This fixes problem of overwriting BCM4908 U-Boot and DTB files by
BCM4912 ones. That bug didn't allow booting BCM4908 devices.
Fixes: f4c2dab544 ("uboot-bcm4908: add BCM4912 build")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
The change of the PKG_VERSION caused the hash of the package to
change. This is because the PKG_VERSION is present in the
internal directory structure of the archive.
Fixes: e879cccaa2 ("uboot-layerscape: update PKG_HASH")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Hardware
--------
CPU: Mediatek MT7621
RAM: 256M DDR3
FLASH: 128M NAND
ETH: 1x Gigabit Ethernet
WiFi: Mediatek MT7915 (2.4/5GHz 802.11ax 2x2 DBDC)
BTN: 1x Reset (NWA50AX only)
LED: 1x Multi-Color (NWA50AX only)
UART Console
------------
NWA50AX:
Available below the rubber cover next to the ethernet port.
NWA55AXE:
Available on the board when disassembling the device.
Settings: 115200 8N1
Layout:
<12V> <LAN> GND-RX-TX-VCC
Logic-Level is 3V3. Don't connect VCC to your UART adapter!
Installation Web-UI
-------------------
Upload the Factory image using the devices Web-Interface.
As the device uses a dual-image partition layout, OpenWrt can only
installed on Slot A. This requires the current active image prior
flashing the device to be on Slot B.
If the currently installed image is started from Slot A, the device will
flash OpenWrt to Slot B. OpenWrt will panic upon first boot in this case
and the device will return to the ZyXEL firmware upon next boot.
If this happens, first install a ZyXEL firmware upgrade of any version
and install OpenWrt after that.
Installation TFTP
-----------------
This installation routine is especially useful in case
* unknown device password (NWA55AXE lacks reset button)
* bricked device
Attach to the UART console header of the device. Interrupt the boot
procedure by pressing Enter.
The bootloader has a reduced command-set available from CLI, but more
commands can be executed by abusing the atns command.
Boot a OpenWrt initramfs image available on a TFTP server at
192.168.1.66. Rename the image to owrt.bin
$ atnf owrt.bin
$ atna 192.168.1.88
$ atns "192.168.1.66; tftpboot; bootm"
Upon booting, set the booted image to the correct slot:
$ zyxel-bootconfig /dev/mtd10 get-status
$ zyxel-bootconfig /dev/mtd10 set-image-status 0 valid
$ zyxel-bootconfig /dev/mtd10 set-active-image 0
Copy the OpenWrt ramboot-factory image to the device using scp.
Write the factory image to NAND and reboot the device.
$ mtd write ramboot-factory.bin firmware
$ reboot
Signed-off-by: David Bauer <mail@david-bauer.net>
The armvirt target is also used to run OpenWrt in lxc on other targets
like a Raspberry Pi. If we set WOLFSSL_HAS_CPU_CRYPTO by default the
wolfssl binray is only working when the CPU supports the hardware crypto
extension.
Some targets like the Raspberry Pi do not support the ARM CPU crypto
extension, compile wolfssl without it by default. It is still possible
to activate it in custom builds.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This adds a simple AES-128-CBC encryption/decryption program using
either wolfSSL or OpenSSL as backend to decrypt Arcadyan WG4xx223
configuration partitions. The ipk size is 3,355 bytes.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
The system parameters are contained in the Bdata partition.
To use the fw_setsys command, you need to create a file
fw_sys.config.
This file is created after calling the functions
ubootenv_add_uci_sys_config and ubootenv_add_app_config.
Signed-off-by: Oleg S <remittor@gmail.com>
[ wrapped commit description to 72 char ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Now that libiconv-stub is gone, a replacement for its host build is
needed.
Fixes: c0ba4201f8 ("libiconv-stub: remove")
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
moves and extends the current facilities, which have been
added some time ago for the the usbip utility, to support
more utilites that are shipped with the Linux kernel tree
to the SDK.
this allows to drop all the hand-waving and code for
failed previous attempts to mitigate the SDK build failures.
