Add patch fixing compilation warning for switch fallthrough and
copy_to_user ret not handled.
Fix compilation warning:
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_tapi-3.13.0/src/drv_tapi_dial.c: In function 'ifx_tapi_dial_OnTimer':
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_tapi-3.13.0/src/drv_tapi_dial.c:318:38: error: this statement may fall through [-Werror=implicit-fallthrough=]
318 | pTapiDialData->nHookChanges = 0;
| ~~~~~~~~~~~~~~~~~~~~~~~~~~~~^~~
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_tapi-3.13.0/src/drv_tapi_dial.c:322:7: note: here
322 | case TAPI_HOOK_STATE_DIAL_L_VAL:
| ^~~~
cc1: all warnings being treated as errors
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_tapi-3.13.0/src/drv_tapi_event.c: In function 'IFX_TAPI_Event_Dispatch_ProcessCtx':
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_tapi-3.13.0/src/drv_tapi_event.c:1546:30: error: this statement may fall through [-Werror=implicit-fallthrough=]
1546 | pEvent->ch = IFX_TAPI_DEVICE_CH_NUMBER;
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_tapi-3.13.0/src/drv_tapi_event.c:1548:16: note: here
1548 | case IFX_TAPI_ERRSRC_LL_CH:
| ^~~~
cc1: all warnings being treated as errors
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_tapi-3.13.0/src/drv_tapi_ioctl.c: In function 'TAPI_IoctlDev':
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_tapi-3.13.0/src/drv_tapi_ioctl.c:705:19: error: ignoring return value of 'copy_to_user' declared with attribute 'warn_unused_result' [-Werror=unused-result]
705 | copy_to_user ((IFX_void_t*)ioarg, p_tmp, sizeof(IFX_TAPI_CAP_t));
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_tapi-3.13.0/src/drv_tapi_ioctl.c: In function 'TAPI_IoctlCh':
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_tapi-3.13.0/src/drv_tapi_ioctl.c:1553:14: error: this statement may fall through [-Werror=implicit-fallthrough=]
1553 | ret = TAPI_statusNotSupported;
| ~~~~^~~~~~~~~~~~~~~~~~~~~~~~~
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_tapi-3.13.0/src/drv_tapi_ioctl.c:1555:7: note: here
1555 | default:
| ^~~~~~~
cc1: all warnings being treated as errors
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_tapi-3.13.0/src/drv_tapi_cid.c: In function 'cid_fsm_alert_exec':
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_tapi-3.13.0/src/drv_tapi_cid.c:2037:31: error: this statement may fall through [-Werror=implicit-fallthrough=]
2037 | pTxData->nCidSubState++;
| ~~~~~~~~~~~~~~~~~~~~~^~
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_tapi-3.13.0/src/drv_tapi_cid.c:2039:7: note: here
2039 | case 1:
| ^~~~
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_tapi-3.13.0/src/drv_tapi_cid.c:2053:31: error: this statement may fall through [-Werror=implicit-fallthrough=]
2053 | pTxData->nCidSubState++;
| ~~~~~~~~~~~~~~~~~~~~~^~
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_tapi-3.13.0/src/drv_tapi_cid.c:2055:7: note: here
2055 | case 2:
| ^~~~
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_tapi-3.13.0/src/drv_tapi_cid.c:2070:31: error: this statement may fall through [-Werror=implicit-fallthrough=]
2070 | pTxData->nCidSubState++;
| ~~~~~~~~~~~~~~~~~~~~~^~
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_tapi-3.13.0/src/drv_tapi_cid.c:2072:7: note: here
2072 | default:
| ^~~~~~~
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_tapi-3.13.0/src/drv_tapi_cid.c: In function 'cid_prepare_data':
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_tapi-3.13.0/src/drv_tapi_cid.c:1501:13: error: this statement may fall through [-Werror=implicit-fallthrough=]
1501 | if (IFX_TAPI_CID_HM_ONHOOK == pTxData->txHookMode)
| ^
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_tapi-3.13.0/src/drv_tapi_cid.c:1509:7: note: here
1509 | default:
| ^~~~~~~
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_tapi-3.13.0/src/drv_tapi_cid.c:1531:16: error: this statement may fall through [-Werror=implicit-fallthrough=]
1531 | if (IFX_TAPI_CID_STD_KPN_DTMF_FSK != pConfData->nStandard)
| ^
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_tapi-3.13.0/src/drv_tapi_cid.c:1535:10: note: here
1535 | case IFX_TAPI_CID_GEN_TYPE_FSK:
| ^~~~
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_tapi-3.13.0/src/drv_tapi_cid.c: In function 'cid_lookup_transparent':
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_tapi-3.13.0/src/drv_tapi_cid.c:1425:10: error: this statement may fall through [-Werror=implicit-fallthrough=]
1425 | cidfsk_set_tx_time (pTxData, &pConfData->TapiCidFskConf);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_tapi-3.13.0/src/drv_tapi_cid.c:1427:7: note: here
1427 | case IFX_TAPI_CID_GEN_TYPE_DTMF:
| ^~~~
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_tapi-3.13.0/src/drv_tapi_cid.c: In function 'TAPI_Phone_CID_Stop_Tx':
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_tapi-3.13.0/src/drv_tapi_cid.c:3445:10: error: this statement may fall through [-Werror=implicit-fallthrough=]
3445 | switch (pTxData->nAlertType)
| ^~~~~~
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_tapi-3.13.0/src/drv_tapi_cid.c:3461:7: note: here
3461 | case TAPI_CID_STATE_ACK:
| ^~~~
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_tapi-3.13.0/src/drv_tapi_cid.c:3463:13: error: this statement may fall through [-Werror=implicit-fallthrough=]
3463 | if (ptr_chk(pDrvCtx->SIG.DTMFD_Override, ""))
| ^
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_tapi-3.13.0/src/drv_tapi_cid.c:3472:7: note: here
3472 | case TAPI_CID_STATE_SENDING:
| ^~~~
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_tapi-3.13.0/src/drv_tapi_cid.c: In function 'TAPI_Phone_Get_CidRxData':
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_tapi-3.13.0/src/drv_tapi_cid.c:4060:10: error: this statement may fall through [-Werror=implicit-fallthrough=]
4060 | if (IFX_Fifo_isEmpty(&(pCidRx->TapiCidRxFifo)))
| ^
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_tapi-3.13.0/src/drv_tapi_cid.c:4069:4: note: here
4069 | default:
| ^~~~~~~
cc1: all warnings being treated as errors
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Fix compilation warning caused by copy_from_user ret not handled.
Fix compilation warning:
/__w/openwrt/openwrt/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_ase/ltq-atm-ase/ltq-atm/ltq_atm.c: In function 'ppe_ioctl':
/__w/openwrt/openwrt/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_ase/ltq-atm-ase/ltq-atm/ltq_atm.c:341:17: error: ignoring return value of 'copy_from_user' declared with attribute 'warn_unused_result' [-Werror=unused-result]
341 | copy_from_user(&mib_vcc, arg, sizeof(mib_vcc));
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add patch fixing compilation warning from missing fallthrough
Fix compilation warning:
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-arm-openwrt-linux-muslgnueabi_musl/linux-ipq40xx_generic/dsl_cpe_api-ugw_8.5.2.10/src/common/drv_dsl_cpe_api.c: In function 'DSL_DRV_AutobootControlSet':
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-arm-openwrt-linux-muslgnueabi_musl/linux-ipq40xx_generic/dsl_cpe_api-ugw_8.5.2.10/src/common/drv_dsl_cpe_api.c:2648:19: error: this statement may fall through [-Werror=implicit-fallthrough=]
2648 | if (pContext->bAutobootThreadStarted)
| ^
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-arm-openwrt-linux-muslgnueabi_musl/linux-ipq40xx_generic/dsl_cpe_api-ugw_8.5.2.10/src/common/drv_dsl_cpe_api.c:2656:13: note: here
2656 | case DSL_AUTOBOOT_CTRL_STOP_PD:
| ^~~~
cc1: all warnings being treated as errors
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-arm-openwrt-linux-muslgnueabi_musl/linux-ipq40xx_generic/dsl_cpe_api-ugw_8.5.2.10/src/pm/drv_dsl_cpe_pm_core.c: In function 'DSL_DRV_PM_CountersReset':
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-arm-openwrt-linux-muslgnueabi_musl/linux-ipq40xx_generic/dsl_cpe_api-ugw_8.5.2.10/src/pm/drv_dsl_cpe_pm_core.c:2358:7: error: this statement may fall through [-Werror=implicit-fallthrough=]
2358 | if (ResetType == DSL_PM_RESET_HISTORY)
| ^
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-arm-openwrt-linux-muslgnueabi_musl/linux-ipq40xx_generic/dsl_cpe_api-ugw_8.5.2.10/src/pm/drv_dsl_cpe_pm_core.c:2361:4: note: here
2361 | case DSL_PM_RESET_TOTAL:
| ^~~~
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-arm-openwrt-linux-muslgnueabi_musl/linux-ipq40xx_generic/dsl_cpe_api-ugw_8.5.2.10/src/pm/drv_dsl_cpe_pm_core.c:2365:7: error: this statement may fall through [-Werror=implicit-fallthrough=]
2365 | if (ResetType == DSL_PM_RESET_TOTAL)
| ^
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-arm-openwrt-linux-muslgnueabi_musl/linux-ipq40xx_generic/dsl_cpe_api-ugw_8.5.2.10/src/pm/drv_dsl_cpe_pm_core.c:2368:4: note: here
2368 | case DSL_PM_RESET_HISTORY_SHOWTIME:
| ^~~~
cc1: all warnings being treated as errors
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-arm-openwrt-linux-muslgnueabi_musl/linux-ipq40xx_generic/dsl_cpe_api-ugw_8.5.2.10/src/device/drv_dsl_cpe_device_vrx.c: In function 'DSL_DRV_DEV_AutobootHandleTraining':
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-arm-openwrt-linux-muslgnueabi_musl/linux-ipq40xx_generic/dsl_cpe_api-ugw_8.5.2.10/src/device/drv_dsl_cpe_device_vrx.c:8883:19: error: this statement may fall through [-Werror=implicit-fallthrough=]
8883 | bPreFail = DSL_TRUE;
| ~~~~~~~~~^~~~~~~~~~
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-arm-openwrt-linux-muslgnueabi_musl/linux-ipq40xx_generic/dsl_cpe_api-ugw_8.5.2.10/src/device/drv_dsl_cpe_device_vrx.c:8889:7: note: here
8889 | case DSL_LINESTATE_EXCEPTION:
| ^~~~
cc1: all warnings being treated as errors
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add patch fixing compilation warning for some debugfs entry defined but
unused.
Fix compilation warning:
/__w/openwrt/openwrt/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/ltq-ptm-danube/ltq-ptm/ifxmips_ptm_adsl.c:969:12: error: 'proc_read_genconf' defined but not used [-Werror=unused-function]
969 | static int proc_read_genconf(char *page, char **start, off_t off, int count, int *eof, void *data)
| ^~~~~~~~~~~~~~~~~
/__w/openwrt/openwrt/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/ltq-ptm-danube/ltq-ptm/ifxmips_ptm_adsl.c:942:12: error: 'proc_write_wanmib' defined but not used [-Werror=unused-function]
942 | static int proc_write_wanmib(struct file *file, const char *buf, unsigned long count, void *data)
| ^~~~~~~~~~~~~~~~~
/__w/openwrt/openwrt/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/ltq-ptm-danube/ltq-ptm/ifxmips_ptm_adsl.c:910:12: error: 'proc_read_wanmib' defined but not used [-Werror=unused-function]
910 | static int proc_read_wanmib(char *page, char **start, off_t off, int count, int *eof, void *data)
| ^~~~~~~~~~~~~~~~
/__w/openwrt/openwrt/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/ltq-ptm-danube/ltq-ptm/ifxmips_ptm_adsl.c:892:12: error: 'proc_read_version' defined but not used [-Werror=unused-function]
892 | static int proc_read_version(char *buf, char **start, off_t offset, int count, int *eof, void *data)
| ^~~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/ltq-ptm-danube/ltq-ptm/ifxmips_ptm_adsl.c:1164:19: error: 'stricmp' defined but not used [-Werror=unused-function]
1164 | static INLINE int stricmp(const char *p1, const char *p2)
| ^~~~~~~
cc1: all warnings being treated as errors
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add patch fixing compilation warning due to not handled switch
fallthrough, stack limit and compilation warning in g997 module.
Fix compilation warning:
/__w/openwrt/openwrt/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_ase/ltq-dsl-ase/drv_dsl_cpe_api-3.24.4.4/src/pm/drv_dsl_cpe_pm_core.c: In function 'DSL_DRV_PM_CountersReset':
/__w/openwrt/openwrt/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_ase/ltq-dsl-ase/drv_dsl_cpe_api-3.24.4.4/src/pm/drv_dsl_cpe_pm_core.c:2277:7: error: this statement may fall through [-Werror=implicit-fallthrough=]
2277 | if (ResetType == DSL_PM_RESET_HISTORY)
| ^
/__w/openwrt/openwrt/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_ase/ltq-dsl-ase/drv_dsl_cpe_api-3.24.4.4/src/pm/drv_dsl_cpe_pm_core.c:2280:4: note: here
2280 | case DSL_PM_RESET_TOTAL:
| ^~~~
/__w/openwrt/openwrt/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_ase/ltq-dsl-ase/drv_dsl_cpe_api-3.24.4.4/src/pm/drv_dsl_cpe_pm_core.c:2284:7: error: this statement may fall through [-Werror=implicit-fallthrough=]
2284 | if (ResetType == DSL_PM_RESET_TOTAL)
| ^
/__w/openwrt/openwrt/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_ase/ltq-dsl-ase/drv_dsl_cpe_api-3.24.4.4/src/pm/drv_dsl_cpe_pm_core.c:2287:4: note: here
2287 | case DSL_PM_RESET_HISTORY_SHOWTIME:
| ^~~~
cc1: all warnings being treated as errors
/__w/openwrt/openwrt/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_ase/ltq-dsl-ase/drv_dsl_cpe_api-3.24.4.4/src/device/drv_dsl_cpe_device_danube.c: In function 'DSL_DRV_DEV_AutobootHandleTraining':
/__w/openwrt/openwrt/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_ase/ltq-dsl-ase/drv_dsl_cpe_api-3.24.4.4/src/device/drv_dsl_cpe_device_danube.c:3189:19: error: this statement may fall through [-Werror=implicit-fallthrough=]
3189 | if (nErrCode != DSL_SUCCESS)
| ^
/__w/openwrt/openwrt/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_ase/ltq-dsl-ase/drv_dsl_cpe_api-3.24.4.4/src/device/drv_dsl_cpe_device_danube.c:3197:13: note: here
3197 | case DSL_LINESTATE_IDLE:
| ^~~~
cc1: all warnings being treated as errors
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_ase/ltq-dsl-ase/drv_dsl_cpe_api-3.24.4.4/src/g997/drv_dsl_cpe_api_g997_danube.c: In function 'DSL_DRV_DEV_G997_PowerManagementStateForcedTrigger':
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_ase/ltq-dsl-ase/drv_dsl_cpe_api-3.24.4.4/src/g997/drv_dsl_cpe_api_g997_danube.c:2532:52: error: bitwise comparison always evaluates to false [-Werror=tautological-compare]
2532 | else if (((nVal >> 4) & 0x15) == 0x9)
| ^~
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_ase/ltq-dsl-ase/drv_dsl_cpe_api-3.24.4.4/src/g997/drv_dsl_cpe_api_g997_danube.c: In function 'DSL_DRV_DEV_G997_DeltHlogGet':
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_ase/ltq-dsl-ase/drv_dsl_cpe_api-3.24.4.4/src/g997/drv_dsl_cpe_api_g997_danube.c:2108:1: error: the frame size of 1056 bytes is larger than 1024 bytes [-Werror=frame-larger-than=]
2108 | }
| ^
cc1: all warnings being treated as errors
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add multiple patch to make the package compilable again.
Aside from some fixup of obvius wrong code, some real fix were needed.
This fix any compilation warning found on compiling the package on
bcm47xx. (omitted since they are too much)
The real problem of this package was the missing MODULE_LICENSE now
mandatory even without WERROR. Set to Proprietary.
And the big blocker is that Broadcom provided an object file targetting
an old kernel version.
The module on modprobe try to find the symbol printk but printk was
dropped and replaced to _printk.
To handle this change we use objcopy tool to rename the symbol to the
new name permitting a correct modprobe and creation of .ko
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add patch fixing compilation warning on 64bit systems.
