Make sure the timestamp of the root directory of the initramfs is set
to SOURCE_DATE_EPOCH as well.
Fixes: 29d7461d11 ("kernel: set options to make external initramfs reproducible")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Introduce `sha256_unsigned` which is a checksum of the image _before_ a
signature is attached. This is helpful to compare image reproducibility.
Since the `.sha256sum` file is located in the $(KDIR) folder, switch
$(BIN_DIR) with $(KDIR) to simplify the code. The value of $(BIN_DIR)
itself is not stored inside the resulting JSON file, so it can be
replaced.
Signed-off-by: Paul Spooren <mail@aparcar.org>
Make sure xz uses at least 2 threads so compression always runs in
multi-threaded mode as the resulting file in single-threaded mode
differs.
Fixes: 29d7461d11 ("kernel: set options to make external initramfs reproducible")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Drop the -processors argument from the mksquashfs4 call, so it will use
all available processors. This dramatically reduces the time to create
squashfs filesystems.
The times below are observed when building an image for my main router,
the WatchGuard Firebox M300 (qoriq target):
Before:
real 4m45,973s
After:
real 0m23,497s
With this commit `mksquashfs` may use more cores than defined via `-j`.
This is the same behaviour as for archive creation of ImageBuilder, SDK
or toolchain. There is no trivial way to limit `mksquashfs` CPU core
usage to the amount of "free" make jobs since two running `mksquashfs`
instances would each run with the total allowed number (-j) of threads.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
[extended reasoning in commit message]
Signed-off-by: Paul Spooren <mail@aparcar.org>
the cache directory should be autom4te.cache in all $(PKG_AUTOMAKE_PATHS)
rather than $(PKG_BUILD_DIR)/autom4te.cache only
Signed-off-by: Huangbin Zhan <zhanhb88@gmail.com>
Add new module require in 5.15
- Changes in block module
- Changes in netfilter module (log module unified)
- Changes in fs module (mainly new depends for cifs and new ntfs3 module)
- Changes in lib add shared lib now used by more than 1 kmod
- Changes in crypto, dropped one crypto algo added arm crypto accellerator
- Changes in other, add zram default compressor choice and missing lib
by tpm module
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
engine.mk is supposed to be included by engine packages, but it will not
be present in the SDK in the same place as in the main repository.
Move it to include/openssl-engine.mk to avoid this.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
As the upcoming release will be based on Linux 5.10 only, remove all
kernel configuration as well as patches for Linux 5.4.
There were no targets still actively using Linux 5.4.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
HOST_PATCH_DIR is used for host patches, not PATCH_DIR.
Fixes refreshing patches with a custom HOST_PATCH_DIR.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Remove "--mtime" option introduced in commit 18c9faa032 ("tools: zip:
add option for reproducible archives") and instead fetch SOURCE_DATE_EPOCH
environment variable directly in the code.
Ref: https://sourceforge.net/p/infozip/patches/25/
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Zip uses DOS timestamp for mtime which is stored in local time and hence
depends on the timezone of the build system. Force zip to use UTC timezone
to make image builds more reproducible.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
For debugging purposes, we need to know if users are using modified
U-boot versions or not. Currently, the U-boot version is somehow
stripped. This is a little bit problematic when there are
backported/wip/to-upstream patches.
To make it more confusing, there was (before this commit) two U-boot
versioning. U-boot compiled by OpenWrt build bots are missing ``Build:``
This is also the case when the U-boot is compiled locally.
Example:
```
U-Boot SPL 2022.01 (Jan 27 2022 - 00:24:34 +0000)
U-Boot 2022.01 (Jan 27 2022 - 00:24:34 +0000)
```
On the other hand, if you run full build, you can at least see, where it
was compiled. Notice added ``Build:``.
Example:
```
U-Boot 2022.01 (Jan 27 2022 - 00:24:34 +0000), Build: jenkins-turris-os-packages-burstlab-omnia-216
```
In both cases, it is not clear to U-boot developers if it is an unmodified
build. This is also caused that there is a missing ``.git`` file from
U-boot folder, and so there is no history. It leads to that it can not
contain suffix ``-dirty`` (uncommitted modifications) or even something
else like number of commits, etc. [1]
When U-boot is compiled as it should be, the version should look like
this: ``U-Boot 2022.04-rc1-01173-g278195ea1f (Feb 11 2022 - 14:46:50 +0100)``
The date is not changed daily when there are new OpenWrt builds.
This commit adds OpenWrt specific version, which could be verified by
using strings.
