As started in 19724e28c8 ("ramips: split base-files into
subtargets"), this moves some smaller left-over files to the
appropriate base-files folder of their subtarget:
- /etc/init.d/bootcount
- /etc/uci-defaults/04_led_migration
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
While most of the target's contents are split into subtargets, the
base-files are maintained for the target as a whole.
However, OpenWrt already implements a mechanism that will use (and
even prefer) files in the subtargets' directories. This can be
exploited to make several scripts subtarget-specific and thus save
some space.
In certain cases, keeping files in parent (=target) base-files was
more convenient, and thus no splitting was performed for those.
Note that this will increase overall code lines, but reduce code
per subtarget.
base-files ipk size reduction:
master (mt7621) 60958 B
split (mt7620) 46358 B (- 14.3 kiB)
split (mt7621) 48759 B (- 11.9 kiB)
split (mt76x8) 44948 B (- 15.6 kiB)
split (rt288x) 43508 B (- 17.0 kiB)
split (rt305x) 45616 B (- 15.0 kiB)
split (rt3883) 44176 B (- 16.4 kiB)
Run-tested on:
GL.iNet GL-MT300N-V2 (mt76x8)
D-Link DWR-116 (mt7620)
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
- CMIIT ID: 2019AP2581
- SoC: MediaTek MT7621
- Flash: 16MiB NOR SPI (GigaDevice GD25Q128B)
- RAM: 128MiB DDR3 (ESMT M15T1G1664A)
- Serial: As marked on PCB, 3V3 logic, baudrate is 115200, 8n1
- Ethernet: 3x 10/100/1000 Mbps (switched, 2xLAN + WAN)
- WIFI0: MT7603E 2.4GHz 802.11b/g/n
- WIFI1: MT7612E 5GHz 802.11ac
- Antennas: 4x external (2 per radio), non-detachable
- LEDs: Programmable "power" LED (two-coloured, yellow/blue)
Non-programmable "internet" LED (shows WAN activity)
- Buttons: Reset
INSTALLATION:
Bootloader won't accept any serial input unless "boot_wait" u-boot
environment variable is changed to "on". Vendor firmware (looks like
an illegal OpenWrt fork) won't accept any serial input unless
"uart_en" is set to "1". Tricks to force u-boot to use default
environment do not help as it's restricted in the same way.
With bootloader unlocked the easiest way would be to TFTP the
sysupgrade image or to sysupgrade after loading an initramfs one.
For porting the flash contents were changed externally with an SPI
programmer (after lifting Vcc flash IC pin away from the PCB).
Forum thread [0] indicates that this device is identical to "Xiaomi Mi
Router 4A Gigabit Edition".
[0] https://forum.openwrt.org/t/xiaomi-mi-router-4a-gigabit-edition-r4ag-r4a-gigabit-fully-supported-but-requires-overwriting-spi-flash-with-programmer/36685
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
The Asus RT-AC65P router is identical with the RT-AC85P, but better to make separate images for it.
On both routers the installation can be done also via SSH:
Note: The user/password for SSH is identical with the one used in the
Web-interface.
1. Complete the initial setup wizard.
2. Activate SSH under "Administration" -> "System".
3. Transfer the OpenWrt factory image via scp:
> scp openwrt-ramips-mt7621-asus_rt-ac65p-squashfs-factory.bin admin@192.168.50.1:/tmp
4. Connect via SSH to the router.
> ssh admin@192.168.50.1
5. Write the OpenWrt image to flash.
> mtd-write -i
/tmp/openwrt-ramips-mt7621-asus_rt-ac65p-squashfs-factory.bin -d linux
6. Reboot the router
> reboot
Changelog:
v3: removed [] from filename, rebased to latest master
v2: Rebased to latest master
v1: Initial release
Signed-off-by: Gabor Varga <vargagab@gmail.com>
Based on stock firmware tests, both LAN and WAN ports use the
MAC address from 0x28 on factory partition.
In OpenWrt, this one is already set in DTS. This patch removes the
local bit set in 02_network previously, and adjusts LAN/WAN
addresses as on stock firmware.