Fix compilation warning:
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-aarch64_cortex-a53_musl/linux-ipq807x_generic/mwlwifi-2023-04-29-6a436714/hif/fwcmd.c: In function 'mwl_fwcmd_get_fw_core_dump':
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-aarch64_cortex-a53_musl/linux-ipq807x_generic/mwlwifi-2023-04-29-6a436714/hif/fwcmd.c:3608:31: error: cast from pointer to integer of different size [-Werror=pointer-to-int-cast]
3608 | (const void *)((u32)pcmd +
| ^
In file included from ./include/linux/device.h:15,
from /home/ansuel/openwrt-ansuel/openwrt/staging_dir/target-aarch64_cortex-a53_musl/usr/include/mac80211-backport/linux/device.h:3,
from ./include/linux/dma-mapping.h:7,
from /home/ansuel/openwrt-ansuel/openwrt/staging_dir/target-aarch64_cortex-a53_musl/usr/include/mac80211-backport/linux/dma-mapping.h:3,
from ./include/linux/skbuff.h:31,
from /home/ansuel/openwrt-ansuel/openwrt/staging_dir/target-aarch64_cortex-a53_musl/usr/include/mac80211-backport/linux/skbuff.h:3,
from ./include/linux/if_ether.h:19,
from /home/ansuel/openwrt-ansuel/openwrt/staging_dir/target-aarch64_cortex-a53_musl/usr/include/mac80211-backport/linux/if_ether.h:3,
from ./include/linux/etherdevice.h:20,
from /home/ansuel/openwrt-ansuel/openwrt/staging_dir/target-aarch64_cortex-a53_musl/usr/include/mac80211-backport/linux/etherdevice.h:3,
from /home/ansuel/openwrt-ansuel/openwrt/build_dir/target-aarch64_cortex-a53_musl/linux-ipq807x_generic/mwlwifi-2023-04-29-6a436714/hif/pcie/tx_ndp.c:20:
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-aarch64_cortex-a53_musl/linux-ipq807x_generic/mwlwifi-2023-04-29-6a436714/hif/pcie/tx_ndp.c: In function 'pcie_tx_init_ndp':
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-aarch64_cortex-a53_musl/linux-ipq807x_generic/mwlwifi-2023-04-29-6a436714/hif/pcie/tx_ndp.c:338:38: error: format '%d' expects argument of type 'int', but argument 3 has type 'long unsigned int' [-Werror=format=]
338 | wiphy_err(hw->wiphy, "driver data is not enough: %d (%d)\n",
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
./include/linux/dev_printk.h:110:30: note: in definition of macro 'dev_printk_index_wrap'
110 | _p_func(dev, fmt, ##__VA_ARGS__); \
| ^~~
./include/linux/dev_printk.h:144:56: note: in expansion of macro 'dev_fmt'
144 | dev_printk_index_wrap(_dev_err, KERN_ERR, dev, dev_fmt(fmt), ##__VA_ARGS__)
| ^~~~~~~
/home/ansuel/openwrt-ansuel/openwrt/staging_dir/target-aarch64_cortex-a53_musl/usr/include/mac80211/net/cfg80211.h:8828:9: note: in expansion of macro 'dev_err'
8828 | dev_err(&(wiphy)->dev, format, ##args)
| ^~~~~~~
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-aarch64_cortex-a53_musl/linux-ipq807x_generic/mwlwifi-2023-04-29-6a436714/hif/pcie/tx_ndp.c:338:17: note: in expansion of macro 'wiphy_err'
338 | wiphy_err(hw->wiphy, "driver data is not enough: %d (%d)\n",
| ^~~~~~~~~
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-aarch64_cortex-a53_musl/linux-ipq807x_generic/mwlwifi-2023-04-29-6a436714/hif/pcie/tx_ndp.c:338:67: note: format string is defined here
338 | wiphy_err(hw->wiphy, "driver data is not enough: %d (%d)\n",
| ~^
| |
| int
| %ld
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-aarch64_cortex-a53_musl/linux-ipq807x_generic/mwlwifi-2023-04-29-6a436714/hif/pcie/tx_ndp.c:338:38: error: format '%d' expects argument of type 'int', but argument 4 has type 'long unsigned int' [-Werror=format=]
338 | wiphy_err(hw->wiphy, "driver data is not enough: %d (%d)\n",
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
./include/linux/dev_printk.h:110:30: note: in definition of macro 'dev_printk_index_wrap'
110 | _p_func(dev, fmt, ##__VA_ARGS__); \
| ^~~
./include/linux/dev_printk.h:144:56: note: in expansion of macro 'dev_fmt'
144 | dev_printk_index_wrap(_dev_err, KERN_ERR, dev, dev_fmt(fmt), ##__VA_ARGS__)
| ^~~~~~~
/home/ansuel/openwrt-ansuel/openwrt/staging_dir/target-aarch64_cortex-a53_musl/usr/include/mac80211/net/cfg80211.h:8828:9: note: in expansion of macro 'dev_err'
8828 | dev_err(&(wiphy)->dev, format, ##args)
| ^~~~~~~
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-aarch64_cortex-a53_musl/linux-ipq807x_generic/mwlwifi-2023-04-29-6a436714/hif/pcie/tx_ndp.c:338:17: note: in expansion of macro 'wiphy_err'
338 | wiphy_err(hw->wiphy, "driver data is not enough: %d (%d)\n",
| ^~~~~~~~~
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-aarch64_cortex-a53_musl/linux-ipq807x_generic/mwlwifi-2023-04-29-6a436714/hif/pcie/tx_ndp.c:338:71: note: format string is defined here
338 | wiphy_err(hw->wiphy, "driver data is not enough: %d (%d)\n",
| ~^
| |
| int
| %ld
CC [M] /home/ansuel/openwrt-ansuel/openwrt/build_dir/target-aarch64_cortex-a53_musl/linux-ipq807x_generic/mwlwifi-2023-04-29-6a436714/debugfs.o
In file included from ./include/linux/device.h:15,
from /home/ansuel/openwrt-ansuel/openwrt/staging_dir/target-aarch64_cortex-a53_musl/usr/include/mac80211-backport/linux/device.h:3,
from ./include/linux/dma-mapping.h:7,
from /home/ansuel/openwrt-ansuel/openwrt/staging_dir/target-aarch64_cortex-a53_musl/usr/include/mac80211-backport/linux/dma-mapping.h:3,
from ./include/linux/skbuff.h:31,
from /home/ansuel/openwrt-ansuel/openwrt/staging_dir/target-aarch64_cortex-a53_musl/usr/include/mac80211-backport/linux/skbuff.h:3,
from ./include/linux/if_ether.h:19,
from /home/ansuel/openwrt-ansuel/openwrt/staging_dir/target-aarch64_cortex-a53_musl/usr/include/mac80211-backport/linux/if_ether.h:3,
from ./include/linux/etherdevice.h:20,
from /home/ansuel/openwrt-ansuel/openwrt/staging_dir/target-aarch64_cortex-a53_musl/usr/include/mac80211-backport/linux/etherdevice.h:3,
from /home/ansuel/openwrt-ansuel/openwrt/build_dir/target-aarch64_cortex-a53_musl/linux-ipq807x_generic/mwlwifi-2023-04-29-6a436714/hif/pcie/pcie.c:19:
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-aarch64_cortex-a53_musl/linux-ipq807x_generic/mwlwifi-2023-04-29-6a436714/hif/pcie/pcie.c: In function 'pcie_bf_mimo_ctrl_decode':
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-aarch64_cortex-a53_musl/linux-ipq807x_generic/mwlwifi-2023-04-29-6a436714/hif/pcie/pcie.c:1325:37: error: cast from pointer to integer of different size [-Werror=pointer-to-int-cast]
1325 | filename, (unsigned int)fp_data);
| ^
./include/linux/dev_printk.h:110:37: note: in definition of macro 'dev_printk_index_wrap'
110 | _p_func(dev, fmt, ##__VA_ARGS__); \
| ^~~~~~~~~~~
/home/ansuel/openwrt-ansuel/openwrt/staging_dir/target-aarch64_cortex-a53_musl/usr/include/mac80211/net/cfg80211.h:8828:9: note: in expansion of macro 'dev_err'
8828 | dev_err(&(wiphy)->dev, format, ##args)
| ^~~~~~~
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-aarch64_cortex-a53_musl/linux-ipq807x_generic/mwlwifi-2023-04-29-6a436714/hif/pcie/pcie.c:1324:17: note: in expansion of macro 'wiphy_err'
1324 | wiphy_err(priv->hw->wiphy, "Error opening %s! %x\n",
| ^~~~~~~~~
cc1: all warnings being treated as errors
make[4]: *** [scripts/Makefile.build:289: /home/ansuel/openwrt-ansuel/openwrt/build_dir/target-aarch64_cortex-a53_musl/linux-ipq807x_generic/mwlwifi-2023-04-29-6a436714/hif/pcie/tx_ndp.o] Error 1
make[4]: *** Waiting for unfinished jobs....
cc1: all warnings being treated as errors
make[4]: *** [scripts/Makefile.build:289: /home/ansuel/openwrt-ansuel/openwrt/build_dir/target-aarch64_cortex-a53_musl/linux-ipq807x_generic/mwlwifi-2023-04-29-6a436714/hif/pcie/pcie.o] Error 1
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-aarch64_cortex-a53_musl/linux-ipq807x_generic/mwlwifi-2023-04-29-6a436714/debugfs.c: In function 'mwl_debugfs_regrdwr_read':
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-aarch64_cortex-a53_musl/linux-ipq807x_generic/mwlwifi-2023-04-29-6a436714/debugfs.c:1335:43: error: format '%d' expects argument of type 'int', but argument 4 has type 'ssize_t' {aka 'long int'} [-Werror=format=]
1335 | "error: %d(%u 0x%08x 0x%08x)\n",
| ~^
| |
| int
| %ld
1336 | ret, priv->reg_type, priv->reg_offset,
| ~~~
| |
| ssize_t {aka long int}
cc1: all warnings being treated as errors
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Alloc MIB struct dynamically instead to fix compilation warning for
stack limit.
Fix compilation warning:
/__w/openwrt/openwrt/openwrt/build_dir/target-arm-openwrt-linux-muslgnueabi_musl/linux-ipq40xx_chromium/vrx518_tc_drv-ugw_8.5.2.10/dcdp/ptm_tc.c: In function 'ptm_tc_get_stats':
/__w/openwrt/openwrt/openwrt/build_dir/target-arm-openwrt-linux-muslgnueabi_musl/linux-ipq40xx_chromium/vrx518_tc_drv-ugw_8.5.2.10/dcdp/ptm_tc.c:463:1: error: the frame size of 1032 bytes is larger than 1024 bytes [-Werror=frame-larger-than=]
463 | }
| ^
cc1: all warnings being treated as errors
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add patch fixing compilation warning for atm_tc module.
Fix compilation warning:
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-arm-openwrt-linux-muslgnueabi_musl/linux-ipq40xx_generic/vrx518_tc_drv-ugw_8.5.2.10/dcdp/atm_tc.c: In function 'print_datetime':
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-arm-openwrt-linux-muslgnueabi_musl/linux-ipq40xx_generic/vrx518_tc_drv-ugw_8.5.2.10/dcdp/atm_tc.c:768:32: error: argument to 'sizeof' in 'snprintf' call is the same expression as the destination; did you mean to provide an explicit length? [-Werror=sizeof-pointer-memaccess]
768 | snprintf(buffer, sizeof(buffer), "%s.%06d", tmbuf, (int)datetime->tv_nsec / 1000);
| ^
cc1: all warnings being treated as errors
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Drop set_fs and get_fs since they are not present in kernel > 5.13.
Fix compilation warning:
/__w/openwrt/openwrt/openwrt/build_dir/target-mipsel-openwrt-linux-musl_musl/linux-bcm47xx_generic/broadcom-wl-5.10.56.27.3/driver/wl_iw.c: In function 'dev_wlc_ioctl':
/__w/openwrt/openwrt/openwrt/build_dir/target-mipsel-openwrt-linux-musl_musl/linux-bcm47xx_generic/broadcom-wl-5.10.56.27.3/driver/wl_iw.c:121:14: error: implicit declaration of function 'get_fs'; did you mean 'sget_fc'? [-Werror=implicit-function-declaration]
121 | fs = get_fs();
| ^~~~~~
| sget_fc
/__w/openwrt/openwrt/openwrt/build_dir/target-mipsel-openwrt-linux-musl_musl/linux-bcm47xx_generic/broadcom-wl-5.10.56.27.3/driver/wl_iw.c:121:14: error: incompatible types when assigning to type 'mm_segment_t' from type 'int'
/__w/openwrt/openwrt/openwrt/build_dir/target-mipsel-openwrt-linux-musl_musl/linux-bcm47xx_generic/broadcom-wl-5.10.56.27.3/driver/wl_iw.c:122:9: error: implicit declaration of function 'set_fs'; did you mean 'sget_fc'? [-Werror=implicit-function-declaration]
122 | set_fs(KERNEL_DS);
| ^~~~~~
| sget_fc
/__w/openwrt/openwrt/openwrt/build_dir/target-mipsel-openwrt-linux-musl_musl/linux-bcm47xx_generic/broadcom-wl-5.10.56.27.3/driver/wl_iw.c:122:16: error: 'KERNEL_DS' undeclared (first use in this function); did you mean 'KERNFS_NS'?
122 | set_fs(KERNEL_DS);
| ^~~~~~~~~
| KERNFS_NS
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add patch fixing compilation warning related to if clause not guarding in
wl_iw.c
Fix compilation warning:
/__w/openwrt/openwrt/openwrt/build_dir/target-mipsel-openwrt-linux-musl_musl/linux-bcm47xx_legacy/broadcom-wl-5.10.56.27.3/driver/wl_iw.c: In function 'wl_iw_set_freq':
/__w/openwrt/openwrt/openwrt/build_dir/target-mipsel-openwrt-linux-musl_musl/linux-bcm47xx_legacy/broadcom-wl-5.10.56.27.3/driver/wl_iw.c:393:9: error: this 'if' clause does not guard... [-Werror=misleading-indentation]
393 | if (fwrq->m > 4000 && fwrq->m < 5000)
| ^~
/__w/openwrt/openwrt/openwrt/build_dir/target-mipsel-openwrt-linux-musl_musl/linux-bcm47xx_legacy/broadcom-wl-5.10.56.27.3/driver/wl_iw.c:396:17: note: ...this statement, but the latter is misleadingly indented as if it were guarded by the 'if'
396 | chan = wf_mhz2channel(fwrq->m, sf);
| ^~~~
cc1: all warnings being treated as errors
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Fix compilation warning for copy_from_user ret value not handled.
Fix compilation warning:
/__w/openwrt/openwrt/openwrt/build_dir/target-mips_mips32_musl/linux-lantiq_ase/ltq-adsl-mei-ase/ltq-adsl-mei/drv_mei_cpe.c: In function 'DSL_BSP_FWDownload':
/__w/openwrt/openwrt/openwrt/build_dir/target-mips_mips32_musl/linux-lantiq_ase/ltq-adsl-mei-ase/ltq-adsl-mei/drv_mei_cpe.c:1623:17: error: ignoring return value of 'copy_from_user' declared with attribute 'warn_unused_result' [-Werror=unused-result]
1623 | copy_from_user ((char *) &img_hdr_tmp, buf, sizeof (img_hdr_tmp));
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
/__w/openwrt/openwrt/openwrt/build_dir/target-mips_mips32_musl/linux-lantiq_ase/ltq-adsl-mei-ase/ltq-adsl-mei/drv_mei_cpe.c:1701:17: error: ignoring return value of 'copy_from_user' declared with attribute 'warn_unused_result' [-Werror=unused-result]
1701 | copy_from_user (mem_ptr, buf + nRead, nCopy);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
If CPTCFG_BRCMFMAC_SDIO is not used brcmf_of_fwnames is defined but not
used in the case of CONFIG_OF not compiled.
Restrict brcmf_of_fwnames only with CPTCFG_BRCMFMAC_SDIO selected.
Fix compilation warning:
/__w/openwrt/openwrt/openwrt/build_dir/target-x86_64-openwrt-linux-musl_musl/linux-x86_64/backports-6.1.24/drivers/net/wireless/broadcom/brcm80211/brcmfmac/of.h:16:1: error: 'brcmf_of_fwnames' defined but not used [-Werror=unused-function]
16 | brcmf_of_fwnames(struct device *dev, u32 *map_count)
| ^~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add patch fixing compilation warning for debug level read.
Fix compilation warning:
/__w/openwrt/openwrt/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-malta_be/ath10k-ct-regular/ath10k-ct-2022-05-13-f808496f/ath10k-5.15/debug.c: In function 'ath10k_read_debug_level': /__w/openwrt/openwrt/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-malta_be/ath10k-ct-regular/ath10k-ct-2022-05-13-f808496f/ath10k-5.15/debug.c:1388:1: error: the frame size of 1440 bytes is larger than 1024 bytes [-Werror=frame-larger-than=]
1388 | }
| ^
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Handle error from copy_to_user in read_file_eeprom.
