The list of v2/v3 devices is getting longer and makes reading the names of
the profiles unnecessary hard.
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
Fixes the following issue:
root@LEDE:/# sysupgrade /tmp/lede-mvebu-armada-388-clearfog-sdcard.img.gz
Saving metaconfig...
Image metadata not found
Use sysupgrade -F to override this check when downgrading or flashing to vendor firmware
Image check 'fwtool_check_image' failed.
root@LEDE:/#
Acked-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
The firmware hotplug script tries to read the mac address from a
partition with the name "uboot-env" which does not exist (instead it's
name is uboot_env). This broke calculation of the new checksum (after
patching the mac address) which resulted in ath9k refusing to use the
EEPROM data.
The original error reported by ath9k was:
PCI: Enabling device 0000:00:0e.0 (0000 -> 0002)
ath: phy0: Bad EEPROM checksum 0x2523
ath: phy0: Unable to initialize hardware; initialization status: -22
ath9k 0000:00:0e.0: Failed to initialize device
Fixes: a20616863d ("lantiq: use ath9k device tree bindings
binding/owl-loader")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
platform_find_rootfspart() fails if the kernel partition comes before the
rootfs partition. The proposed patch fixes this while preserving what I
understand was the original idea: stop at first match.
Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
Upstream linux commit 7523e4dc5057e "module: use a structure to
encapsulate layout." moves some of the struct module members into a
separate struct module_layout.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Do not put the probe function into the __init section, but use the normal
section. This fixes a section mismatch warning.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The following patches were dropped because they are already applied
upstream:
0012-pinctrl-lantiq-fix-up-pinmux.patch
0013-MTD-lantiq-xway-fix-invalid-operator.patch
0014-MTD-lantiq-xway-the-latched-command-should-be-persis.patch
0015-MTD-lantiq-xway-remove-endless-loop.patch
0016-MTD-lantiq-xway-add-missing-write_buf-and-read_buf-t.patch
0017-MTD-xway-fix-nand-locking.patch
0044-pinctrl-lantiq-introduce-new-dedicated-devicetree-bi.patch
0045-pinctrl-lantiq-Fix-GPIO-Setup-of-GPIO-Port3.patch
0046-pinctrl-lantiq-2-pins-have-the-wrong-mux-list.patch
0047-irq-fixes.patch
0047-mtd-plat-nand-pass-of-node.patch
0060-usb-dwc2-Add-support-for-Lantiq-ARX-and-XRX-SoCs.patch
0120-MIPS-lantiq-add-support-for-device-tree-file-from-bo.patch
0121-MIPS-lantiq-make-it-possible-to-build-in-no-device-t.patch
122-MIPS-store-the-appended-dtb-address-in-a-variable.patch
The PHY driver was reduced to the code adding the LED configuration,
the rest is already upstream:
0023-NET-PHY-adds-driver-for-lantiq-PHY11G.patch
The SPI driver was replaced with the version pending for upstream
inclusion:
New driver:
0090-spi-add-transfer_status-callback.patch
0091-spi-lantiq-ssc-add-support-for-Lantiq-SSC-SPI-controller.patch
Old driver:
0100-spi-add-support-for-Lantiq-SPI-controller.patch
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This patch add ZyXEL NSA325 2-Bay Media Server
The ZyXEL NSA325 device is a Kirkwood based NAS:
- SoC: Marvell 88F6702 1600Mhz
- SDRAM memory: 512MB DDR2 400Mhz
- Gigabit ethernet: Marvell Alaska
- Flash memory: 128MB
- 1 Power button
- 1 Power LED (blue)
- 5 Status LED (green/red)
- 1 Copy/Sync button
- 1 Reset button
- 2 SATA II ports (internal)
- 2 USB 2.0 ports (back)
- 1 USB 3.0 port (front)
- Fan (fixed speed)
- hardware watchdog in a mcu
Basically a bigger, more powerful version of NSA310,
installation is the same as they share the same flash layout.
A notable difference is that there is a hardware watchdog
in a mcu on the board, which is disabled by default in the LEDE u-boot.
The watchdog is also disabled with a GPIO activation through
raw register change when kwbooting or it would reset the board before
the new uboot was transferred.
Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
Signed-off-by: Felix Fietkau <nbd@nbd.name> [remove dead code]
switch nsa310b mac address reading to mtd_get_mac_ascii helper as
it seems the fw_env.config file is created way later than when
network is set up, when I tested I still had that file included
in the image through /files folder.
Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
When we merged all the Geode boards into one generic target, the default
network and LED configuration was lost. Put it back.
Fixes: 9e0759ea26 ("x86: merge all geode based subtargets into one")
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Adds preliminary kernel 4.9 support for this target.
