Add support for ft_psk_generate_local flag in ieee80211r
Signed-off-by: Lorenzo Santina <lorenzo.santina@edu.unito.it>
[original author]
Signed-off-by: Sergio <mailbox@sergio.spb.ru>
Fix multiple syntax errors in shelscripts (of packages only)
These errors were causing many conditions to not working properly
Signed-off-by: Lorenzo Santina <lorenzo.santina@edu.unito.it>
[increase PKG_RELEASE, drop command substitution from directip.sh]
Signed-off-by: Mathias Kresin <dev@kresin.em>
ifname variable were not assigned due to syntax error
causing the hostapd config file to have an empty iapp_interface= option
Signed-off-by: Lorenzo Santina <lorenzo.santina.dev@gmail.com>
While debugging an issue with a client device, wpa_supplicant did not
seem to log anything at all. Make wpa_supplicant log to syslog instead
of stdout, to make debugging easier and to be consistent with hostapd.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
RADIUS protocol could be used not only for authentication but for
accounting too. Accounting could be configured for any type of networks.
However there is no way to configure NAS Identifier for non-WPA
networks without this patch.
Signed-off-by: Yury Shvedov <yshvedov@wimarksystems.com>
[cleanup commit message]
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
During auto channel selection we may wish to prefer certain channels
over others.
e.g. we can just squeeze 4 channels into europe so '1:0.8 5:0.8 9:0.8
13:0.8' does that.
Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
One of the latest mac80211 updates added sanity checks, requiring the
beacon intervals of all VIFs of the same radio to match. This often broke
AP+11s setups, as these modes use different default intervals, at least in
some configurations (observed on ath9k).
Instead of relying on driver or hostapd defaults, change the scripts to
always explicitly set the beacon interval, defaulting to 100. This also
applies the beacon interval to 11s interfaces, which had been forgotten
before. VIF-specific beacon_int setting is removed from hostapd.sh.
Fixes FS#619.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
None of the variables in this "local" declaration are actually set in
wpa_supplicant_add_network().
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Setting legacy_rates to 0 disables 802.11b data rates.
Setting legacy_rates to 1 enables 802.11b data rates. (Default)
The basic_rate option and supported_rates option are filtered based on this.
The rationale for the change, stronger now than in 2014, can be found in:
https://mentor.ieee.org/802.11/dcn/14/11-14-0099-00-000m-renewing-2-4ghz-band.pptx
The balance of equities between compatibility with b clients and the
detriment to the 2.4 GHz ecosystem as a whole strongly favors disabling b
rates by default.
Signed-off-by: Nick Lowe <nick.lowe@gmail.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name> [cleanup, defaults change]
When sta is configured, hostapd receives 'stop' and 'update' command from
wpa_supplicant. In the update command, hostapd gets sta parameters with
which it configures ap.
Problem is, with the default wireless configuration:
mode:11g freq:2.4GHz channel:1
If sta is connected to 5GHz network, then ap does not work. Ideally with
340-reload_freq_change.patch hostapd should reload the frequency changes
and start ap in 5GHz, but ap becomes invisible in the network.
This issue can be reproduced with following /etc/config/wireless:
config wifi-device radio0
option type mac80211
option channel 1
option hwmode 11g
option path 'virtual/uccp420/uccwlan'
option htmode 'none'
config wifi-iface 'ap'
option device 'radio0'
option encryption 'none'
option mode 'ap'
option network 'ap'
option ssid 'MyTestNet'
option encryption none
config wifi-iface 'sta'
option device radio0
option network sta
option mode sta
option ssid TestNet-5G
option encryption psk2
option key 12345
This change updates current_mode structure based on configured hw_mode
received from wpa_supplicant. Also prepare rates table after frequency
selection.
Signed-off-by: Abhilash Tuse <Abhilash.Tuse@imgtec.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name> [cleanup, patch refresh]
- Fix eap test to work with standalone hostapd builds
- Fix 11n test to check the correct define
- Add 11ac, 11r and 11w tests
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
This will allow starting hostapd with the new -s parameter and finally
read all (error) messages from the syslog.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
It wasn't possible to read hostapd wpa_printf messages unless running
hostapd manually. It was because hostapd was printing them using vprintf
and not directly to the syslog.
We were trying to workaround this problem by redirecting STDIN_FILENO
and STDOUT_FILENO but it was working only for the initialization phase.
As soon as hostapd did os_daemonize our solution stopped working.
Please note despite the subject this change doesn't affect debug level
messages only but just everything printed by hostapd with wpa_printf
including MSG_ERROR-s. This makes it even more important as reading
error messages can be quite useful for debugging.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
ap_setup_locked is named wps_ap_setup_locked in uci for consistency with other
wps related uci options.