Fix compilarion warning:
/__w/openwrt/openwrt/openwrt/build_dir/target-x86_64-openwrt-linux-musl_musl/linux-x86_64/backports-6.1.24/drivers/net/wireless/ath/ath9k/debug.c: In function 'read_file_eeprom':
/__w/openwrt/openwrt/openwrt/build_dir/target-x86_64-openwrt-linux-musl_musl/linux-x86_64/backports-6.1.24/drivers/net/wireless/ath/ath9k/debug.c:1451:17: error: ignoring return value of 'copy_to_user' declared with attribute 'warn_unused_result' [-Werror=unused-result]
1451 | copy_to_user(user_buf, from, bytes);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
4c5beee get rid of VLA on the stack, and fix the resulting error of a too large stack frame
80dda1d Fix LAN->WAN ping failure with over MTU size on outgoing interface
Commit 4c5beee as a side effect fix a compilation warning with
/__w/openwrt/openwrt/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-malta_be/nat46-2022-03-30-95ca1c3b/nat46/modules/nat46-netdev.c: In function 'nat46_remove':
/__w/openwrt/openwrt/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-malta_be/nat46-2022-03-30-95ca1c3b/nat46/modules/nat46-netdev.c:260:9: error: ISO C90 forbids variable length array 'config_remove' [-Werror=vla]
260 | char config_remove[buflen];
| ^~~~
/__w/openwrt/openwrt/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-malta_be/nat46-2022-03-30-95ca1c3b/nat46/modules/nat46-netdev.c:280:17: error: ISO C90 forbids variable length array 'config' [-Werror=vla]
280 | char config[buflen];
| ^~~~
cc1: all warnings being treated as errors
Also this now require nf_defrag_ipv6 as a new dependency.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Kmod-mhi-pci-generic supports Qualcomm modems over PCIe bus. On targets
without PCI support, this package is empty. Symbol CONFIG_MHI_BUS_PCI_GENERIC
depends on CONFIG_PCI.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Kmod-serial-8250-exar supports Serial cards connected via PCIe bus. On targets
without PCI support, this package is empty.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Kmod-i2c-designware-pci supports Synopsys I2C over PCIe bus. On targets
without PCI support, this package is empty. Symbol CONFIG_I2C_DESIGNWARE_PCI
depends on CONFIG_PCI.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Synchronize the ath11k backports with the current ath-next tree.
This replaces the 160MHz with the upstreamed one, fixes 6GHz only WIPHY
registration, allows SAR usage on WCN6750 and plenty of REO fixes.
Signed-off-by: Robert Marko <robimarko@gmail.com>
By default both kmod-bcma and kmod-ssb are selected by kmod-b43.
However, only one of both modules is needed for bmips subtargets:
- bcma: bcm6318, bcm6328, bcm6362, bcm63268
- ssb: bcm6358, bcm6368
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
This adds generic kernel support for Broadcom Fallback SPROMs so that it can be
used in any target, even non Broadcom ones.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
qrtr/ns.ko is now merged into qrtr/qrtr.ko, so drop the individual module packaging.
Fixes: f4989239cc ("kernel: bump 5.15 to 5.15.107")
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de> #ipq807x/ax3600, x86_64/FW-7543B, mt7621/dap-x1860
upstream PR 408 improvements:
-Fix AMSDU packets unused
-Removed the ASMDU packets queue
-Add more info in the iw tool
-fix is_hw_crypto_enabled
-Optimization AMPDU_TX_OPERATIONAL (avoid a spinlock)
change to wongsyrone mod
Signed-off-by: Kabuli Chana <newtownBuild@gmail.com>
QCA has finally sent a proper fixup for the 160MHz regression upstream,
so lets use the pending fix which also properly sets center frequency 2
in case 80+80 MHz is used.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Synchronize the ath11k backports with the current ath-next tree.
This replaces the management TLV pending fix with the upstreamed one,
fixes traffic flooding when AP and monitor modes are used at the same time,
fixes QCN9074 always showing -95 dBm for station RSSI in dumps,
fixes potential crash on boot if spectral scan is enabled due to writing to
unitialized memory and adds 11d scan offloading for WCN6750 and WCN6855.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Currently, during initialization ath11k will receive a regulatory event
from the firmware in which it will receive the default regulatory domain
code and accompanying rules list and report those to the kernel.
Then if you try to change the regulatory domain to a different country code
it will do a weird thing in which it will send that to the FW and after
receiving the appropriate regulatory event it will parse the rules.
However, while its parsing there is a weird thing being done, and that is
that new raw rules from FW get intersected with the rules from the default
domain.
This is creating a big issue as the default domain is almost always set to
"US" or just "00" aka world so ath11k will unfairly limit you to the most
restrictive combination of rules based on the default domain and your
desired domain.
For example, in ETSI countries this is causing channels 12 and 13 on 2.4GHz
to not be usable since "US" limits 2.4GHz to 2472MHz instead of 2482MHz
like ETSI countries do.
So, lets do what TIP and even QCA do in their ath11k downstream tree and
completely get rid of the interesection code in ath11k.
Signed-off-by: Robert Marko <robimarko@gmail.com>
CRYPTO_USER_API_ENABLE_OBSOLETE config symbol depends on CRYPTO_USER so
lets add this dependency to relevant modules.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
While tracking one bug report related to wrong package dependencies I've
noticed, that a bunch of the crypto modules are actually not
architecture specific, but either board/subtarget (x86/64) or board
(mpc85xx) specific.
So lets fix it, by making those modules architecture specific:
x86/64 -> x86_64
mpc85xx -> powerpc
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Kmod-tg3 supports Ethernet adapters over PCIe bus. On targets without
PCI support, this package is empty. Symbol CONFIG_TIGON3 depends on
CONFIG_PCI.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Kmod-hfcpci and kmod-hfcmulti supports ISDN adapters over PCI. On targets
without PCI support, this package is empty. Symbol CONFIG_MISDN_HFCMULTI
and CONFIG_MISDN_HFCPCI depends on CONFIG_PCI.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Recent ath11k sync introduced a regression causing 80+80 and 160MHz to
stop being advertised and thus not selectable due to the respective feature
flags being cleared.
So, until we get answers upstream to what was the reasoning behind this and
it gets fixed, lets just remove the flag clearing to reanable 160MHz.
Fixes: 789a0bac35 ("mac80211: ath11k: sync with ath-next")
Signed-off-by: Robert Marko <robimarko@gmail.com>
When forwarding is set to 0, frames are typically sent with ttl=1.
Move the ttl decrement check below the check for local receive in order to
fix packet drops.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
SSDK is doing everything custom, so trying to use mold and/or LTO
fails, so lets opt-out of using both of them.
Signed-off-by: Robert Marko <robimarko@gmail.com>
[a.heider: split and switch to PKG_BUILD_FLAGS]
Signed-off-by: Andre Heider <a.heider@gmail.com>
Synchronize the ath11k backports with the current ath-next tree.
This brings in actually setting the MU-MIMO parameters in HW and 6GHz
regulatory support along with some minor resource handling fixes.
This allows to easily backport further fixes as cherry picking them has
started requiring manual conflict resolution.
Signed-off-by: Robert Marko <robimarko@gmail.com>
This fixes a build problem on some targets.
Fixes: 3e9005546a ("kernel: modules: package Microchip LAN743x PCIe gigE driver")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
in kernel 5.17, fcd09c90c3c5254b18ef34e30c57c65d34290a84 integrated it
better with thee random framework.
Gives boot time randomness on supported devices.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
The last mac80211 commits did not refresh the patches.
Refresh:
- ath/402-ath_regd_optional.patch
- ath10k/080-ath10k_thermal_config.patch
- ath10k/974-ath10k_add-LED-and-GPIO-controlling-support-for-various-chipsets.patch
- ath9k/551-ath9k_ubnt_uap_plus_hsr.patch
- rt2x00/602-rt2x00-introduce-rt2x00eeprom.patch
Signed-off-by: Nick Hainke <vincent@systemli.org>
This helps bring down rx CPU usage by avoiding calls to the rx handlers in
the slow path. Supports forwarding and local rx, including A-MSDU.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
71d84bfb343e wifi: mt76: mt76x0u: report firmware version through ethtool
99d13130b517 wifi: mt76: support ww power config in dts node
09c614734880 Revert "wifi: mt76: mt7996: rely on mt76_connac2_mac_decode_he_radiotap"
e1c9c1cb50a8 mt76: mt7921: Let PCI core handle power state and use pm_sleep_ptr()
34064dbcd72a wifi: mt76: mt7921e: add pci .shutdown() support
18ccfa73a9e2 wifi: mt76: remove redundent MCU_UNI_CMD_* definitions
282845ce7f3d wifi: mt76: mt7921: fix wrong command to set STA channel
546934dacfd4 wifi: mt76: mt7921: fix PCI DMA hang after reboot
fc2ed0dfc5b0 wifi: mt76: mt7996: Remove unneeded semicolon
1b602db9c235 wifi: mt76: mt7915: unlock on error in mt7915_thermal_temp_store()
ce2438aa616a wifi: mt76: mt7996: fix radiotap bitfield
17ec2146b8f0 wifi: mt76: dynamic channel bandwidth changes in AP mode
ab2d3650a456 wifi: mt76: mt7915: expose device tree match table
90d78253498e wifi: mt76: mt7915: add dev->hif2 support for mt7916 WED device
a69c34a60451 wifi: mt76: mt7915: rework init flow in mt7915_thermal_init()
39079b5e44a7 wifi: mt76: drop the incorrect scatter and gather frame
f9ca70d6367a wifi: mt76: mt7915: add back 160MHz channel width support for MT7915
eff7666e1aa4 wifi: mt76: handle failure of vzalloc in mt7615_coredump_work
920bc6e1fc8e wifi: mt76: do not run mt76_unregister_device() on unregistered hw
b0721b96927b wifi: mt76: connac: refresh tx session timer for WED device
c32d6d849c43 wifi: mt76: usb: fix use-after-free in mt76u_free_rx_queue
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Fix hwmon-gsc driver by replacing out-of-tree hwmon-gsc driver with in-tree
driver that was merged in Linux v5.8:
- remove the old out-of-tree module
- add configuration for the in-tree modules
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
If a packet has reached its intended destination, it was bumped to the code
that accepts it, without first checking if a mesh_path needs to be created
based on the discovered source.
Fix this by moving the destination address check further down
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Synchronize the ath11k backports with the current ath-next tree.
This backports several memory leak issues, PCI IRQ fixup, peer add locking
fix as well as IPQ5018 support, though IPQ5018 support is unused for now.
This allows to easily backport further fixes as cherry picking them has
started requiring manual conflict resolution.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Pstore ramoops support is useful even when there isn't an explicit
panic/crash. We can log all kernel messages via a "console", and then
retrieve them in the event of some non-kernel-panic reset (e.g.,
watchdog).
Since the buffer memory is already reserved, there isn't much overhead
to doing this.
The new console files will show up as:
/sys/fs/pstore/console-ramoops-N
Cc: Hannu Nyman <hannu.nyman@iki.fi>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Package the Aquantia AQR PHY driver as kmod.
This enables using the Aquantia driver with hwmon support on targets where
hwmon is not compiled-in.
Currently, in case when AQR driver is compiled-in but hwmon core is not
hwmon code in AQR driver will not get compiled because of macro
IS_REACHABLE(CONFIG_HWMON) evaluating to false.
Signed-off-by: Robert Marko <robimarko@gmail.com>
The standard defines the A-MSDU header length field differently for mesh
compared to other modes. Deal with this accordingly and work around broken
implementations (e.g. ath10k, ath11k).
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The upstream value read from the device seems to already be in bits per
second, so there is no need to multiply by 1000 again (which for typical
values causes an overflow of the 32-bit unsigned integer).
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
"842" is a compression scheme and this is the software implementation
which is too slow to really use beyond a proof of concept. It can be
selected in ZRAM, ZSWAP, or `fs/pstore`, and is here for completeness.
In general you need a Power8 or better with 842-in-hardware for it to
be fast, but other 842-accelerators are emerging.
Signed-off-by: Tony Butler <spudz76@gmail.com>
This adds missing HE modes to mac80211_prepare_ht_modes.
Previously mesh without wpa_supplicant would be initialized with 802.11g
/NO-HT only, as this method did not parse channel bandwidth for HE
operation.
Signed-off-by: David Bauer <mail@david-bauer.net>
This uses version 4.23.1 of the drv_dsl_cpe_api package from the Intel
UGW 8.5.2.10 for the VRX518.
Signed-off-by: Martin Schiller <ms.3headeddevs@gmail.com>
[rebased and updated for kernel 5.10]
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
[update to 4.23.1, switch to tag tarball, update patches]
Signed-off-by: Andre Heider <a.heider@gmail.com>
[added fix for elapsed time and upstream MINEFTR]
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Signed-off-by: Andre Heider <a.heider@gmail.com>
This uses version 1.11.1 of the drv_mei_cpe package from the Intel UGW
8.5.2.10 for the VRX518.
Signed-off-by: Martin Schiller <ms.3headeddevs@gmail.com>
[updated for kernel 5.10]
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
[update to 1.11.1, switch to tag tarball, update patches]
Signed-off-by: Andre Heider <a.heider@gmail.com>
[update for kernel 5.15]
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Signed-off-by: Andre Heider <a.heider@gmail.com>
This driver version is also included in Intel UGW 8.5.2.10.
Signed-off-by: Martin Schiller <ms.3headeddevs@gmail.com>
[updated for kernel 5.10]
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
[update to 1.5.12.4, switch to tag tarball]
Signed-off-by: Andre Heider <a.heider@gmail.com>
[add working software data path]
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Signed-off-by: Andre Heider <a.heider@gmail.com>
This driver was picked from the Intel UGW 8.5.2.
Signed-off-by: Martin Schiller <ms.3headeddevs@gmail.com>
[updated for kernel 5.10]
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
[update to 8.5.2]
Signed-off-by: Andre Heider <a.heider@gmail.com>
[fix masking interrupts and add locking]
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Signed-off-by: Andre Heider <a.heider@gmail.com>
Qualcomm NSS-DP is as its name says Qualcomms ethernet driver for the NSS
subsystem (Networking subsystem) built-into various Qualcomm SoCs.
It has 2 modes of operation:
* Without NSS FW and rest of code required for offloading
This is the one that we will use as the amount of kernel patching required
for NSS offloading and the fact that its not upstreamable at all makes it
unusable for us.
Driver in this mode is rather basic, it currently only offers NAPI GRO
(Added by us as part of the fixup) and basically relies on the powerfull
CPU to get good throughput.
* With NSS FW and rest of code required for offloading
In this mode, driver just registers the interfaces and hooks them into
NSS-ECM to allow offloading.
This mode is not viable for use in OpenWrt due to reasons already described
above.
This driver is required for ipq807x to have wired networking until a better
one is available, so lets add the fixed-up version for 5.15 for now.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Qualcomm SSDK is driver for Qualcomm Atheros switches and PHY-s.
It is quite complicated and used by rest of the Qualcomm SDK stack for
anything switch or PHY related.
It is required for IPQ807x support as currently, there is no better driver
for the built-in switch or UNIPHY.
So, lets add the fixed-up version that supports kernel 5.15 for use on
ipq807x target until a better driver is available.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Signed-off-by: Robert Marko <robimarko@gmail.com>
This is the follow up to the PCI support commit now providing support for
AHB variant as well, though currently only for ipq807x as that is only
OpenWrt supported SoC ath11k supports as well.
Currently, we are disabling coldboot calibration on ipq807x as it does not
work, there is a remoteproc bug that makes it come late out of reset so
disable coldboot until that is fixed.
Also, as ath11k is quite memory hungry, we are introducing a config option
to use the limits for 512MB of RAM, similar to what QCA does downstream but
in way simpler and cleaner way so that 512MB save some RAM.
512MB profile is also set as the default for now.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Qualcomm Atheros IPQ807x is a modern WiSoC featuring:
* Quad Core ARMv8 Cortex A-53
* @ 2.2 GHz (IPQ8072A/4A/6A/8A) Codename Hawkeye
* @ 1.4 GHz (IPQ8070A/1A) Codename Acorn
* Dual Band simultaneaous IEEE 802.11ax
* 5G: 8x8/80 or 4x4/160MHz (IPQ8074A/8A)
* 5G: 4x4/80 or 2x2/160MHz (IPQ8071A/2A/6A)
* 5G: 2x2/80MHz (IPQ8070A)
* 2G: 4x4/40MHz (IPQ8072A/4A/6A/8A)
* 2G: 2x2/40MHz (IPQ8070A/1A)
* 1x PSGMII via QCA8072/5 (Max 5x 1GbE ports)
* 2x SGMII/USXGMII (1/2.5/5/10 GbE) on Hawkeye
* 2x SGMII/USXGMII (1/2.5/5 GbE) on Acorn
* DDR3L/4 32/16 bit up to 2400MT/s
* SDIO 3.0/SD card 3.0/eMMC 5.1
* Dual USB 3.0
* One PCIe Gen2.1 and one PCIe Gen3.0 port (Single lane)
* Parallel NAND (ONFI)/LCD
* 6x QUP BLSP SPI/I2C/UART
* I2S, PCM, and TDMA
* HW PWM
* 1.8V configurable GPIO
* Companion PMP8074 PMIC via SPMI (GPIOS, RTC etc)
Note that only v2 SOC models aka the ones ending with A suffix are
supported, v1 models do not comply to the final 802.11ax and have
lower clocks, lack the Gen3 PCIe etc.
SoC itself has two UBI32 cores for the NSS offloading system, however
currently no offloading is supported.
Signed-off-by: Robert Marko <robimarko@gmail.com>
This is a temporary workaround for supporting multiple cards or AHB+PCI.
There is ongoing upstream work to properly support this based of
advertised FW features, but that is still ongoing.
This is only supported on QCN9074 cards due to FW limitation, so HW ID
is checked in order to prevent breaking QCA6390 and other popular cards.
Signed-off-by: Robert Marko <robimarko@gmail.com>
SOC: Qualcomm IPQ4019
WiFi 1: QCA4019 IEEE 802.11b/g/n
WiFi 2: QCA4019 IEEE 802.11a/n/ac
WiFi 3: QCA8888 IEEE 802.11a/n/ac
Bluetooth: Qualcomm CSR8811 (A12U)
Zigbee: Silicon Labs EM3581 NCP + Skyworks SE2432L
Ethernet: Qualcomm Atheros QCA8072 (2-port)
Flash 1: Mactronix MX30LF4G18AC-XKI
RAM (NAND): SK hynix H5TC4G63CFR-PBA (512MB)
LED Controller: NXP PCA9633 (I2C)
Buttons: Single reset button (GPIO).