- Refreshed/Updated all patches
Added 3 new patches:
- 093 --> Add virtual PCI MMIO mapping
- 230 --> Remove deprecated code
- 240 --> Rework AT24 eeprom code to use the new NVMEM API
Compiled & tested on cns3xxx (gw2388)
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Add support for the Observa Telecom VH4032N router.
This is another BCM6368 router, 128 MB RAM, 32MB flash and 3 USB
host ports.
The wifi chip is an onboard Broadcom BCM43222.
Signed-off-by: Daniel Gonzalez Cabanelas <dgcbueu@gmail.com>
[jonas.gorski: use gpio-hog instead of abusing ephy-reset]
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Remove CONFIG_VLAN_8021Q overrides for two targets
These features are built into the kernel image for all targets
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Probe the switch through DT instead of a platform device. This fixes
probe, as GPIO offsets are now properly accounted for.
Fixes the following issue:
[ 0.802953] 8021q: 802.1Q VLAN Support v1.8
[ 0.810518] rtl8366_smi: gpio_request failed for 18, err=-517
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
BCM6362 and BCM3380 seem to share the same PRID. Disable serial output
for them until we can find a way to tell them apart reliably.
Fixes: 8f3cfe4ba2 ("brcm63xx: lzma-loader: add BCM3380 support")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
This patch adds support for the ADB P.DG AV4202N aka Pirelli PRG AV4202N.
Signed-off-by: Paul Wassi <p.wassi@gmx.at>
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Add support for mapping some GPIO lines to IRQs. GPIO to IRQ mappings
were found out through experimentation, helped by having the GPIO as
output still toggling the IRQ input.
Based-on: http://patchwork.ozlabs.org/patch/660534/
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Setting the clear bit for an interrupt seems to cause interrupts to be
deasserted again immediately. So unset the bit for BCM6318 to allow
subsequent interrupts to still work.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Default CONSOLE value for ar71xx target is "ttyS0,115200", so there
is no need to specify the same value in device profiles.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
This commit reverts 42f3c1f ("arc770: fix broken upstream change")
and simultaneously adds back-ported fix from Linus' tree:
a524c218bc94 ("ARC: [arcompact] brown paper bag bug in unaligned
access delay slot fixup").
Note mentioned patch will appear in stable trees soon as well so
IMHO there's not much sense in adding this separate patch in lede/master branch.
As well as we will get rid of it here in 17.01 once we bump 4.4 kernel here
later down the line.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Felix Fietkau <nbd@nbd.name>
Cc: John Crispin <john@phrozen.org>
Cc: Jo-Philipp Wich <jo@mein.io>
mtdsplit_lzma requires that the rootfs be aligned to a block boundary.
Pad the kernel partition to make this so.
Signed-off-by: Claudio Leite <leitec@gmail.com>
buildbot fails to build without regmap, which I couldn't reproduce locally.
Hopefully this fixes it.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
64 bit support for Raspberry Pi 3 is experimental. However, bcm2709 subtarget
should serve as a stable and compatible 32 bit support.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
This adds support for Raspberry Pi 3 on the bcm2709 subtarget, in order to
keep 32 bit image support when 64 bit support is added on bcm2710 subtarget.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Initial idea was to use package with this PHY driver for devices that
need it. Unfortunately this can't work as bgmac is built-in and PHY
probing happens before loading modules - it results in PHY subsystem
picking default (generic) PHY driver.
There were two ways of solving this:
1) Making bcm53xx use bgmac as module
xor
2) Built-in Broadcom PHY driver
After some quick discussion it seems we can simply built-in the driver
as increased kenel size is relatively small (1805 B).
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
These are patches queued for 4.11. It adds support for even more hw and
removes some annoying WARN_ONCE.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
It's needed for macaddr_add.
Fixes: 50efd403e6 ("bcm53xx: set WAN MAC address to don't share one with LAN interface")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
After "73d923e base-files: emit tagged switch configuration by default"
some default network configurations are broken because the lan and wan
ifnames are forcibly set to untagged netdevs.
Adjust the offending set_interfaces_lan_wan() calls to use the proper
tagged device names.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
It just makes code consistent. This trivial change may be a 17.01
candidate to provide simpler backporting experience.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
In kernel 4.9 it's already present so we don't want to overwite it (with
older & API incompatible version).
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Refresh patches for all targets that support kernel 4.4.
Compile-tested on all targets that use kernel 4.4 and aren't marked
broken, except arc770 and arch38 due to broken toolchain.
Runtime-tested on ar71xx, octeon, ramips and x86/64.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
The Sanlinking Technologies D240
(http://www.sanlinking.com/en/29-dual-4g-wifi-router.html) is basically the same
device as the ZBT WE826, so adding support for it in LEDE is straight forward.
The differences is that the D240 has two mini-PCIe slots (instead of one), blue
LEDs and supports PoE.
