The patch 0022-dts-ipq4019-support-ARMv7-PMU.patch
was merged into 4.8-rc1.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[refresh patches]
Signed-off-by: Mathias Kresin <dev@kresin.me>
During the integration of the ipq40xx target,
the phy drivers were included into the ipq806x's
target kernel config.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch renames the AVM FRITZ!Box 4040's board-2.bin
file and package to match the 'vendor_product' format.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch aligns the device-tree file with the latest
guidelines.
- No longer include qcom-ipq4019-ap.dk01.1.dtsi. This
file is only partially upstream and therefore subjected
to changes that might not be compatible with the board.
As a result, the definitions from the file have been
copied into this dts.
- exclusively use decimal GPIO addresses.
- reorganize the reserved-memory layout to waste less
memory. There's no point in keeping the u-boot loader
around. This should also make it possible to create
an image that will boot with the original EVA/ADAM2 loader
without needing to install the modified u-boot loader.
And finally mark the "tz-apps" as reusable.
There isn't a way to upload apps to the trust-zone in OpenWrt
yet. But it might see some use in the future as a "secure"
key-store/TPM.
- sort the first-level nodes alphabetically.
- sort nodes with an address by the address.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
According to console log during TP-Link TL-WR840N v5 OEM firmware update
procedure 0x3e0000-0x3f0000 64kB "config" partition, which is used to store
router's configuration settings, is erased and recreated again during every
OEM firmware update procedure, thus does not contain any valuable factory data.
So it is conviniant to use this extra 64kB erase block for jffs overlay due
limited flash size on this device like it used on TP-Link's ar71xx boards.
Signed-off-by: Serg Studzinskii <serguzhg@gmail.com>
The platform_check_image() stub need to return 0 for success, otherwise
the sysupgrade will fail with:
Image check 'platform_check_image' failed.
Fixes: aa6f5f1787 ("kirkwood: use image metadata")
Signed-off-by: 尤晓杰 <yxj790222@163.com>
[reworded commit message}
Signed-off-by: Mathias Kresin <dev@kresin.me>
Use the first found directory in the tar archive instead of relying on
a directory named according to the userspace boardname.
It allows to change the boardname without adding another compatibility
layer to the zyxel sysupgrade.
Fixes: 33f09cf151 ("ipq806x: convert to dt-based board-detection")
Signed-off-by: Mathias Kresin <dev@kresin.me>
The setup code of the OpenMesh OM5P ACv2 device uses nothing
from the mdio-gpio.h header, so remove the inclusion of that.
Also remove the kernel version check which is needed only
because the mdio-gpio.h header exists in a different path
in older kernels.
Compile tested only.
Cc: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
Commit e15c63a375 ("ar71xx: add support for MikroTik RouterBOARD wAP
G-5HacT2HnD (wAP AC") broke the format of the patches. In unified diff
format, the unchanged, contextual lines must be preceded by a space
character.
Refresh the patches with quilt to fix them.
Fixes: e15c63a375 ("ar71xx: add support for MikroTik RouterBOARD wAPG-5HacT2HnD (wAP AC")
Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
The patches introduced in commit 20e68f6d39 ("ar71xx: kernel: enable
PCI on QCA9556 SoC") have non standard format. In unified diff format,
the unchanged, contextual lines must be preceded by a space character.
Refresh the patches with quilt to fix them.
Fixes: 20e68f6d39 ("ar71xx: kernel: enable PCI on QCA9556 SoC")
Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
The setup code defines four individual structures for the
Reset buttons of the supported boards. The only difference
between the definitions is the GPIO number used for the
button.
Replace the different structures with one generic variant,
and add a helper function to simplify the button registration.
Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
The Gateworks GW5520 board uses 2x intel gigabit mac's, instead of the
internal i.MX6 FEC.
Add support for these.
Signed-off-by: Scott V. Kamp <outbackdingo@gmail.com>
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Picking commit from QSDK
https://source.codeaurora.org/quic/qsdk/oss/kernel/linux-msm/commit/?h=eggplant&id=a86bda9f8a7965f0cedd347a9c04800eb9f41ea3
Commit message:
"During removal of the glue layer(dwc3-of-simple), USB master reset is set to active and during insertion it is de-activated."