- The three WiFis were fully tested and are configured with the same settings as in the vendor firmware.
- The specific board files were submitted to the ATH10k mailing list but I'm still waiting for a reply. They can be removed once they are approved upstream.
- Two ethernet ports are accessible on the device. By default one is configured as WAN and the other one is LAN. They are fully working.
Bluetooth:
========
- Fully working with the following caveats:
- RFKILL need to be enabled in the kernel.
- An older version of bluez is needed as bccmd is needed to configure the chip.
Zigbee:
======
- The spidev device is available in the /dev directory.
- GPIOs are configured the same way as in the vendor firmware.
- Tests are on-going. I am working on getting access to the Silicon Labs stack to validate that it is fully working.
Installation:
=========
The squash-factory image can be installed via the Linksys Web UI:
1. Open "http://192.168.1.1/ca" (Change the IP with the IP of your device).
2. Login with your admin password.
3. To enter into the support mode, click on the "CA" link and the bottom of the page.
4. Open the "Connectivity" menu and upload the squash-factory image with the "Choose file" button.
5. Click start. Ignore all the prompts and warnings by click "yes" in all the popups.
The device uses a dual partition mechanism. The device automatically revert to the previous partition after 3 failed boot attempts.
If you want to force the previous firmware to load, you can turn off and then turn on the device for 2 seconds, 3 times in a row.
It can also be done via TFTP:
1. Setup a local TFTP server and configure its IP to 192.168.1.100.
2. Rename your image to "nodes_v2.img" and put it to the TFTP root of your server.
3. Connect to the device through the serial console.
4. Power on device and press enter when prompted to drop into U-Boot.
5. Flash the partition of your choice by typing "run flashimg" or "run flashimg2".
6. Once flashed, enter "reset" to reboot the device.
Reviewed-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Vincent Tremblay <vincent@vtremblay.dev>
Currently, ath11k will crash the crash if we try to bringup the monitor
mode interface.
Luckily, it has already been fixed upstream, so backport the patches
fixing it.
Fixes: 93ae4353cd ("mac80211: add ath11k PCI support")
Signed-off-by: Robert Marko <robimarko@gmail.com>
This fixes a security problem in ksmbd. It currently has the
ZDI-CAN-18259 ID assigned, but no CVE yet.
Backported from:
8824b7af40cc4f3b5a6a
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
GCC 12.2.0 shows these error messages:
````
rtl8812au-ct-2021-11-07-39df5596/core/rtw_sta_mgt.c: In function 'rtw_mfree_stainfo':
rtl8812au-ct-2021-11-07-39df5596/core/rtw_sta_mgt.c:210:24: error: the comparison will always evaluate as 'true' for the address of 'lock' will never be NULL [-Werror=address]
210 | if(&psta->lock != NULL)
| ^~
In file included from rtl8812au-ct-2021-11-07-39df5596/include/drv_types.h:109,
from rtl8812au-ct-2021-11-07-39df5596/core/rtw_sta_mgt.c:22:
rtl8812au-ct-2021-11-07-39df5596/include/sta_info.h:95:17: note: 'lock' declared here
95 | _lock lock;
| ^~~~
````
````
CC [M] rtl8812au-ct-2021-11-07-39df5596/os_dep/linux/ioctl_cfg80211.o
rtl8812au-ct-2021-11-07-39df5596/os_dep/linux/ioctl_cfg80211.c: In function 'cfg80211_rtw_scan':
rtl8812au-ct-2021-11-07-39df5596/os_dep/linux/ioctl_cfg80211.c:2176:32: warning: the comparison will always evaluate as 'true' for the address of 'ssid' will never be NULL [-Waddress]
2176 | if(ssids->ssid != NULL
| ^~
In file included from rtl8812au-ct-2021-11-07-39df5596/include/osdep_service_linux.h:88,
from rtl8812au-ct-2021-11-07-39df5596/include/osdep_service.h:41,
from rtl8812au-ct-2021-11-07-39df5596/include/drv_types.h:32,
from rtl8812au-ct-2021-11-07-39df5596/os_dep/linux/ioctl_cfg80211.c:22:
/home/hauke/openwrt/openwrt/staging_dir/target-mips_24kc_musl/usr/include/mac80211/net/cfg80211.h:2364:12: note: 'ssid' declared here
2364 | u8 ssid[IEEE80211_MAX_SSID_LEN];
| ^~~~
````
````
CC [M] rtl8812au-ct-2021-11-07-39df5596/hal/OUTSRC/phydm_debug.o
rtl8812au-ct-2021-11-07-39df5596/hal/OUTSRC/phydm_debug.c: In function 'phydm_cmd_parser':
rtl8812au-ct-2021-11-07-39df5596/hal/OUTSRC/phydm_debug.c:873:28: warning: the comparison will always evaluate as 'true' for the pointer operand in 'input + ((sizetype)i + 1) * 16' must not be NULL [-Waddress]
873 | if(input[i+1]) {
| ^~~~~
rtl8812au-ct-2021-11-07-39df5596/hal/OUTSRC/phydm_debug.c:894:28: warning: the comparison will always evaluate as 'true' for the pointer operand in 'input + ((sizetype)i + 1) * 16' must not be NULL [-Waddress]
894 | if(input[i+1]) {
| ^~~~~
````
This one was only seen on the rockchip/armv8 target:
````
CC [M] rtl8812au-ct-2021-11-07-39df5596/core/rtw_br_ext.o
In function '__nat25_add_pppoe_tag',
inlined from 'nat25_db_handle' at rtl8812au-ct-2021-11-07-39df5596/core/rtw_br_ext.c:909:10:
rtl8812au-ct-2021-11-07-39df5596/core/rtw_br_ext.c:118:9: error: 'memcpy' reading between 2052 and 9220 bytes from a region of size 40 [-Werror=stringop-overread]
118 | memcpy((unsigned char *)ph->tag, tag, data_len);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
rtl8812au-ct-2021-11-07-39df5596/core/rtw_br_ext.c: In function 'nat25_db_handle':
rtl8812au-ct-2021-11-07-39df5596/core/rtw_br_ext.c:878:63: note: source object 'tag_buf' of size 40
878 | unsigned char tag_buf[40];
| ^~~~~~~
````
Most of them are looking like real errors to me, but some fixes need a
deeper understanding of the driver and probably bigger changes to the driver.
Ignore these error messages for now. It would be nice if someone would
fix them.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add a separate firmware package to avoid installing the MT7615 firmware
on all MT7622 target devices by default. Now we only add MT7615 firmware
packages for devices that use MT7615E. This commit also removes the
explicit dependency on kmod-mt7615e to refine the package dependency.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
The mt7915e driver supports MT7915, MT7916 and MT7986 chips. And Only
MT7915 series chips need the MT7915 firmware. To save storage, extract
them from the common code package and create a new package to provide
the firmware.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
The kmod-mt7615-common package does not contain any code that
related to mt7915e Wi-Fi6 driver, so remove it.
Tested on ramips/mt7621: SIM SIMAX1800T
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
brcmsmac needs bcma. bcma is build into the kernel for the other bcm47xx
subtargets, but not for the legacy target because it only uses ssb. We
could build bcma as a module for bcm47xx_legacy, but none of these old
devices uses a wifi card supported by brcsmac.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
ath11k is the upstream driver for Qualcomm 802.11ax radios, both for the
internal AHB and PCI based cards.
This commit does however only provide PCI support while AHB will follow
but its SoC specific so it will require an OpenWrt target first.
It differs a bit from ath10k as it requires stuff like QRTR, MHI and QMI
helpers.
PCI variant requires qrtr-mhi and mhi-bus which backports do provide,
however we are dropping those in a patch as they will conflict with
support for the AHB variant as that one requires qrtr-smd which in turn
requires RPMSG and GLINK and its not feasable to provide those in
backports as they are really SoC specific.
QRTR and MHI in kernel 5.10 are not usable and backporting the changes
is not easy as they have changed drastically from 5.10 to 5.15 ath11k will
only be available on targets that use kernel 5.15.
Signed-off-by: Robert Marko <robimarko@gmail.com>
QRTR is Qualcomm IPC router protocol and ath11k requires it for both
AHB and PCI support, so package it as a kernel module so it can be
added as a dependency to the ath11k module.
Only kernel 5.15 is currently supported due to various things missing in
5.10 whose backporting is out of scope for this patch.
SMD, TUN and MHI variants are packaged.
SMD variant depends on the ipq807x
target as it has dependency on the RPMSG drivers which are Qualcomm
and SoC specific anyway.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Make use of KERNEL_MAKE in kernel packages were easily possible.
This moves some more code to common places and reduces the number of
lines.
It is defined like this:
KERNEL_MAKE = $(MAKE) $(KERNEL_MAKEOPTS)
KERNEL_MAKEOPTS = -C $(LINUX_DIR) $(KERNEL_MAKE_FLAGS)
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Two WS2812B (NeoPixel) clones are used in Xiaomi Redmi AX6000 as
indicator lights. Add a driver for controlling it using SPI MOSI.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
When reloading modules and running wifi, a phy can sometimes be renamed
while in the middle of a hotplug call that tries to detect new phys
This can lead to bogus wifi-device sections being created
Signed-off-by: Felix Fietkau <nbd@nbd.name>
hostapd's compile time option CONFIG_IEEE80211N was removed almost 3 years
ago, 80.211n/HT is always included since then.
Noticed because `hostapd -v11n` confusingly returned an error.
See hostapd's commit:
f3bcd69603 "Remove CONFIG_IEEE80211N build option"
Signed-off-by: Andre Heider <a.heider@gmail.com>
enable option `CONFIG_CRYPTO_LZ4HC` to match default kernel config
this only adds the `lz4hc_compress` module, and has no effect on the
`lz4_decompress` module which already supports any flavor
Signed-off-by: Tony Butler <spudz76@gmail.com>
With this patch you can change the pulse digit time by loading the Lantiq
FXS driver kernel module called ltq-tapi. This is relevant for old
rotaryphones that uses pulsedialing.
The default values are:
30-80ms for the low pulse
30-80ms for the high pulse
300ms for minimum Interdigit time
this is OK but on some Phones it can be usefull to customize the values
If you want to change the values to high and low pulse to 40-90ms and
minimum interdigit time to 400ms
than change /etc/modules.d/20-ltq-tapi to (without linebrakes):
drv_tapi min_digit_low=40 min_digit_high=90 max_digit_low=40 \
max_digit_high=90 min_interdigit=400
Signed-off-by: Jonas Albrecht <plonkbong100@protonmail.com>
Some copper SFP modules come with Marvell's 88E1xxx PHY and need this
module to function. Package it, so users can easily install this PHY
driver and use e.g. FINISAR CORP. FCLF-8521-3-HC SFP.
Without marvell PHY driver:
sfp sfp2: module FINISAR CORP. FCLF-8521-3-HC rev A sn XXXXXXX dc XXXXXX
mt7530 mdio-bus:1f sfp2: validation with support 0000000,00000000,00000000 failed: -22
sfp sfp2: sfp_add_phy failed: -22
With marvell PHY driver:
sfp sfp2: module FINISAR CORP. FCLF-8521-3-HC rev A sn XXXXXXX dc XXXXXX
mt7530 mdio-bus:1f sfp2: switched to inband/sgmii link mode
mt7530 mdio-bus:1f sfp2: PHY [i2c:sfp2:16] driver [Marvell 88E1111] (irq=POLL)
mt7530 mdio-bus:1f sfp2: Link is Up - 1Gbps/Full - flow control rx/tx
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
It's not just required for the PCI version, but for USB and presumably
SDIO as well.
Tested with 0e8d:7961 Comfast CF-953AX (MT7921AU).
Signed-off-by: Andre Heider <a.heider@gmail.com>
USB adaptors with the RTL8761B chipset are cheap and readily available
but so far support is missing in Openwrt. Enable the relevant kernel
options and add a module to the kmod-bluetooth package. Increases size
of kmod-bluetooth ipk from 279140 bytes to 285320 bytes on my ath79 build.
Tested on a WNDR3700v4 with rtl8761bu firmware.
Signed-off-by: Quintin Hill <stuff@quintin.me.uk>
Get rid of drivers that are either limited to 802.11b/g or don't even support
cfg80211/mac80211. Most of these are either limited to boards that we don't even
support anymore because of firmware size, or were only used for custom hacks by
a really small number of users in the past.
Let's get rid of those to reduce the maintenance effort and the number of useless
packages
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add kernel package 'mt7916-firmware' with firmware files for MT7916E devices.
These share the same driver as the MT7915 chipset, but use their own firmware.
Tested using a pair of AsiaRF AW7916-NPD cards.
Signed-off-by: Andrew Powers-Holmes <aholmes@omnom.net>
Do not use find_vpid(), but get_task_pid() to get the pid from
pThrCntrl->tid. This is now a ponter to struct task_struct instead of
an integer.
This fixes the build of ltq-tapi with lantiq/xway.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Do not include asm/irq.h directly, but include linux/interrupt.h instead.
This fixes the build of ltq-tapi with lantiq/xway.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
In my commit da5c45f4d8 ("kernel: remove handling of xfrm[4|6]_mode_*
modules") I missed a few default config options and description entries.
Those should be gone as well.
Fixes: da5c45f4d8 ("kernel: remove handling of xfrm[4|6]_mode_* modules")
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Add a package for drm_ttm_helper.ko. CONFIG_DRM_TTM_HELPER is compiled
into the kernel on armvirt/64, x86/64, x86/generic and x86/legacy
because also some DRM drivers are compiled into the kernel. On x86/geode
it is not compiled into the kernel, but kmod-drm-amdgpu and
kmod-drm-radeon depend on it.
This fixes the x86/geode build.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
For kernel versions before 5.2, the required IPsec modes have to be
enabled explicitly (they are built-in for newer kernels).
Commit 1556ed155a ("kernel: mode_beet mode_transport mode_tunnel xfram
modules") tried to handle this, but it does not really work.
Since we don't support these kernel versions anymore and the code is
also broken, let's remove it.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
[Remove old generic config options too]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The kernel module gpio-mcp23s08 has been replaced by the new
pinctrl-mcp23s08* kernel modules.
There are now 3 kernel modules for this device
- Common module for both I2C and SPI kmod-pinctrl-mcp23s08
- Module for I2C kmod-pinctrl-mcp23s08-i2c
- Module for SPI kmod-pinctrl-mcp23s08-spi
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
CONFIG_MAC80211_MESH isn't defined for this package, rendering the patch
useless. Match protecting the access of sta_info.mesh with the very same
define declaring it.
Fixes 45109f69a6 "mac80211: fix compile error when mesh is disabled"
Signed-off-by: Andre Heider <a.heider@gmail.com>
This updates mac80211 to version 5.15.74-1 which is based on kernel
5.15.74.
The removed patches were applied upstream.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
struct of_device_id is not implicitly included anymore. Include
<linux/mod_devicetable.h> to fix compilation on Linux 5.15.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
MODULE_SUPPORTED_DEVICE is gone after Linux 5.15. Drop it's usage on
newer kernels to fix compilation with Linux 5.15.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
The result of copy_to_user() now has to be checked explicitly. Also
MODULE_SUPPORTED_DEVICE is gone after Linux 5.10.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
MODULE_SUPPORTED_DEVICE was removed after Linux 5.10. Drop it from the
driver as well.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
struct of_device_id is not implicitly included anymore. Include
<linux/mod_devicetable.h> to fix compilation on Linux 5.15.
Also upstream commit a24d22b225ce15 ("crypto: sha - split sha.h into
sha1.h and sha2.h") from Linux 5.11 moves functionality from sha.h to
sha1.h.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
set_fs is no longer supported since kernel 5.13 for mips.
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
The of_mmc_spi.o resource is provider agnostic in kernels greater 5.13
and does not depend anymore on CONFIG_OF [0].
[0] - edd6021465
Suggested-by: John Thomson <git@johnthomson.fastmail.com.au>
Signed-off-by: Nick Hainke <vincent@systemli.org>
This new NTFS driver was added in kernel 5.15. Avoid building empty
package for kernel 5.10.
Fixes: bd0db6017b ("kernel: 5.15: add new module")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Replace the extern inline with a static inline. With extern inline the
compiler will generate the function in all compile units including this
file which breaks linking later.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This makes it clear, which phy a wlan device belongs to and also helps with
telling them apart by including the mode in the ifname.
Preparation for automatically renaming PHYs
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Reported-by: Chad Monroe <chad.monroe@smartrg.com>
Fixes: 590eaaeed5 ("mac80211: fix issues in HE capabilities")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This mainly affects scanning and beacon parsing, especially with MBSSID enabled
Fixes: CVE-2022-41674
Fixes: CVE-2022-42719
Fixes: CVE-2022-42720
Fixes: CVE-2022-42721
Fixes: CVE-2022-42722
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Enable HE SU beamformee by default
Fix spatial reuse configuration:
- he_spr_sr_control is not a bool for enabling, it contains multiple bits
which disable features that should be disabled by default
- one of the features (PSR) can be enabled through he_spr_psr_enabled
- add option to disable bss color / spatial reuse
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This fixes following compile error seen when
building mac80211 with mesh disabled:
.../backports-5.15.58-1/net/mac80211/agg-rx.c: In function 'ieee80211_send_addba_resp':
...backports-5.15.58-1/net/mac80211/agg-rx.c:255:17: error: 'struct sta_info' has no member named 'mesh'
255 | if (!sta->mesh)
| ^~
sta_info.h shows this item as being optional based on flags:
struct mesh_sta *mesh;
Guard the check to fix this.