```
$ strings bin/targets/mvebu/cortexa9/u-boot-omnia/u-boot-spl.kwb | grep -E "OpenWrt*"
U-Boot SPL 2022.01-OpenWrt-r18942+54-cbfce92367 (Feb 21 2022 - 13:17:34 +0000)
arm-openwrt-linux-muslgnueabi-gcc (OpenWrt GCC 11.2.0 r18942+54-cbfce92367) 11.2.0
2022.01-OpenWrt-r18942+54-cbfce92367
U-Boot 2022.01-OpenWrt-r18942+54-cbfce92367 (Feb 21 2022 - 13:17:34 +0000)
```
[1] https://u-boot.readthedocs.io/en/latest/develop/version.html
Reported-by: Pali Rohár <pali@kernel.org>
Suggested-by: Karel Kočí <karel.koci@nic.cz>
Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
If a image is bigger than the device can handle, an error message is
printed. This is usually silenced and silently ignored, making it harder
to debug. While it's possible to run the build in verbose mode (via
`make V=s`) and grep for *is too big*, it's more intuitive to print the
error message directly. For that use the newly unlocked `$(call
ERROR_MESSAGE,...)` definition which now also print in non-verbose mode.
Fixes: FS#50 (aka #7604)
Signed-off-by: Paul Spooren <mail@aparcar.org>
Using `make -j9` only prints a subset of messages to follow the build
process progressing. However this silently skips over errors which might
be of interested. Using `make V=s` easily floods the terminal making it
hard to find error messages between the lines.
A compromise is the usage of `$(call ERROR_MESSAGE,...)` which prints a
message in red. This function is silenced in the non-verbose mode, even
if only used at a single place in `package/Makefile` where it notifies
about a OPKG corner case.
This commit moves the `ERROR_MESSAGE` definition outside of the
`OPENWRT_VERBOSE` condition and print error messages in every mode.
With this in place further error messages are possible.
Signed-off-by: Paul Spooren <mail@aparcar.org>
Toplevel Make is not aware about changes in the `scripts/config/*conf`
targets and this is causing issues for during update to that part of
build tree, where one needs to handle this manually by either force
rebuilding the targets or running `make config-clean`. Fix this by
forcing the rebuild if necessary.
Fixes: #9297
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Had to update generic defconfig (make kernel_menuconfig CONFIG_TARGET=generic)
for this bump, but since that only modifies the target defined in .config,
and since that target also needed to be updated for unrelated reasons, manually
propagated the newly added symbol to the generic config.
Removed upstreamed:
pending-5.10/860-Revert-ASoC-mediatek-Check-for-error-clk-pointer.patch[1]
All other patches automatically rebased.
1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.10.99&id=080f371d984e8039c66db87f3c54804b0d172329
Build system: x86_64
Build-tested: bcm2711/RPi4B, mt7622/RT3200
Run-tested: bcm2711/RPi4B, mt7622/RT3200
Signed-off-by: John Audia <graysky@archlinux.us>
ipTIME AX2004M is an 802.11ax (Wi-Fi 6) router, based on MediaTek
MT7621A.
Specifications:
* SoC: MT7621A
* RAM: 256 MiB
* Flash: NAND 128 MiB
* Wi-Fi:
* MT7915D: 2.4/5 GHz (DBDC)
* Ethernet: 5x 1GbE
* Switch: SoC built-in
* USB: 1x 3.0
* UART: J4 (115200 baud)
* Pinout: [3V3] (TXD) (RXD) (GND)
MAC addresses:
| interface | MAC address | source | comment
|-----------|-------------------|----------------|---------
| LAN | 58:xx:xx:00:xx:9B | | [1]
| WAN | 58:xx:xx:00:xx:99 | |
| WLAN 2G | 58:xx:xx:00:xx:98 | factory 0x4 |
| WLAN 5G | 5A:xx:xx:40:xx:98 | |
| | 58:xx:xx:00:xx:98 | config ethaddr |
[1] Used in this patch as WLAN 5G MAC address with the local bit set
Load addresses:
* stock
* 0x80010000: FIT image
* 0x81001000: kernel image -> entry
* OpenWrt
* 0x80010000: FIT image
* 0x82000000: uncompressed kernel+relocate image
* 0x80001000: relocated kernel image -> entry
Notes:
* This device has a dual-boot partition scheme, but this firmware works
only on boot partition 1. The stock web interface will flash only on the
inactive boot partition, but the recovery web page will always flash on
boot partition 1.
