Pass the correct device name in the network_del ubus call
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit 80ba0d958dc96fb7aba26614f71325507fabd58a)
The USB PHY on the ar9330 and similar SoCs needs the PHY driver. In
OpenWrt 23.05 it was compiled into the kernel. The kernel 6.6
configuration does not compile it in any more, make the
kmod-usb-chipidea driver select it to add it to the images.
Fixes: https://github.com/openwrt/openwrt/issues/17710
Fixes: 04bdf9b3323e ("ath79: disable ath79 USB phy drivers by default")
Link: https://github.com/openwrt/openwrt/pull/17720
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit b467e5a0afebbc4982213c03f90dfc6deb717b36)
atm_qos struct should be the same both for user and kernel spaces. Via
the __SO_ENCODE() macro it is used to define the SO_ATMQOS socket IOC.
During the VRX518 support introduction, the atm_trafprm sturct nested
into the atm_qos stucture was update with newer fields that are
referenced by the ATM TC layer of the VRX518 TC driver. These new fields
are intended to communicate information for extra traffic classes
supported by the driver. But we are still using vanilla kernel headers
to build the toolchain. Due to the atm.h header incoherency br2684ctl
from linux-atm tools is incapable to configure the ATM bridge netdev:
br2684ctl: Interface "dsl0" created sucessfully
br2684ctl: Communicating over ATM 0.1.2, encapsulation: LLC
br2684ctl: setsockopt SO_ATMQOS 22 <-- EINVAL errno
br2684ctl: Fatal: failed to connect on socket; File descriptor in bad state
There are two options to fix this incoherency. (a) update the header
file in the toolchain to build linux-atm against updated atm_trafprm and
atm_qos structures, or (b) revert atm_trafprm changes.
Since there are no actual users of the extra ATM QoS traffic classes,
just drop these extra traffic classes from vrx518_tc ATM TC layer and
drop the kernel patch updating atm.h.
Besides fixing the compatibility with linux-atm tools, removing the
kernel patch should simplify kernel updates removing unneeded burden of
maintenance.
Run tested with FRITZ!Box 7530 with disabled extra traffic classes and
then removed them entirely before the submission.
CC: John Crispin <john@phrozen.org>
Fixes: cfd42a0098 ("ipq40xx: add Intel/Lantiq ATM hacks")
Suggested-by: Andre Heider <a.heider@gmail.com>
Reported-and-tested-by: nebibigon93@yandex.ru
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Link: https://patchwork.ozlabs.org/project/openwrt/patch/20250122222654.21833-4-ryazanov.s.a@gmail.com/
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 6d6dc3a3c967174598a44503f4af281574660356)
ATM TC layer have some issues which effectively prevent VRX518 from
being used as ADSL modem. Specifically, there one crash during the ATM
layer configuration and wrong PVC ID selection on packet receiving what
breaks RX path. Fix both of the issues. Make subif iface registration
optional to prevent the crash (see more details in the new patch) and
update the hardcoded PVC ID to match the first allocated channel.
Run tested with FRITZ!Box 7530.
Fixes: 474bbe23b7 ("kernel: add Intel/Lantiq VRX518 TC driver")
Reported-and-tested-by: nebibigon93@yandex.ru
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Link: https://patchwork.ozlabs.org/project/openwrt/patch/20250122222654.21833-3-ryazanov.s.a@gmail.com/
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 470335450e67002366fcbcd7334b15bdf008e44d)
It looks like VRX518 returns phys addr of data buffer in the 'data_ptr'
field of the RX descriptor and an actual data offset within the buffer
in the 'byte_off' field. In order to map the phys address back to
virtual we need the original phys address of the allocated buffer.
In the same driver applies offset to phys address before the mapping,
what leads to WARN_ON triggering in plat_mem_virt() function with
subsequent kernel panic:
WARNING: CPU: 0 PID: 0 at .../sw_plat.c:764 0xbf306cd0 [vrx518_tc@8af9f5d0+0x25000]
...
