Added patch for GCC to fix compilation issues on MacOS arm64
The original commit message from Przemysław Buczkowski:
GCC: Patch for Apple Silicon compatibility
This patch fixes a linker error occuring when compiling
the cross-compiler on macOS and ARM64 architecture.
Adapted from:
https://github.com/richfelker/musl-cross-make/issues/116#issuecomment-823612404
Signed-off-by: Sergey V. Lobanov <sergey@lobanov.in>
Added patch for MacOS without 32 bit inodes support
(__DARWIN_ONLY_64_BIT_INO_T is true)
This patch based on discussion https://github.com/archmac/bootstrap/issues/4
Signed-off-by: Sergey V. Lobanov <sergey@lobanov.in>
a6451fea5a3d mt76: mt7615: improve wmm index allocation
1911486414dc mt76: mt7915: improve wmm index allocation
7998a41d1321 mt76: clear sta powersave flag after notifying driver
664475574438 mt76: mt7603: introduce SAR support
5c0da39c940b mt76: mt7915: introduce SAR support
77fc6c439a32 mt76: mt7603: improve reliability of tx powersave filtering
094b3d800835 firmware: update mt7663 rebb firmware to 20200904171623
25237b19bcc1 mt76: eeprom: tolerate corrected bit-flips
1463cb4c6ac2 mt76: mt7921: fix boolreturn.cocci warning
586bad6020f7 mt76: mt7921: use correct iftype data on 6GHz cap init
8ec95c910425 mt76: mt7921s: fix bus hang with wrong privilege
688e30c7d854 firmware: update mt7921 firmware to version 20211014
6fad970893dd mt76: fix key pointer overwrite in mt7921s_write_txwi/mt7663_usb_sdio_write_txwi
95acf972750c mt76: fix 802.3 RX fail by hdr_trans
3f402b0cf6c0 mt76: mt7921s: fix possible kernel crash due to invalid Rx count
929a03a8d65d mt76: connac: fix last_chan configuration in mt76_connac_mcu_rate_txpower_band
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Update wifi firmware used for nanopi neo air, with
cypress-firmware-43430-sdio there is no wifi detected, as
brcmfmac-firmware-43430a0-sdio allow to acces to wifi.
Signed-off-by: Michel Promonet <michel.promonet@free.fr>
This results in setting format specific data (format info, extract
commands) in a single function. It should help maintaining sysupgrade
code.
This change has been tested on Asus GT-AC5300 and Netgear R8000P.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
List of supported formats grew over time and implementation got a bit
messy. There are multiple functions with format-specific parameters and
commands.
Refactor it by making platform_identify() setup all required info right
after detecting firmware format. This simplifies formats handling in
platform_other_check_image() and platform_do_upgrade() a lot.
This has been tested on:
1. SmartRG SR400ac (TRX): non-NAND sysupgrade
2. Netgear R8000 (CHK): NAND aware and standard sysupgrade-s
3. D-Link DIR-885L (Seama): NAND aware and standard sysupgrade-s
4. Luxul XWR-3150 (LXL): NAND aware and standard sysupgrade-s
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This patch is a revert of the upstream patch to Debian's ca-certificate
commit 033d52259172 ("mozilla/certdata2pem.py: print a warning for expired certificates.")
The reason is, that this change broke builds with the popular
Ubuntu 20.04 LTS (focal) releases which are shipping with an
older version of the python3-cryptography package that is not
compatible.
|Traceback (most recent call last):
| File "certdata2pem.py", line 125, in <module>
| cert = x509.load_der_x509_certificate(obj['CKA_VALUE'])
|TypeError: load_der_x509_certificate() missing 1 required positional argument: 'backend'
|make[5]: *** [Makefile:6: all] Error 1
...or if the python3-cryptography was missing all together:
|Traceback (most recent call last):
| File "/certdata2pem.py", line 31, in <module>
| from cryptography import x509
|ModuleNotFoundError: No module named 'cryptography'
More concerns were raised by Jo-Philipp Wich:
"We don't want the build to depend on the local system time anyway.
Right now it seems to be just a warning but I could imagine that
eventually certs are simply omitted of found to be expired at
build time which would break reproducibility."