Note that in tests we found a MAC address in 0x2e that is the one
in 0x28 plus 1. Since stock firmware does not use it though, we
do not use it either.
Thanks to Chih-Wei Chen for testing this on his device.
ref: https://github.com/openwrt/openwrt/pull/2497
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
UniElec devices are the last ones in ramips target still having
the RAM size in device name although RAM size is auto-detected.
Remove this from device name, compatible, etc., as it's not
required and might be misleading to users and developers adding
device support copying those devices.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This unifies MAC address patch functions and moves them to a
common script. While those were implemented differently for
different targets, they all seem to do the same. The number of
different variants is significantly reduced by this patch.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This moves the almost identical calibration data extraction
functions present multiple times in several targets to a single
library file /lib/functions/caldata.sh.
Functions are renamed with more generic names to merge different
variants that only differ in their names.
Most of the targets used find_mtd_chardev, while some used
find_mtd_part inside the extraction code. To merge them, the more
abundant version with find_mtd_chardev is used in the common code.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
[rebase on latest master; add mpc85xx]
Signed-off-by: David Bauer <mail@david-bauer.net>
All Zbtlink ramips devices except the ZBT-WE1026-5G include the
zbt-/ZBT- prefix in their model name.
This changes ZBT-WE1026-5G to also follow that scheme.
The patch moves some block to keep alphatical order.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This merges three cases with a single switch port.
6t@eth0 and 6@eth0 should be equivalent.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This patch changes wan MAC address setup for youhua,wr1200js
from retrieving it by calculation to reading it from flash.
This has been checked on-device.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
following I-O DATA devices have a MAC address as "wanaddr" for WAN
interface in u-boot-env:
- WN-AC1167GR
- WN-AC733GR3
I replaced MAC address configuration in these devices to omit
address calculation in 02_network.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
ipTIME A3 is a 2.4/5GHz band AC1200 router, based on MediaTek
MT7628AN.
Specifications:
- SoC: MT7628AN
- RAM: DDR2 64MB
- Flash: SPI NOR 8MB
- WiFi:
- 2.4GHz: SoC internal
- 5GHz: MT7612EN
- Ethernet: 3x 10/100Mbps
- Switch: SoC internal
- UART:
- J1: 3.3V, TX, RX, GND (3.3V is the square pad) / 57600 8N1
Installation via web interface:
1. Flash **initramfs** image through the stock web interface.
2. Boot into OpenWrt and perform sysupgrade with sysupgrade image.
Revert to stock firmware:
1. Perform sysupgrade with stock image.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Hardware:
SoC: MT7621A
Flash: 32 MiB
RAM: 512 MiB
Ethernet: built-in switch
USB: 1x USB3.0
SATA: ASM1060, 1 SATA port
Flash instruction (TFTP):
1. Set PC to fixed ip address 192.168.173.22
2. Download *-sysupgrade.bin image and rename it to firmware.img
3. Start a tftp server with the image file in its root directory
4. Turn off the router
5. Turn on router,press the reset button and wait ~15 seconds
6. Release the reset button and after a short time
the firmware should be transferred from the tftp server
7. Wait ~3 minutes to complete recovery.
Signed-off-by: Qi Jiang <rushx@live.cn>
[squash commits, add label-mac-device, fix sign-off style]
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
This replaces deprecated backticks by more versatile $(...) syntax.
While at it, remove some useless cat commands and deprecated
egrep commands.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The EnGenius ESR600 is a dual band wireless router with a 4-port gigabit
Ethernet switch, a gigabit Ethernet WAN port and a USB port.