Unable to handle kernel NULL pointer dereference at virtual address 00000000
pgd = aff5701e
[00000000] *pgd=00000000
Internal error: Oops: 5 [#1] SMP ARM
Noticed in ATM mode, when chip always returns byte_off = 4.
In order to fix the issue, pass the phys address to plat_mem_virt() as
is and apply byte_off later for proper DMA syncing and on mapped virtual
address when copying RXed data into the skb.
Run tested with FRITZ!Box 7530 on both ADSL and VDSL (thanks Jan) links.
Fixes: 474bbe23b7 ("kernel: add Intel/Lantiq VRX518 TC driver")
Tested-by: Jan Hoffmann <jan@3e8.eu> # VDSL link
Reported-and-tested-by: nebibigon93@yandex.ru # ADSL link
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Link: https://patchwork.ozlabs.org/project/openwrt/patch/20250122222654.21833-2-ryazanov.s.a@gmail.com/
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 7bd579689d2304c73c263be3e030d76c551d6e87)
The lldp_class and lldp_location config option are only valid when
compiled with LLDP-MED support. If not they will cause lldpd not to
start.
Signed-off-by: Sebastian Pflieger <sebastian@pflieger.email>
Link: https://github.com/openwrt/openwrt/pull/17571
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 2c22d7c3a4a7edcce1af656c8cddb1ab163e3d02)
lldpd was updated, so reset PKG_RELEASE after the PKG_VERSION update.
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit abbec429b40f149f9c5a99a64ee7bf4e804fbb7d)
Changes (breaking):
- Remove support for building 802.3bt TLVs (broken).
Fix:
- Fix memory leaks in EDP/FDP decoding when receiving some TLVs twice.
- Do not set interface description continuously.
- Use a different Netlink socket for changes and queries.
Signed-off-by: Sebastian Pflieger <sebastian@pflieger.email>
Link: https://github.com/openwrt/openwrt/pull/17570
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit a18385041eaeaf6d98ab79a30ce5fba4e712b765)
047b2efc1348 CMakeLists.txt: bump minimum cmake version
16ff0badbde7 CMakeLists: add support for including ABIVERSION in the library version number
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit e046f8c318618162fcdd768c4a9eadd53c239629)
Increase PKG_RELEASE as follow-up for
("lantiq: fritz_cal_extract with reverse option for AVM FritzBox 7430").
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 4a8717b5e76edbc8e1f63122f8b05685e0b779db)
This implementation of fritz_cal_extract can also retrieve firmware
data stored in reverse byte order, as found in the AVM 7430 device.
This is done by intermediate storage in a buffer presumably large enough
to hold the complete data set. Currently, this buffer size is 128kB + 1kB
(some extra space for skipped data).
In the usual case of "forward" data, this implementation should behave
like the original implementation in all common cases. limit [-l] will
determine the amount of data read and size of buffer allocated.
However, if you are reading reversed data or didn't set a limit, the buffer
may be too small to hold all data. In this case, you can choose a higher
limit [-l] to enforce a sufficient buffer size.
Signed-off-by: Dustin Gathmann <dzsoftware@posteo.org>
Link: https://github.com/openwrt/openwrt/pull/15501
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit b2cac2a9785ada7c30388349f5d9a9bdcff2e730)
Adds patches for the temperature sensor on RTL822x.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry picked from commit d7e82c78d7a2a84404198dab8faf8e142939eb05)
The patch adding temperature sensor support for r8169 has been removed upstream
and the functionality will be added to Realtek PHY instead:
1f691a1fc4
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry picked from commit 0de9999a7819acf74f6adeaa27be363cf72409ab)
fb3c2343b17b add support for an override config directory
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit 44c877f1973b923a2032ce9d880f496a2b077ef6)
10f7996ec294 file: Ignore config file with '.' in name
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 3929ef4c21844189d5db8d14e7e6dc6ba983d571)
Some platforms a single ethernet device for all ports with multiple rx rings
and NAPI threading enabled. In this case, the steering script was limiting
performance by keeping all NAPI threads assigned to the same CPU.