Link: <https://github.com/openwrt/openwrt/commit/7c99085bd697>
Reported-by: Chen Minqiang <ptpt52@gmail.com>
Reported-by: Shane Synan <digitalcircuit36939@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The xway_legacy subtarget only supports 5 devices. Most compiled
switch drivers are unused by any of these devices. The same drivers
are compiled into the xway subtarget. They were probably copied
from there when creating this subtarget.
Switches used by devices:
Arcadyan ARV4518PWR01 Realtek RTL8306SD
Arcadyan ARV4518PWR01A Realtek RTL8306SD
Arcadyan ARV4520PW Infineon ADM6996I
Arcadyan ARV4525PW only PHY(IC+ IP101A)
Arcadyan ARV452CQW Realtek RTL8306
The CONFIG_ETHERNET_PACKET_MANGLE symbol has also been disabled,
as it is only needed by the driver for AR8216.
Reduces kernel size by 19.9 kB.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
We actually need to enclose the whole section of partitions in a
`partitions { ... }` to assign it a `compatible = "fixed-partitions";
otherwise the partition referred to by `hwinfo` won't be registered
when bringing up MTD partitions, for example as per:
- <https://forum.openwrt.org/t/tp-link-c2600-missing-default-mac-mtd-partition-in-snapshot/103945/6>
- commit e2b03c16eb ("ipq806x: add missing enclosing partitions block for TP-Link C2600")'
Fixes: 8ec21d6bb2 ("mpc85xx: convert mtd-mac-address to nvmem implementation")
Signed-off-by: Martin Kennedy <hurricos@gmail.com>
[minor beautification]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This target does not activate CONFIG_PCI kernel configuration option, do
not activate the PCI feature. This will deactivate some PCI drivers
which are not building without PCI support in the kernel.
If PCI_SUPPORT or PCIE_SUPPORT are activated in the kernel configuration
the feature flag will be automatically set by the build system again.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Deactivate all the symbols of the B53 DSA driver in the generic kernel
configuration. Multiple targets are now using this drivers and they
only need some of the options.
This fixes the bcm4908 build which didn't deactivate all of the options.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
From driver source:
{ .compatible = "allwinner,sun4i-a10-rtc", .data =
&data_year_param[0] },
{ .compatible = "allwinner,sun7i-a20-rtc", .data =
&data_year_param[1] },
The rtc-sunxi module only supports allwinner a10 and a20 SoCs,
other SoCs in the cortexa7 and cortexa53 subtarget using the
CONFIG_RTC_DRV_SUN6I driver which is compiled into the kernel
binary, so remove this package for these unsupported devices.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
When compiling with CONFIG_USE_RFKILL=y, the build fails and mentions that
dependency on kmod-rfkill is missing, which is correct [1]. Add this
dependency to the Makefile.
Depend on +USE_RFKILL and not PACKAGE_kmod-rfkill, because it forces
selection of kmod-rfkill package. Other combinations in DEPENDS like
USE_RFKILL:kmod-rfkill or (+)PACKAGE_kmod-rfkill:kmod-rfkill do not force
selection of kmod-rfkill package.
The kmod-rfkill package itself depends on USE_RFKILL, so with +USE_RFKILL
in kmod-cfg80211 package it is not possible to select wrong combination of
packages.
[1] https://linux-wireless.vger.kernel.narkive.com/m8JY9Iks/cfg80211-depends-on-rfkill-or-not
Signed-off-by: Oldřich Jedlička <oldium.pro@gmail.com>
If spectral scan support is enabled then ath10k-ct will cause a NULL
pointer due to relay_open() being called with a const callback struct
which is only supported in kernel 5.11 and later.
So, simply check the kernel version and if 5.11 and newer use the const
callback struct, otherwise use the regular struct.
Fixes: 553a3ac ("ath10k-ct: use 5.15 version")
Signed-off-by: Robert Marko <robimarko@gmail.com>
The Netgear GS110TPP v1 switch cannot reliably perform cold reboots
using the system's internal reset controller.
On this device, and the other supported Netgear switches, internal GPIO
line 13 is connected to the system's hard reset logic. Expose this GPIO
on all systems to ensure restarts work properly.