Fixes: bdaaf66e28 ("utils/spidev_test: build package directly from Linux")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Accessing the console on many devices is difficult.
netconsole eases debugging on devices that crash
after the network is up.
Reference to the netconsole documentation in upstream Linux:
<https://www.kernel.org/doc/html/latest/networking/netconsole.html>
|
|netconsole=[+][src-port]@[src-ip]/[<dev>],[tgt-port]@<tgt-ip>/[tgt-macaddr]
|
| where
| + if present, enable extended console support
| src-port source for UDP packets (defaults to 6665)
| src-ip source IP to use (interface address)
| dev network interface (eth0)
| tgt-port port for logging agent (6666)
| tgt-ip IP address for logging agent
| tgt-macaddr ethernet MAC address for logging agent (broadcast)
OpenWrt specific notes:
OpenWrt's device userspace scripts are attaching the network
interface (i.e. eth0) to a (virtual) bridge (br-lan) device.
This will cause netconsole to report:
|network logging stopped on interface eth0 as it is joining a master device
(and unfortunately the traffic/logs to stop at this point)
As a workaround, the netconsole module can be manually loaded
again after the bridge has been setup with:
insmod netconsole netconsole=@/br-lan,@192.168.1.x/MA:C...
One way of catching errors before the handoff, try to
append the /etc/modules.conf file with the following extra line:
options netconsole netconsole=@/eth0,@192.168.1.x/MA:C...
and install the kmod-netconsole (=y) into the base image.
Signed-off-by: Catalin Toda <catalinii@yahoo.com>
(Added commit message from PR, added links to documentation)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The change of the PKG_VERSION caused the hash of the package to
change. This is because the PKG_VERSION is present in the
internal directory structure of the uboot-layerscape-21.08.tar.xz
archive.
i.e:
# tar tf uboot-layerscape-21.08.tar.xz:
uboot-layerscape-21.08/
uboot-layerscape-21.08/.azure-pipelines.yml
uboot-layerscape-21.08/.checkpatch.conf
uboot-layerscape-21.08/.gitattributes
uboot-layerscape-21.08/.github/
[...]
vs.
# tar tf uboot-layerscape-LSDK-21.08.tar.xz
uboot-layerscape-LSDK-21.08/
uboot-layerscape-LSDK-21.08/.azure-pipelines.yml
uboot-layerscape-LSDK-21.08/.checkpatch.conf
uboot-layerscape-LSDK-21.08/.gitattributes
uboot-layerscape-LSDK-21.08/.github/
[...]
the (file) content of both archives are otherwise the same.
The PKG_HASH was taken from the builder log:
| Hash of the local file uboot-layerscape-21.08.tar.xz does not match
|(file: 54909a98bdcc26c7f9b35b35fcae09b977ecbf044be7bffa6dad9306c47cccf6,
|requested: 874e871755ef84ebbf3[...]) - deleting download.
without this update, the uboot-layerscape-21.08 package would
always try to download (from git), repacked the archive and
reupload to sources.openwrt.org (~14 MiB saved).
Fixes: 038d5bdab1 ("layerscape: use semantic versions for LSDK")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
those board files can/should be dropped now too.
Fixes: 50c232d6f4 ("ipq-wifi: drop upstreamed board-2.bin")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
the tacked on @TARGET_bcm53xx causes warnings:
tmp/.config-package.in:14027:warning: ignoring unsupported character '@'
tmp/.config-package.in:26028:warning: ignoring unsupported character '@'
this was wrong.
Fixes: be1761fa14 ("nu801: add MR26 to the table")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
ef5d3e3 jail: fix various ignoring return value compilation warning
8e4a956 jail: add WARNING macro to log non critical warning message
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
46a33b8 kmodloader: fix compilation warning with not checking return of asprintf
Also switch PKG_RELEASE to AUTORELEASE.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
This version fixes two vulnerabilities:
-CVE-2022-34293[high]: Potential for DTLS DoS attack
-[medium]: Ciphertext side channel attack on ECC and DH operations.