Signed-off-by: Steven Honson <steven@honson.id.au>
The hostapd_append_wpa_key_mgmt() procedure uses the possibly uninitialized
$ieee80211r and $ieee80211w variables in a numerical comparisation, leading
to stray "netifd: radio0 (0000): sh: out of range" errors in logread when
WPA-PSK security is enabled.
Ensure that those variables are substituted with a default value in order to
avoid emitting this (harmless) shell error.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
wpa_supplicant allows only SAE as the key management
type for mesh mode. The recent key_mgmt rework unconditionally
added WPA-PSK - this breaks interface bringup and wpa_s
throws this error message:
Line 10: key_mgmt for mesh network should be open or SAE
Line 10: failed to parse network block.
Failed to read or parse configuration '/var/run/wpa_supplicant-wlan0.conf
Fix this by making sure that only SAE is used for mesh.
Signed-off-by: Sujith Manoharan <m.sujith@gmail.com>
Enable support for stronger SHA256-based algorithms in hostapd and
wpa_supplicant when using WPA-EAP or WPA-PSK with 802.11w enabled.
We cannot unconditionally enable it, as it requires hostapd to be
compiled with 802.11w support, which is disabled in the -mini variants.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Tested-by: Sebastian Kemper <sebastian_ml@gmx.net>
Now that wpa_key_mgmt handling for hostapd and wpa_supplicant are
consistent, we can move parts of it to a dedicated function.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Tested-by: Sebastian Kemper <sebastian_ml@gmx.net>
Rework wpa_key_mgmt handling for wpa_supplicant to be consistent with
how it is done for hostapd.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Tested-by: Sebastian Kemper <sebastian_ml@gmx.net>
Update to latest upstream HEAD:
- Refreshed all
- Delete patches and parts which made it upstream
Compile tested Full & Mini configs
Run-tested Mini config
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name> [another update, remove broken patch]
The build system only accepts Package/<name>/description and since the
typoed version virtually has the same content as the TITLE field, remove
them altogether
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
Ensure that selecting the wpa-supplicant-mesh package actually packages the
wpa_supplicant binary with SAE support and add missing dependency on OpenSSL.
Signed-off-by: Alexis Green <alexis@cessp.it>
[Jo-Philipp Wich: slightly reword commit message for clarity]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
This more of a demo for the previous commit that comes with
this one, where I added support for copying source from 'src' to
the build dir(s).
Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
* Change git packages to xz
* Update mirror checksums in packages where they are used
* Change a few source tarballs to xz if available upstream
* Remove unused lines in packages we're touching, requested by jow- and blogic
* We're relying more on xz-utils so add official mirror as primary source, master site as secondary.
* Add SHA256 checksums to multiple git tarball packages
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
RADIUS accounting can be used even when RADIUS authentication is not
used. Move the accounting configuration outside of the EAP-exclusive
sections.
Signed-off-by: Petko Bordjukov <bordjukov@gmail.com>
In company networks everything except the http and https protocol is
often causes problems, because the network administrators try to block
everything else. To make it easier to use LEDE in company networks use
the https/http protocol for git access when possible.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The wpa_supplicant supports an "anonymous_identity" field, which some
EAP networks require. From the documentation:
anonymous_identity: Anonymous identity string for EAP (to be used as the
unencrypted identity with EAP types that support different tunnelled
identity, e.g., EAP-TTLS).
This change modifies the hostapd.sh script to propagate this field
from the UCI config to the wpa_supplicant.conf file.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Reviewed-by: Manuel Munz <freifunk@somakoma.de>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 49181
Introduce config options client_cert2, priv_key2 and priv_key2_pwd
used for EAP-TLS phase2 authentication in WPA-EAP client mode.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 48345
WPA-EAP supports several phase2 (=inner) authentication methods when
using EAP-TTLS, EAP-PEAP or EAP-FAST (the latter is added as a first
step towards the UCI model supporting EAP-FAST by this commit)
The value of the auth config variable was previously expected to be
directly parseable as the content of the 'phase2' option of
wpa_supplicant.
This exposed wpa_supplicant's internals, leaving it to view-level to
set the value properly. Unfortunately, this is currently not the case,
as LuCI currently allows values like 'PAP', 'CHAP', 'MSCHAPV2'.
Users thus probably diverged and set auth to values like
'auth=MSCHAPV2' as a work-around.
This behaviour isn't explicitely documented anywhere and is not quite
intuitive...
The phase2-string is now generated according to $eap_type and $auth,
following the scheme also found in hostap's test-cases:
http://w1.fi/cgit/hostap/tree/tests/hwsim/test_ap_eap.py
The old behaviour is also still supported for the sake of not breaking
existing, working configurations.