Specification:
- Bootloader: U-Boot
- SoC: MediaTek MT7620A (600 MHz)
- Flash: 16MB, Macronix MX25L12845E
- RAM: 64MB, Nanya NT5TU32M16DG-AC
- Serial: 115200 baud, no header, 3.3V
J2: Vcc (arrow), Gnd, Tx, Rx
- USB: USB 2, 5V
- Ethernet: 5 x 1 Gb/s 4 LAN 1 WAN, Atheros AR8327
- WiFi0: 5 GHz 802.11 b/g/n Ralink RT5592N
300 Mb/s, 2T2R
- WiFi1: 2.4 GHz 802.11 b/g/n integrated
300 Mb/s, 2T2R
- Antennas: 2 per radio, internal
- LEDs: 1 programmable power (amber)
2 programable radio (blue)
1 programable WPS-5G (blue)
1 non-programable WAN activity (blue)
1 unconfigured WPS-2.4G (amber)
- Buttons: GPIO: Reset, WPS
Installation:
Use the OEM web interface to install the ...-factory.dlf image.
Use the OpenWRT ...-sysupgrade.bin image for future upgrades.
The J2 serial port can be accessed either by soldering in a header,
standard 0.1" spacing, or by using pogo-pins against the back side.
As configured by the OEM, the U-Boot boot delay is short, however quickly
typing "1" leads to the U-Boot "System load Linux to SDRAM via TFTP"
prompt. The TFTP client is configured by default with
client: 192.168.99.9
server: 192.168.99.8
filename: uImageESR600
It will load an OpenWRT initramfs kernel with this method.
Known issues:
1) Only the ports externally labeled WAN, LAN3 and LAN4 are operational.
LAN1 and LAN2 do not appear to power up. This issue is also present
in the Lava LR25G001.
2) The amber WPS-2.4G LED, in the same lightguide as the blue WPS-5G LED,
is not configured in the Device Tree specification.
3) The blue WAN activity LED is not configured in the Device Tree
specification as this causes the AR8327 switch to fail to initialize.
Signed-off-by: Nick Briggs <nicholas.h.briggs@gmail.com>
[merge conflict in 02_network]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
SoC: Mediatek MT7621A
CPU: 4x 880Mhz
Cache: 32 KB I-Cache and 32 KB D-Cach
256 KB L2 Cache (shared by Dual-Core)
RAM: DDR3 512MB 16bits BUS
FLASH: 16MB
Switch: Mediatek Gigabit Switch (2 x LAN, 1 x WAN)
POE: (1x PD, 2x PSE)
USB: 1x 3.0
PCI: 3x Mini PCIe (3 USB2.0 + 2 x UIM interface)
GPS: Quectel L70B
SIM: 2 Slots
BTN: Reset
LED: - Power
- Ethernet
- Wifi
- USB
UART: UART is present as Pads with throughholes on the PCB.
They are located on left side.
3.3V - RX - GND - TX / 57600-8N1
3.3V is the square pad
Installation
------------
The stock image is a modified openwrt and can be overflashed via sysupgrade -F
Signed-off-by: Daniel Danzberger <daniel@dd-wrt.com>
[merge conflict in mt7621.mk]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
SoC: MediaTek MT7621AT dual-core @ 880MHz
RAM: 256M (Winbond W632GG6KB-1)
FLASH: 128MB (Macronix MX30LF1G18AC-TI)
WiFi: - 2.4GHz MediaTek MT7615N bgn
- 5GHz MediaTek MT7615N nac
Switch: SoC integrated Gigabit Switch (4 x LAN, 1 x WAN)
USB: 1 x USB 3.1 (Gen 1)
BTN: Reset, WPS
LED: - Power (blue)
- 5Ghz (blue)
- 2.4GHz (blue)
- Internet (blue)
- 4x LAN (blue)
(LAN/WAN leds are not controllable by GPIOs)
UART: UART is present as Pads marked J4 on the PCB.
3.3V - TX - RX - GND / 57600-8N1
3.3V is the square pad
MAC: The MAC address on the router-label matches the MAC of
the 2.4 GHz WiFi.
LAN and WAN MAC are identical: MAC_LABEL+4
5 GHz WiFi MAC: also MAC_LABEL+4
Installation
------------
Via U-Boot tftpd:
Switch on device, within 2s press reset button and keep pressed
until power LED starts blinking slowly.
Upload factory image via tftp put, the router's ip is 192.168.1.1
and expects the client on 192.168.1.75.