Fix this by assigning each rx queue and the corresponding NAPI task separately.
Additionally, if the number of rx queues is at least as big as the number of
CPUs, skip weight based assignment and distribute the load across all CPUs
directly.
Fixes: https://github.com/openwrt/openwrt/issues/17611
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit acce25b789d40f2d88a2326a7d9921bd1743fe54)
Fixes CPU usage imbalance on some devices using threaded NAPI
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit 67a4aeef6c63e5836bd6b82faf6cc15934869efb)
Bringing up a mesh interface using wpa_supplicant already supports a
per-VIF basic rate selection. Add the same ability when creating a mesh
VIF without wpa_supplicant.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 3deeb7805f69f54b9ab20c0e12f8dd916fec4de1)
cfg80211 is the only supported wireless API
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit d1275392916522d664e710752c517246540cbf73)
This can be used to configure the base mac address from which all
interface mac addresses are derived
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit 00860e485b2ef82c1fafc8e011f3a8965e317bca)
Do not strip the first character from the field name
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit 59dd9cddf9e72d1f9b4ff7e01ae32d2fa99259d9)
Simplifies setting ifname to a different pattern for all affected
interfaces.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit a9ff3ba24b9466d9c06b9a9e1c2e9672bdd9f6f9)
Without this patch, we get the following error:
Mon Dec 23 11:35:44 2024 daemon.err hostapd: nl80211: kernel reports: integer out of range
As updating hostapd would be too complex and requires further testing,
we backport this simple upstream fix instead.
Fixes: https://github.com/openwrt/openwrt/issues/16680
Signed-off-by: Rany Hany <rany_hany@riseup.net>
Link: https://github.com/openwrt/openwrt/pull/17590
Signed-off-by: Petr Štetiar <ynezz@true.cz>
(cherry picked from commit 5ce1af9539da667f62dc3cb426f9ec36e53fb54e)
Link: https://github.com/openwrt/openwrt/pull/17591
Signed-off-by: Robert Marko <robimarko@gmail.com>
Basic rates were not set for mesh-interfaces, resulting in the undesired
behavior where 11s frames might be sent with a rate which was not
configured.
Depending on the driver, the basic rate might also be used to determine
the beacon rate configured to the chip. One such example are MediaTek
MT7915 platforms.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 3ec7f3a512a27f8ca6402954ad2a997176103b4b)
Just one of the devices uses the Marvell MV88E6060 DSA
switch so break this out from the generic kernel config
and into a package selected only by that single device
and probed at boot instead.
The big win is from being able to drop the dsa_core
(~600KB) kernel module out of the common kernel on
devices with no DSA switch.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
(cherry picked from commit 2456a2fd7f72d6afcee4ac9c2eccb312d0b1d36d)
Spaces and tabs are widely used in variable definitions. We have to
remove them to ensure that get_mac_ascii() works properly.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Link: https://github.com/openwrt/openwrt/pull/17262
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 551e04f3c9c063d885ca7a91db36f27f684a3a5c)
The function get_mac_ascii() will fail when there are two or more
same MAC address variable names in the mtd partition. Only retain
the first variable to workaround this rare situation.
Fixes: https://github.com/openwrt/openwrt/issues/17236
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Link: https://github.com/openwrt/openwrt/pull/17262
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 3410ad2f40c085e5db7a71f6ae4b80734826a1e3)
The u-boot LED command "led_loop_done" is missing from the OpenWrt
One NAND flash u-boot. Copy it from the OpenWrt One NOR flash u-boot
default environment to fix this issue.
Fixes: https://github.com/openwrt/openwrt/issues/17310
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Link: https://github.com/openwrt/openwrt/pull/17338
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 5ef71eaafd4e128ec3708a66b5633214427da373)
It seems that the original patch has been manually modified. The
newly added line number is incorrect.
Fixes: c0581520b1c5 ("uboot-mediatek: add Routerich AX3000 support")
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Link: https://github.com/openwrt/openwrt/pull/17338
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 9f97e39a9336e279be7ea1c00c4221ec3f448457)
On some drivers, setting the tx power on the interface is not enough.
