ALFA Network R36M-E4G is a dual-SIM, N300 Wi-Fi, compact size platform
based on MediaTek MT7620A WiSoC. This product is designed for operation
with 4G modem (can be bought in bundle with Quectel EC25, EG25 or EP06)
but supports also Wi-Fi modules (miniPCIe slot has USB and PCIe buses).
Specification:
- MT7620A (580 MHz)
- 64/128/256 MB of RAM (DDR2)
- 16/32+ MB of FLASH (SPI NOR)
- 2x 10/100 Mbps Ethernet, with passive PoE support (24 V)
- 2T2R 2.4 GHz (MT7620A), with ext. LNA (RFFM4227)
- 1x miniPCIe slot (with PCIe and USB 2.0 buses and optional 5 V)
- 2x SIM slot (mini, micro) with detect and switch driven by GPIO
- 2x u.fl antenna connectors (for Wi-Fi)
- 8x LED (7 driven by GPIO)
- 2x button (reset, wifi)
- 2x UART (4-pin/2.54 mm pitch, 10-pin/1.27 mm pitch) headers on PCB
- 1x I2C (4-pin, 1.27 mm pitch) header on PCB
- 1x LED (8-pin, 1.27 mm pitch) header on PCB
- 1x DC jack with lock (12 V)
Other:
- there is a dedicated, 4-pin connector for optional RTC module (Holtek
HT138x) with 'enable' input, not available at the time of preparing
support for this board
- miniPCIe slot supports additional 5 V supply on pins 47 and 49 but a
jumper resistor (R174) is not installed by default
- U-Boot selects default SIM slot, based on value of 'default_sim' env
variable: '1' or unset -> SIM1 (mini), '2' -> SIM2 (micro). This will
work only if both slots are occupied, otherwise U-Boot will always
select slot with SIM card inside (user can override it later, in
user-space)
- U-Boot resets the modem, using PERSTn signal, before starting kernel
- this board supports 'dual image' feature (controlled by 'dual_image'
U-Boot environment variable)
Flash instruction:
You can use the 'sysupgrade' image directly in vendor firmware which is
based on OpenWrt (make sure to not preserve settings - use 'sysupgrade
-n -F ...' command). Alternatively, use web recovery mode in U-Boot:
1. Power the device with reset button pressed, the modem LED will start
blinking slowly and after ~3 seconds, when it starts blinking faster,
you can release the button.
2. Setup static IP 192.168.1.2/24 on your PC.
3. Go to 192.168.1.1 in browser and upload 'sysupgrade' image.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
New U-Boot version for MediaTek MT76x8/MT762x based ALFA Network boards
includes support for a 'dual image' feature. Users can enable it using
U-Boot environment variable 'dual_image' ('1' -> enabled).
When 'dual image' feature is enabled, U-Boot will modify DTB and divide
the original 'firmware' flash area into two, equal in size and aligned
to 64 KB partitions: 'firmware' and 'backup'. U-Boot will also adjust
size of 'firmware' area to match installed flash chip size.
U-Boot will load kernel from active partition which is marked with env
variable 'bootactive' ('1' -> first partition, '2' -> second partition)
and rename both partitions accordingly ('firmware' <-> 'backup').
There are 3 additional env variables used to control 'dual image' mode:
- bootlimit - maximum number of unsuccessful boot tries (default: '3')
- bootcount - current number of boot tries
- bootchanged - flag which informs that active partition was changed; if
it is set and 'bootcount' reaches 'bootlimit' value,
U-Boot will start web-based recovery which then updates
both partitions with provided image
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Discovered recent changes had broken sysupgrade for ar71xx mikrotik
rb-493g, traced the problem to missing /usr/share/libubox/jshn.sh after
switching to tmpfs.
Signed-off-by: Russell Senior <russell@personaltelco.net>
CY-SWR1100 has a USB LED but kmod-usb-ledtrig-usbport is missing
in default images. This commit adds it.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
[changed commit title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This patch does the following:
- rename "devdata" flash partition and make it read-only
- switch from gpio-keys-polled to gpio-keys
- add missing power LED
- set correct PCI ID to compatible string in wifi node
- remove ralink,5ghz property in wifi node
- provide label MAC address
Rename devdata partition to devconf as indicated in the stock firmware
partition table:
00030000-00040000: "devdata"
00040000-00050000: "devconf"
Power LED can be controlled by SoC GPIO. Add it in the dts leds node.