Cc: Raylynn Knight <rayknight@me.com>
Cc: Michael Mohr <akihana@gmail.com>
Cc: Stijn Segers <foss@volatilesystems.org>
Cc: Stijn Tintel <stijn@linux-ipv6.be>
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Tested-by: Bjørn Mork <bjorn@mork.no>
Add the gpio-restart driver to the realtek build. This way devices,
which cannot reliably perform resets using the SoC's internal reset
logic, can use a GPIO line to drive the SoC's hard reset input.
Signed-off-by: Sander Vanheule <sander@svanheule.net>
The internal GPIO controller on RTL838x is also an IRQ controller, which
requires the 'interrupt-controller' and '#interrupts-cells' properties
to be present in the device tree.
Reported-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Some devices are assigned globally unique MAC addresses for all
ports. These are stored by U-Boot in the second U-Boot enviroment
("sysinfo") as a range of start and end address.
Use the full range if provided.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
The default management interface should be easy to find for users
doing "blind" installations without console access. There are
already multiple examples in the forum of advanced early adopters
having problems locating the management interface after installing
OpenWrt.
Requiring tagged VLAN configration to access the initial management
interface creates unnecessary hassle at best. Errors on the other
end are close to impossible to debug without console access, even
for advanced users. Less advanced users might have problems with
the concept of VLAN tagging.
Limiting management access to a single arbitrary port among up to
52 possible LAN ports makes this even more difficult, for no
reason at all. Users might have reasons to use a different port
for management. And they might even have difficulties using the
OpenWrt selected one. The port might be the wrong type for their
management link (e.g copper instead of fibre). Or they might
depend on PoE power from a device which they can't reconfigure.
User expectations will be based on
- OpenWrt defaults for other devices
- stock firmware default for the device in question
- common default behaviour of similar devices
All 3 cases point to a static IP address accessible on the native
VLAN of any LAN port. A switch does not have any WAN port. All
ports are LAN ports.
This changes the default network configuration in line with these
expectations.
Cc: John Crispin <john@phrozen.org>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
The configs/omap3_overo_defconfig file was removed from upstream U-Boot
in commit ed3294d6d1f9 ("arm: Remove overo board"). Remove it in OpenWrt
too. If someone needs this please add it also to upstream U-Boot.
This fixes the compile of the omap target.
Fixes: ffb807ec90 ("omap: update u-boot to 2021.07")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
CONFIG_EXTERNAL_CPIO is a string variable, hence testing for 'y'
doesn't make much sense here.
Fixes: 330bd380e8 ("image: allow building FIT and uImage with ramdisk")
Reported-by: Huangbin Zhan <zhanhb88@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This patch adds support for the Teltonika RUTX10.
This device is an industrial DIN-rail router with 4 ethernet ports,
2.4G/5G dualband WiFi, Bluetooth, a USB 2.0 port and two GPIOs.
The RUTX series devices are very similiar so common parts of the DTS
are kept in a DTSI file. They are based on the QCA AP-DK01.1-C1 dev
board.
See https://teltonika-networks.com/product/rutx10 for more info.
Hardware:
SoC: Qualcomm IPQ4018
RAM: 256MB DDR3
SPI Flash 1: XTX XT25F128B (16MB, NOR)
SPI Flash 2: XTX XT26G02AWS (256MB, NAND)
Ethernet: Built-in IPQ4018 (SoC, QCA8075), 4x 10/100/1000 ports
WiFi 1: Qualcomm QCA4019 IEEE 802.11b/g/n
Wifi 2: Qualcomm QCA4019 IEEE 802.11a/n/ac
USB Hub: Genesys Logic GL852GT
Bluetooth: Qualcomm CSR8510 (A10U)
LED/GPIO controller: STM32F030 with custom firmware
Buttons: Reset button
Leds: Power (green, cannot be controlled)
WiFi 2.4G activity (green)
WiFi 5G activity (green)
MACs Details verified with the stock firmware:
eth0: Partition 0:CONFIG Offset: 0x0
eth1: = eth0 + 1
radio0 (2.4 GHz): = eth0 + 2
radio1 (5.0 GHz): = eth0 + 3
Label MAC address is from eth0.
The LED/GPIO controller needs a separate kernel driver to function.
The driver was extracted from the Teltonika GPL sources and can be
found at following feed: https://github.com/0xFelix/teltonika-rutx-openwrt
USB detection of the bluetooth interface is sometimes a bit flaky. When
not detected power cycle the device. When the bluetooth interface was
detected properly it can be used with bluez / bluetoothctl.