Installation via recovery mode:
1. Press reset button, power up the device, wait >10s for CPU LED
to stop blinking.
2. Upload recovery image through the recovery web page at 192.168.0.1.
Revert to stock firmware:
1. Install stock image via recovery mode.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
When using a non default MESON_HOST_BUILD_DIR, HOST_BUILD_DIR is not
appropriate to use. This change matches the target configure section.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Commit f4a79148f8 ("ramips: add support for ipTIME AX2004M") seems to
leak KERNEL_LOADADDR 0x82000000 to other devices, causing the to no
longer boot. The leak is visible in u-boot:
Using 'config-1' configuration
Trying 'kernel-1' kernel subimage
Description: MIPS OpenWrt Linux-5.10.92
Type: Kernel Image
Compression: lzma compressed
Data Start: 0x840000e4
Data Size: 10750165 Bytes = 10.3 MiB
Architecture: MIPS
OS: Linux
Load Address: 0x82000000
Entry Point: 0x82000000
Normally, it should look like this:
Using 'config-1' configuration
Trying 'kernel-1' kernel subimage
Description: MIPS OpenWrt Linux-5.10.92
Type: Kernel Image
Compression: lzma compressed
Data Start: 0xbfca00e4
Data Size: 2652547 Bytes = 2.5 MiB
Architecture: MIPS
OS: Linux
Load Address: 0x80001000
Entry Point: 0x80001000
Revert the commit to avoid more people soft-bricking their devices.
This reverts commit f4a79148f8.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
ipTIME NAS1 is a 1-bay NAS, based on Marvell Kirkwood SoC.
Specifications:
* SoC: 88F6281
* RAM: 256 MiB
* Flash: SPI NOR 16 MiB
* SATA: 1x 3Gb/s
* Ethernet: 1x 1GbE
* USB: 1x 2.0
* Fan: 2 speed level
* UART: JP1 (115200 8N1)
* Pinout: [3V3] (TXD) (RXD) (GND)
Notes:
* There are several variants of the model name: "NAS-I", "NASI", "NAS1".
Here "NAS1" is adopted for consistent naming scheme.
* The reset button is also a USB copy button in stock FW,
but in this patch the former is the only default behavior.
Installation via web interface:
1. Flash sysupgrade image through the stock web interface.
Revert to stock firmware:
1. Perform sysupgrade with stock image.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
This allows to implement statefull bridge filtering
As the uncompressed size is only 7.6k (arm64), just add
nf_conntrack_bridge.ko to kmod-nft-bridge package
Signed-off-by: Etienne Champetier <champetier.etienne@gmail.com>
On macOS, system binaries silently drop the environment variables for injecting
extra shared libraries (used by fakeroot). This is done for security reasons.
Work around this by building bash from source, so that it gets an ad-hoc signature
and does not have these restrictions
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Ubuntu started to flag which as deprecated and it
seems which is not really standard and may vary
across Distro.
Drop the use of which and use the standard 'command -v'
for this simple task.
Which is still present in the prereq if some package/script
still use which.
A utility script called command_all.sh is implemented that
will just mimic the output of which -a.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Added HOST_CXXFLAGS to specify CXXFLAGS during host-compile
(e.g. to specify c++ standard: HOST_CXXFLAGS += -std=c++11)
Signed-off-by: Sergey V. Lobanov <sergey@lobanov.in>
Move the kernel versions and hash to dedicated files.
This makes kernel bump quicker and fix some annoying
problem with rebasing when multiple kernel bump are proposed.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
[Rebased on top of current master]
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Add and enable a new kconfig knob to disable unprivileged eBPF by default.
Patches automatically rebased.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
All patches automatically rebased.
Build system: x86_64
Build-tested: ramips/mt7621*
*Had to revert 7f1edbd in order to build due to FS#4149
Signed-off-by: John Audia <graysky@archlinux.us>
This CPU type is compatible with NXP's PPC based QorIQ processors, and
will be used by the upcoming new qoriq target.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Reviewed-by: Rui Salvaterra <rsalvaterra@gmail.com>
All patches automatically rebased.
Build system: x86_64
Build-tested: bcm2711/RPi4B, ipq806x/R7800*
Run-tested: bcm2711/RPi4B, ipq806x/R7800*
*Had to revert 7f1edbd412 in order to build
(binutils 2.37, https://bugs.openwrt.org/index.php?do=details&task_id=4149)
Signed-off-by: John Audia <graysky@archlinux.us>
All patches automatically rebased.