The patch fixing x86 aesni build has been merged upstream.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
the legacy driver was dropped in linux 5.14-rc3:
commit d249ff28b1d8 ("intersil: remove obsolete prism54 wireless driver")
Quoting Lukas Bulwahn:
"p54 replaces prism54 so users should be unaffected."
Reported-by: Marius Dinu <m95d+git@psihoexpert.ro>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The spidev_test is build in phase2 even though it should be disabled.
My best guess is that we hit the same issue that I had with nu801.
The build-system thinks it's a tool that is necessary for
building the kernel.
In this case, the same fix (adding a dependency on the presence of
the module) could work in this case as well?
Fixes: bdaaf66e28 ("utils/spidev_test: build package directly from Linux")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The BDFs for the:
GL.iNet GL-B2200
were upstreamed to the ath10k-firmware repository
and landed in linux-firmware.git
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Kalle:
"I see that variant has a space in it, does that work it correctly? My
original idea was that spaces would not be allowed, but didn't realise
to add a check for that."
Is this an easy change? Because the original author (Tim Davis) noted:
"You may substitute the & and space with something else saner if they
prove to be problematic."
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This PR allows a user to enable a private psk, where each station
may have it's own psk or use a common psk if it is not defined.
The private psk is defined using the sta's mac and a radius server
is required.
ppsk option should be enabled in the wireless configuration along with
radius server details. When using PPSK, the key is ignored, it will be
retrieved from radius server. SAE is not yet supported (private sae) in
hostapd.
Wireless example configuration:
option encryption 'psk2+ccmp'
option ppsk '1'
option auth_server '127.0.0.1'
option auth_secret 'radiusServerPassword'
If you want to use dynamic VLAN on PPSK also include:
option dynamic_vlan '2'
option vlan_tagged_interface 'eth0'
option vlan_bridge 'br-vlan'
option vlan_naming '0'
It works enabling mac address verification on radius server and
requiring the tunnel-password (the private psk) from radius server.
In the radius server we need to configure the users. In case of
freeradius: /etc/freeradius3/mods-config/files/authorize
The user and Cleartext-Password should be the mac lower case using the
format "aabbccddeeff"
<sta mac> Cleartext-Password := "<sta mac>"
Tunnel-Password = <Private Password>
Example of a user configured in radius and using dynamic VLAN5:
8cb84a000000 Cleartext-Password := "8cb84a000000"
Tunnel-Type = VLAN,
Tunnel-Medium-Type = IEEE-802,
Tunnel-Private-Group-ID = 5,
Tunnel-Password = MyPrivPw
If we want to have a default or shared psk, used when the mac is not
found in the list, we need to add the following at the end of the radius
authorize file:
DEFAULT Auth-Type := Accept
Tunnel-Password = SharedPw
And if using VLANs, for example VLAN6 for default users:
DEFAULT Auth-Type := Accept
Tunnel-Type = VLAN,
Tunnel-Medium-Type = IEEE-802,
Tunnel-Private-Group-ID = 6,
Tunnel-Password = SharedPw
Signed-off-by: Manuel Giganto <mgigantoregistros@gmail.com>
the hash and timestamp of the remote copy of the archive
has changed since last bump
meaning the remote archive copy was recreated
Signed-off-by: Michael Pratt <mcpratt@pm.me>
swig has been installed on the buildbots a while a ago and
Petr Štetiar got a fix for the pylibfdt error. Use that and re-enable
the builds for mt7620 and mt7621.
Refresh patches while at it.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Let U-Boot handle free space in UBI partitions by recognizing the EOF
marker OpenWrt is using as well for that purpose.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Buidbots are throwing the following compile error:
In file included from tools/aisimage.c:9:
include/image.h:1133:12: fatal error: openssl/evp.h: No such file or directory
^~~~~~~~~~~~~~~
compilation terminated.
Fix it by passing `UBOOT_MAKE_FLAGS` variable to make.
