Package bnxt_en kernel module for Broadcom NetXtreme-C/E based Ethernet
network chips like BCM573xx and BCM574xx.
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17301
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This reverts commit 1cea889c96.
This reverts commit 5fd86d66c1.
The patch is causing build servers to fail. Revert it for now.
Signed-off-by: John Crispin <john@phrozen.org>
This option enables support for monochrome LEDs that are grouped into multicolor
LEDs which is useful in the case where LEDs of different colors are physically
grouped in a single multi-color LED and driven by a controller that doesn't have
multi-color support.
Signed-off-by: Jonathan Brophy <professor_jonny@hotmail.com>
Link: https://github.com/openwrt/openwrt/pull/16397
Signed-off-by: John Crispin <john@phrozen.org>
This commit adds the Linux kernel mainline driver "leds-ktd202x" for the
KinetIC KTD2026 and KTD2027 RGB/RBGW controller with I2C interface that was
introduced in kernel version 6.7, last changed in mainline on 2024-05-31.
At least the Acer Connect Vero W6m (a variant of the Acer Predator Connect
W6 without 2.5G eth1 port, usb3 port, and the 6 on-board gpio RGB LEDs) is
equipped with a KTD2026 (and a single RGB LED attached to it used by the
stock firmware as status LED), and maybe other router devices also are.
Signed-off-by: George Oldfort <openwrt@10099.de>
Link: https://github.com/openwrt/openwrt/pull/16860
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Change the dependency on the kmod-media-controller from depends to
select.
Fixes: 1095925246 ("kernel: add kmod-media-controller dependency for kmod-usb-audio")
Link: https://github.com/openwrt/openwrt/pull/17058
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Netatalk v4 reintroduces AppleTalk and this module is required for
layer 3 protocol support.
Module was removed in kernel 4.14 for OpenWrt 18.06 (commmit
14a0131, 22/02/2018). At the time nothing used it as Netatalk v3
did not support AppleTalk.
Not building ipddp feature/module like it was in the past, as
recommended by upstream Netatalk maintainers.
Signed-off-by: Antonio Pastor <antonio.pastor@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16979
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
These packages are needed for the stm32/stm32mp1 subtarget.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/16716
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The snd-usb-audio drivers uses media controller if media controller is set.
So add kmod-media-controller as dependency.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/16716
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
It is needed for the stm32/stm32mp1 subtarget.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/16716
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
It is needed for the stm32/stm32mp1 subtarget.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/16716
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
It is needed for the stm32/stm32mp1 subtarget.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/16716
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
It is needed for the stm32/stm32mp1 subtarget.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/16716
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
It is needed for the stm32/stm32mp1 subtarget.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/16716
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
It is needed for the stm32/stm32mp1 subtarget.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/16716
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Disable drm-i915 module for target x86/geode.
Fixes: 77cfe8f ("x86: make i915 as a kmod with required firmware")
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/16977
Signed-off-by: Robert Marko <robimarko@gmail.com>
i915 driver requires to load correct firmware to work on latest x86
GPU, it is more reasonable to make it as a kernel module, so that
initramfs is not required, and it can also save some space from the
kernel image comparing being a built-in driver
Signed-off-by: Joe Zheng <joe.zheng@intel.com>
Link: https://github.com/openwrt/openwrt/pull/16276
Signed-off-by: Robert Marko <robimarko@gmail.com>
Package kmod-drm-panel-mipi-dbi as well as modules it depends on in
order to support a wide range of MIPI DBI complaint SPI-connected
TFT panels.
See https://github.com/notro/panel-mipi-dbi/ for more information on
how to use specific panels.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Package gs_usb CAN driver, which is for Geschwister Schneider and
bytewerk.org candleLight compatible USB/CAN interfaces.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Drop limitation on depending on only armv8 for armsr target as those
module should support both 32 and 64 bits systems.
Only thunderx-net actually require 64 bit systems.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add INET diag socket monitoring interface module for MultiPath TCP.