Fixes: f96744ba6b ("mac80211: mask nested A-MSDU support for mesh")
Signed-off-by: Koen Vandeputte <koen.vandeputte@citymesh.com>
mac80211 incorrectly processes A-MSDUs contained in A-MPDU frames. This
results in dropped packets and severely impacted throughput.
As a workaround, don't indicate support for A-MSDUs contained in
A-MPDUs. This improves throughput over mesh links by factor 10.
Ref: https://github.com/openwrt/mt76/issues/450
Signed-off-by: David Bauer <mail@david-bauer.net>
As also ramips/mt7621 now has a user of the ubnt-ledbar driver, make
the package available on all targets by removing the dependency on
@TARGET_mediatek_mt7622.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This reverts commit 6e9613844c.
The patch was wrong in the first place as we base everything on
backports package and the compilation error was caused by an ath11k
present downstream. (will be needed later when backports package will be
updated but not now)
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
With kernel 5.15.61 the define IEEE80211_MAX_AMPDU_BUF got changed to
IEEE80211_MAX_AMPDU_BUF_HE. Add patch to fix compilation error on next
5.15 kernel versions.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
The "tx_burst" option which should control the value was
expecting more of a list and hence tx_queue_data2_burst
value wasn't updated.
Yes, it would make sense to have a list for this, the
existing code only updates tx_queue_data2_burst and
not the other tx_queue_data[0134]_burst values.
Signed-off-by: Alberto Martinez-Alvarez <amteza@gmail.com>
(formatted commit message, wrote extra information into commit,
moved tx_burst to existing json_get_vars)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Prevents build errors by ensuring that it is only selected when a wext based
driver that needs it is also selected
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This package downloads raw files
which have names that are not corresponding to
the name and version of the package
as it is defined in the Makefile.
Use the option DL_SUBDIR to set the DL_DIR
to be a subdirectory named with
PKG_NAME and PKG_SOURCE_DATE
to better organize the downloads.
Define PKG_VERSION here
using PKG_SOURCE_DATE.
Signed-off-by: Michael Pratt <mcpratt@pm.me>
This matches the scheme used by other target packages and will avoid
confusion with any future version.
Signed-off-by: Andre Heider <a.heider@gmail.com>
Instead of always including the XHCI driver in the kernel on all
MediaTek boards, selectively include the kernel module only on boards
which actually make use of USB functionality.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
add Flow Queuing with Proportional Integral controller Enhanced (FQ-PIE) as an
optional kmod in network support and extract sched-pie from kmod-sched to
allow dependency on just kmod-sched-pie (PIE).
Signed-off-by: Kabuli Chana <newtownBuild@gmail.com>
Serge Vasilugin reports:
To improve mt7620 built-in wifi performance some changes:
1. Correct BW20/BW40 switching (see comments with mark (1))
2. Correct TX_SW_CFG1 MAC reg from v3 of vendor driver see
https://gitlab.com/dm38/padavan-ng/-/blob/master/trunk/proprietary/rt_wifi/rtpci/3.0.X.X/mt76x2/chips/rt6352.c#L531
3. Set bbp66 for all chains.
4. US_CYC_CNT init based on Programming guide, default value was 33 (pci),
set chipset bus clock with fallback to cpu clock/3.
5. Don't overwrite default values for mt7620.
6. Correct some typos.
7. Add support for external LNA:
a) RF and BBP regs never be corrected for this mode
b) eLNA is driven the same way as ePA with mt7620's pin PA
but vendor driver explicitly pin PA to gpio mode (for forrect calibration?)
so I'm not sure that request for pa_pin in dts-file will be enough
First 5 changes (really 2) improve performance for boards w/o eLNA/ePA.
Changes 7 add support for eLNA
Configuration w/o eLAN/ePA and with eLNA show results
tx/rx (from router point of view) for each stream:
35-40/30-35 Mbps for HT20
65-70/60-65 Mbps for HT40
Yes. Max results for 2T2R client is 140-145/135-140
with peaks 160/150, It correspond to mediatek driver results.
Boards with ePA untested.
Reported-by: Serge Vasilugin <vasilugin@yandex.ru>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Prepare patches for sending upstream by adding patch descriptions
generated from the original OpenWrt commits adding each patch.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Enable MediaTek protocol in btusb module to support e.g. the Bluetooth
part of the MT7921K NGFF/M.2 module.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Devices using GPT usually have FAT filesystem on boot partition and
that's where the intermediary backup of system configuration is stored
on sysupgrade. Automatic restoring of OpenWrt configuration after
sysupgrade will be inhibited if the driver is not loaded and file system
type is not specified in mount command.
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Older MT7623 ARMv7 SoC as well as new Filogic platforms come with
inside-secure,safexcel-eip97 units. Enable them in DTS and select the
driver kernel module by default on those platforms.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
It is common for 802.11ax NICs to support more than just AP mode, which
results in there being a distinct set of HE capabilities for each mode. As
(bad) luck would have it, iw prints out info for each HE mode in sequential
order according to `enum nl80211_iftype`, and AP mode isn't always first.
As a result, the wrong set of HE capabilities can be parsed if an AP NIC
supports station (managed) mode or any other mode preceding AP mode, since
only the first set of HE capabilities printed by iw is parsed from awk's
output.
This has a noticeable impact on beamforming for example, since managed mode
usually doesn't have beamformer capabilities enabled, while AP mode does.
Hostapd won't be set up with the configs to enable beamformer capabilities
in this scenario, causing hostapd to disable beamforming to HE stations
even when it's supported by the AP.
Always parse the correct set of HE capabilities for AP mode to fix this.
This is achieved by trimming all of iw's output prior to the AP mode
capabilities, which ensures that the first set of HE capabilities are
always for AP mode.
Signed-off-by: Sultan Alsawaf <sultan@kerneltoast.com>
There is only one module in kmod-sched that depends on iptables. Move it
to its own kmod package so we can drop the kmod-ipt-core dependency from
kmod-sched. This makes it possible to disable all kmod-ipt-* packages
without having to disable kmod-sched. Since we now default to firewall4
and nftables, we should avoid iptables dependencies where we can.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
This fixes the following build error:
Package kmod-hwmon-tps23861 is missing dependencies for the following libraries:
regmap-i2c.ko
Fixes: b664646db7 ("kernel: add kmod-hwmon-tps23861 support")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
While kmod-input-core was previously indirectly selected by
kmod-input-polldev, this is now only the case on Linux 5.10.
Select kmod-input-core as dependency independently of the kernel
version to fix build error:
Package kmod-input-gpio-keys-polled is missing dependencies for the following libraries:
input-core.ko
Fixes: 54878fbbdd ("kernel: kmod-input-polldev: Depend on kernel 5.10")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add support for randomly generating a MAC address for a wifi-iface
instance by setting `macaddr` to `random`
When set to `random`, a new locally administered unicast MAC address
is generated and assigned to the iface everytime it is (re-)configured
Signed-off-by: Manas Sambhus <manas.sambhus+github@gmail.com>
The input-polldev.ko kernel module was removed from kernel 5.11. The
normal input implementation now supports polling.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The sps30.ko driver was split into a main sps30.ko driver and a
sps30_i2c.ko driver for the I2C interface with kernel 5.14. Add the
sps30_i2c.ko module to the package too.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The isdn4linux drivers and subsystem was removed in kernel 5.3, remove
the kernel package also from OpenWrt.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The rtc-pt7c4338.ko was never upstream under this name, the driver was
removed from OpenWrt some years ago, remove the kmod-rtc-pt7c4338
package too.
Fixes: 74d00a8c38 ("kernel: split patches folder up into backport, pending and hack folders")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This adds the kmod-wwan package. This provides the generic wwan driver
core which is needed for some existing packages.
Currently the drivers/net/wwan/wwan.ko driver is compiled into the
kernel when one of the wwan module is activated, better build it as a
kernel module.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The ulog iptables target was removed with kernel 3.17, remove the kernel
and also the iptables package in OpenWrt too.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The nft NAT packages for IPv4 and IPv6 were merged into the common
packages with kernel 5.1. The kmod-nft-nat6 package was empty in our
build, remove it.
Multiple kernel configuration options were also removed, remove them
from our generic kernel configuration too.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The w1_ds2760.ko driver was merged into the ds2760_battery.ko driver.
The driver was removed and this package was never build any more.
This happened with kernel 4.19.
Remove this unused package.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The R8712U driver depends on cfg80211. cfg80211 is provided by mac80211
backports, we can not build any in kernel drivers which depend on
cfg80211 which is an out of tree module in OpenWrt.
The cfg80211 dependency was added with kernel 5.9.
We could add rtl8192su to backports and build it from there.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The malta target does not compile CONFIG_OF_MDIO into the kernel. On
malta the kmod-mdio-devres package depends on kmod-of-mdio.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The CONFIG_CACHEFILES configuration option makes the kernel build
cachefiles.ko, also package it. Build CONFIG_CACHEFILES as module and do
not try to build it into the kernel. This did not work because it
depended on CONFIG_FSCACHE which was already build as module.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The CONFIG_NLS_CODEPAGE_932 Config option builds the nls_cp932.ko and
the nls_euc-jp.ko kernel module, package both of them.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add dwc2_pci kernel module into own kernel package.
The dwc2_pci.ko kernel module was always build when kmod-usb-dwc2
was selected, but it was not packaged.
Add the missing kmod-usb-phy-nop dependency to the kmod-usb-dwc2-pci
package too. The CONFIG_USB_DWC2_PLATFORM option is already gone for
some time.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The ar8xxx.ko kernel module uses the devm_mdiobus_alloc() function
provided by kmod-mdio-devres, add the missing dependency.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Both of these packages depend on CONFIG_WWAN
in the kernel.
Also fix the missing "wwan" subfolder in the path.
This fixes the missing devices in /dev after booting an MHI capable modem.
Fixes: 2519190fec ("kernel: package mhi wwan ctrl driver")
Fixes: 6af46796fa ("kernel: package mhi mbim driver")
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Backports upstream fix from 5.19
lockdep complains use of uninitialized spinlock at ieee80211_do_stop() [1],
for commit f856373e2f31ffd3 ("wifi: mac80211: do not wake queues on a vif
that is being stopped") guards clear_bit() using fq.lock even before
fq_init() from ieee80211_txq_setup_flows() initializes this spinlock.
According to discussion [2], Toke was not happy with expanding usage of
fq.lock. Since __ieee80211_wake_txqs() is called under RCU read lock, we
can instead use synchronize_rcu() for flushing ieee80211_wake_txqs().
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
This extracts kmod-sched-act-police to allow using it without adding all
the packages from the big kmod-sched package.
Signed-off-by: Hauke Mehrtens <hmehrtens@maxlinear.com>
Add the ipset/ip_set_hash_ipmac.ko file. The CONFIG_IP_SET_HASH_IPMAC
KConfig option is already set by the package.
Signed-off-by: Hauke Mehrtens <hmehrtens@maxlinear.com>
This adds the act_sample.ko and psample.ko kernel module which allows
traffic sampling.
Signed-off-by: Thomas Langer <tlanger@maxlinear.com>
Signed-off-by: Hauke Mehrtens <hmehrtens@maxlinear.com>
Extract the kmod-sched-prio and kmod-sched-red kernel modules from the
big kmod-sched package. This allows adding the two kernel modules to
OpenWrt without adding the kmod-sched and all its depdnecy.
Signed-off-by: Thomas Langer <tlanger@maxlinear.com>
Signed-off-by: Hauke Mehrtens <hmehrtens@maxlinear.com>
This puts the kmod-sched packages into an alphabetical order.
I kept the kmod-sched-core at the top as this is the main package.
No changes other than reordering were done.
Signed-off-by: Hauke Mehrtens <hmehrtens@maxlinear.com>
Change SCHED_MODULES_EXTRA to an explicit list of modules
instead of taking everything that is not filtered out.
This removes the need of updating the filter each time an extra
sch_*, act_* or similar is added with an own kmod definition.
Signed-off-by: Thomas Langer <tlanger@maxlinear.com>
Signed-off-by: Hauke Mehrtens <hmehrtens@maxlinear.com>
The sch_fq_codel.ko and the sch_fifo.ko are always compiled into the
kernel, they are activated in the generic kernel configuration. There is
no need to activate the build of these kernel modules in the kmod-sched*
packages.
Signed-off-by: Hauke Mehrtens <hmehrtens@maxlinear.com>
"The MCP2221 is a USB-to-UART/I2C serial converter which enables
USB connectivity in applications that have a UART and I2C interfaces."
<https://www.microchip.com/en-us/product/MCP2221>
Signed-off-by: Leo Soares <leo@hyper.ag>
(replaced GPIOLIB KConfig with @GPIO_SUPPORT)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
all other drivers depend on @GPIO_SUPPORT rather than
forcing CONFIG_GPIOLIB=y.
(I wonder what would happen if someone decides to try
UML with USBIP?)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This updates mac80211 to version 5.15.58-1 which is based on kernel
5.15.58.
The removed patches were applied upstream.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add driver for NVM Express block devices, ie. PCIe connected SSDs.
Targets which allow booting from NVMe (x86, maybe some mvebu boards come
to mind) should have it built-in, so rootfs can be mounted from there.
For targets without NVMe support in bootloader or BIOS/firmware it's
sufficient to provide the kernel module package.
On targets having the NVMe driver built-in the resulting kmod package
is an empty dummy. In any case, depending on or installing kmod-nvme
results in driver support being available (either because it was already
built-in or because the relevant kernel modules are added and loaded).
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Accessing the console on many devices is difficult.
netconsole eases debugging on devices that crash
after the network is up.
Reference to the netconsole documentation in upstream Linux:
<https://www.kernel.org/doc/html/latest/networking/netconsole.html>
|
|netconsole=[+][src-port]@[src-ip]/[<dev>],[tgt-port]@<tgt-ip>/[tgt-macaddr]
|
| where
| + if present, enable extended console support
| src-port source for UDP packets (defaults to 6665)
| src-ip source IP to use (interface address)
| dev network interface (eth0)
| tgt-port port for logging agent (6666)
| tgt-ip IP address for logging agent
| tgt-macaddr ethernet MAC address for logging agent (broadcast)
OpenWrt specific notes:
OpenWrt's device userspace scripts are attaching the network
interface (i.e. eth0) to a (virtual) bridge (br-lan) device.
This will cause netconsole to report:
|network logging stopped on interface eth0 as it is joining a master device
(and unfortunately the traffic/logs to stop at this point)
As a workaround, the netconsole module can be manually loaded
again after the bridge has been setup with:
insmod netconsole netconsole=@/br-lan,@192.168.1.x/MA:C...
One way of catching errors before the handoff, try to
append the /etc/modules.conf file with the following extra line:
options netconsole netconsole=@/eth0,@192.168.1.x/MA:C...
and install the kmod-netconsole (=y) into the base image.
Signed-off-by: Catalin Toda <catalinii@yahoo.com>
(Added commit message from PR, added links to documentation)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
the legacy driver was dropped in linux 5.14-rc3:
commit d249ff28b1d8 ("intersil: remove obsolete prism54 wireless driver")
Quoting Lukas Bulwahn:
"p54 replaces prism54 so users should be unaffected."
Reported-by: Marius Dinu <m95d+git@psihoexpert.ro>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
TechNexion PICO-PI-IMX7D uses BCM4339 Wi-Fi interface in SDIO mode.
Enable SDIO support for imx/cortexa7 to fully support it in images.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Add package supporting Bluetooth HCI interfaces connected over SDIO.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
[pepe2k@gmail.com: dropped rfkill dependency, other minor text fixes]
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Backport upstream fix to build on kernel 5.15.52 or later since kernel
devs backported newer functionality to older kernels.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
The mac80211-hwsim and the Intel iwlwifi driver support ieee80211ax, add
the missing DRIVER_11AX_SUPPORT dependency too.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
c07f45927839 firmware: update mt7622 firmware to version 20220630
af406a2d1c36 mt76: do not use skb_set_queue_mapping for internal purposes
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This external switch driver should be loaded on boot for network
support in failsafe mode.
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
This external switch driver should be loaded on boot for network
support in failsafe mode.
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
In Turris MOX SDIO card [1], which uses Marvell 88W997 and its driver
mwifiex, you might get cryptic messages, which are not helpful to use.
@pali created patch, which improves messages by the driver and he will
send this to Linux kernel soon.
Before:
[ 81.026156] mwifiex_sdio mmc1:0001:1: CMD_RESP: cmd 0x20 error, result=0x1
After:
[ 15.784018] mwifiex_sdio mmc1:0001:1: CMD_RESP: cmd RF_ANTENNA (0x20) error, result=0x1
Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
SDIO chip 88W9997 from NXP [1] is quite limited by its firmware and
driver. Add hacky patch to allow up to 4 SSID instead of 3 SSID.
Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
Introduce a new option background_radar to toggle hostapd's background
radar feature. Enabling this allows DFS CAC to run on dedicated radio RF
chains while the radio(s) are otherwise running normal AP activities on
other channels.
