legacy, without finding any real reason
to keep it. There is a single LEDE_DEVICE_MANUFACTURER_URL dependency
in the luci feed repo which needs to be syncronized.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
[re-added missing commit message]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
(cherry picked from commit 8a34a54b6aa6e9a5e2983d554fd5b97bec97e891)
Follow upstream changes - header file changes only
no functional or executable changes, hence no package bump
required
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
(cherry picked from commit a8f0c02f80fa0c7c55702770b3ca99f6db5405e7)
This patch adds a missing type property which prevented
the creation of oneshot and timer led triggers when they
are specified in the /etc/board.d/01_leds files.
i.e.:
ucidef_set_led_timer "system" "system" "zhuotk:green:system" "1000" "1000"
Fixes: b06a286a4861 ("base-files: cleanup led functions in uci-defaults.sh")
Signed-off-by: Robinson Wu <wurobinson@qq.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This improves FullMAC firmware compatibility, adds logging in case of
firmware crash and *may* fix "Invalid packet id" errors.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit 8888cb725d492ad5cad5b59fc7117b006e1bba5a)
FCC allows maximum antenna gain of 6 dBi. 15.247(b)(4):
> (4) The conducted output power limit
> specified in paragraph (b) of this section
> is based on the use of antennas
> with directional gains that do not exceed
> 6 dBi. Except as shown in paragraph
> (c) of this section, if transmitting
> antennas of directional gain greater
> than 6 dBi are used, the conducted
> output power from the intentional radiator
> shall be reduced below the stated
> values in paragraphs (b)(1), (b)(2),
> and (b)(3) of this section, as appropriate,
> by the amount in dB that the
> directional gain of the antenna exceeds
> 6 dBi.
https://www.gpo.gov/fdsys/pkg/CFR-2013-title47-vol1/pdf/CFR-2013-title47-vol1-sec15-247.pdf
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Most of the txpower for the ath10k firmware is stored as twicepower (0.5 dB
steps). This isn't the case for max_antenna_gain - which is still expected
by the firmware as dB.
The firmware is converting it from dB to the internal (twicepower)
representation when it calculates the limits of a channel. This can be seen
in tpc_stats when configuring "12" as max_antenna_gain. Instead of the
expected 12 (6 dB), the tpc_stats shows 24 (12 dB).
Tested on QCA9888 and IPQ4019 with firmware 10.4-3.5.3-00057.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
FCC allows maximum antenna gain of 6 dBi. 15.247(b)(4):
> (4) The conducted output power limit
> specified in paragraph (b) of this section
> is based on the use of antennas
> with directional gains that do not exceed
> 6 dBi. Except as shown in paragraph
> (c) of this section, if transmitting
> antennas of directional gain greater
> than 6 dBi are used, the conducted
> output power from the intentional radiator
> shall be reduced below the stated
> values in paragraphs (b)(1), (b)(2),
> and (b)(3) of this section, as appropriate,
> by the amount in dB that the
> directional gain of the antenna exceeds
> 6 dBi.
https://www.gpo.gov/fdsys/pkg/CFR-2013-title47-vol1/pdf/CFR-2013-title47-vol1-sec15-247.pdf
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Most of the txpower for the ath10k firmware is stored as twicepower (0.5 dB
steps). This isn't the case for max_antenna_gain - which is still expected
by the firmware as dB.
The firmware is converting it from dB to the internal (twicepower)
representation when it calculates the limits of a channel. This can be seen
in tpc_stats when configuring "12" as max_antenna_gain. Instead of the
expected 12 (6 dB), the tpc_stats shows 24 (12 dB).
Tested on QCA9888 and IPQ4019 with firmware 10.4-3.5.3-00057.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
FCC allows maximum antenna gain of 6 dBi. 15.247(b)(4):
> (4) The conducted output power limit
> specified in paragraph (b) of this section
> is based on the use of antennas
> with directional gains that do not exceed
> 6 dBi. Except as shown in paragraph
> (c) of this section, if transmitting
> antennas of directional gain greater
> than 6 dBi are used, the conducted
> output power from the intentional radiator
> shall be reduced below the stated
> values in paragraphs (b)(1), (b)(2),
> and (b)(3) of this section, as appropriate,
> by the amount in dB that the
> directional gain of the antenna exceeds
> 6 dBi.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Add support for xfrm interfaces in kernel. XFRM interfaces are used by
the IPsec stack for tunneling.
