The beeper is currently not fully functional and has also
been removed from DTS.
Also remove the dependency for the gpio-beeper module.
Fixes: 695a1cd53c ("ath79: add support for MikroTik RouterBOARD 912UAG-2HPnD")
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
This board has been supported in the ar71xx.
Links:
* https://mikrotik.com/product/RB912UAG-2HPnD
* https://openwrt.org/toh/hwdata/mikrotik/mikrotik_rb912uag-2hpnd
This also supports the 5GHz flavour of the board.
Hardware:
* SoC: Atheros AR9342,
* RAM: DDR 64MB,
* SPI NOR: 64KB,
* NAND: 128MB,
* Ethernet: x1 10/100/1000 port with passive POE in,
* Wi-Fi: 802.11 b/g/n,
* PCIe,
* USB: 2.0 EHCI controller, connected to mPCIe slot and a Type-A
port -- both can be used for LTE modem, but only one can be
used at any time.
* LEDs: 5 general purpose LEDs (led1..led5), power LED, user LED,
Ethernet phy LED,
* Button,
* Beeper.
Not working:
* Button: it shares gpio line 15 with NAND ALE and NAND IO7,
and current drivers doesn't easily support this configuration,
* Beeper: it is connected to bit 5 of a serial shift register
(tested with sysfs led trigger timer). But kmod-gpio-beeper
doesn't work -- we left this as is for now.
Flashing:
* Use the RouterBOARD Reset button to enable TFTP netboot,
boot kernel and initramfs and then perform sysupgrade.
* From ar71xx OpenWrt firmware run:
$ sysupgrade -F /tmp/<sysupgrade.bin>
For more info see: https://openwrt.org/toh/mikrotik/common.
Co-Developed-by: Koen Vandeputte <koen.vandeputte@citymesh.com>
Reviewed-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Signed-off-by: Denis Kalashnikov <denis281089@gmail.com>
This patch enables the SFP cage on the MikroTik RouterBOARD 922UAGS-5HPacD.
GPIO16 (tx-disable-gpios) should be governed by the SFP driver to enable
or disable transmission, but no change is observed. Therefore, it is
left as output high to ensure the SFP module is forced to transmit.
Tested on a RouterBOARD 922UAGS-5HPacD board, with a CISCO GLC-LH-SMD
1310nm module and an unbranded GLC-T RJ45 Gigabit module. PC=>router
iperf3 tests deliver 440/300 Mbps up/down, both via regular eth0 port
or SFP port with RJ45 module. Bridge between eth0 and eth1 delivers
950 Mbps symmetric.
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
This patch adds support for the MikroTik RouterBOARD wAPR-2nD (wAP R)
router, a weatherproof 2.4 GHz access point with a miniPCI-e slot and
a SIM card slot.
Specifications:
- SoC: Qualcomm Atheros QCA9533
- Flash: 16 MB (SPI)
- RAM: 64 MB
- Ethernet: 1x 10/100 Mbps (PoE in)
- WiFi: AR9531 2T2R 2.4 GHz (SoC)
- miniPCI-e slot
- 4x green LEDs (1x WiFi, 3x RSSI)
- 1x reset button
See https://mikrotik.com/product/RBwAPR-2nD for more details.
Flashing:
TFTP boot initramfs image and then perform sysupgrade. Follow common
MikroTik procedure as in https://openwrt.org/toh/mikrotik/common.
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
The MikroTik SXT Lite5 (product code RBSXT5nDr2, also SXT 5nD r2) is
an outdoor 5GHz CPE with a 16 dBi integrated antenna built around the
Atheros AR9344 SoC. It is based on the "sxt5n" board platform.
Specifications:
- SoC: Atheros AR9344
- RAM: 64 MB
- Storage: 128 MB NAND
- Wireless: Atheros AR9340 (SoC) 802.11a/n 2x2:2
- Ethernet: Atheros AR8229 switch (SoC), 1x 10/100 port,
8-32 Vdc PoE in
- 6 user-controllable LEDs:
· 1x power (blue)
· 1x wlan (green)
· 4x rssi (green)
- 1 GPIO-controlled buzzer
See https://mikrotik.com/product/RBSXT5nDr2 for more details.
Notes:
The device was already supported in the ar71xx target. There, the
Ethernet port was handled by GMAC1. Here in ath79 it is handled by
GMAC0, which allows to get link information (loss, speed, duplex) on
the eth0 interface.
Flashing:
TFTP boot initramfs image and then perform sysupgrade. Follow common
MikroTik procedure as in https://openwrt.org/toh/mikrotik/common.
Acknowledgments:
Michael Pratt (@mpratt14) for helping on the network settings.
