Import commit "ubi: Fix failure attaching when vid_hdr offset equals to
(sub)page size" which did not yet make it to stable upstream Linux trees.
Fixes: #12232Fixes: #12339
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Now that new pinconf features have been backported sync pinctrl-mt7981
and pinctrl-m7986 with bleeding-edge upstream versions.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Backport new features for MediaTek pinctrl/pinconf drivers from upstream.
This will serve as the base to improve pinconf bias/pull-up/pull-down on
MT7981 and MT7986, and also prepare for upcoming support for MT7988.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Avoid MCU getting "command reply receive timed out" message when LED
configuration setting trigger function is enabled in heartbeat mode.
Signed-off-by: Ian Chang <ianchang@ieiworld.com>
It appears that the refactor of the upgrade process for NAND devices resulted in the nand_do_upgrade_success step not being called for
devices using the linksys.sh script. As a result, configuration was
not preserved over sysupgrade steps.
This corrects a typo in the call of nand_do_upgrade_failed for ipq40xx
and ipq806x devices using the linksys.sh script.
Fixes: 8634c1080d ("ipq40xx: Fix Linksys upgrade, restore config step")
Fixes: 2715aff5df ("ipq806x: Fix Linksys upgrade, restore config step")
Signed-off-by: Michael Trinidad <trinidude4@hotmail.com>
It appears that the refactor of the upgrade process for NAND devices resulted in the nand_do_upgrade_success step not being called for
devices using the linksys.sh script. As a result, configuration was
not preserved over sysupgrade steps.
This restores the preservation of configs for mvebu/cortexa9 devices using the
linksys.sh script.
Fixes: e25e6d8e54 ("base-files: fix and clean up nand sysupgrade code")
Signed-off-by: Michael Trinidad <trinidude4@hotmail.com>
It appears that the refactor of the upgrade process for NAND devices
resulted in the nand_do_upgrade_success step not being called for
devices using the linksys.sh script. As a result, configuration was
not preserved over sysupgrade steps.
This restores the preservation of configs for kirkwood devices using the
linksys.sh script.
Fixes: e25e6d8e54 ("base-files: fix and clean up nand sysupgrade code")
Fixes: #12298
Signed-off-by: Michael Trinidad <trinidude4@hotmail.com>
Getting ready for the next release.
Signed-off-by: Paul Spooren <mail@aparcar.org>
[rmilecki: tested on GT-AC5300: boot, sysupgrade & 940 Mbps NAT]
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
bmips target is now more stable and it's time to start generating buildbot
images in order to receive a wider testing, which will be essential to replace
bcm63xx target in the future.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
BMIPS is a generic arch that can be used for multiple Broadcom SoCs, each one
with its own specific drivers, so instead of having a huge kernel supporting
all of them, let's switch to a subtarget per SoC like other OpenWrt targets.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Add BCM6328 and BCM6358 LED kernel modules.
This allows selecting the LED controllers only for those devices using them.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Sercomm SHG2500 is a BCM63168 with 128M of RAM, 256M of NAND, an external
BCM53124S switch for the LAN ports and internal/external Broadcom wifi.
LEDs are connected to an external MSP430G2513 MCU controlled via SPI.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Make use of sercomm-pid script for generating the Sercomm PID, which avoids
having to add an array of hex bytes for every new Sercomm device.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SERCOMM_VERSION is ambiguous and it should be more clear that it refers to the
version used for the filesystem.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Instead of passing an array of hex bytes for the Sercomm PID we can now use
the --pid-file parameter.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Hardware
--------
SoC: NXP P1010 (1x e500 @ 800MHz)
RAM: 256M DDR3 (2x Samsung K4B1G1646G-BCH9)
FLASH: 32M NOR (Spansion S25FL256S)
BTN: 1x Reset
WiFi: 1x Atheros AR9590 2.4 bgn 3x3
2x Atheros AR9590 5.0 an 3x3
ETH: 2x Gigabit Ethernet (Atheros AR8033 / AR8035)
UART: 115200 8N1 (RJ-45 Cisco)
Installation
------------
1. Grab the OpenWrt initramfs, rename it to ap3715.bin. Place it in
the root directory of a TFTP server and serve it at
192.168.1.66/24.
2. Connect to the serial port and boot the AP. Stop autoboot in U-Boot
by pressing Enter when prompted. Credentials are identical to the one
in the APs interface. By default it is admin / new2day.