As OpenWrt configures hostapd to use a channel list even when a single
channel is configured, using this feature requires a list of channels in
/etc/config/wireless. Alternatively, channel can be set to auto.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: David Bauer <mail@david-bauer.net>
Enable ath10k offload by default. This improves wireless performance
without requiring user configuration.
This adds ath10k_core to the AUTOLOAD section so that the frame_mode
paramter can be added to /etc/modules.d and passed to the driver.
The frame_mode 2 enables ethernet mode on the firmware/driver.
This parameter is set by passing a different value to the frame_mode
value on kmod insmod.
Link to the original patchset:
https://patchwork.kernel.org/project/linux-wireless/cover/20220516032519.29831-1-ryazanov.s.a@gmail.com/
Signed-off-by: Tiago Gaspar <tiagogaspar8@gmail.com>
This reverts the airtime scheduler back from the virtual-time based scheduler
to the deficit round robin scheduler implementation.
This reduces burstiness and improves fairness by improving interaction with AQL.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
1696f9eb8b40 mt76: mt7915: do not copy ieee80211_ops pointer in mt7915_mmio_probe
a4db5869d660 mt76: mt7915: update mpdu density in 6g capability
500c18014d95 mt76: mt7915: add sta_rec with EXTRA_INFO_NEW for the first time only
3ef66fc7c714 mt76: do not check the ccmp pn for ONLY_MONITOR frame
dd682eead016 mt76: mt7915: update the maximum size of beacon offload
4fb991f2c997 mt76: mt7615: add sta_rec with EXTRA_INFO_NEW for the first time only
ba39ed3b44f1 mt76: mt76x02: improve reliability of the beacon hang check
fd8211cf7c59 mt76: mt7921: sync with updated patch
f2edd340ddb4 mt76: allow receiving frames with invalid CCMP PN via monitor interfaces
b6e865e2cc70 mt76: mt7615: fix throughput regression on DFS channels
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The MAC can be stored in OTP memory or in flash memory, currently the
driver could read it only from OTP. Backport the patch allowing setting
the MAC address from flash. Some modules have the OTP programmed but
the ODM/OEM decided to overwrite it with value stored in flash.
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
These narrowments are no longer useful, since there's no lower version
than 5.10 supported in tree.
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
4554ee652caf mt76: mt7921: fix warning Using plain integer as NULL pointer
a3f1d6ccf3ca mt76: mt7921: add missing bh-disable around rx napi schedule
9aeca2a5ce47 mt76: mt7921: get rid of mt7921_mcu_exit
fee8a5911c76 mt76: connac: move shared fw structures in connac module
db4d784ae7ba mt76: mt7921: move fw toggle in mt7921_load_firmware
16ab6bf49556 mt76: connac: move mt76_connac2_load_ram in connac module
29fd748801c6 mt76: connac: move mt76_connac2_load_patch in connac module
051c68d18214 mt76: mt7663: rely on mt76_connac2_fw_trailer
d6ae3505ac6c mt76: enable the VHT extended NSS BW feature
488a5ccc9762 mt76: mt7921: rely on mt76_dev in mt7921_mac_write_txwi signature
934029bb93e2 mt76: mt7915: rely on mt76_dev in mt7915_mac_write_txwi signature
ecefae4c7d72 mt76: connac: move mac connac2 defs in mt76_connac2_mac.h
b5eecc841df8 mt76: connac: move connac2_mac_write_txwi in mt76_connac module
012e619a07b9 mt76: connac: move mt76_connac2_mac_add_txs_skb in connac module
1b492be795ea mt76: mt7921: not support beacon offload disable command
f1f46d3b4b19 mt76: mt7921: fix command timeout in AP stop period
cae61112ef1d mt76: connac: move HE radiotap parsing in connac module
487674062643 mt76: connac: move mt76_connac2_reverse_frag0_hdr_trans in mt76-connac module
649bdc4983c4 mt76: connac: move mt76_connac2_mac_fill_rx_rate in connac module
cb75aaa39252 mt76: mt7921s: remove unnecessary goto in mt7921s_mcu_drv_pmctrl
e0eaf66eaebb mt76: mt7615: do not update pm stats in case of error
f8d125b4ea30 mt76: mt7921: do not update pm states in case of error
6329a834907e mt76: mt7921s: fix possible sdio deadlock in command fail
8a04f1b04662 mt76: mt7921: fix aggregation subframes setting to HE max
e52283439094 mt76: mt7915: disable UL MU-MIMO for mt7915
fd3958970e3d mt76: mt7921: enlarge maximum VHT MPDU length to 11454
18df38fe77f7 mt76: mt7915: get rid of unnecessary new line in mt7915_mac_write_txwi
149e95f5d7a6 mt76: connac: move mt76_connac_fw_txp in common module
899d192e8a79 mt76: move mt7615_txp_ptr in mt76_connac module
7184f0a6f6a5 mt76: connac: move mt76_connac_tx_free in shared code
c42d45278fa5 mt76: connac: move mt76_connac_tx_complete_skb in shared code
0993f4ef96f8 mt76: connac: move mt76_connac_write_hw_txp in shared code
467960fab791 mt76: connac: move mt7615_txp_skb_unmap in common code
2e758064b085 mt76: mt7915: rely on mt76_connac_tx_free
2065a7901671 mt76: move mcu_txd/mcu_rxd structures in shared code
576c1b7c472b mt76: move mt76_connac2_mcu_fill_message in mt76_connac module
7275f7758090 mt76: mt7915: fix incorrect testmode ipg on band 1 caused by wmm_idx
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This adds a few fixes for compiling against Linux 5.10:
1. segment_eq() has been removed with upstream commit
428e2976a5bf7e7f5554286d7a5a33b8147b106a ("uaccess: remove
segment_eq") and can use uaccess_kernel() instead
2. ioremap_nocache() is removed and is now an alias for ioremap() with
upstream commit 4bdc0d676a643140bdf17dbf7eafedee3d496a3c ("remove
ioremap_nocache and devm_ioremap_nocache")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
This backports encap offload support from upstream.
On some ath10k devices there can be about 10% improvement on tx throughput.
Users can turn it on by setting frame_mode=2.
Signed-off-by: Zhijun You <hujy652@gmail.com>
This patch adds support for the mainline kernel module for the PCA955x
LED driver. Note this requires i2c and GPIO support. Also worth calling
out this driver also enables GPIO support, depending on device tree
configuration.
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
Sync nl80211.h with upstream in order to maintain parity with
nl80211_copy.h shipped with hostapd.
This is necessary, as currently the enum value for
NL80211_EXT_FEATURE_RADAR_BACKGROUND mismatches between hostapd and
mac80211. This breaks background radar capability detection in hostapd.
Reported-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: David Bauer <mail@david-bauer.net>
In case no specific BSS color is configured, set it to a random value.
Signed-off-by: David Bauer <mail@david-bauer.net>
Tested-by: Stijn Tintel <stijn@linux-ipv6.be>
Delete the crypto-lib-blake2s kmod package, as BLAKE2s is now built-in.
Patches automatically rebased.
Build system: x86_64
Build-tested: ipq806x/R7800, x86/64
Signed-off-by: John Audia <therealgraysky@proton.me>
Major changes are:
Add support for smbd-direct multi-desctriptor.
Add support for dkms.
Add support for key exchange.
Fix seveal bugs.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Make ar8216/8327 swconfig driver modularizable and add
entry to the netdevices.mk kernel modules file.
Signed-off-by: Christian 'Ansuel' Marangi <ansuelsmth@gmail.com>
latency and short-term fairness is improved by fixing the tx queue sorting
so that it considers the pending AQL budget
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Needed by strongSwan IPsec VPN for strongswan-mod-chapoly. Not to be confused with
kmod-crypto-LIB-chacha20poly1305, which is an 8-byte nonce version used
by wireguard.
Signed-off-by: Xu Wang <xwang1498@gmx.com>
Add ieee80211_rx_check_bss_color_collision routine in order to introduce
BSS color collision detection in mac80211 if it is not supported in HW/FW
(e.g. for mt7915 chipset).
Add IEEE80211_HW_DETECTS_COLOR_COLLISION flag to let the driver notify
BSS color collision detection is supported in HW/FW. Set this for ath11k
which apparently didn't need this code.
Tested-by: Peter Chiu <Chui-Hao.Chiu@mediatek.com>
Co-developed-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://lore.kernel.org/r/a05eeeb1841a84560dc5aaec77894fcb69a54f27.1648204871.git.lorenzo@kernel.org
[clarify commit message a bit, move flag to mac80211]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David Bauer <mail@david-bauer.net>
Original patch: https://github.com/cifsd-team/ksmbd-tools/issues/227
adapted for ksmbd kernel module v3.4.3 by me.
Fixes crash in v3.4.3 only. Use original patch when updating to v3.4.4
as this one will fail hunk #1.
Signed-off-by: Marius Dinu <m95d+git@psihoexpert.ro>
Some ath10k IPQ40xx devices like the MikroTik hAP ac2 and ac3 require the
BDF-s to be extracted from the device storage instead of shipping packaged
API 2 BDF-s.
This is required as MikroTik has started shipping boards that require BDF-s
to be updated, as otherwise their WLAN performance really suffers.
This is however impossible as the devices that require this are release under
the same revision and its not possible to differentiate them from devices
using the older BDF-s.
In OpenWrt we are extracting the calibration data during runtime and we are
able to extract the BDF-s in the same manner, however we cannot package the
BDF-s to API 2 format on the fly and can only use API 1 to provide BDF-s on
the fly.
This is an issue as the ath10k driver explicitly looks only for the board.bin
file and not for something like board-bus-device.bin like it does for pre-cal
data.
Due to this we have no way of providing correct BDF-s on the fly, so lets
extend the ath10k driver to first look for BDF-s in the board-bus-device.bin
format, for example: board-ahb-a800000.wifi.bin
If that fails, look for the default board file name as defined previously.
So, backport the upstream ath10k patch.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Update ath10k-ct to the latest version which includes the backported
ath10k commit for requesting API 1 BDF-s with a unique name like caldata.
Signed-off-by: Robert Marko <robimarko@gmail.com>
HOST_LOADLIBES was renamed to KBUILD_HOSTLDLIBS in kernel 4.19. As the
oldest kernel version we support is 5.10, cleanup HOST_LOADLIBES use.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
With 5.4 out of the picture, remove LINUX_5_10 here. This is
needed for the WNDR4700 as otherwise kmod-usb3 isn't available
for 5.15.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
upstream linux have these watchdogs locked behind X86.
These will not build on other architectures. So move them
to target/linux/x86/modules.mk
drivers/watchdog/Kconfig:
|config F71808E_WDT
| tristate "Fintek F718xx, F818xx Super I/O Watchdog"
| depends on X86
|[...]
|config IT87_WDT
| tristate "IT87 Watchdog Timer"
| depends on X86
|[...]
|config ITCO_WDT
| tristate "Intel TCO Timer/Watchdog"
| depends on (X86 || IA64) && PCI
|[...]
|config W83627HF_WDT
| tristate "Watchdog timer for W83627HF/W83627DHG and compatibles"
| depends on X86
|[...]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
the Intel i6300esb is QEMU's default watchdog. And unlike
the real "Intel i6300ESB I/O Controller hub" hardware, the
i6300esb watchdog driver works on non-x86 targets like for
ARM (armvirt 32bit) and potentially virtual PowerPC and MIPS
targets (if there was any).
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The driver maintains elapsed times by repeatedly accumulating the time
since the previous update in a loop. For the elapsed showtime time, the
time difference is truncated to seconds before adding it, leading to a
sizable error over time.
Move the truncation to before calculation of the time difference in
order to remove this error. Also maintain the total elapsed time in the
same way in full seconds, to prevent the unsigned 32-bit counter from
wrapping around after about 50 days.
Testing on a VR9 device shows that the reported line uptime now matches
the actual elapsed wall time. The ADSL variant is only compile-tested,
but it should also work as the relevant code is identical.
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Right now, both ltq-adsl-mei and ltq-vdsl-mei are always built, even
when they aren't necessary for the selected variant. This can cause the
build to fail, for example ltq-vdsl-mei doesn't build successfully here
on xway target due to the vectoring callback.
Make these dependencies conditional on the specific package variants,
so they are only built when actually needed.
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
95ca1c3 nat46-core: ignore IPv4 options when translating packets
39778c2 add a module argument to ignore TOS translate for IPv4
9a36ee1 add a module argument to ignore TOS translate for IPv4
79190a8 add a module argument to ignore TOS translate for IPv4
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
This reverts commit f9ff282d17 as during
upstream patch review process nbd pointed out, that this patch needs
more work:
"The patch looks wrong to me. I'm pretty sure that AR_CH0_TOP2 is the
correct register, the definition has an explicit check for 9561 as well.
I believe this patch works by accident because it avoids writing a wrong
value to that register."
1. https://lore.kernel.org/all/91c58969-c60e-2f41-00ac-737786d435ae@nbd.name
Signed-off-by: Petr Štetiar <ynezz@true.cz>
ath9k is setting the TX PA DC bias level different on QCA9561 and QCA9565
although they have the same radio IP-core, which results in a very low
output power and very low throughput as devices are further away from
the AP (compared to other 2.4GHz APs.)
In real life testing, without this patch the 2.4GHz throughput on Yuncore
XD3200 is around 10Mbps sitting close to the AP, and close to theoretical
maximum with the patch applied.
Signed-off-by: Clemens Hopfer <openwrt@wireloss.net>
[edit commit message]
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
Upstream in commit 34a1dee6bc44 ("net: usb: asix: ax88772: add generic
selftest support") in version 5.14 added dependency on generic selftest
functionality and armvirt/64 when compiled with ALL_KMODS=y reports following:
Package kmod-usb-net-asix is missing dependencies for the following libraries:
mdio_devres.ko
selftests.ko
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Upstream in commit 3e1e58d64c3d ("net: add generic selftest support") in
version 5.13 added generic selftests module and usb-net-asix already
depends on it, in version 5.18 via commit 1710b52d7c13 ("net: usb:
smsc95xx: add generic selftest support") it will be used by
usb-net-smsc95xx as well.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
armvirt/64 when compiled with ALL_KMODS=y reports following:
Package kmod-usb-net-smsc95xx is missing dependencies for the following libraries:
libphy.ko
Signed-off-by: Petr Štetiar <ynezz@true.cz>
armvirt/64 when compiled with ALL_KMODS=y reports following:
Package kmod-mdio-devres is missing dependencies for the following libraries:
of_mdio.ko
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Upstream in commit bc1bee3b87ee ("net: mdiobus: Introduce
fwnode_mdiobus_register_phy()") in version 5.14 introduced new
dependency:
Package kmod-of-mdio is missing dependencies for the following libraries:
fwnode_mdio.ko
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Both legacy iptables and nftables require nf-log modules for rule logging,
so move them into a separate package both firewall implementations can
depend on.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
This updates mac80211 to version 5.15.33-1 which is based on kernel
5.15.33.
The removed patches were applied upstream.
This new release contains many fixes which were merged into the upstream
Linux kernel.
This also contains the following new drivers which are needed for ath11k:
* net/qrtr/
* drivers/bus/mhi/
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Fix compilation and usage under kernel 5.15 for the mwlwifi driver.
For detailed description of changes, check individual patches.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
bh_event_add_var can be called by multiple threads concurrently,
so it shall not use a static char buffer
Signed-off-by: Andrey Erokhin <a.erokhin@inango-systems.com>
5beb87716e70 mt76: dma: add wrapper macro for accessing queue registers
e0bc736d5617 mt76: add support for overriding the device used for DMA mapping
b8c842daa081 mt76: make number of tokens configurable dynamically
87a962e0608f mt76: mt7915: add Wireless Ethernet Dispatch support
2accb74e6be3 mt76: mt7915: fix using null pointer when wfsys on
e5227f2f3120 mt76: mt7921: Fix the error handling path of mt7921_pci_probe()
ec0e9f4da32f mt76: mt7915: fix possible uninitialized pointer dereference in mt7986_wmac_gpio_setup
5a87be892ba7 mt76: mt7915: fix possible NULL pointer dereference in mt7915_mac_fill_rx_vector
fe441e5d3dcf mt76: mt7915: do not pass data pointer to mt7915_mcu_muru_debug_set
f3ddfe886283 mt76: mt7915: report rx mode value in mt7915_mac_fill_rx_rate
2a0d370cb5fe mt76: mt7915: use 0xff to initialize bitrate_mask in mt7915_init_bitrate_mask
506bb0605e3e mt76: mt7921: Add AP mode support
Signed-off-by: Felix Fietkau <nbd@nbd.name>
MHI WWAN CTRL allows QCOM-based PCIe modems to expose different modem
control protocols/ports to userspace, including AT, MBIM, QMI, DIAG
and FIREHOSE. These protocols can be accessed directly from userspace
(e.g. AT commands) or via libraries/tools (e.g. libmbim, libqmi, libqcdm)
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
This driver provides MHI PCI controller driver for devices
such as Qualcomm SDX55 based PCIe modems
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Previously commit openwrt/packages@3abb7cb ("lvm2: Added script and updated Makefile[...]")
couldn't actually work and allow rootfs_data to be stored on a LVM2 as
the necessary kernel modules had not been loaded at this point.
Fix this by loading device-mapper modules early at boot.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Use the kernel's built-in formula for computing this value.
The value applied by OpenWRT's sysctl configuration file does not scale
with the available memory, under-using hardware capabilities.