Specification:
* CPU: MT7620A
* 1x 10/100Mbps POE (802.3af/802.3at) Ethernet, 4x 10/100Mbps.
* 16 MB Flash.
* 128 MB RAM.
* 1x USB 2.0 port.
* 2x mini-PCIe slots.
* 2x SIM slots.
* 1x 2.4Ghz WIFI.
* 1x button.
Wifi, USB, switch and both mini-PCIe slots are working. I have not been able to
test the SD card reader.
The device comes pre-installed with an older version of OpenWRT, including Luci.
In order to install LEDE, you need to follow the existing procedure for updating
OpenWRT/LEDE using Luci. I.e., you need to access the UI and update the firmware
using the sysupgrade-image. Remember to select that you do not want to keep
existing settings. The default router address is 192.168.10.1 and
username/password admin/root (at least on my devices).
If you brick the device, the procedure for recovery is the same as for the
WE826. Please see the wiki page for that device for instructions.
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
This patch moves the fakeroot code required by some devices to
`image-commands.mk`.
Create the fakeroot on the fly by using the undocumented -s (skip copy)
parameter of mkimage.
Signed-off-by: Joseph C. Lehner <joseph.c.lehner@gmail.com>
[remove unused NETGEAR_KERNEL_MAGIC, remove workarounds to have a dummy
rootfs for mkimage]
Signed-off-by: Mathias Kresin <dev@kresin.me>
The factory image can't be bigger than 3328 KByte. If the image is
bigger than that, the gemtek-header tool throws an error and breaks
the build.
Make sure the output file to which the gemtek header should be added
exists and wasn't removed during the check-size step because of it
size. This will prevent hard errors in case the factory image is to big
similar to what is done for sysupgrade images.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Commit 71a39b8 ("ipq806x: Fix wireless support for Netgear Nighthawk X4S
D7800") added a trailing TAB char after the backslash which prevents
the assignment of the correct MACs for wifi devices.
Fixes: FS#451
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
[reworded commit message]
Signed-off-by: Mathias Kresin <dev@kresin.me>
After analyzing numerous NVRAMs and vendor firmwares it seems the base
MAC address is used for LAN interface. WAN interface has different one
which sometimes is set directly in NVRAM and sometines needs to be
calculated.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Added the missing audio pcm interface in the .dtsi file for the rt5350
device. The update has been verified from the data get from the datasheet
and is very similar to the mt7620a.dtsi
Signed-off-by: Giuseppe Lippolis <giu.lippolis@gmail.com>
Use a vendor prefix as it has to be for all not core driver. Update the
compatible string in the device tree files accordingly.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The comptible string is neither added by any LEDE patch nor exists in
in the kernel. Drop the sound node which was obviously added
accidentally with 9195d8da ("ramips: DTS rework").
Signed-off-by: Mathias Kresin <dev@kresin.me>
Use only the jedec,spi-nor compatible string. Everything else either
never worked or is only support to keep compatibility.
Remove the linux,modalias property. It is obsolete since kernel 4.4.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The setting mmc-ddr-1_8v in the platform dts leads to read errors. The
device is unusable and system reboots in a loop. Because NBG6817 is the
only mmc device, I removed it in base dts.
The second change removes settings now present in base dts.
The third change references was a wrong conversion of constants in the switch settings.
Switch now initializes again.
Signed-off-by: André Valentin <avalentin@marcant.net>
Refreshed patches for all supported targets.
Compile-tested on ar71xx, cns3xxx, imx6, mt7621, oxnas and x86/64.
Run-tested on ar71xx, cns3xxx, imx6 and mt7621.
Tested-by: Stijn Segers <francesco.borromini@inventati.org>
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
This activates the CONFIG_MIPS_APPENDED_RAW_DTB kernel configuration and
configures the F5D8235 V1 target to use append-dtb for kernel creation
instead of OWRTDTB.
Signed-off-by: Tobias Wolf <github-NTEO@vplace.de>
[Jo-Philipp Wich: rewrap commit message]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
This commit introduces CONFIG_MIPS_APPENDED_RAW_DTB as an alternative to
OWRTDTB. Both solutions can be used concurrently until all board
configurations have been changed.
Signed-off-by: Tobias Wolf <github-NTEO@vplace.de>
[Jo-Philipp Wich: rewrap commit message]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
In order to prepare support for generating tagged switch configurations by
default, explicitely request untagged configs for boards which do not already
request tagging to retain default behaviour.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Use silent make invocations for sub-makes like build_image or checksum to
avoid bloating the IB output with non-status info.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Uses upstream code to parse DT supported band/frequency information.
Update existing .dts files to the new format and remove unnecessary
overrides.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
We override default Ethernet interface with eth0 which often uses random
MAC due to missing proper NVRAM entry. Fix this by manually assigning
MAC in the config.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
All mvebu boards have three USB LEDs. The first one is used for the
USB1 port.