Change-Id: I537dc810f6cb2a46664ee674840145066432b957
Signed-off-by: Vasudevan Murugesan <vmuruges@codeaurora.org>
(cherry picked from commit 4611e13580a216812f85f0801b95442d02eeb836)"
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
A newer clk and cpufreq drivers for ipq806x platform had been sent upstream.
A change that i have noticed is that now it's possible to set min, cur and max frequencies from sysfs (previously it was bugged and caused nothing).
Following patches are removed:
- 0036-clk-Avoid-sending-high-rates-to-downstream-clocks-du.patch - seems it was dropped from the patchset by current committer.
- 0044-clk-qcom-krait-Remove-CLK_IS_ROOT.patch - already applied to the driver itself in the corresponding patch.
- 0057-clk-qcom-Add-regmap-mux-div-clocks-support.patch - seem to be irrelevant to ipq806x.
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
According to QSDK and OEM tarballs (checked c2600, r7500v2, r7800) 2nd pci slot (pci1, 2,4 GHz card)) on ap148 based boards should operate in gen1 mode.
EA8500 is an exception and according to GPL pcie0 should operate in gen1 mode.
In previous commit we've added the support for this option, so enable it in DT for affected devices.
QSDK ref:
https://source.codeaurora.org/quic/qsdk/oss/kernel/linux-msm/commit/?h=release/endive_preview_cc&id=f3b07fe309027c52fc163149500cedddd707c506
While at it move the phy transmit termination offset value into dtsi file as it's platform specific.
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
In current state there's huge regression on ipq806x target that causes the device to transmit broken/malformed frames that are not corrected/detected by error control mechanisms and other less severe issues.
https://bugs.lede-project.org/index.php?do=details&task_id=1197
This finally had been narrowed down to patch 0071-pcie-qcom-fixes.patch
Meanwhile QSDK contains a handful of commits that add support for ipq806x to upstream qcom pcie driver
https://source.codeaurora.org/quic/qsdk/oss/kernel/linux-msm/log/drivers/pci/host/pcie-qcom.c?h=eggplant
Unfortunately qca developers do not bother to push it upstream.
Using those commits instead of lede 0071 patch fixes mentioned issue and probably many others as it seems that corrupted data has been originating within pcie misconfiguration.
Fixes: FS#1197 and probably others
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
The blue LED is what other firmwares use for this device, and it's a lot
easier on the eyes than its shade of yellow, which implies an error
condition.
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
[merge into existing $boardname:blue:status block]
Signed-off-by: Mathias Kresin <dev@kresin.me>
Acked-by: Piotr Dymacz <pepe2k@gmail.com>
Acked-by: Cezary Jackiewicz <cezary@eko.one.pl>
TP-Link Archer C20 v4 is a router with 5-port FE switch and
non-detachable antennas. It's based on MediaTek MT7628N+MT7610EN.
Specification:
- MediaTek MT7628N/N (580 Mhz)
- 64 MB of RAM
- 8 MB of FLASH
- 2T2R 2.4 GHz and 1T1R 5 GHz
- 5x 10/100 Mbps Ethernet
- 3x external, non-detachable antennas
- UART (J1) header on PCB (115200 8n1)
- 7x LED (GPIO-controlled*), 2x button, power input switch
* WAN LED in this devices is a dual-color, dual-leads type which isn't
(fully) supported by gpio-leds driver. This type of LED requires both
GPIOs state change at the same time to select color or turn it off.
For now, we support/use only the green part of the LED.
* MT7610EN ac chip isn't not supported by LEDE. Therefore 5Ghz won't
work.
Flash instruction:
The only way to flash LEDE image in ArcherC20v4 is to use
tftp recovery mode in U-Boot:
1. Configure PC with static IP 192.168.0.66/24 and tftp server.
2. Rename "openwrt-ramips-mt7628-ArcherC20v4-squashfs-tftp-recovery.bin"
to "tp_recovery.bin" and place it in tftp server directory.
3. Connect PC with one of LAN ports, press the reset button, power up
the router and keep button pressed for around 6-7 seconds, until
device starts downloading the file.
4. Router will download file from server, write it to flash and reboot.
Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
This changes device name from "TP-Link Archer C20" to "TP-Link Archer C20 v1"
because of TPLINK released new TP-Link Archer C20 v4. Additionally
migration to the generic board detection has been made.
Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
Match mapping of the switch LEDs according to the TP-Link
firmware behavior. LAN port 1 triggers the most right LAN LED,
LAN port 2 the second LAN LED from the right and so on.