Also, that formula also influences net.netfilter.nf_conntrack_buckets,
which should improve conntrack performance in average (fewer connections
per hashtable bucket).
Backport upstream commit for its effect on the number of connections per
hashtable bucket.
Apply a hack patch to set the RAM size divisor to a more reasonable value (2048,
down from 16384) for our use case, a typical router handling several thousands
of connections.
Signed-off-by: Vincent Pelletier <plr.vincent@gmail.com>
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Fixes following issue:
Package kmod-drm-imx-ldb is missing dependencies for the following libraries:
drm_dp_aux_bus.ko
Introduced upstream in commit aeb33699fc2c ("drm: Introduce the DP AUX
bus") in kernel version 5.15.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Fixes following issue:
Package kmod-drm is missing dependencies for the following libraries:
fb.ko
Introduced upstream in commit f611b1e7624c ("drm: Avoid circular
dependencies for CONFIG_FB") in 5.14.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Fixes following build issues:
Package kmod-r8169 is missing dependencies for the following libraries:
mdio_devres.ko
Package kmod-ixgbe is missing dependencies for the following libraries:
mdio_devres.ko
Package kmod-amd-xgbe is missing dependencies for the following libraries:
mdio_devres.ko
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Add new module require in 5.15
- Changes in block module
- Changes in netfilter module (log module unified)
- Changes in fs module (mainly new depends for cifs and new ntfs3 module)
- Changes in lib add shared lib now used by more than 1 kmod
- Changes in crypto, dropped one crypto algo added arm crypto accellerator
- Changes in other, add zram default compressor choice and missing lib
by tpm module
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Albeit a separate crypto module, lzo-rle uses the same kernel library as lzo.
Crypto API users (zram, for example) expect both lzo and lzo-rle to be
available, so let's include lzo-rle (about 5.5 kiB) in the lib-lzo package.
Based on e9hack's original patch: https://patchwork.ozlabs.org/project/openwrt/patch/541cbfbd-76f2-59b3-a867-47b6f0fc7da9@gmail.com/
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Some users noticed repeated resyncs at random intervals, which go away
when the MEI driver is configured to use polling instead of interrupts.
Debugging shows that this seems to be caused by concurrent calls to
MEI_ReadMailbox (in the interrupt handler) and MEI_WriteMailbox. This
appears to be mostly triggered when there is an interrupt for vectoring
error reports.
In polling mode, calls to MEI_ReadMailbox are protected by the same
semaphore as is used in MEI_WriteMailbox. When interrupts are used,
MEI_WriteMailbox appears to rely on MEI_DisableDeviceInt and
MEI_EnableDeviceInt to provide mutual exclusion with the interrupt
handler. These functions mask/unmask interrupts, and there is an
additional check of the mask in the interrupt handler itself. However,
this is not sufficient on systems with SMP, as the interrupt handler
may be running in parallel, and could already be past the interrupt
mask check at this point.
This adds a lock to the interrupt handler, and also acquires this lock
in MEI_DisableDeviceInt. This should make sure that after a call to
MEI_DisableDeviceInt the interrupt is masked, and the interrupt handler
is either not running, has alread finished its work, or is still before
the interrupt mask check, and is thus going to detect the change.
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
This re-enables the vectoring error sample callback and adds a
dependency to the corresponding driver.
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
In order to calculate the required pre-distortion for downstream
vectoring, the vectoring control entity (VCE) at the carrier office
needs error samples from the modem. On Lantiq VR9 modems, error reports
are generated by the firmware, but need to be multiplexed into the data
stream by the driver on the main processor when L2 encapsulation is
selected by the VCE.
This driver provides the necessary callback function, which is called by
the MEI driver after receiving an error report from the firmware.
Originally, it is part of the Lantiq PPA driver, but after a few changes
it also works with the PTM driver used in OpenWrt. The direct call to
ndo_start_xmit needs to be replaced, as the PTM driver relies on locks
from the kernel. Instead dev_queue_xmit is used, which is called from a
work queue, as it is not safe to call from an interrupt handler.
Additional changes include fixes to support recent kernel versions and
a change of the used interface from ptm0 to dsl0.
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
378b638c70c0 mt76: mt7915: fix unused variable with testmode disabled
4f4309542862 mt76: mt7915: only use u32_get_bits with constant value
de06d828a0bf mt76: mt7921: fix injected MPDU transmission to not use HW A-MSDU
c007ba3ec7a9 mt76: mt7915: simplify conditional
64c74dc93f68 mt76: fix dfs state issue with 160 MHz channels
d3471b0d92c1 mt76: mt7615: honor ret from mt7615_mcu_restart in mt7663u_mcu_init
f4c87b32e0e9 mt76: mt7663u: introduce mt7663u_mcu_power_on routine
82de5987af54 mt76: mt7921: fix up the monitor mode
c501df4086e1 mt76: mt7921: use mt76_hw instead of open coding it
594ee03d5a11 mt76: mt7915: fix DFS no radar detection event
d8d2b383a241 mt76: split single ldpc cap bit into bits
0f336fba20fe mt76: mt7921: make mt7921_init_tx_queues static
00a066ce9914 mt76: mt7921: fix xmit-queue dump for usb and sdio
d6d2479568b2 mt76: mt7921: fix mt7921_queues_acq implementation
d17b74420199 mt76: fix monitor mode crash with sdio driver
c374559eae6f mt76: mt7915: allow beaconing on all chains
b219af63b9ce mt76: connac: add 6 GHz support for wtbl and starec configuration
630384cb3246 mt76: mt7915: add 6 GHz support
28ff1bddc7e8 mt76: mt7915: fix eeprom fields of txpower init values
d4b226cc15e7 mt76: mt7915: add txpower init for 6GHz
31e820d4ce4b mt76: mt7921: get rid of mt7921_wait_for_mcu_init declaration
9fee1faf6028 mt76: mt7915: check for devm_pinctrl_get() failure
31a970940b97 mt76: connac: make read-only array ba_range static const
e49af7036bbc mt76: use le32/16_get_bits() whenever possible
0664d39039c2 mt76: fix invalid rssi report
f16fc9d96105 mt76: mt7915: set band1 TGID field in tx descriptor
67ce2708dcef mt76: mt7915: fix beamforming mib stats
6e899abec818 mt76: mt7915: fix phy cap in mt7915_set_stream_he_txbf_caps()
c6780c85cff2 mt76: mt7915: fix typos in comments
aa6eadc09a83 mt76: usb: add req_type to ___mt76u_rr signature
74a519ab8353 mt76: usb: add req_type to ___mt76u_wr signature
2651d2c66cbd mt76: usb: introduce __mt76u_init utility routine
c03e095eee27 mt76: mt7921: disable runtime pm for usb
41085cdcd7e3 mt76: mt7921: update mt7921_skb_add_usb_sdio_hdr to support usb
e700aba6bae3 mt76: mt7921: move mt7921_usb_sdio_tx_prepare_skb in common mac code
056b7f4ebcc6 mt76: mt7921: move mt7921_usb_sdio_tx_complete_skb in common mac code.
0abf682a3def mt76: mt7921: move mt7921_usb_sdio_tx_status_data in mac common code.
b0c60d5252de mt76: mt7921: add mt7921u driver
053668acdaf8 mt76: mt7921: move mt7921_init_hw in a dedicated work
Signed-off-by: Felix Fietkau <nbd@nbd.name>
LOCK_STATE_HELD define was omitted during backport of
lockdep_assert_not_held() which leads to build failures of kernels with
CONFIG_LOCKDEP=y:
backports-5.15.8-1/backport-include/linux/lockdep.h:16:47: error: 'LOCK_STATE_HELD' undeclared (first use in this function)
Fix it by adding missing LOCK_STATE_HELD define.
References: PR#9373
Reported-by: Oskari Rauta <oskari.rauta@gmail.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Add option to compile kmod-inet-diag, support for INET (TCP, DCCP, etc)
socket monitoring interface used by native Linux tools such as ss.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Both struct net_device_path_ctx and struct net_device_path
are not available in 5.4. This causes an build error on the
bcm63xx target.
|mac80211/driver-ops.h: In function 'drv_net_fill_forward_path':
|driver-ops.h:1502:57: error: passing argument 4 of
|'local->ops->net_fill_forward_path' from incompatible pointer type
| [-Werror=incompatible-pointer-types]
| 1502 | ctx, path);
| | ^~~
| | |
| | struct net_device_path_ctx *
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Package the ability to log kernel crashes to 'ramoops' pstore
files into RAM in /sys/fs/pstore
Reference to the ramoops admin guide in upstream Linux:
https://www.kernel.org/doc/html/v5.10/admin-guide/ramoops.html
The files in RAM survive a warm reboot, but not a cold reboot.
Note: kmod-ramoops selects kmod-pstore and kmod-reed-solomon.
The feature can be used by selecting the kmod-ramoops and
adding a ramoops reserved-memory definition to the device DTS.
Example from R7800:
reserved-memory {
rsvd@5fe00000 {
reg = <0x5fe00000 0x200000>;
reusable;
};
ramoops@42100000 {
compatible = "ramoops";
reg = <0x42100000 0x40000>;
record-size = <0x4000>;
console-size = <0x4000>;
ftrace-size = <0x4000>;
pmsg-size = <0x4000>;
};
};
If no definition has been made in DTS, no crash log is stored
for the device.
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
(added CONFIG_EFI_VARS_PSTORE disable)
This commit adds the following package compile options.
CONFIG_PACKAGE_RTW88_DEBGUG:
Compile the driver with additional debug logging output
CONFIG_PACKAGE_RTW88_DEBGUGFS:
Add the possibility to map information about the driver rtw88 into
debugfs.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
package hwmon's lm70.ko. This module supports the
National Semiconductor/TI LM70,LM71,LM74 and
TI TMP121,TMP122,TMP123 and TMP124 chips (all SPI).
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
ksmbd is an upstream linux alternative to Samba which is lighterweight
and more performant, especially on underpowered devices.
Moving it here from the packages feed as it is now an upstream kernel
module. Also easier to update as version updates can be coordinated better
The next LTS kernel (5.15) has this included. A depend on kernel < 5.15
will need to be added later.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
This module was used solely by Buffalo WZR-HP-G300NH devices
and has become obsolete with the introduction of gpio-cascade.
Signed-off-by: Mauri Sandberg <maukka@ext.kapsi.fi>
Adds new kernel module for GPIO controlled multiplexer support.
Signed-off-by: Mauri Sandberg <maukka@ext.kapsi.fi>
Signed-off-by: Petr Štetiar <ynezz@true.cz> [missing commit description]
Now that we have separate files for each kernel version,
only the version/hash for the target kernel are available.
This cause a missing hash error (and wrong kernel version) for
bpf-headers when a testing kernel version is used for the current target.
Fix this error by manually including the kernel version/hash file for the
specific kernel version requested.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
this should have been removed together with linux 5.4 APM821XX
support. Currently, this didn't hurt or broke something. But it
will in the next stable kernel release.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The SDK does not ship the generic platform files. Use relative path for
GENERIC_PLATFORM_DIR to make it work. This points it at the files from
the feed directory instead of the base SDK path
Signed-off-by: Felix Fietkau <nbd@nbd.name>
All devices which used this package migrated to the kernel GPIO-line
watchdog driver and configure it over their DT.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Add option to compile kmod-vrf, support for Virtual Routing and
Forwarding (Lite).
This module depends on NET_L3_MASTER_DEV, which is a boolean kernel
option, so we need to create a configuration option also for this, and
make kmod-vrf depend on it.
Signed-off-by: Marek Behún <kabel@kernel.org>
nf-nathelper-extra and nf-conntrack-netlink had iptables related
dependencies, yet, when looking for the respective kernel symbols and
checking it's dependencies it was confirmed that iptables wasn't
required and that these were either it's own moodule or tool independent
(nftables or iptables).
Correct these and make sure no unneeded extras are pulled in.
Signed-off-by: Tiago Gaspar <tiagogaspar8@gmail.com>
This removes -static compile option. The -static option tells GCC to
link this statically with the libc, which we do not want in OpenWrt. We
want to link everything dynamically to the libc. This fixes a compile
problem with glibc.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
x86, mt7623 and others buildbot failed due to:
|Package kmod-hwmon-nct7802 is missing dependencies for the following libraries:
|regmap-core.ko
|regmap-i2c.ko
Fixes: 1ed50b92d1 ("package: kernel: add driver module for NCT7802Y")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This commit add package with hwmon-nct7802 module.
This driver implements support for the Nuvoton NCT7802Y hardware monitoring
chip. NCT7802Y supports 6 temperature sensors, 5 voltage sensors, and 3 fan
speed sensors.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
(fixed c&p'ed module description)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Almost all targets have the fixed-phy feature built into the kernel.
One big exception is x86. This caused a problem with the upcoming
LAN78xx usb driver. Hence this patch breaks out the fixed-phy from
of_mdio (which didn't include the .ko) and puts into a separate
module.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
phy drivers for Microchip's LAN88xx PHYs.
This is needed for the "LAN7801" variant
of the upstream lan78xx usb ethernet driver.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Linux upstream commit 9370f2d05a
add load firmware file through request_firmware,this affect the
nanopi r2s and some USB adapters in kernel 5.10 with this error:
'r8152 4-1:1.0: unable to load firmware patch rtl_nic/rtl8153b-2.fw'
This patch split the USB NIC firmware files from r8169 firmware,
and adds r8152-firmware to r8152 driver.
Add kmod-usb-net-cdc-ncm to support RTL8156A and RTL8156B 2.5G ethernet
adapters supported since v5.13-rc1.
195aae321c
Signed-off-by: Marty Jones <mj8263788@gmail.com>
ARC4 was used for WEP, which is not secure anymore. Therefor it is
disabled in the driver, but the code is not removed for now.
Signed-off-by: Daniel Kestrel <kestrel1974@t-online.de>
The lantiq AES hardware does not support the gcm algorithm. But it
can be implemented in the driver as a combination of the aes_ctr
algorithm and the xor plus gfmul operations for the hashing.
Due to the wrapping of the several algorithms and the inefficient
16 byte block by 16 byte block invokation in the kernel
implementations, this driver is about 3 times faster for the larger
block sizes.
Signed-off-by: Daniel Kestrel <kestrel1974@t-online.de>
After adding xts and cbcmac the aes algorithm source had three sections
for setting the aes key to the hardware which are identical.
Method aes_set_key_hw was created which is now called from within the
spinlock secured control sections in methods ifx_deu_aes, ifx_deu_aes_xts
and aes_cbcmac_final_impl and reduces the size of ifxmips_aes.c.
Signed-off-by: Daniel Kestrel <kestrel1974@t-online.de>
Since commit 53b6783 hostapd is using the kernel api which includes the
cbcmac-aes shash algorithm. The kernels implementation is a wrapper around
the aes encryption algorithm, which encrypts block (16 bytes) by block.
When the ltq-deu driver is present, it uses hardware aes, but every 16 byte
encrypt requires setting the key. This is very inefficient and is a huge
overhead. Since the cbcmac-aes is simply a hash that uses the cbc aes
algorithm starting with an iv set to x'00' with an optional ecb aes
encryption of a possible last incomplete block that is padded with the
positional bytes of the last cbc encrypted block, this algorithm is now
added to the driver. Most of the code is derived from md5-hmac and
tailored for aes. Tested with the kernels crypto testmgr including extra
tests against the kernels generic ccm module implementation.
This patch also fixes the overallocation in the aes_ctx that is caused
by using u32 instead of u8 for the aes keys.
Signed-off-by: Daniel Kestrel <kestrel1974@t-online.de>
Remove the dependency on kernel 5.4 from the Makefile to allow the
driver to compile with kernel 5.10 or kernel versions higher than
5.4.
Signed-off-by: Daniel Kestrel <kestrel1974@t-online.de>
The lantiq AES hardware does not support the xts algorithm. Apart
from the cipher text stealing (XTS), the AES XTS implementation is
just an XOR with the IV, followed by AES ECB, followed by another
XOR with the IV and as such can be also implemented by using the
lantiq hardware's CBC AES implemention plus one additional XOR with
the IV in the driver. The output IV by CBC AES is also not usable
and the gfmul operation not supported by lantiq hardware. Both need
to be done in the driver too in addition to the IV treatment which is
the initial encryption by the other half of the input key and to
set the IV to the IV registers for every block.
In the generic kernel implementation, the block size for XTS is set
to 16 bytes, although the algorithm is designed to process any size
of input larger than 16 bytes. But since there is no way to
indicate a minimum input length, the block size is used. This leads
to certain issues when the skcipher walk functions are used, e.g.
processing less than block size bytes is not supported by calling
skcipher_walk_done.
The walksize is 2 AES blocks because otherwise for splitted input
or output data, less than blocksize is to be returned in some cases,
which cannot be processed. Another issue was that depending on
possible split of input/output data, just 16 bytes are returned while
less than 16 bytes were remaining, while cipher text stealing
requires 17 bytes or more for processing.
For example, if the input is 60 bytes and the walk is 48, then
processing 48 bytes leads to a return code of -EINVAL for
skcipher_walk_done. Therefor the processed counter is used to
figure out, when the actual cipher text stealing for the remaining
bytes less than blocksize needs to be applied.
Measured with cryptsetup benchmark, this XTS AES implementation is
about 19% faster than the kernels XTS implementation that uses the
hardware ECB AES (ca. 18.6 MiB/s vs. 15.8 MiB/s decryption 256b key).