3. Alter the bootcmd in U-Boot:
$ setenv ramboot_openwrt "setenv ipaddr 192.168.1.1;
setenv serverip 192.168.1.66; tftpboot 0x2000000 ap3715.bin; bootm"
$ setenv boot_openwrt "sf probe 0; sf read 0x2000000 0x140000 0x1000000;
bootm 0x2000000"
$ setenv bootcmd "run boot_openwrt"
$ saveenv
4. Boot the initramfs image
$ run ramboot_openwrt
5. Transfer the OpenWrt sysupgrade image to the AP using SCP. Install
using sysupgrade.
$ sysupgrade -n <path-to-sysupgrade.bin>
Signed-off-by: David Bauer <mail@david-bauer.net>
The kernel is already compressed with XZ by the bootwrapper, thus we
gain nothing by compressing it a second time.
Signed-off-by: David Bauer <mail@david-bauer.net>
The bootpage for the second core is placed by U-Boot in the upper 128k
of syste-memory.
This could either be a reserved-area or deducted from the total
system-memory. As only the latter is parsed by the bootwrapper, reduce
the available system memory for linux in order to preserve the bootpage
from being overwritten.
Signed-off-by: David Bauer <mail@david-bauer.net>
Kernel 5.10 builds currently fail because the patch for using the
simpleImage bootwrapper were not added to 5.10.
Signed-off-by: David Bauer <mail@david-bauer.net>
This adds properties to PCIe as well as ethernet nodes which are
normally added by the Extreme Networks U-Boot.
Signed-off-by: David Bauer <mail@david-bauer.net>
This adds properties normally filled by U-Boot. Also it fixes the node
name, which is incorrectly referring to a P1010 core.
Signed-off-by: David Bauer <mail@david-bauer.net>
This is normally filled by U-Boot. Prevents double-printing of early
console messages. Also enables debug-output by the zImage wrapper.
Signed-off-by: David Bauer <mail@david-bauer.net>
Prevent the BBT translation layer from remapping the UBI used for
storing rootfs.
Explicitly define the number of blocks reserved for remapping.
Signed-off-by: David Bauer <mail@david-bauer.net>
Fix mis-typed DEVICE-MODEL in mk file for EnGenius EWS2910P.
Signed-off-by: Raylynn Knight <rayknight@me.com>
[ fix wrong SoB format and improve commit title/description ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
They add NVMEM layouts support. It allows handling NVMEM content
independently of NVMEM device access.
Skip U-Boot env data patch for now as it break our downstream MAC hacks.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
We need to reset KERNEL_LOADADDR if we use it on a per-device base.
Otherwise the previous value will be kept in case a device doesn't
define KERNEL_LOADADDR and relies on the default.
Move initializing KERNEL_LOADADDR to target/linux/mediatek/image/Makefile,
similar to how it's done also on the ramips target.
This fixes image size related breakage on devices which rely on the
default value of KERNEL_LOADADDR.
While at it use 0x48000000 which is more common than the previous default
0x44000000 for the filogic subtarget.
Fixed: e7c399bee6 ("filogic: add support for ASUS TUF-AX4200")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
MAC drivers don't use SGMII in-band autonegotiation unless told to do so
in device tree using 'managed = "in-band-status"'. When using MDIO to
access a PHY, in-band-status is unneeded as we have link-status via
MDIO. Switch off SGMII in-band autonegotiation using magic values.
Reported-by: Chen Minqiang <ptpt52@gmail.com>
Reported-by: Chukun Pan <amadeus@jmu.edu.cn>
Reported-by: Yevhen Kolomeiko <jarvis2709@gmail.com>
Tested-by: Yevhen Kolomeiko <jarvis2709@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Some vendor bootloaders do weird things with those PHYs which result in
link modes being reported wrongly. Start from a clean sheet by resetting
the PHY.
Reported-by: Yevhen Kolomeiko <jarvis2709@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add dynamic interface mode update for the rtl8221 phy to match various
wire speeds. 10M/100M/1000M use SGMII, 2500M uses 2500Base-X.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Refresh patches which were no longer applying cleanly after a recently
added SFP quirk.
Fixes: 658b45ce48 ("generic: add quirk for HG MXPD-483II 2500M fiber SFP")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