Flash instructions via stock web interface (sysupgrade based):
1. Set PC to fixed ip address 192.168.1.100
2. Push reset button and power on the device
3. Open u-boot HTTP recovery at http://192.168.1.1
4. Upload latest stock firmware and wait until the device is rebooted
5. Open stock web interface at http://192.168.1.1
6. Set some password so the web interface is happy
7. Go to firmware upgrade settings
8. Choose
openwrt-ipq40xx-generic-teltonika_rutx10-squashfs-nand-factory.ubi
9. Set 'Keep settings' to off
10. Click update, when warned that it is not a signed image proceed
Return to stock firmware:
1. Set PC to fixed ip address 192.168.1.100
2. Push reset button and power on the device
3. Open u-boot HTTP recovery at http://192.168.1.1
4. Upload latest stock firmware and wait until the device is rebooted
Note: The DTS expects OpenWrt to be running from the second rootfs
partition. u-boot on these devices hot-patches the DTS so running from the
first rootfs partition should also be possible. If you want to be save follow
the instructions above. u-boot HTTP recovery restores the device so that when
flashing OpenWrt from stock firmware it is flashed to the second rootfs
partition and the DTS matches.
Signed-off-by: Felix Matouschek <felix@matouschek.org>
The MR42 and MR52 are two similar IPQ806x based devices from the Cisco
Meraki "Cryptid" series.
MR42 main features:
- IPQ8068 1.4GHz
- 512MB RAM
- 128MB NAND
- 2x QCA9992 (2.4 & 5GHz)
- 1x QCA9889 (2.4 & 5GHz)
- 1x AR8033 PHY
- PoE/AC power
MR52 main features:
- IPQ8068 1.4GHz
- 512MB RAM
- 128MB NAND
- 2x QCA9994 (2.4 & 5GHz)
- 1x QCA9889 (2.4 & 5GHz)
- 2x AR8033 PHYs
- PoE/AC power
(MR42 Only) Installation via diagnostic mode:
If you can successfully complete step 1 then you can continue to install
via this method without having to open the device. Otherwise please use
the standard UART method. Please note that when booting via TFTP, some
Ethernet devices, in particular those on laptops, will not connect in
time, resulting in TFTP boot not succeeding. In this instance it is
advised to connect via a switch.
1. Hold down reset at power on and keep holding, after around 10 seconds
if the orange LED changes behaviour to begin flashing, proceed to
release reset, then press reset two times. Ensure that the LED has
turned blue. Note that flashing will occur on some devices, but it
will not be possible to change the LED colour using the reset button.
In this case it will still be possible to continue with this install
method.
2. Set your IP to 192.168.1.250. Set up a TFTP server serving
mr42_u-boot.mbn and
openwrt-ipq806x-generic-meraki_mr42-initramfs-fit-uImage.itb, obtained
from [1].
3. Use telnet and connect to 192.168.1.1. Run the following commands to
install u-boot. Note that all these commands are critical, an error
will likely render the device unusable.
Option 3.1:
If you are sure you have set up the TFTP server correctly you can
run this script on the device. This will download and flash the
u-boot image immediately:
`/etc/update_uboot.sh 192.168.1.250 mr42_u-boot.mbn`
Once completed successfully, power off the device.
Option 3.2:
If you are unsure the TFTP server is correctly set up you can
obtain the image and flash manually:
3.2.1. `cd /tmp`
3.2.2. `tftp-hpa 192.168.1.250 -m binary -c get mr42_u-boot.mbn`
3.2.3. Confirm file has downloaded correctly by comparing the
md5sum:
`md5sum mr42_u-boot.mbn`
3.2.4. The following are the required commands to write the image.
`echo 1 > /sys/devices/platform/msm_nand/boot_layout
mtd erase /dev/mtd1
nandwrite -pam /dev/mtd1 mr42_u-boot.mbn
echo 0 > /sys/devices/platform/msm_nand/boot_layout`
Important: You must observe the output of the `nandwrite`
command. Look for the following to verify writing is occurring:
`Writing data to block 0 at offset 0x0
Writing data to block 1 at offset 0x20000
Writing data to block 2 at offset 0x40000`
If you do not see this then do not power off the device. Check
your previous commands and that mr42_u-boot.mbn was downloaded
correctly. Once you are sure the image has been written you
can proceed to power off the device.