The implementation was tested with the kernels crypto testmgr against
the kernels generic XTS AES implementation including extended tests.
Signed-off-by: Daniel Kestrel <kestrel1974@t-online.de>
The processing in the hmac algorithms depends on the status fields:
count, dbn and started. Not all were initialised in the init method
and after finishing the final method. Added missing fields to init
method and call init method after finishing final.
The memsets have the wrong size in the original driver and did not
clear everything and are not necessary. Since no memset is done in
the kernels generic implementation, memsets were removed.
Signed-off-by: Daniel Kestrel <kestrel1974@t-online.de>
Removing hash pointer in _hmac_setkey since its not needed and causes
a compiler warning.
Make the spinlock control sections shorter and move initializations
out of the control sections to free the spinlock faster for allowing
other threads to use the hash engine.
Minor improvements for indentation and removal of blanks and blank
lines in some areas.
Signed-off-by: Daniel Kestrel <kestrel1974@t-online.de>
Exceeding the temp array size was not checked and instead storage not
allocated by the driver was used/overwritten which in most cases
resulted in reboots. This patch implements processing the input to the
hash algorithm in tempsize chunks.
The _hmac_final methods were changed to _hmac_final_impl adding a
parameter that indicates intermediate or final processing. The started
variable was added to the context to indicate, if there is an
intermediate result in the context. For sha1_hmac the variable to store
the intermediate hash was added to the context too.
In order to avoid md5_hmac_final_impl being recursively called if the
padding of the input and the resulting last transform during the hmac
algorighms final processing causes the temp array to overflow and to
make sure that there is at least one block in the temp array when the
_hmac_final for final processing is called, the check for exceeding
the temp array in _hmac_transform was moved before copying the block
and incrementing dbn. dbn needs to be at least 1 at final processing
time to let the hash engine apply the opad operation.
To make the hash engine not apply the hmac algorithms final opad
operation, for intermediate processing the dbn in the control register
is set to a higher value than number of dbns are actually processed.
Signed-off-by: Daniel Kestrel <kestrel1974@t-online.de>
The hmac algorithms state, that keys larger than the key size should be
hashed with the underlying hash algorithms and then those hashes are to
be used as keys. This patch implements this. In order to avoid allocating
a descriptor during setkey, a shash_desc pointer is added to the context.
Another issue for multithreaded callers is the shared temp array.
The temp array is static and as such would be shared among multithreaded
callers, which obviously would neither work nor produce correct results.
The temp array (4k size) is moved to the context and since the size of
the context is limited, it can only be defined as pointer otherwise the
initialisation of the hash algorithm fails.
The allocations and freeing of both the temp and the desc pointer in the
context are done by implementing cra_init and cra_exit functions for
the hmac algorithms.
Also improved indentation in some areas.
Signed-off-by: Daniel Kestrel <kestrel1974@t-online.de>
Error ifxdeu-ctr-rfc3686(aes) (16) doesn't match generic impl (20) occurs
when running the cryptomgr extra tests that compare against the linux
kernels generic implementation.
Signed-off-by: Daniel Kestrel <kestrel1974@t-online.de>
The algorithms sha1, sha1_hmac and md5_hmac all use ENDI=1. The md5
algorithm uses ENDI=0 and the endian_swap methods to reverse the
endianess switch by using user CPU time, which is unnecessary overhead.
Danube and AR9 devices do not set endianess for SHA1, so is done for
MD5.
Furthermore the patch replaces endian_swap with le32_to_cpu for md5 and
md5 hmac algorithms and removes endian_swap for them.
The init functions initialize the algorithm in the hardware. The lock is
not used to write to the control register. If another thread calls
another hash algo before update or final, the result will be wrong.
Therefore move the algorithm init to the lock protected sections in the
transform or final methods.
Setting the hw key for the hmac algorithms is now done from within the
lock protected sections in their final methods. The lock protecting is
removed from the _hmac_setkey_hw functions.
In final for md5 and sha1 the lock section is removed, because all the
work was already done in transform (which is called from final). As such
only copying the hash to the output is required.
MD5 and MD5_HMAC produce 16 byte hashes (4 DWORDS) only, therefor
writing register D5R to the hash output is removed for MD5_HMAC.
Signed-off-by: Daniel Kestrel <kestrel1974@t-online.de>
All hash algorithms use the same base IFX_HASH_CON to access the hash unit.
Parallel threads should not be able to call different hash algorithms and
therefor a global lock is required.
Fixed linker warning, that md5_hmac_init, md5_hmac_update and
md5_hmac_final are static export symbols. The export symbols are not
required, because the functions are exposed using shash_alg structure.
Signed-off-by: Daniel Kestrel <kestrel1974@t-online.de>
The functions ifx_deu_aes_cfg and ifx_deu_aes_ofb have been part of the
driver ever since. But the functions and definitions to make the
algorithms actually usable were missing.
This patch adds the neccessary code for aes_ofb and aes_cfb algorithms.
Signed-off-by: Daniel Kestrel <kestrel1974@t-online.de>
When running cryptomgr tests against the driver, there are several
occurences of different errors for even and uneven splitted data in the
underlying scatterlists for the ctr and ctr_rfc3686 algorithms which are
now fixed.
Fixed error in ctr_rfc3686_aes_decrypt function which was introduced with
the previous commit by using CRYPTO_DIR_ENCRYPT in the decrypt function.
Signed-off-by: Daniel Kestrel <kestrel1974@t-online.de>
When running cryptomgr tests against the driver, there are several
occurences of different errors for setkey of des and des3-ede
algorithms.
Those key checks are already implemented in the kernels des
implementation, so this is added as dependency and the kernel methods
are called. It also required adding the kernels des/des3 context
definitions to the des_ctx internal structure to be able to call the
kernel methods.
Fixed ifxdeu-des... setkey unexpectedly succeeded on test vector x;
expected_error=-22.
Fixed ifxdeu-des... setkey failed on test vector x; expected_error=0,
actual_error=-22.
Renamed des_ctx internal structure and des_encrypt/des_decrypt methods
because they are already defined in the kernel module.
Fixed wrong DES_xxx constant definitions in crypto_alg definition for
ifxdeu_des3_ede_alg.
Fixed method comment errors.
Signed-off-by: Daniel Kestrel <kestrel1974@t-online.de>
The <linux/cryptohash.h> was removed with Linux 5.8, because it only
contained the library implementation of SHA1, which was folded
into <crypto/sha.h>.
So switch this driver away from using <linux/cryptohash.h>.
Signed-off-by: Daniel Kestrel <kestrel1974@t-online.de>
Convert blkcipher to skcipher for the synchronous versions of AES,
DES and ARC4.
The Block Cipher API was depracated for a while and was removed with
Linux 5.5. So switch this driver to the skcipher API.
Signed-off-by: Daniel Kestrel <kestrel1974@t-online.de>
Some devices initialize AES during boot and AES works out of the box
and the correct endianess is set.
NDC means (No Danube Compatibility Mode) and the endianess setting has
no effect if its set to 0.
NDC 0: OFF ENDI bit cannot be written as in Danube
To make it work for other devices, the NDC control register needs to
be set to 1.
Signed-off-by: Daniel Kestrel <kestrel1974@t-online.de>
OpenSSL with cryptdev support uses the data encryption unit (DEU) driver
for hard accelerated processing of ciphers/digests, if the flag
CRYPTO_ALG_KERN_DRIVER_ONLY is set.
Signed-off-by: Mathias Kresin <dev@kresin.me>
[fix commit title prefix]
Signed-off-by: Daniel Kestrel <kestrel1974@t-online.de>
Even if the minimum blocksize is set to 16 (AES_BLOCK_SIZE), the crypto
manager tests pass 499 bytes of data to the aes-ctr encryption, from
which only 496 bytes are actually encrypted.
Reading the comment regarding the minimum blocksize, it only states that
it's the "smallest possible unit which can be transformed with this
algorithm". Which doesn't necessarily mean, the data have to be a
multiple of the minimal blocksize.
All kernel hardware crypto driver enforce a minimum blocksize of 1,
which perfect fine works for the lantiq data encryption unit as well.
Lower the blocksize limit to 1, to process not padded data as well.
In AES for processing the remaining bytes, uninitialized pointers
were used.
This patch fixes using uninitialized pointers and wrong offsets.
Signed-off-by: Mathias Kresin <dev@kresin.me>
[fix commit title prefix]
Signed-off-by: Daniel Kestrel <kestrel1974@t-online.de>
When handling non-aligned remaining data (not padded to 16 byte
[AES_BLOCK_SIZE]), a full 16 byte block is read from the input buffer
and written to the output buffer after en-/decryption.
While code already assumes that an input buffer could have less than 16
byte remaining, as it can be seen by the code zeroing the remaining
bytes till AES_BLOCK_SIZE, the full AES_BLOCK_SIZE is read.
An output buffer size of a multiple of AES_BLOCK_SIZE is expected but
never validated.
To get rid of the read/write behind buffer, use a temporary buffer when
dealing with not padded data and only write as much bytes to the output
as we read.
Do not memcpy directly to the register, to make used of the endian swap
macro and to trigger the crypto start operator via the ID0R to trigger
the register. Since we might need an endian swap for the output in
future, use a temporary buffer for the output as well.
The issue could not be observed so far, since all caller of ifx_deu_aes
will ignore the padded (remaining) data. Considering that the minimum
blocksize for the algorithm is set to AES_BLOCK_SIZE, the behaviour
could be called expected.
Signed-off-by: Mathias Kresin <dev@kresin.me>
[fix commit title prefix]
Signed-off-by: Daniel Kestrel <kestrel1974@t-online.de>
The crypto algorithms are registered and available to the system before
the chip is actually powered on and the generic parameter for the DEU
behaviour set.
The issue can mainly be observed if the crypto manager tests are enabled
in the kernel config. The crypto manager test run directly after an
algorithm is registered.
Signed-off-by: Mathias Kresin <dev@kresin.me>
[fix commit title prefix]
Signed-off-by: Daniel Kestrel <kestrel1974@t-online.de>
This patch adds kernel module for Global Mixed-mode Technology Inc
G762 and G763 fan speed PWM controller chips.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Based on: 1ac627024d ("kernel: ath10k-ct: provide a build variant for
small RAM devices")
Like described in the ath10k-ct-smallbuffers version, oom-killer gets
triggered frequently by devices with small RAM.
That change is necessary for many community mesh networks which use
ath10k based devices with too little RAM. The -ct driver has been
proven unstable if used with 11s meshing and only wave2 chipsets are
supporting 11s. Freifunk Berlin is nowadays assembling its
firmware-based completely of vanilla OpenWRT with some package additions
which are made through the imagebuilder. Therefore we cannot take the
approach other freifunk communities have taken to maintain that patch
downstream [1]. Other communities consider these devices as broken and
that change would pretty much give those devices a second life [2].
[1] - 450b306e54
[2] - https://github.com/freifunk-gluon/gluon/issues/1988#issuecomment-619532909
Signed-off-by: Simon Polack <spolack+git@mailbox.org>
Signed-off-by: Nick Hainke <vincent@systemli.org>
Add a new target named "qoriq", that will support boards using PowerPC
processors from NXP's QorIQ brand.
This doesn't actually add support for any board yet, so that
installation instructions can go in the commit message of the commit
that adds actual support for a board.
Using CONFIG_E6500_CPU here due to the kernel using -mcpu=powerpc64
rather than -mcpu=e5500 when selecting CONFIG_E5500_CPU. The only
difference between e5500 and e6500 is AltiVec support, and the kernel
checks for it at runtime. Musl will only check at runtime if AltiVec
support is disabled at compile-time, so we need to use e5500 in CPU_TYPE
to avoid SIGILL.
Math emulation (CONFIG_MATH_EMULATION_HW_UNIMPLEMENTED) is required, as
neither e5500 nor e6500 implement fsqrt nor fsqrts, and musl hardcodes
sqrt and sqrtf to use these ASM instructions on PowerPC64.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Reviewed-by: Rui Salvaterra <rsalvaterra@gmail.com>
The following patches were backported from upstream before and are not
needed any more:
package/kernel/mac80211/patches/ath10k/081-ath10k-fix-module-load-regression-with-iram-recovery-feature.patch
package/kernel/mac80211/patches/ath10k/980-ath10k-fix-max-antenna-gain-unit.patch
package/kernel/mac80211/patches/build/010-headers-Add-devm_platform_get_and_ioremap_resource.patch
package/kernel/mac80211/patches/subsys/300-mac80211-drop-check-for-DONT_REORDER-in-__ieee80211_.patch
package/kernel/mac80211/patches/subsys/307-mac80211-do-not-access-the-IV-when-it-was-stripped.patch
package/kernel/mac80211/patches/subsys/308-mac80211-fix-radiotap-header-generation.patch
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
update rtl8812au-ct driver to be ready for 5.15 Linux.
Signed-off-by: Janpieter Sollie <janpieter.sollie@edpnet.be>
[added commit message from PR with changes, added tag to subject]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
By default CONFIG_BTRFS_FS_POSIX_ACL is disabled, it should be enabled
only when you enable CONFIG_FS_POSIX_ACL.
Right now, when you enable CONFIG_FS_POSIX_ACL it will enable
CONFIG_BTRFS_FS_POSIX_ACL, but it will be disabled once you install
kmod-btrfs. This should prevent it.
Btrfs has enabled by default ACL for mount option.
More details:
https://cateee.net/lkddb/web-lkddb/BTRFS_FS_POSIX_ACL.htmlhttps://btrfs.wiki.kernel.org/index.php/Manpage/btrfs(5)
Signed-off-by: Josef Schlehofer <josef.schlehofer@nic.cz>
71e08471ab56 mt76: eeprom: fix return code on corrected bit-flips
9a8fc6636d83 mt76: move sar_capa configuration in common code
7cdbea1dc82a mt76: only access ieee80211_hdr after mt76_insert_ccmp_hdr
678071ef7029 mt76: mt7615: clear mcu error interrupt status on mt7663
Signed-off-by: Felix Fietkau <nbd@nbd.name>
a6451fea5a3d mt76: mt7615: improve wmm index allocation
1911486414dc mt76: mt7915: improve wmm index allocation
7998a41d1321 mt76: clear sta powersave flag after notifying driver
664475574438 mt76: mt7603: introduce SAR support
5c0da39c940b mt76: mt7915: introduce SAR support
77fc6c439a32 mt76: mt7603: improve reliability of tx powersave filtering
094b3d800835 firmware: update mt7663 rebb firmware to 20200904171623
25237b19bcc1 mt76: eeprom: tolerate corrected bit-flips
1463cb4c6ac2 mt76: mt7921: fix boolreturn.cocci warning
586bad6020f7 mt76: mt7921: use correct iftype data on 6GHz cap init
8ec95c910425 mt76: mt7921s: fix bus hang with wrong privilege
688e30c7d854 firmware: update mt7921 firmware to version 20211014
6fad970893dd mt76: fix key pointer overwrite in mt7921s_write_txwi/mt7663_usb_sdio_write_txwi
95acf972750c mt76: fix 802.3 RX fail by hdr_trans
3f402b0cf6c0 mt76: mt7921s: fix possible kernel crash due to invalid Rx count
929a03a8d65d mt76: connac: fix last_chan configuration in mt76_connac_mcu_rate_txpower_band
Signed-off-by: Felix Fietkau <nbd@nbd.name>
When compiling with CONFIG_USE_RFKILL=y, the build fails and mentions that
dependency on kmod-rfkill is missing, which is correct [1]. Add this
dependency to the Makefile.
Depend on +USE_RFKILL and not PACKAGE_kmod-rfkill, because it forces
selection of kmod-rfkill package. Other combinations in DEPENDS like
USE_RFKILL:kmod-rfkill or (+)PACKAGE_kmod-rfkill:kmod-rfkill do not force
selection of kmod-rfkill package.
The kmod-rfkill package itself depends on USE_RFKILL, so with +USE_RFKILL
in kmod-cfg80211 package it is not possible to select wrong combination of
packages.
[1] https://linux-wireless.vger.kernel.narkive.com/m8JY9Iks/cfg80211-depends-on-rfkill-or-not
Signed-off-by: Oldřich Jedlička <oldium.pro@gmail.com>
If spectral scan support is enabled then ath10k-ct will cause a NULL
pointer due to relay_open() being called with a const callback struct
which is only supported in kernel 5.11 and later.
So, simply check the kernel version and if 5.11 and newer use the const
callback struct, otherwise use the regular struct.
Fixes: 553a3ac ("ath10k-ct: use 5.15 version")
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add back support for the TLC591xx series LEDs which are used in the
ipq806x-based Meraki Cryptid series devices.
This module previously existed for the mvebu platform but was removed
at commit f849c2c832 due to being enabled
in that platform's kernel config.
Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
Update ath10k-ct to get the upstream fix for
DFS support for VHT160 in the 5.15 based ath10k-ct.
(Switch from 5.10 to 5.15 surfaced the upstream regression.)
* refresh one patch
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
We switched to mac80211 5.15 backport version.
Also switch ath10k-ct to 5.15 and drop the mac address patch
that got merged upstream.
Compile and tested on ipq806x Netgear R7800.
Also update the ath10k-ct to latest version to fix a typo
for the new version in the kernel log.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Some drivers that do their own sequence number allocation (e.g. ath9k, mwlwifi) rely
on being able to modify params->ssn on starting tx ampdu sessions.
This was broken by a change that modified it to use sta->tid_seq[tid] instead.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