Examples:
eap_type auth
'ttls' 'EAP-MSCHAPV2' -> phase2="autheap=MSCHAPV2"
'ttls' 'MSCHAPV2' -> phase2="auth=MSCHAPV2"
'peap' 'EAP-GTC' -> phase2="auth=GTC"
Deprecated syntax supported for compatibility:
'ttls' 'autheap=MSCHAPV2' -> phase2="autheap=MSCHAPV2"
I will suggest a patch to LuCI adding EAP-MSCHAPV2, EAP-GTC, ... to
the list of Authentication methods available.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 48309
In sta-only configuration, wpa_supplicant needs correct regulatory
domain because otherwise it may skip channel of its AP during scan.
Another alternative is to fix "iw reg set" in mac80211 netifd script.
Currently it fails if some phy has private regulatory domain which
matches configured one.
Signed-off-by: Dmitry Ivanov <dima@ubnt.com>
SVN-Revision: 48099
The scripts for authsae and iw use the option mesh_id to get set the
"meshid" during a mesh join. But the script for wpad-mesh ignores the
option mesh_id and instead uses the option ssid. Unify the mesh
configuration and let the wpa_supplicant script also use the mesh_id from
the configuration.
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>
SVN-Revision: 47615
r46861 introduced a new option eapol_version to hostapd, but did not
provide a default value. When the option value is evaluated,
the non-existing value causes errors to the systen log:
"netifd: radio0: sh: out of range"
Add a no-op default value 0 for eapol_version. Only values 1 or 2 are
actually passed on, so 0 will not change the default action in hostapd.
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
SVN-Revision: 47361
One second is not enough for some devices to ackowledge null data frame
which is sent at the end of ap_max_inactivity interval. In particular,
this causes severe Wi-Fi instability with Apple iPhone which may take
up to 3 seconds to respond.
Signed-off-by: Dmitry Ivanov <dima@ubnt.com>
SVN-Revision: 47149
When using FullMAC drivers (e.g. brcmfmac) we don't get mgmt frames so
check for banned client in probe request handler won't ever be used.
Since cfg80211 provides us info about STA associating let's put a check
there.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 47064
Add eapol_version to the openwrt wireless config ssid section.
Only eapol_version=1 and 2 will get passed to hostapd, the default
in hostapd is 2.
This is only useful for really old client devices that don't
accept eapol_version=2.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
SVN-Revision: 46861
As the OpenWrt build system only resolves build dependencies per directory,
all hostapd variants were causing libopenssl to be downloaded and built,
not only wpad-mesh. Fix this by applying the same workaround as in
ustream-ssl.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 46851
Add CONFIG_IEEE80211W variable to DRIVER_MAKEOPTS so that 802.11w
support is properly compiled in full variant.
This fixes#20179
Signed-off-by: Janusz Dziemidowicz <rraptorr@nails.eu.org>
SVN-Revision: 46737
Other VLAN related options are already being processed in netifd.sh
but the vlan_file option is missing. This option allows the mapping
of vlan IDs to network interfaces and will be used in dynamic VLAN
feature for binding stations to interfaces based on VLAN
assignments. The change is done similarly to the wpa_psk_file
option.
Signed-off-by: Gong Cheng <chengg11@yahoo.com>
SVN-Revision: 46652
Add 802.11r client support to wpa_supplicant. It's only enabled in
wpa_supplicant-full. hostapd gained 802.11r support in commit r45051.
Tested on a TP-Link TL-WR710N sta psk client with two 802.11r enabled
openwrt accesspoints (TP-Link TL-WDR3600).
Signed-off-by: Stefan Hellermann <stefan@the2masters.de>
SVN-Revision: 46377
Hostapd's control file location was changed in 2013, and that has apparently
broken the wps button hotplug script in cases where there are multiple radios
and wps is possibly configured also for the second radio. The current wps
button hotplug script always handles only the first radio.
https://dev.openwrt.org/browser/trunk/package/network/services/hostapd/files/wps-hotplug.sh
The reason is that the button hotplug script seeks directories like
/var/run/hostapd*, as the hostapd-phy0.conf files were earlier in
per-interface subdirectories.
Currently the *.conf files are directly in /var/run and the control sockets
are in /var/run/hostapd, but there is no subdirectory for each radio.
root@OpenWrt:/# ls /var/run/hostapd*
/var/run/hostapd-phy0.conf /var/run/hostapd-phy1.conf
/var/run/hostapd:
wlan0 wlan1
The hotplug script was attempted to be fixed after the hostapd change by
r38986 in Dec2013, but that change only unbroke the script for the first
radio, but left it broken for multiple radios.
https://dev.openwrt.org/changeset/38986/
The script fails to find subdirectories with [ -d "$dir" ], and passes just
the only found directory /var/run/hostapd, leading into activating only the
first radio, as hostapd_cli defaults to first socket found inthe passed
directory:
root@OpenWrt:/# hostapd_cli -?