RT3092L supports only bgn mode, so it is unnecessary to disable 5GHz band.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Ethernet MAC address setup has been broken since c3e420f28c. Restore
original setting.
Fixes: c3e420f28c ("ramips: Add support for D-Link DCH-M225")
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
As discussed in 1d18a14a90 ("ath79: really fix TP-Link Archer C7
v2 MAC address"), stock firmware MAC address assignment is
actually as follows:
wlan0 (5GHz) : -1
wlan1 (2.4GHz) : 0
eth1 (LAN) : 0
eth0 (WAN) : 1
This has never been fixed for ar71xx, so let's do it now.
Note that with WDR4900 v2 even both wlan0 and wlan1 where assigned
to basemac-1 before ...
Fixes: FS#408
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This replaces all uses of $(cat /sys/class/ieee80211/phyX/macaddress)
by retrieval from the proper flash locations. This will make
02_network independent of WiFi setup again.
For future reference:
The MAC addresses of the FRITZ!WLAN Repeater 300E can be extracted
from the urlader key value store:
maca *:6B
macb *:6C
macwlan *:6D
macdsl *:6E
and be set by e.g.
addr=$(fritz_tffs -n maca -i $(find_mtd_part "tffs (1)"))
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This replaces all uses of $(cat /sys/class/ieee80211/phyX/macaddress)
by retrieval from the proper flash locations. This will make
02_network independent of WiFi setup again.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
uci-defaults are sourced and non-executable, so they do not require
a shebang.
While at it, apply consistent naming scheme.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Replace 2 instances of non posix use of 'head' with posix compliant
'cut'.
'head -c n' cuts 'n' bytes from the passed string and happens to work on
Linux & Mac OS X even though '-c' is not posix.
'head --bytes n' does the same thing and happens to work on linux but
not on Mac OS X and is also not posix.
'cut -b1-8' cuts the first 8 bytes from the passed string and is posix
compliant, hence works on Linux & Mac OS X.
Our usage of 'head --bytes' was particularly unfortunate since it was
used to calculated the RootFS UUID passed to grub - the net result being
a non-functioning system waiting for the root file system to appear.
Thanks to karlp, ynezz & others for pointers on solving this.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Now that netifd and hostapd allow dynamic reconfiguration, add a
command to trigger it.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Change scripts to use ubus interface of hostapd/wpa_supplicant to
add/remove/modify wireless interfaces instead of (re-)starting the
services.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add ubus interface to hostapd and wpa_supplicant to allow dynamically
reloading wiface configuration without having to restart the hostapd
process.
As a consequence, both hostapd and wpa_supplicant are now started
persistently on boot for each wifi device in the system and then
receive ubus calls adding, modifying or removing interface
configuration.
At a later stage it would be desirable to reduce the services to one
single instance managing all radios.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
7a723d0 wireless: add ubus method for reloading configuration
e15147c wireless: make reconf opt-in and allow serializing configuration
Set new option 'reconf' in 'wifi-device' section to enable dynamic
re-configuration on that radio.
If necessary, also set option 'serialize' which forced netifd to
configure interfaces of wireless devices one-by-one.
Both options are disabled by default.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
In ar71xx, the board name for the TL-WR1043ND v3 is equal to v2:
tl-wr1043nd-v2
Fix SUPPORTED_DEVICES for v3 in ath79 accordingly.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The led wireless trigger is already set correctly to phy0tpt through the
alias in the device tree.
Signed-off-by: Manuel Kock <github.web@manu.li>
[rephrased commit title]
Signed-off-by: David Bauer <mail@david-bauer.net>
Includes following changes:
9d9d4c284786 fix possible garbage in unitialized char* struct members
dbc1b1b71b24 fix possible copy of null buffer and validation of unitialized header
76d53deef8bb crc32: add missing stdint.h dependency
e5666ed3b47c add cram based unit tests
abe0cf7de053 add initial GitLab CI support
e43042507b4f iron out extra compiler warnings
5df0cd6e1523 convert into CMake project
a7dc0526f819 refactor into separate Git project
adds missing PKG_LICENSE field and converts the package build to utilize
CMake.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
These targets are currently using more or less same SIGNATURE variable
which provides unique partition ID/signature, so it makes sense to
refactor it out into common IMG_PART_SIGNATURE variable which could be
reused by all targets.
This is another step in the direction of reproducible OpenWrt images.