Suggested-by: Petr Štetiar <ynezz@true.cz>
Fixes: 6d5611af28 ("uboot-at91: update to linux4sam-2022.04")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Building U-Boot for the MT7621 SoC requires binman, a Python-based
host tool to generate images. For now, binman cannot work inside the
OpenWrt build system because it requires swig, so mark the MT7621
boards as borken to fix the ramips/mt7621 build until someone with
knowledge about Python and swig fixes the underlaying issue.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Buidbots are currently choking on the following compile error:
In file included from tools/aisimage.c:9:
include/image.h:1133:12: fatal error: openssl/evp.h: No such file or directory
# include <openssl/evp.h>
^~~~~~~~~~~~~~~
compilation terminated.
This is caused by a complete overriding of make flags which are provided
correctly in `UBOOT_MAKE_FLAGS` variable, but currently overriden
instead of extended. This then leads to the usage of build host include
dirs, which are not available.
Fix it by extending `UBOOT_MAKE_FLAGS` variable like it was done in
commit 481339a042 ("uboot-imx: fix wrong make flags overriding").
Fixes: 7094e65503 ("uboot-imx: add support for TechNexion PICO-PI-IMX7D")
Signed-off-by: Petr Štetiar <ynezz@true.cz>
* Merge uboot-ramips into uboot-mediatek.
* Port support for the RAVPower RP WD009 to U-Boot 2022.07.
* Add support for MT7621 and add builds for the reference boards.
* Add builds for MT7620 and MT7628 reference boards.
This should help to make development of U-Boot-level board support for
all MediaTek targets much easier.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add patch to fix host-build of the mkimage tool without
CONFIG_TOOLS_LIBCRYPTO.
Update and refresh all patches.
Tested on BananaPi R64 (MT7622) successfully booting from SD card,
eMMC and SPI-NAND.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This board features an AP6335 system-in-package combination of Wi-Fi and
Bluetooth module based on BCM4339.
Support is borrowed directly from the following Buildroot commit:
095420e05ae5: ("configs/imx7dpico: Add Wifi support").
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Old firmware provided by 'cypress-firmware' suite is not sufficient for
AP6335 module used in PICO-PI-IMX7D board to probe successfully. Use the
upstream version from linux-firmware instead.
At the same time, drop the old firmware from 'cypress-firmware' package.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
TechNexion PICO-PI-IMX7D uses BCM4339 Wi-Fi interface in SDIO mode.
Enable SDIO support for imx/cortexa7 to fully support it in images.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Add package supporting Bluetooth HCI interfaces connected over SDIO.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
[pepe2k@gmail.com: dropped rfkill dependency, other minor text fixes]
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
This will allow using fw_printenv without /etc/fw_env.config. Once there
is Linux NVMEM driver available for U-Boot env data.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Update uboot-at91 to linux4sam-2022.04. As linux4sam-2022.04 is based on
U-Boot v2022.01 which contains commit
93b196532254 ("Makefile: Only build dtc if needed") removed also the DTC
variable passed to MAKE to force the compilation of DTC.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Remove upstreamed patches:
- 001-xtables-Call-init_extensions6-for-static-builds.patch
- 002-xtables-Call-init_extensions_a_b.patch
Fix patches:
- 102-iptables-disable-modprobe.patch
Fix warnings in the form of:
xtables.c:475:14: warning: 'get_modprobe' defined but not used [-Wunused-function]
475 | static char *get_modprobe(void)
| ^~~~~~~~~~~~
Backport patches:
- 020-treewide-use-uint-instead-of-u_int.patch
- 030-revert-fix-build-for-missing-ETH_ALEN-definition.patch
- 040-xshared-Fix-build-for-Werror-format-security.patch
- 050-build-fix-error-during-out-of-tree-build.patch
- 060-libxtables-unexport-init_extensions-declarations.patch
Refresh patches:
- 101-remove-check-already.patch
- 102-iptables-disable-modprobe.patch
- 200-configurable_builtin.patch
- 600-shared-libext.patch
- 700-disable-legacy-revisions.patch
Remove from Makefile:
$(CP) $(PKG_BUILD_DIR)/include/libipulog $(1)/usr/include/
Changelog:
fa0ccdbd configure: bump version for 1.8.8 release
8468fd4f nft: Fix EPERM handling for extensions without rev 0
ce9195c6 extensions: LOG: Document --log-macdecode in man page
404f304d man: *NAT: Review --random* option descriptions
0a538259 extensions: DNAT: Merge core printing functions
a7c2b728 libxtables: Revert change to struct xtables_pprot
fd64a587 libxtables: Drop xtables_globals 'optstring' field
3b8a6a6f xshared: Extend xtables_printhelp() for arptables
8ff84eaf xshared: Move arp_opcodes into shared space
adbfec0b extensions: MARK: Drop extra newline at end of help
1dcfb81e nft: split gen_payload() to allocate register and initialize expression
7e38890c nft: prepare for dynamic register allocation
165cafec nft: pass handle to helper functions to build netlink payload
94309632 nft: native mark matching support
aa92ec96 nft: pass struct nft_xt_ctx to parse_meta()
4c70c42f nft-shared: update context register for bitwise expression
18c96821 extensions: man: Document service name support in DNAT and REDIRECT
72d542b6 extensions: Merge REDIRECT into DNAT
14d77c8a extensions: Merge IPv4 and IPv6 DNAT targets
9621318b extensions: DNAT: Rename from libipt to libxt
2e0c9a40 extensions: ipt_DNAT: Combine xlate functions also
7adef314 extensions: ipt_DNAT: Merge v1/v2 print/save code
3f4f1cf0 extensions: ipt_DNAT: Merge v1 and v2 parsers
070a8626 Revert "libipt_[SD]NAT: avoid false error about multiple destinations specified"
08c14fa6 man: DNAT: Describe shifted port range feature
24fff5d7 xlate-test: Fix for empty source line on failure
ac4c84cc libxtables: Boost rule target checks by announcing chain names
f58b0d74 libxtables: Implement notargets hash table
b1aee6b2 nft: Reject standard targets as chain names when restoring
b555bfed tests: shell: Fix 0004-return-codes_0 for static builds
c293e116 nft: Review static extension loading
0836524f xtables: Call init_extensions{,a,b}() for static builds
6c689b63 Simplify static build extension loading
0c8e2535 libxtables: Fix for warning in xtables_ipmask_to_numeric
0c0cd434 nft: Don't pass command state opaque to family ops callbacks
b6196c75 xshared: Prefer xtables_chain_protos lookup over getprotoent
07ee529f nft: Speed up immediate parsing
b5f2faea nft: Simplify immediate parsing
17534cb1 Improve error messages for unsupported extensions
2dbb49d1 libxtables: Register only the highest revision extension
07e2107e xshared: Implement xtables lock timeout using signals
a3980769 tests: NFLOG: enable `--nflog-range` tests
b8e8ac27 tests: support explicit variant test result
adb03c3f tests: add `NOMATCH` test result
7a006c7d tests: iptables-test: rename variable
b7f15b42 iptables.8: Describe the effect of multiple -v flags
1407a9c4 tests: iptables-test: Support variant deviation
fc8f7289 nft: cache: Dump rules if debugging
73b91292 nft: Add debug output to table creation
51d9d9e0 ebtables: Support verbose mode
ad1ed75f nft: Set NFTNL_CHAIN_FAMILY in new chains
17ed253f iptables-restore: Support for extra debug output
a761a026 nft: Use verbose flag to toggle debug output
98e69b7e nft: add support for native tcp flag matching
92808bd5 nft-shared: add tcp flag dissection
6aba94ef nft: prefer native expressions instead of tcp match
c034cf31 nft: prefer native expressions instead of udp match
5489493e nft-shared: support native udp port delinearize
5795a1b5 nft-shared: support native tcp port range delinearize
250dce87 nft-shared: support native tcp port delinearize
ea5d45dc extensions: libxt_NFLOG: fix typo
26ecdf53 xshared: Fix response to unprivileged users
b32ae771 build: replace `AM_PROG_LIBTOOL` and `AC_DISABLE_STATIC` with `LT_INIT`
05286bab extensions: libxt_NFLOG: remove extra space when saving targets with prefixes
f0d02998 extensions: libxt_NFLOG: fix `--nflog-prefix` Python test-cases
f9df828a extensions: libxt_NFLOG: disable `--nflog-range` Python test-cases
62ad29e9 extensions: libxt_NFLOG: don't truncate log prefix on print/save
db99f601 extensions: libxt_NFLOG: use nft built-in logging instead of xt_NFLOG
30b178b9 extensions: *NAT: Kill multiple IPv4 range support
7ee5b970 tests: iptables-test: correct misspelt variable
223f02ca nft: fix indentation error.