XFRM interfaces are available since linux 4.19.
Signed-off-by: André Valentin <avalentin@marcant.net>
Commit afc056d7dc83 ("gpio-button-hotplug: support interrupt
properties") changed the gpio-keys interrupt handling logic in a way,
that it always misses first event, which causes issues with rc.button
scripts, so this patch restores the previous behaviour.
Fixes: afc056d7dc83 ("gpio-button-hotplug: support interrupt properties")
Reported-by: Kristian Evensen <kristian.evensen@gmail.com>
Tested-by: Kuan-Yi Li <kyli.tw@gmail.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [drop state check]
Currently the generated event contains wrong seen value, when the button
is pressed for the first time:
rmmod gpio_button_hotplug; modprobe gpio_button_hotplug
[ pressing the wps key immediately after modprobe ]
gpio-keys: create event, name=wps, seen=1088, pressed=1
So this patch adds a check for this corner case and makes seen=0 if the
button is pressed for the first time.
Tested-by: Kuan-Yi Li <kyli.tw@gmail.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This is to make life easier for users with customized build of
dnsmasq-full variant. Currently dnsmasq config generated by current
service script will be rejected by dnsmasq build lacking DHCP feature
- Options like --dhcp-leasefile have default values. Deleting them
from uci config or setting them to empty value will make them take on
default value in the end
- Options like --dhcp-broadcast are output unconditionally
Tackle this by
- Check availablility of features from output of "dnsmasq --version"
- Make a list of options guarded by HAVE_xx macros in src/options.c of
dnsmasq source code
- Ignore these options in xappend()
Two things to note in this implementation
- The option list is not exhaustive. Supposedly only those options that
may cause dnsmasq to reject with "unsupported option (check that
dnsmasq was compiled with DHCP/TFTP/DNSSEC/DBus support)" are taken
into account here
- This provides a way out but users' cooperation is still needed. E.g.
option dnssec needs to be turned off, otherwise the service script
will try to add --conf-file pointing to dnssec specific anchor file
which dnsmasq lacking dnssec support will reject
Resolves FS#2281
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
Busybox brctl applet conflicts with the version from bridge-utils.
Fix this by using ALTERNATIVE support for brctl in busybox.
Signed-off-by: Konstantin Demin <rockdrilla@gmail.com>
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com> [PKG_RELEASE increase]
Add the userspace control portion of the backported kernelspace
act_ctinfo.
ctinfo is a tc action restoring data stored in conntrack marks to
various fields. At present it has two independent modes of operation,
restoration of DSCP into IPv4/v6 diffserv and restoration of conntrack
marks into packet skb marks.
It understands a number of parameters specific to this action in
additional to the usual action syntax. Each operating mode is
independent of the other so all options are optional, however not
specifying at least one mode is a bit pointless.
Usage: ... ctinfo [dscp mask [statemask]] [cpmark [mask]] [zone ZONE]
[CONTROL] [index <INDEX>]
DSCP mode
dscp enables copying of a DSCP stored in the conntrack mark into the
ipv4/v6 diffserv field. The mask is a 32bit field and specifies where
in the conntrack mark the DSCP value is located. It must be 6
contiguous bits long. eg. 0xfc000000 would restore the DSCP from the
upper 6 bits of the conntrack mark.
The DSCP copying may be optionally controlled by a statemask. The
statemask is a 32bit field, usually with a single bit set and must not
overlap the dscp mask. The DSCP restore operation will only take place
if the corresponding bit/s in conntrack mark ANDed with the statemask
yield a non zero result.
eg. dscp 0xfc000000 0x01000000 would retrieve the DSCP from the top 6
bits, whilst using bit 25 as a flag to do so. Bit 26 is unused in this
example.
CPMARK mode
cpmark enables copying of the conntrack mark to the packet skb mark. In
this mode it is completely equivalent to the existing act_connmark
action. Additional functionality is provided by the optional mask
parameter, whereby the stored conntrack mark is logically ANDed with the
cpmark mask before being stored into skb mark. This allows shared usage
of the conntrack mark between applications.
eg. cpmark 0x00ffffff would restore only the lower 24 bits of the
conntrack mark, thus may be useful in the event that the upper 8 bits
are used by the DSCP function.