Signed-off-by: Paul Spooren <mail@aparcar.org>
[split into separate commit, renamed to IMG_PART_SIGNATURE]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
x86, mvebu and tegra targets are currently using more or less same
SIGNATURE variable which provides unique partition ID/signature, so it
makes sense to refactor it out into common variable which could be
reused by all targets. While at it, make the content of the variable
reproducible.
Ref: http://lists.infradead.org/pipermail/openwrt-devel/2019-March/016148.html
Signed-off-by: Paul Spooren <mail@aparcar.org>
Suggested-by: Jo-Philipp Wich <jo@mein.io>
[renamed to IMG_PARTSIGNATURE, reworked with epoch+vermagic hash]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
As started in 19724e28c8 ("ramips: split base-files into
subtargets"), this moves some smaller left-over files to the
appropriate base-files folder of their subtarget:
- /etc/init.d/bootcount
- /etc/uci-defaults/04_led_migration
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
When Nanostation M was renamed from ubnt,nano-m to ubnt,nanostation-m
in commit f1396ac753 ("ath79: align naming of Ubiquiti Nanostation M"),
the caldata extraction in 10-ath9k-eeprom was overlooked.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This adjusts the GPIO state flag to ACTIVE_LOW as FCC pictures indicate
the base board is identical to the one of the R6220.
Fixes commit 3459013257 ("ramips: correct R6220 button flag")
Signed-off-by: David Bauer <mail@david-bauer.net>
Instead of depending on kmod-usb2 make it depend on the normal USB
dependencies. This should hopefully fix some problems seen in the build
bot builds for powerpc_8540.
In addition also activate DRIVER_11N_SUPPORT support.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
All buttons on the Netgear R6220 are active-low while they are flagged
as active-high.
The GPIO status reads the following for no buttons pressed:
root@64367-r6220:~# cat /sys/kernel/debug/gpio
gpio-7 ( |wps ) in hi
gpio-8 ( |wifi ) in hi
gpio-14 ( |reset ) in hi
Signed-off-by: David Bauer <mail@david-bauer.net>
lib and includedir point to the host, not staging_dir.
Note that prefix and exec_prefix is overriden to point to staging_dir.
As CMAKE_INSTTALL is passed, switched InstallDev to use cmake.mk's rule.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
includedir and libdir are set to /usr/include and /usr/lib . This breaks
compilation with packages such as tmux that use pkgconfig to find libevent
Also added PKG_LICENSE_FILES.
Simplified the InstallDev section by using cmake.mk's default rule.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Forward the OpenWrt TARGET_LDFLAGS to the linker of the fw_printenv tool.
In addition also use the more standard make invocation script.
With this change the fw_printenv tool is built with PIE and Full RELRO
support when activated globally in OpenWrt.
Signed-off-by: Hauke Mehrtens <hauke.mehrtens@intel.com>
Update busybox to 1.31.1
Small bug fix release. Fixes for dc, ash (PS1 expansion fix),
hush, dpkg-deb, telnet and wget.
No need to refresh patches or config.
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
The I2SE Duckbill devices are pen-drive like and thus the usage
of the USB gadget subsystem is highly indicated.
Spawning a console if a serial gadget is configured saves
us from connecting a physical debug uart.
On Olimex OLinuXino Maxi/Mini boards, this does not hurt.
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
Now that 'start-console' procd command has reached the main repo,
we can add a rule to start consoles on serial devices which are
created when USB gadget driver reports creation with hotplugging.
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
Also remove kernel 4.14 support and the meanwhile obsolete patch.
This was run-tested on I2SE Duckbill device and
Olimex OLinuXino Maxi board.
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
Tested-by: Zoltan HERPAI <wigyori@uid0.hu>
Also update the U-Boot BSP patch for I2SE Duckbill devices.
Run tested on I2SE Duckbill and Olimex OLinuXino Maxi boards.
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
This decreases the size of the usign application by 16% on MIPS BE.
old:
24,597 /usr/bin/usign
new:
20,501 /usr/bin/usign
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This decreases the size of the swconfig application by 25% on MIPS BE.
old:
16,916 /sbin/swconfig
new:
12,565 /sbin/swconfig
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This decreases the size of the mtd application by 25% on MIPS BE.
old:
20,597 /sbin/mtd
new:
16,421 /sbin/mtd
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This decreases the binary size when PIE ASLR is activated by 8% on MIPS BE.
old:
202,020 /usr/sbin/dnsmasq
new:
185,676 /usr/sbin/dnsmasq
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