5c2c2eea ip6tables: Use the shared do_parse, too
9baf3bf0 iptables: Use xtables' do_parse() function
e4f5185d nft: Move proto_parse and post_parse callbacks to xshared
ded7b579 xshared: Store parsed wait and wait_interval in xtables_args
62c3c93d xshared: Move do_parse to shared space
3039a52c xtables: Do not pass nft_handle to do_parse()
ece001c2 xtables: Pass xtables_args to check_inverse()
17abaeb1 xtables: Pass xtables_args to check_empty_interface()
dc8d8fce xtables: Move struct nft_xt_cmd_parse to xshared.h
98a4462f xtables: Pull table validity check out of do_parse()
d83371c7 xtables: Drop xtables' family on demand feature
49aa44ba nft-shared: set correct register value
b129b1cf iptables-*-restore: Drop pointless line reference
316d8efb libxtables: Extend basic_exit_err()
4bff5aef xtables_globals: Embed variant name in .program_version
51e5d293 xshared: Share exit_tryhelp()
56ac0452 xshared: Share a common printhelp function
4149b5d8 xshared: Share print_match_save() between legacy ip*tables
273d88a7 extensions: tcpmss: add iptables-translate support
7213561d xshared: Make load_proto() static
cf14b92b nft-shared: Drop unused function print_proto()
24f30842 xshared: Share print_header() with legacy iptables
a323c283 xshared: Share print_fragment() with legacy
1d73cec0 xshared: Share print_rule_details() with legacy
e5fb9f8e xshared: Share save_ipv{4,6}_addr() with legacy
22f2e1fc xshared: Share save_rule_details() with legacy
766e4872 xshared: Share print_iface() function
b5881e7f nft: Change whitespace printing in save_rule callback
1189d830 xshared: Merge and share parse_chain()
1eab8e83 extensions: hashlimit: Fix tests with HZ=1000
afa525ee xlate-test: Print full path if testing all files
b8d5271d Unbreak xtables-translate
0af80a91 nft: Merge xtables-arp-standalone.c into xtables-standalone.c
142cf724 xtables: arptables accepts empty interface names
ab0a785a xtables: Derive xtables_globals from family
6cf3976e nft-shared: Make nft_check_xt_legacy() family agnostic
832a0e2b nft-arp: Introduce post_parse callback
0aea399d arptables: Use standard data structures when parsing
fe83b12f libxtables: Introduce xtables_globals print_help callback
0687852d xtables-standalone: Drop version number from init errors
dded8ff3 nft: Add family ops callbacks wrapping different nft_cmd_* functions
38e1fe58 xtables: Simplify addr_mask freeing
cfdda180 nft-shared: Introduce init_cs family ops callback
65b150ae xshared: Store optstring in xtables_globals
2e6014c7 nft: Introduce builtin_tables_lookup()
db90ff64 tests: shell: fix bashism
45d8f769 nft: Delete builtin chains compatibly
e865a853 nft-chain: Introduce base_slot field
f9b33967 nft: Check base-chain compatibility when adding to cache
43189612 nft: cache: Avoid double free of unrecognized base-chains
040a15f2 xtables-translate: add missing argument and option to usage
2ed6dc75 tests: iptables-test: Fix conditional colors on stderr
63ab4fe3 ebtables: Avoid dropping policy when flushing
b714d45d iptables-test.py: print with color escapes only when stdout isatty
481626bb tests: shell: Return non-zero on error
7559af83 tests: iptables-test: Exit non-zero on error
c057939d tests: xlate-test: Exit non-zero on error