...
usage: hostapd_cli [-p<path>] [-i<ifname>] [-hvB] [-a<path>] \
[-G<ping interval>] [command..]
...
-p<path> path to find control sockets (default: /var/run/hostapd)
...
-i<ifname> Interface to listen on (default: first interface found in the
socket path)
Below is a run with the default script and with my proposed solution.
Default script (with logging added):
==================================
root@OpenWrt:/# cat /etc/rc.button/wps
#!/bin/sh
if [ "$ACTION" = "pressed" -a "$BUTTON" = "wps" ]; then
for dir in /var/run/hostapd*; do
[ -d "$dir" ] || continue
logger "WPS activated for: $dir"
hostapd_cli -p "$dir" wps_pbc
done
fi
>>>> WPS BUTTON PRESSED <<<<<
root@OpenWrt:/# hostapd_cli -p /var/run/hostapd -i wlan0 wps_get_status
PBC Status: Active
Last WPS result: None
root@OpenWrt:/# hostapd_cli -p /var/run/hostapd -i wlan1 wps_get_status
PBC Status: Timed-out
Last WPS result: None
root@OpenWrt:/# logread | grep WPS
Tue Apr 14 18:38:50 2015 user.notice root: WPS activated for: /var/run/hostapd
wlan0 got WPS activated, while wlan1 remained inactive.
I have modified the script to search for sockets instead of directories and
to use the "-i" option with hostapd_cli, and now the script properly
activates wps for both radios. As "-i" needs the interface name instead of
the full path, the script first changes dir to /var/run/hostapd to get simply
the interface names.
Modified script (with logging):
===============================
root@OpenWrt:/# cat /etc/rc.button/wps
#!/bin/sh
if [ "$ACTION" = "pressed" -a "$BUTTON" = "wps" ]; then
cd /var/run/hostapd
for dir in *; do
[ -S "$socket" ] || continue
logger "WPS activated for: $socket"
hostapd_cli -i "$socket" wps_pbc
done
fi
>>>> WPS BUTTON PRESSED <<<<<
root@OpenWrt:/# hostapd_cli -p /var/run/hostapd -i wlan0 wps_get_status
PBC Status: Active
Last WPS result: None
root@OpenWrt:/# hostapd_cli -p /var/run/hostapd -i wlan1 wps_get_status
PBC Status: Active
Last WPS result: None
root@OpenWrt:/# logread | grep WPS
Tue Apr 14 18:53:06 2015 user.notice root: WPS activated for: wlan0
Tue Apr 14 18:53:06 2015 user.notice root: WPS activated for: wlan1
Both radios got their WPS activated properly.
I am not sure if my solution is optimal, but it seems to work. WPS button is
maybe not that often used functionality, but it might be fixed in any case.
Routers with multiple radios are common now, so the bug is maybe more
prominent than earlier.
The modified script has been in a slightly different format in my community
build since r42420 in September 2014.
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
SVN-Revision: 45492
Two errors "netifd: radio0: sh: bad number" have recently surfaced in system
log in trunk when wifi interfaces come up. I tracked the errors to checking
numerical values of some config options without ensuring that the option has
any value.
The errors I see have apparently been introduced by r45051 (ieee80211r in
hostapd) and r45326 (start_disabled in mac80211). My patches fix two
instances of "bad number", but there may be a third one, as the original
report in bug 19345 pre-dates r45326 and already has two "bad number" errors
for radio0.
https://dev.openwrt.org/ticket/19345
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
SVN-Revision: 45380
r45270 removed ieee80211n=%d from the format string but didn't remove
the parameter itself. Though this probably doesn't cause any harm, it's
quite confusing and unneeded.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 45351
To enable 802.11r, wpa_key_mgmt should contain FT-EAP or FT-PSK. Allow
multiple key management algorithms to make this possible.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
SVN-Revision: 45050
The 802.11r implementation in hostapd uses nas_identifier as PMK-R0 Key
Holder identifier. As 802.11r can also be used with WPA Personal, nasid
should be appended to the hostapd config for all WPA types.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
SVN-Revision: 45049
'hostapd-common' is needed by all of the variants for wifi to function
correctly (a number of the target profiles simply select 'wpad-mini').
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
SVN-Revision: 45048
These new variants include support for mesh mode and SAE crypto.
They always depend on openssl as EC operations are not provided by
the internal crypto implementation.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 45047