Set it for the phy as well.
Fixes: 04fb05914ea7 ("wifi-scripts: add multi-radio config support")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit b795e5cbcffc54e858bc8d3bde0031a2ca32377e)
35bcf68a6297 wifi: mt76: scan: fix setting tx_info fields
4d8d6e2e7710 wifi: mt76: scan: set vif offchannel link for scanning/roc
e354436db440 wifi: mt76: mt7996: use the correct vif link for scanning/roc
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit f11bc4f201e3a4ffec8c1e2083124ebda60dd763)
7a3bcd39ae1f r8169: use helper r8169_mod_reg8_cond to simplify rtl_jumbo_config
e3e9e9039fa6 r8169: align WAKE_PHY handling with r8125/r8126 vendor drivers
330dc2297c82 r8169: improve rtl_set_d3_pll_down
c507e96b5763 r8169: improve __rtl8169_set_wol
83cb4b470c66 r8169: remove leftover locks after reverted change
2cd02f2fdd8a r8169: improve initialization of RSS registers on RTL8125/RTL8126
a3d8520e6a19 r8169: align RTL8126 EEE config with vendor driver
4af2f60bf737 r8169: align RTL8125/RTL8126 PHY config with vendor driver
eb90f876b796 r8169: align RTL8125 EEE config with vendor driver
b8bd8c44a266 r8169: fix inconsistent indenting in rtl8169_get_eth_mac_stats
f75d1fbe7809 r8169: add support for RTL8125D
c4e64095c00c r8169: enable EEE at 2.5G per default on RTL8125B
d64113c6bb5e r8169: remove rtl_dash_loop_wait_high/low
1c105bacb160 r8169: avoid duplicated messages if loading firmware fails and switch to warn level
ac48430368c1 r8169: don't take RTNL lock in rtl_task()
e3fc5139bd8f r8169: implement additional ethtool stats ops
b8bf38440ba9 r8169: enable SG/TSO on selected chip versions per default
854d71c555df r8169: remove original workaround for RTL8125 broken rx issue
1ffcc8d41306 r8169: add support for the temperature sensor being available from RTL8125B
The following patches require backporting additional linux patches:
e2015942e90a r8169: replace custom flag with disable_work() et al
e340bff27e63 r8169: copy vendor driver 2.5G/5G EEE advertisement constraints
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry picked from commit 0eeba04a16fb72b13d90973ef8ba95f0549f973e)
The ARIA block cipher is pretty uncommon in TLS, deactivate it for now.
This saves some space and reduces the possible variations and attack
vectors of mbedtls.
ARIA support was deactivated in OpenWrt 23.05 by default.
Link: https://github.com/openwrt/openwrt/pull/17342
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 3c0ef48bc82cb11edd0b4fdbc4beaa3f95708967)
d996988ae55b libubus: close file descriptor after sending it from a request
afa57cce0aff libubus: add support for using channels
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit f0df6e3a4a4996eca917fa17591b8f1d483dfa30)
It seems that we have some kind of a symbol name conflict which causes
CONFIG_SECCOMP to always be read as y.
Unfortunatelly, I could not figure out what is causing this, but simply
renaming SECCOMP to USE_SECCOMP seems to properly work and leaves the
symbol unset unless arch dependencies are satisfied.
This fixes qoriq and others that dont support seccomp from failing due
to procd-seccomp package being selected to get included but it cannot be
built for them:
ERROR: unable to select packages:
procd-seccomp (no such package):
required by: base-files-1637~52b6c92479[procd-seccomp]
Fixes: 4c65359af49b ("build: fix including busybox, procd and apk/opkg in imagebuilder")
Link: https://github.com/openwrt/openwrt/pull/17048
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit a48ec449ccab0069e84a72837bf06ba543e53aec)
Since the image builder pulls package lists from metadata directly,
add procd and busybox as depdendencies to base-files.