a8da7186 tests: iptables-test: Print errors to stderr
5166c445 tests: xlate-test: Print errors to stderr
fa78ff15 tests: xlate-test: Don't skip any input after the first empty line
fcbe454b tests: iptables-test: Fix missing chain case
61e85e31 iptables-nft: allow removal of empty builtin chains
544e7dc1 Fix a few doc typos
e438b976 nft: Use xtables_{m,c}alloc() everywhere
ca11c7b7 nft: Use xtables_malloc() in mnl_err_list_node_add()
cf410aa6 extensions: libxt_mac: Fix for missing space in listing
7ae14dc1 iptables-test: Make netns spawning more robust
bef9dc57 extensions: hashlimit: Fix tests with HZ=100
943fbf3e ip6tables: masquerade: use fully-random so that nft can understand the rule
ef7781eb libxtables: exit if called by setuid executeable
8629c53f tests/shell: Assert non-verbose mode is silent
57d1422d nft: Fix for non-verbose check command
26318637 ebtables: Dump atomic waste
765bf04e doc: ebtables-nft.8: Adjust for missing atomic-options
e727ccad xtables: Call init_extensions6() for static builds
9e1fffdf extensions: libxt_multiport: add translation for -m multiport --ports
c8145139 extensions: libxt_conntrack: simplify translation using negation
1c934617 extensions: libxt_tcp: rework translation to use flags match representation
bb01e33d extensions: libxt_connlimit: add translation
62828a6a tests: xlate-test: support multiline expectation
ba863c4b libxtables: extend xlate infrastructure
68ed965b extensions: libxt_string: Avoid buffer size warning for strncpy()
9b85e1ab libxtables: Introduce xtables_strdup() and use it everywhere
ca840c20 extensions: libebt_ip6: Use xtables_ip6parse_any()
084671d5 iptables-apply: Drop unused variable
0729ab37 nft: Avoid buffer size warnings copying iface names
eab75ed3 nft: Avoid memleak in error path of nft_cmd_new()
ffe88f8f libxtables: Fix memleak in xtopt_parse_hostmask()
8bb5bcae extensions: libebt_ip6: Drop unused variables
97fabae7 libxtables: Drop leftover variable in xtables_numeric_to_ip6addr()
5818be17 extensions: sctp: Translate --chunk-types option
a61282ec extensions: sctp: Fix nftables translation
556f7044 Use proto_to_name() from xshared in more places
eea68ca8 ebtables-translate: Use shared ebt_get_current_chain() function
9dc50b5b xshared: Merge invflags handling code
3664249f xshared: Eliminate iptables_command_state->invert
f647f61f xtables: Make invflags 16bit wide
616800af extensions: SECMARK: Implement revision 1
1e984079 nft-arp: Make use of ipv4_addr_to_string()
acac2dbe Eliminate inet_aton() and inet_ntoa()
9084ef29 extensions: sctp: Explain match types in man page
a3e81c62 nft: Increase BATCH_PAGE_SIZE to support huge rulesets
fdf64dcd nft: cache: Sort chains on demand only
c5d9a723 fix build for missing ETH_ALEN definition
18d7535d extensions: libxt_conntrack: use bitops for status negation
18e334da extensions: libxt_conntrack: use bitops for state negation
831f57c7 libxtables: Simplify xtables_ipmask_to_cidr() a bit
46f9d3a9 xtables-translate: Fix translation of odd netmasks
330f5df0 nft: Fix bitwise expression avoidance detection
5f1fcace iptables-nft: fix -Z option
c9441657 include: Drop libipulog.h
30c1d443 ebtables: Exit gracefully on invalid table names
Signed-off-by: Nick Hainke <vincent@systemli.org>