The images also work on the Asus RT-AC65P models as tested by Gabor.
Signed-off-by: Birger Koblitz <mail@birger-koblitz.de>
Tested-by: Gabor Varga <vargagab@gmail.com>
[fixed Asus -> ASUS in DTS]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
SoC: MediaTek MT7621AT dual-core @ 880MHz
RAM: 256M (Nanya NT5CC128M)
FLASH: 16MB (Macronix MX25L12835F)
WiFi: - 2.4GHz MediaTek MT7615N bgn
- 5GHz MediaTek MT7615N nac
Switch: SoC integrated Gigabit Switch (4 x LAN, 1 x WAN)
USB: No
BTN: Reset, WPS
LED: 4 red LEDs, indistinguishable when casing closed
UART: UART is present as Pads marked J1 on the PCB.
3.3V - RX - GND - TX / 57600-8N1
3.3V is the square pad
Installation
------------
Update the factory image via the OEM web-interface
(by default:http://192.168.1.1)
The sysupgrade image can be installed via TFTP from
the U-Boot bootloader. Connect ethernet port 2.
Signed-off-by: Birger Koblitz <mail@birger-koblitz.de>
[flash node rename, EDIMAX -> Edimax, complete device model name]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This patch adds the label MAC address for several devices in
ramips.
Some devices require setting the MAC address in 02_network:
For the following devices, the netif device can be linked in
device tree, but the MAC address cannot be read:
- cudy,wr1000
- dlink,dir-615-d
- dlink,dir-615-h1
- dlink,dir-860l-b1
- glinet,gl-mt300a
- glinet,gl-mt300n
- glinet,gl-mt750
- vocore,vocore2
- vocore,vocore2-lite
- zbtlink,zbt-we1326
- zbtlink,zbt-wg3526
For the following devices, label MAC address is tied to lan or
wan, so no node to link to exists in device tree:
- dlink,dir-510l
- dlink,dwr-116-a1
- dlink,dwr-118-a1
- dlink,dwr-118-a2
- dlink,dwr-921-c1
- dlink,dwr-922-e2
- all hiwifi devices
- lava,lr-25g001
- xiaomi,mir3p
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
So far, MAC address setup for those devices has been using local
addresses although additional MAC addresses are available on flash.
On device, we found the following situation:
position Y1 Y1S
0x4 *:d4 *:e4
0x8004 *:d6 *:e8
0x28 *:d4 *:e4
0x2e *:d7 *:eb
Since 0x4 and 0x28 yield the same address, the former was set for
ðernet in DTS. However, the typical location on this
architecture is 0x28, so this patch changes that.
For further setup in 02_network, the local bit for lan_mac is
removed, so the address from ðernet is used at all. For wan_mac,
instead of calculating an address with local bit set, this patch
exploits the previously unused address in 0x2e.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This patch changes wan MAC address setup from retrieving it by
calculation to reading it from flash.
Changes are limited to cases where on-device check was possible.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
[fix mac for newifi-d1; drop adslr,g7 because it's unlikely for
vendor to specifically use 2.4g mac as wan_mac]
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
In 555ca422d1 ("ramips: fix D-Link DIR-615 H1 switch port
mapping"), port setup for dir-615-h1 was changed without removing
the old one. This was working as the new one was triggered earlier
than the old one.
(In the meantine, changed sorting during ramips rename patches
actually inversed that order.)
Anyway, just remove the wrong case now.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
ARC FreeStation5 is present twice in MAC address setup.
From older commits/changes, it is not possible to reconstruct
the correct choice only by reading the annotations.
Thus, remove the second case and keep the first one, so behavior
stays the same (as nobody seems to have complained about it).
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This patch removes unnecessary MAC address setup statements in
ramips' 02_network by doing several optimizations:
1. For the following devices, lan_mac was set up with
mtd_get_mac_binary although the same address was set in DTS.
The lan_mac statement is removed in 02_network, but
wan_mac is kept:
- mercury,mac1200r-v2
- phicomm,k2g
- skylab,skw92a
- wiznet,wizfi630a
2. For the following devices, wan_mac was set up with
mtd_get_mac_binary although the same address was set in DTS.