Build system: x86_64
Build-tested: bcm2711/RPi4B, ipq806x/R7800*
Run-tested: bcm2711/RPi4B, ipq806x/R7800*
*Had to revert 7f1edbd412 in order to build
(binutils 2.37, https://bugs.openwrt.org/index.php?do=details&task_id=4149)
Signed-off-by: John Audia <graysky@archlinux.us>
Removed target for patch which does not exist:
bcm27xx/patches-5.10/950-0249-kbuild-Disable-gcc-plugins.patch
All patches automatically rebased.
Build system: x86_64
Build-tested: bcm2711/RPi4B, ipq806x/R7800*
Run-tested: bcm2711/RPi4B, ipq806x/R7800*
* Had to revert 7f1edbd412 in order to build
(binutils 2.37, https://bugs.openwrt.org/index.php?do=details&task_id=4149)
Signed-off-by: John Audia <graysky@archlinux.us>
All patches automatically rebased.
Build system: x86_64
Build-tested: ramips/mt7621*
*FS#4149 affects me so I had to revert 7f1edbd412
in order to downgrade to 2.35.1
Signed-off-by: John Audia <graysky@archlinux.us>
All patches automatically rebased.
Build system: x86_64
Build-tested: ramips/mt7621*
*FS#4149 affects me so I had to revert 7f1edbd412
in order to downgrade to 2.35.1
Signed-off-by: John Audia <graysky@archlinux.us>
All patches automatically rebased.
Build system: x86_64
Build-tested: ramips/mt7621*
*FS#4149 affects me so I had to revert 7f1edbd412
in order to downgrade to 2.35.1
Signed-off-by: John Audia <graysky@archlinux.us>
Added support to generate dynamic-sized VHDX images for Hyper-V.
Compile-tested on x86 and run-tested on Windows 10 21H2 (Hyper-V).
Signed-off-by: Oldřich Jedlička <oldium.pro@gmail.com>
change meson binary to use py extension. Fixes issue with meson's
symbolextractor using the host python instead of the system one.
We intentionally use a .py extension here so that meson launches
additional python scripts with the same build host python interpreter as
itself is running under (and not the host package one once it becomes
available)
Signed-off-by: Rosen Penev <rosenp@gmail.com>
CONFIG_EXTERNAL_CPIO is a string variable, hence testing for 'y'
doesn't make much sense here.
Fixes: 330bd380e8 ("image: allow building FIT and uImage with ramdisk")
Reported-by: Huangbin Zhan <zhanhb88@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Newer NAND devices from MikroTik like the hAP ac3
require the kernel to be packed into UBIFS and then
ubinized.
So, since the ubinize-image.sh script can now ubinize
kernel only as well lets add a command for it.
This now allows calling ubinize-kernel in the kernel
packaging at then end.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Rootfs is now optional in ubinize-image.sh and
requires --rootfs flag instead of just passing the
rootfs image as the argument before ubinize opts.
So, simply add --rootfs flag before the $(IMAGE_ROOTFS).
Signed-off-by: Robert Marko <robimarko@gmail.com>
All patches automatically rebased.
Build system: x86_64
Build-tested: ramips/mt7621*
*I am hit with the binutils 2.37 bug so I had to revert 7f1edbd412
in order to downgrade to 2.35.1
Signed-off-by: John Audia <graysky@archlinux.us>
Manually rebased:
generic-backport/850-v5.13-usb-ehci-add-spurious-flag-to-disable-overcurrent-ch.patch
All other patches automatically rebased.
Signed-off-by: John Audia <graysky@archlinux.us>
BTF pointer data has a different size on 32 vs 64 bit targets,
and while the generated eBPF code works, the BTF data fails to validate
on mismatch
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This allows a package to be rebuilt for all different VARIANTs.
To do so, set VARIANT=*.
The wpa-cli package is not getting built after changes made by
19aae94 [build: avoid rebuilds of unset VARIANT packages], because
wpa-cli is only built when compiling a variant that includes
supplicant support, and the first selected variant may not build it.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
Removed upstreamed:
backport-5.4/790-v5.7-net-switchdev-do-not-propagate-bridge-updates-across.patch
All other patches automatically rebased.
Signed-off-by: John Audia <graysky@archlinux.us>
When the prebuilt llvm toolchain is unpacked into the source dir,
it is automatically picked up and used by the build system, and eBPF
based packages can be selected
Signed-off-by: Felix Fietkau <nbd@nbd.name>