There are two LEDs related to the second USB port. The top (bar) LED
gets bright in case any USB device is connected to the second USB port.
If the connected device is an USB 3 (SuperSpeed) device, the small dot
LED bellow the "bar" LED gets also bright.
While at it, use a name for the USB LEDs that matches the names printed
on the case.
Fixes: FS#423, FS#425
Signed-off-by: Kabuli Chana <newtownbuild@gmail.com>
Signed-off-by: Mathias Kresin <dev@kresin.me>
This is a pure rename without any changes. It makes maintaining bgmac
simpler and will hopefully make adding new kernel a bit easier.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Buffalo WCR-1166DS is a small wireless router with
- MT7628AN + MT7612E
- 64MiB DDR2 SDRAM
- 16MiB SPI flash
- 2T2R 11ac/a/b/g/n Wi-Fi
- 2x 10/100M ethernet switch
- 8x programmable LED
- 3x button
- UART pad on PCB (J2: 3.3V, GND, TX, RX)
factory image can be installed via stock web UI.
due to the "dual image" function in the bootloader, the second half of
the SPI flash ("firmware2" partition) cannot be used as a part of the
file system.
Signed-off-by: FUKAUMI Naoki <naobsd@gmail.com>
only factory images for DHP-EU and DHP2-JP (fw ver. 2.x) are built.
this will not work for DHP-JP/AP/TW (fw ver. 1.x) because they use
different buffalo_csum() formula.
Signed-off-by: FUKAUMI Naoki <naobsd@gmail.com>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This fixes logic bug(in function netdev_trig_notify) introduced in
0b2991a8ed commit.
Events triggered by different interfaces were stopping work queue so it
wasn't working for tx/rx mode.
Signed-off-by: Sergey Sergeev <adron@yapic.net>
Commit 29443e2 (mxs: remove modules.mk, select drivers in the kernel config)
missed to remove these references, so cleanup it now.
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
The VGV7510KW22BRN and VGV7519BRN do not have the same brnImage
signature. It was accidentally changed with ba42c1d ("lantiq: un-macro
the image building code").
Signed-off-by: Mathias Kresin <dev@kresin.me>
This reverts commit e79ecb4c26.
The commit was incomplete and the issue that should be fixed isn't
that easy fixable. The Archer C7 mach file is used for the Archer C5,
WDR4900 and WDR7500 as well. Where the WDRs in compare to the Archer
do have blue LEDs.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Do not put the apex images into the kernel build directory as this directory
might get removed after kernel updates while the apex packages InstallDev
recipe is not getting re-executed because it is still considered current,
leading to image build failures later on due to missing images.
To ensure that built bootloader images persist over kernel version updates in
the buildroot, put them into the new STAGING_DIR_IMAGE directory.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Do not put the u-boot images into the kernel build directory as this directory
might get removed after kernel updates while the u-boot packages InstallDev
recipe is not getting re-executed because it is still considered current,
leading to image build failures later on due to missing images.
To ensure that built bootloader images persist over kernel version updates in
the buildroot, put them into the new STAGING_DIR_IMAGE directory.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Do not put the u-boot images into the kernel build directory as this directory
might get removed after kernel updates while the u-boot packages InstallDev
recipe is not getting re-executed because it is still considered current,
leading to image build failures later on due to missing images.
To ensure that built bootloader images persist over kernel version updates in
the buildroot, put them into the new STAGING_DIR_IMAGE directory.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Do not put the u-boot images into the kernel build directory as this directory
might get removed after kernel updates while the u-boot packages InstallDev
recipe is not getting re-executed because it is still considered current,
leading to image build failures later on due to missing images.
To ensure that built bootloader images persist over kernel version updates in
the buildroot, put them into the new STAGING_DIR_IMAGE directory.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Do not put the u-boot and ucode images into the kernel build directory as this
directory might get removed after kernel updates while the u-boot packages
InstallDev recipe is not getting re-executed because it is still considered
current, leading to image build failures later on due to missing images.
To ensure that built bootloader images persist over kernel version updates in
the buildroot, put them into the new STAGING_DIR_IMAGE directory.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Do not put the u-boot images into the kernel build directory as this directory
might get removed after kernel updates while the u-boot packages InstallDev
recipe is not getting re-executed because it is still considered current,
leading to image build failures later on due to missing u-boot images.
To ensure that built bootloader images persist over kernel version updates in
the buildroot, put them into the new STAGING_DIR_IMAGE directory.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Introduce a new location STAGING_DIR_IMAGE which is intended to be used by
bootloader iamges and similar image-related artifacts.
This directory is guaranteed to be persistent across kernel upgrades which
might involve a removal of KERNEL_BUILD_DIR and is guranteed to be bundled
with the image builder.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