The wan_mac statement is removed in 02_network, no
lan_mac is present:
- buffalo,whr-g300n
- glinet,gl-mt300n-v2
- zyxel,keenetic-start
3. For the following device, lan_mac and wan_mac were set up
with mtd_get_mac_binary to the same address as set in DTS.
Both statements are removed in 02_network:
- buffalo,whr-600d
4. For some devices, it was possible to move setup from 02_network
to DTS by introducing previously missing mtd_mac_address:
- buffalo,whr-1166d
- buffalo,whr-300hp2
- buffalo,wsr-600dhp
- ohyeah,oy-0001
- planex,vr500
5. For one device, mtd_mac_address was just wrong and overwritten
by 02_network. Put the correct value in DTS and remove redundant
statement in 02_network:
- asus,rt-ac57u
6. For one device, MAC address defined in DTS is exchanged together
with lan_mac/wan_mac setup in 02_network, so that cases in
02_network can be merged:
- phicomm,k2p
For some devices, an empty case has to be used to prevent them
from falling into the default case and have
WAN address = eth0 address + 1 set to them.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This patch does the following things:
1. mark u-boot-env writable
2. add bootcount support
Currently, u-boot has a flag_boot_success env variable to reset.
Also reset it in our firmware to follow the behavior in vendor's
firmware.
3. disable usb support
This router doesn't have usb port at all.
4. increase spi clock to 40MHz
5. fix pinmux groups
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
As Netgear uses the same image for R6260, R6350 & R6850
we can merge device tree files and generate separate
images for each device.
Signed-off-by: Christoph Krapp <achterin@googlemail.com>
[add missing WiFi compatible string, fix network
configuration]
Signed-off-by: David Bauer <mail@david-bauer.net>
There are currently the following issues present for the Netgear R6220,
R6350 and WNDR3700 v5:
- LAN and WAN MAC-addresses are inverted
- WAN MAC-address is off. It are +2 compared to the LAN MAC-address
(R6350 only)
- Switchport order is inverted in LuCi
This commit fixes both these issues by assigning correct MAC-addresses
to LAN and WAN interfaces and defining the switchports with the correct
labels.
Signed-off-by: David Bauer <mail@david-bauer.net>
This commit switches the default trigger for the WiFi LED from a netdev
trigger on "wlan0" to a wireless-phy based trigger. THis allows the LED
to work, even when the wireless interface is not named "wlan0" without
modifiying the LED settings.
Signed-off-by: David Bauer <mail@david-bauer.net>
SoC: MT7621AT
RAM: 256MB
Flash: 16M SPI
Ethernet: 5x GE ports
WiFi: 2.4G: MT7615N
5G: MT7615N
Flash instruction:
1.Modify the file to linux.bin
2.Set up FTP service
3.Computer settings fixed IP: 192.168.179.50 255.255.255.0
4.Turn on the power and press and hold the reset button until the indicator light is on for about 5 seconds.
Signed-off-by: Zhenjian Zhang <itdesk.zhang@gmail.com>
[fix mac location]
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
This change the switch settings for:
HC5661: 4 lan ports + 1 wan port
Y1S: 2 lan ports(G port) + 2 lan ports(E port) + 1 wan port
Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
netdev on eth0.2 can't show link status of wan port because eth0 is
connected to builtin switch and is always link up. Use swconfig
trigger instead.
Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
[redo commit message]
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
ipTIME A604M is a 2.4/5GHz band AC1200 router, based on MediaTek
MT7628AN.
Specifications:
- SoC: MT7628AN
- RAM: DDR2 64MB
- Flash: SPI NOR 8MB
- WiFi:
- 2.4GHz: SoC internal
- 5GHz: MT7612EN
- Ethernet: 5x 10/100Mbps
- Switch: SoC internal
- UART:
- J1: 3.3V, TX, RX, GND (3.3V is the square pad) / 57600 8N1
Installation via web interface:
1. Flash **initramfs** image through the stock web interface.
2. Boot into OpenWrt and perform sysupgrade with sysupgrade image.
Revert to stock firmware:
1. Perform sysupgrade with stock image.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
This commit made the following changes to sync all bootcount scripts:
1. use boot() instead of start()
This script only needs to be executed once when boot is complete.
use boot() to make this explicit.