4. Hold the reset button and power on the device. This will immediately
begin downloading the appropriate initramfs image and boot into it.
Note: If the device does not download the initramfs, this is likely
due to the interface not being brought up in time. Changing Ethernet
source to a router or switch will likely resolve this. You can also
try manually setting the link speed to 10Mb/s Half-Duplex.
5. Once a solid white LED is displayed on the device, continue to the
UART installation method, step 6.
Standard installation via UART - MR42 & MR52
1. Disassemble the device and connect a UART header. The header pinout
is as follows:
1 - 3.3v
2 - TXD
3 - RXD
4 - GND
Important: You should only connect TXD, RXD and GND. Connecting
3.3v may damage the device.
2. Set your IP to 192.168.1.250. Set up a TFTP server serving
openwrt-ipq806x-generic-meraki_(mr42|mr52)-initramfs-fit-uImage.itb.
Separately obtain the respective sysupgrade image.
3. Run the following commands, preferably from a Linux host. The
mentioned files, including ubootwrite.py and u-boot images, can be
obtained from [1].
`python ubootwrite.py --write=(mr42|mr52)_u-boot.bin`
The default for "--serial" option is /dev/ttyUSB0.
4. Power on the device. The ubootwrite script will upload the image to
the device and launch it. The second stage u-boot will in turn load
the initramfs image by TFTP, provided the TFTP server is running
correctly. This process will take about 13 minutes. Once a solid
white LED is displayed, the image has successfully finished
loading. Note: If the image does not load via TFTP, try again with
the Ethernet link to 10Mb/s Half-Duplex.
5. (MR42 only) Do not connect over the network. Instead connect over
the UART using minicom or similar tool. To replace u-boot with
the network enabled version, please run the following commands.
Note that in the provided initramfs images, the u-boot.mbn file
is located in /root:
If you have not used the provided initramfs, you must ensure you
are using an image with "boot_layout" ECC configuration enabled in
the Kernel. This will be version 5.10 or higher. If you do not do
this correctly the device will be bricked.
`insmod mtd-rw i_want_a_brick=1
mtd erase /dev/mtd8
nandwrite -pam /dev/mtd8 /root/mr42_u-boot.mbn`
After running nandwrite, ensure you observe the following output:
`Writing data to block 0 at offset 0x0
Writing data to block 1 at offset 0x20000
Writing data to block 2 at offset 0x40000`
6. (Optional) If you have no further use for the Meraki OS, you can
remove all other UBI volumes on ubi0 (mtd11), including diagnostic1,
part.old, storage and part.safe. You must not remove the ubi1 ART
partition (mtd12).
`for i in diagnostic1 part.old storage part.safe ; do
ubirmvol /dev/ubi0 -N $i
done`
7. Proceed to flash the sysupgrade image via luci, or else download or
scp the image to /tmp and use the sysupgrade command.
[1] The mentioned images and ubootwrite.py script can be found in this repo:
https://github.com/clayface/openwrt-cryptid
[2] The modified u-boot sources for the MR42 and MR52 are available:
https://github.com/clayface/U-boot-MR52-20200629
Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
Add backports of the following patches:
"net: stmmac: explicitly deassert GMAC_AHB_RESET" and
"ARM: dts: qcom: add ahb reset to ipq806x-gmac"
Required for Meraki MR42/MR52.
Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
Rather than having separate patches for each GSBI node added, this patch
consolidates the existing GSBI1 patch into
083-ipq8064-dtsi-additions.patch. In addition, GSBI6 and GSBI7 I2C nodes,
required for the MR42 and MR52 respectively, are added.
Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
Add back support for the TLC591xx series LEDs which are used in the
ipq806x-based Meraki Cryptid series devices.
This module previously existed for the mvebu platform but was removed
at commit f849c2c832 due to being enabled
in that platform's kernel config.
Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
This adds support for the MikroTik RouterBOARD RBD53iG-5HacD2HnD
(hAP ac³), a indoor dual band, dual-radio 802.11ac
wireless AP with external omnidirectional antennae, USB port, five
10/100/1000 Mbps Ethernet ports and PoE passthrough.