Usage: ... ctinfo [dscp mask [statemask]] [cpmark [mask]] [zone ZONE]
[CONTROL] [index <INDEX>]
where :
dscp MASK is the bitmask to restore DSCP
STATEMASK is the bitmask to determine conditional restoring
cpmark MASK mask applied to restored packet mark
ZONE is the conntrack zone
CONTROL := reclassify | pipe | drop | continue | ok |
goto chain <CHAIN_INDEX>
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
ctinfo is a new tc filter action module. It is designed to restore
information contained in firewall conntrack marks to other packet fields
and is typically used on packet ingress paths. At present it has two
independent sub-functions or operating modes, DSCP restoration mode &
skb mark restoration mode.
The DSCP restore mode:
This mode copies DSCP values that have been placed in the firewall
conntrack mark back into the IPv4/v6 diffserv fields of relevant
packets.
The DSCP restoration is intended for use and has been found useful for
restoring ingress classifications based on egress classifications across
links that bleach or otherwise change DSCP, typically home ISP Internet
links. Restoring DSCP on ingress on the WAN link allows qdiscs such as
but by no means limited to CAKE to shape inbound packets according to
policies that are easier to set & mark on egress.
Ingress classification is traditionally a challenging task since
iptables rules haven't yet run and tc filter/eBPF programs are pre-NAT
lookups, hence are unable to see internal IPv4 addresses as used on the
typical home masquerading gateway. Thus marking the connection in some
manner on egress for later restoration of classification on ingress is
easier to implement.
Parameters related to DSCP restore mode:
dscpmask - a 32 bit mask of 6 contiguous bits and indicate bits of the
conntrack mark field contain the DSCP value to be restored.
statemask - a 32 bit mask of (usually) 1 bit length, outside the area
specified by dscpmask. This represents a conditional operation flag
whereby the DSCP is only restored if the flag is set. This is useful to
implement a 'one shot' iptables based classification where the
'complicated' iptables rules are only run once to classify the
connection on initial (egress) packet and subsequent packets are all
marked/restored with the same DSCP. A mask of zero disables the
conditional behaviour ie. the conntrack mark DSCP bits are always
restored to the ip diffserv field (assuming the conntrack entry is found
& the skb is an ipv4/ipv6 type)
e.g. dscpmask 0xfc000000 statemask 0x01000000
|----0xFC----conntrack mark----000000---|
| Bits 31-26 | bit 25 | bit24 |~~~ Bit 0|
| DSCP | unused | flag |unused |
|-----------------------0x01---000000---|
| |
| |
---| Conditional flag
v only restore if set
|-ip diffserv-|
| 6 bits |
|-------------|
The skb mark restore mode (cpmark):
This mode copies the firewall conntrack mark to the skb's mark field.
It is completely the functional equivalent of the existing act_connmark
action with the additional feature of being able to apply a mask to the
restored value.
Parameters related to skb mark restore mode:
mask - a 32 bit mask applied to the firewall conntrack mark to mask out
bits unwanted for restoration. This can be useful where the conntrack
mark is being used for different purposes by different applications. If
not specified and by default the whole mark field is copied (i.e.
default mask of 0xffffffff)
e.g. mask 0x00ffffff to mask out the top 8 bits being used by the
aforementioned DSCP restore mode.
|----0x00----conntrack mark----ffffff---|
| Bits 31-24 | |
| DSCP & flag| some value here |
|---------------------------------------|
|
|
v
|------------skb mark-------------------|
| | |
| zeroed | |
|---------------------------------------|
Overall parameters:
zone - conntrack zone
control - action related control (reclassify | pipe | drop | continue |
ok | goto chain <CHAIN_INDEX>)
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Reviewed-by: Toke Høiland-Jørgensen <toke@redhat.com>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make suitable adjustments for backporting to 4.14 & 4.19
and add to SCHED_MODULES_FILTER
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Current latest LSDK-19.03 u-boot had a bug that bootcmd
environment was always been reset when u-boot started up.
This was found on boards with spi NOR boot. Before the
proper fix-up is applied, we have to use a workaround
to hard code the bootcmd for OpenWrt booting for now.
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
This patch is to convert to use TF-A for firmware.
- Use un-swapped rcw since swapping will be done in TF-A.
- Use u-boot with TF-A defconfig.
- Rework memory map for TF-A introduction.
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Add TF-A packages for Layerscape to implement trusted firmware.
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