2. drop sourcing of /lib/functions.sh
This is aready done in /etc/rc.common.
3. ramips: replace board name checking with a case
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
This changes size and offset set for WiFi caldata extraction and
MAC address adjustment to hexadecimal notation.
This will be much clearer for the reader when numbers are big, and
will also match the style used for mtd-cal-data in DTS files.
Since dd cannot deal with hexadecimal notation, one has to convert
back to decimal by simple $(($hexnum)).
Acked-by: Alexander Couzens <lynxis@fe80.eu>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This changes the offsets for the MAC address location in
mtd_get_mac_binary* and mtd_get_mac_text to hexadecimal notation.
This will be much clearer for the reader when numbers are big, and
will also match the style used for mtd-mac-address in DTS files.
(e.g. 0x1006 and 0x5006 are much more useful than 4102 and 20486)
Acked-by: Alexander Couzens <lynxis@fe80.eu>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Revert "mac80211: add new minstrel_ht patches to improve probing on mt76x2" (9861050b85)
Revert "kernel: use bulk free in kfree_skb_list to improve performance" (98b654de2e)
Revert "ramips: add preliminary support for WIO ONE" (085141dc5b)
Revert "ramips: add preliminary support for SGE AP-MTKH7-0006 developer board" (b1db6d0539)
Revert "build: use config.site generated by autoconf-lean, drop hardcoded sitefiles" (363ce4329d)
Revert "toolchain: add autoconf-lean" (fdb30eed03)
Revert "build: allow overriding the filename on the remote server when downloading" (6fa0e07758)
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Lan and Wan addresses are swapped compared to the original firmware.
This patch fixes this problem
Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
In commit d93969a13a ("ramips: Improve compatible for TP-Link
Archer devices") and subsequent ones, names of several devices
in ramips have been changed.
Since LED names are frequently invoked by $boardname, this has
broken LED setup in 01_leds, as $boardname and prefix in DTS
do not match anymore.
This patch updates device name prefixes for LEDs in DTS files,
and provides a migration script.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
HiWiFi HC5761A is an "MT7628AN variant" of HC5761
Specifications:
- MediaTek MT7628AN 580MHz
- 128 MB DDR2 RAM
- 16 MB SPI Flash
- 2.4G MT7628AN 802.11bgn 2T2R 300Mbps
- 5G MT7610EN 802.11ac 433Mbps
- 3x 10/100 Mbps Ethernet
Flash instruction:
1. Get SSH access to the router
2. SSH to router with `ssh -p 1022 root@192.168.199.1`, The SSH password is the same as the webconfig one
3. Upload OpenWrt sysupgrade firmware into the router's `/tmp` folder with SCP
4. Run `mtd write /tmp/<filename> firmware`
5. reboot
Known bug:
- SD slot does not work (See PR 1500)
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
HC5661A:
- Fix pinctrl
- Fix image size (15808k)
- Use switch trigger for WAN LED
Both:
- Use tpt LED trigger for wireless
- Explicitly disable USB nodes
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
There's an empty case in 02_network introduced by last commit. Drop it.
Fixes: ee650ba46c ("ramips: remove needless setting of lan_mac to eth0 in 02_network")
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
This removes superfluous lines like
lan_mac=$(cat /sys/class/net/eth0/address)
Since lan_mac only sets the MAC address for eth0.1, these lines
can be safely removed as the address will be inherited from eth0
anyway.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The vast majority of devices labels "factory" partition with lower
case. Convert the small fraction with capital letter to that and
merge another case in 02_network.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This just merges some duplicate definitions and consolidates lines.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: Chuanhong Guo <gch981213@gmail.com> [merge duplicated
cases for phicomm k2p]