See https://mikrotik.com/product/hap_ac3 for more info.
Specifications:
- SoC: Qualcomm Atheros IPQ4019
- RAM: 256 MB
- Storage: 16 MB NOR + 128 MB NAND
- Wireless:
· Built-in IPQ4019 (SoC) 802.11b/g/n 2x2:2, 3 dBi antennae
· Built-in IPQ4019 (SoC) 802.11a/n/ac 2x2:2, 5.5 dBi antennae
- Ethernet: Built-in IPQ4019 (SoC, QCA8075) , 5x 1000/100/10 port,
passive PoE in, PoE passtrough on port 5
- 1x USB Type A port
Installation:
1. Boot the initramfs image via TFTP
2. Run "cat /proc/mtd" and look for "ubi" partition mtd device number, ex. "mtd1"
3. Use ubiformat to remove MikroTik specific UBI volumes
* Detach the UBI partition by running: "ubidetach -d 0"
* Format the partition by running: "ubiformat /dev/mtdN -y"
Replace mtdN with the correct mtd index from step 2.
3. Flash the sysupgrade image using "sysupgrade -n"
Signed-off-by: Robert Marko <robimarko@gmail.com>
Tested-by: Mark Birss <markbirss@gmail.com>
Tested-by: Michael Büchler <michael.buechler@posteo.net>
Tested-by: Alex Tomkins <tomkins@darkzone.net>
Currently nand_upgrade_tar() will pass the kernel length
to nand_upgrade_prepare_ubi() in all cases except for when
the kernel is to be installed in a separate partition as a
binary with the MTD tool.
While this is fine for almost all cases newer MikroTik NAND
devices like hAP ac3 require the kernel to be installed as a
UBIFS packed UBI volume in its own partition.
So, since we have a custom recipe to use ubiformat to flash
the kernel in its partition it makes no sense for sysupgrade
to also install the kernel as a UBI volume in the "ubi"
partition as it only wastes space and will never be used.
So, simply check whether CI_KERNPART is set to "none" and
if so unset the "has_kernel" variable which will in turn
prevent the kernel length from being passed on and then
the kernel UBI volume wont be created for no usefull purpose.
The ath79 MikroTik NAND target has been setting CI_KERNPART
to "none" for a while now altough that was not preventing
the kernel to be installed as UBI volume as well.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Newer NAND devices from MikroTik like the hAP ac3
require the kernel to be packed into UBIFS and then
ubinized.
So, since the ubinize-image.sh script can now ubinize
kernel only as well lets add a command for it.
This now allows calling ubinize-kernel in the kernel
packaging at then end.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Rootfs is now optional in ubinize-image.sh and
requires --rootfs flag instead of just passing the
rootfs image as the argument before ubinize opts.
So, simply add --rootfs flag before the $(IMAGE_ROOTFS).
Signed-off-by: Robert Marko <robimarko@gmail.com>
Currently ubinize-image script always expects the
rootfs image to be passed and a volume for it created.
So, to allow only ubinizing a kernel for example which
the MikroTik hAP ac3 and other new NAND devices from
MikroTik require make rootfs an optional parameter like
kernel.
Signed-off-by: Robert Marko <robimarko@gmail.com>
All patches automatically rebased.
Build system: x86_64
Build-tested: ramips/mt7621*
*I am hit with the binutils 2.37 bug so I had to revert 7f1edbd412
in order to downgrade to 2.35.1
Signed-off-by: John Audia <graysky@archlinux.us>
Update ath10k-ct to get the upstream fix for
DFS support for VHT160 in the 5.15 based ath10k-ct.
(Switch from 5.10 to 5.15 surfaced the upstream regression.)
* refresh one patch
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
Steven Maddox reported in the OpenWrt bugzilla, that his
RaidSonic IB-NAS4220-B was no longer booting with the new
OpenWrt 21.02 (uses linux 5.10's device-tree). However, it was
working with the previous OpenWrt 19.07 series (uses 4.14).
(This is still under investigation.)
Bugzilla: https://bugs.openwrt.org/index.php?do=details&task_id=4137
Reported-by: Steven Maddox <s.maddox@lantizia.me.uk>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
the Netgear EX6100v2 and EX6150v2 can utilize the nvmem
for the pre-calibration and mac-address for both WIFI
devices.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