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
[rebase, use mikrotik LED label prefix, make names consistent,
add reg for bootloader2, use led_user for boot indication etc.,
minor cosmetic changes]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The MikroTik RouterBOARD 921GS-5HPacD-15s (mANTBox 15s) is an outdoor
antenna for 5 GHz with an built-in router. This ports the board from
ar71xx.
See https://mikrotik.com/product/RB921GS-5HPacD-15S for more info.
Specifications:
- SoC: Qualcomm Atheros QCA9558 (720 MHz)
- RAM: 128 MB
- Storage: 128 MB NAND
- Wireless: external QCA9892 802.11a/ac 2x2:2
- Ethernet: 1x 1000/100/10 Mbps, integrated, via AR8031 PHY, passive PoE in
- SFP: 1x host
Working:
- NAND storage detection
- Ethernet
- Wireless
- 1x user LED (blinks during boot, sysupgrade)
- Reset button
- Sysupgrade
Untested:
- SFP cage (probably not working)
Installation (untested):
- Boot initramfs image via TFTP and then flash sysupgrade image
As the embedded RB921-pcb is a stripped down version of the RB922 this patch
adds a common dtsi for this series and includes this to the final dts-files.
Signed-off-by: Sven Roederer <devel-sven@geroedel.de>
[move ath10k-leds closer to ath10k definition in DTS files]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The MikroTik RouterBOARD LHG 2nD (sold as LHG 2) is a 2.4 GHz
802.11b/g/n outdoor device with a feed and an integrated dual
polarization grid dish antenna based on the LHG-HB platform.
See https://mikrotik.com/product/lhg_2 for more info.
Specifications:
- SoC: Qualcomm Atheros QCA9533
- RAM: 64 MB
- Storage: 16 MB NOR
- Wireless: Atheros AR9531 (SoC) 802.11b/g/n 2x2:2, 18 dBi antenna
- Ethernet: Atheros AR8229 (SoC), 1x 10/100 port, 12-28 Vdc PoE in
- 8 user-controllable LEDs:
· 1x power (blue)
· 1x user (green)
· 1x lan (green)
· 1x wlan (green)
· 4x rssi (green)
Note:
The rssihigh LED is disabled, as it shares GPIO 16 with the reset
button.
Flashing:
TFTP boot initramfs image and then perform sysupgrade. Follow common
MikroTik procedure as in https://openwrt.org/toh/mikrotik/common.
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
[rebase, remove rssiled setup, adjust commit message, add DTSIs]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Move the image preparation and nand-utils package selection into
common device definitions for NOR/NAND devices.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This patch adds support for the MikroTik RouterBOARD RB493G, ported
from the ar71xx target.
See https://routerboard.com/RB493G for details
Specification:
- SoC Qualcomm Atheros AR7161
- RAM: 256 MiB
- Storage: 128MiB NAND
- Ethernet: 9x 1000/100/10 Mbps
- USB 1x 2.0 / 1.0 type A
- PCIe: 3x Mini slot
- MicroSD slot
Working:
- Board/system detection
- Ethernet
- SPI
- NAND
- LEDs
- USB
- Sysupgrade
Enabled (but untested due to lack of hardware):
- PCIe - ath79_pci_irq struct has the slot/pin/IRQ mappings if needed
Installation methods:
- tftp boot initramfs image, scp then flash via "sysupgrade -n"
- nand boot existing OpenWrt, scp then flash via "sysupgrade -n"
Notes:
- initramfs image will not work if uncompressed image size over ~8.5Mb
- The "rb4xx" drivers have been enabled
Signed-off-by: Christopher Hill <ch6574@gmail.com>
Now that check-size uses IMAGE_SIZE by default, we can skip the argument from
image recipes to reduce redundancy.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
[do not touch ar71xx]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
So far, specifying "BOARD_NAME := routerboard" is required by the
upgrade code of Mikrotik NAND devices, as "sysupgrade-routerboard"
is hardcoded in platform_do_upgrade_mikrotik_nand().
This patch replaces the latter with a grep for the name like it
is already done in nand_upgrade_tar() in /lib/upgrade/nand.sh.
By that, BOARD_NAME is obsolete now for this device.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This commit creates the ath79/mikrotik subtarget in order to support
MikroTik devices based on Qualcomm Atheros MIPS SoCs.
MikroTik devices need a couple of specific features: the split MiNOR
firmware MTD format, which is not used by other devices, and the 4k
sector erase size on SPI NOR storage, which can not be added to the
ath79/generic and ath79/nand subtargets now.
Additionally, the commit moves the two MikroTik devices already in
the generic and nand subtargets to this new one.
Tested on the RB922 board and the wAP AC router.
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