As for the package manager itself, since it can be disabled it needs
to be added directly in the image builder makefile
Fixes: 44598c233dd9 ("build: remove broken dependency of metadata on toplevel .config variables")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit 4c65359af49b6ccecd98987f842db5eba985f64b)
Instead of relying on .config symbols for metadata, alter the DEFAULT
variable of affected packages. Fixes enabling opkg vs apk among others.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit 44598c233dd9a676bc34666968f33f8b9ff4dd0c)
109114146f9c mt76: only enable tx worker after setting the channel
5fe42ec88fd1 mt76: mt7915: ensure that only one sta entry is active per mac address
1884f568ba02 wifi: mt76: do not add wcid entries to sta poll list during MCU reset
71fa9124d107 wifi: mt76: mt7996: fix NULL pointer dereference in mt7996_mcu_sta_bfer_he
eb85bb3fd5bf wifi: mt76: mt7915: fix eifs value on older chipsets
83e4d4a82e65 wifi: mt76: introduce mt792x_config_mac_addr_list routine
b47e20b440ae wifi: mt76: mt7925: fix NULL deref check in mt7925_change_vif_links
3e3c484726f3 wifi: mt76: mt7925: fix wrong band_idx setting when enable sniffer mode
3f1401a0f035 wifi: mt76: mt7925: fix get wrong chip cap from incorrect pointer
eede99f524e8 wifi: mt76: mt7925: fix the invalid ip address for arp offload
c99e4d51b340 wifi: mt76: mt7996: fix overflows seen when writing limit attributes
af983b2543ed wifi: mt76: mt7915: fix overflows seen when writing limit attributes
af494e2dcc94 wifi: mt76: mt7915: exclude tx backoff time from airtime
6f6a1f7cb381 wifi: mt76: mt7996: exclude tx backoff time from airtime
7f65b1b28b4c wifi: mt76: connac: Extend mt76_connac_mcu_uni_add_dev for MLO
1b5e6abc2e7a wifi: mt76: mt7925: Fix incorrect MLD address in bss_mld_tlv for MLO support
72b4688b3912 wifi: mt76: mt7925: Fix incorrect WCID assignment for MLO
6bd2c044e67a wifi: mt76: mt7925: Fix incorrect WCID phy_idx assignment
1c04e9693466 wifi: mt76: mt7925: fix wrong parameter for related cmd of chan info
01e02947bdbf wifi: mt76: mt7925: Fix CNM Timeout with Single Active Link in MLO
b90b1a1dc71b wifi: mt76: mt7925: Enhance mt7925_mac_link_bss_add to support MLO
53ec7a551f17 wifi: mt76: Enhance mt7925_mac_link_sta_add to support MLO
3c99ef40e0e7 wifi: mt76: mt7925: Update mt7925_mcu_sta_update for BC in ASSOC state
285efc6afaec wifi: mt76: mt7925: Update mt792x_rx_get_wcid for per-link STA
e5c0d1289e6c wifi: mt76: mt7925: Update mt7925_unassign_vif_chanctx for per-link BSS
67dcd5c888c4 wifi: mt76: mt7925: Update secondary link PS flow
fd4d6f87072f wifi: mt76: mt7925: Init secondary link PM state
6d972b5b9d6a wifi: mt76: mt7925: Update mt7925_mcu_uni_[tx,rx]_ba for MLO
3acc6cbb9556 wifi: mt76: mt7925: Cleanup MLO settings post-disconnection
0aab0c61ce92 wifi: mt76: mt7925: Properly handle responses for commands with events
15bead1b0041 wifi: mt76: do not hold queue lock during initial rx buffer alloc
732044a949d5 wifi: mt76: mt7925: config the dwell time by firmware
9ba311ec6afa wifi: mt76: mt7921: introduce CSA support
5d12c7404c22 wifi: mt76: mt7921: add rfkill_poll for hardware rfkill
ef965d408b79 wifi: mt76: mt7925: replace zero-length array with flexible-array member
f8563589c72d wifi: mt76: mt7921u: Add VID/PID for TP-Link TXE50UH
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit bff5260d7b2f706f6d32acbb4fbe5f10d7acca5c)