Signed-off-by: David Bauer <mail@david-bauer.net>
As long as we can't enforce image metadata, we need to use (platform)
image checks to have at least soem kind of validation.
Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
Ubifs is disabled for all boards except the evaluation boards and the
Fritz!Box 4040 anyway. According the author, the ubifs support for the
Fritz!Box 4040 wasn't enabled on purpose.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Remove leftover code used for legacy images. There are no relevant
binary differences for the images after removing the legacy leftovers.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Initialise the filesystem specific build command. Otherwise it will be
unintended inherit to following images and will cause a wrong image
format.
The issue is around for ages but was only recently triggered due to the
added support for the Openmesh a42.
Fixes: FS#1276
Signed-off-by: Mathias Kresin <dev@kresin.me>
Current EnGenius ENS202EXT factory image recipe version causes factory
images of the following devices to be corrupted. This issue wasn't
visible until recent changes of image Makefile snippets order.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Remove leftover reference to a not existing kmod-usb-musb-tusb6010 from
the omap24xx target, the corresponding module is built into the kernel.
Fixes: 96815fe0a2 ("kernel: remove omap24xx specific kernel module packages")
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
This patch adds support for the MikroTik RouterBOARD wAP G-5HacT2HnD (wAP
AC), a small weatherproof dual band, dual-radio 802.11ac wireless AP with
integrated omnidirectional anntennae and one 10/100/1000 Mbps Ethernet
ports.
See https://mikrotik.com/product/RBwAPG-5HacT2HnD for more info.
Specifications:
- SoC: Qualcomm Atheros QCA9556
- RAM: 64 MB
- Storage: 16 MB NOR
- Wireless:
· Atheros AR9550 (SoC) 802.11b/g/n 2x2:2, 2 dBi antennae
· Qualcomm QCA9880 802.11a/n/ac 3x3:3, 2 dBi antennae
- Ethernet: Atheros AG71xx (SoC, AR8033), 1x 1000/100/10 port, passive
PoE in
Working:
- Board/system detection
- Sysupgrade
- Serial console
- Ethernet
- 2.4 GHz radio
- 5 GHz radio
- Reset button
Not working:
- LEDs (added according to Mikrotik's GPL sources but not functional)
Unsupported:
- ZT2046Q SPI temperature and voltage sensor
Contributors: Giuseppe Tipaldi (@Ciusss89)
Ricky (@rickydee)
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
[daniel@makrotopia.org: whitespace fix, use PHYADDR instead of PHYMASK]
This patch enables the PCI bus on the QCA9556 SoC, the same way it is
done on the same family SoC QCA9558.
Tested on a MikroTik RouterBoard wAPG-5HacT2HnD (wAP AC).
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
ALFA Network AC1200RM is an AC1200 router, with 5-port FE switch and
USB 2.0 port. Device is based on MediaTek MT7620A + MT7612EN.
Specification:
- MT7620A (580 MHz)
- 64 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 5x 10/100 Mbps Ethernet with passive PoE output in WAN and LAN4
- 2T2R 2.4 GHz (MT7620A)
- 2T2R 5 GHz (MT7612EN)
- 1x USB 2.0
- 9x LED (8 driven by GPIO)
- 1x button (reset)
- DC jack for main power input (12-24 V)
- 2x UART, I2C, I2S and LED headers
Flash instruction (do it under U-Boot, using UART and TFTP server):
Select option "2: Load system code then write to Flash via TFTP" and
use "sysupgrade" image.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
GL.iNet GL-AR750 is a small size, dual-band (AC750) router, based on
Qualcomm/Atheros QCA9531 v2 + QCA9887. FCC ID: 2AFIW-AR750.
Specification:
- 650/597/216 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 3x 10/100 Mbps Ethernet
- 2T2R 2.4 GHz (QCA9531)
- 1T1R 5 GHz (QCA9887)
- 1x USB 2.0 (power controlled by GPIO)
- 1x microSD (GL857L)
- 3x LED (all driven by GPIO)
- 1x button (reset)
- 1x 2-pos switch
- header for optional PoE module
- 1x micro USB for main power input
- UART + I2C header on PCB
Flash instruction:
Vendor firmware is based on OpenWrt/LEDE. GUI or sysupgrade can be used
to flash OpenWrt/LEDE firmware.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