It allows using native Linux socket diagnostic tools such as 'ss' for
Multipath TCP connections.
Co-authored-by: Rodrigo B. de Sousa Martins <rodrigo.sousa.577@gmail.com>
Signed-off-by: sKy King <29267720+sKyissKy@users.noreply.github.com>
Link: https://github.com/openwrt/openwrt/pull/12884
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Set the boot flag for the igc, mlx4-core, and mlx5-core network device drivers
to load them at a more early stage of the boot process.
This is required for network drivers whose network interface PCI paths are set
via ucidef_set_network_device_path inside the 02_network script since it is
called after kernel modules are loaded from modules-boot.d but before they are
loaded from the modules.d directory.
Signed-off-by: Til Kaiser <mail@tk154.de>
Link: https://github.com/openwrt/openwrt/pull/16560
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The swconfig-based b53 driver for the BCM53128 switch stopped working
after commits b2cfed48f6 (Revert "swconfig: fix Broadcom b53 support")
and e4e410733f (kernel: export switch_generic_set_link() symbol). This
rendered the 8 LAN ports of the EdgeSwitch 8XP non-functional, so the
image compilation for the device was disabled (5a1d7d8c1b).
This commit adds the kmod-dsa-b53-mdio and kmod-dsa-b53 packages
with the upstream B53 DSA driver, replacing the swconfig-based
kmod and kmod-switch-bcm53xx-mdio downstream ones that are not used by
any other device.
The 8 LAN ports of the EdgeSwitch 8XP are usable again. The 02_network
init script has been updated with the new DSA interfaces lan1 .. lan8.
Image building has been reenabled for the device, adding the usual DSA
incompatibility notice.
Tested on a Ubiquiti EdgeSwitch 8XP.
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
Link: https://github.com/openwrt/openwrt/pull/11680
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This solution that is needed for some routers to provide proper
LED activity when controlled directly by the MV88E6xxx switch,
has just been merged in upstream Linux.
Make this patch 901 as other backports from earlier kernels
are in patch 896 and this is the first free number after
that.
Patch offsets in pending patches are augmented as part of
the refresh.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
RmNet driver provides a transport agnostic MAP (multiplexing and
aggregation protocol) support in embedded module. Module provides
virtual network devices which can be attached to any IP-mode
physical device.
This is commonly used on Qualcomm based modems for data aggregation.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
1. Remove outdated symbol CONFIG_USB_OHCI_ATH79.
The ath79 OHCI USB was already supported by the generic driver
kmod-usb-ohci. And this kernel symbol has been dropped since
upstream commit:
53d473fc1e38 ("usb: host: Remove the deprecated ATH79 USB host config options")
2. Add ath79 USB phy package to the OHCI dependencies.
Both EHCI and OHCI require it on the ath79 target.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Link: https://github.com/openwrt/openwrt/pull/16380
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Compile LED support to swconfig and phy modules
Signed-off-by: Oskari Lemmela <oskari@lemmela.net>
Link: https://github.com/openwrt/openwrt/pull/15926
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add support for building DSA switch drivers as kernel modules.
Signed-off-by: Oskari Lemmela <oskari@lemmela.net>
Link: https://github.com/openwrt/openwrt/pull/15926
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add support for building multiple phy drivers as kernel modules
Signed-off-by: Oskari Lemmela <oskari@lemmela.net>
Link: https://github.com/openwrt/openwrt/pull/15926
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add support for building both upstream and downstream ag71xx drivers
as modules.
Signed-off-by: Oskari Lemmela <oskari@lemmela.net>
Link: https://github.com/openwrt/openwrt/pull/15926
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* Adds the x86_64 dependency for mlxsw_core
* Removes the redundant mlxsw_core dependency
from mlxsw-minimal and mlxsw-spectrum
* Removes the DCB configuration symbols because
they were moved into the generic configuration
Signed-off-by: Til Kaiser <mail@tk154.de>
Link: https://github.com/openwrt/openwrt/pull/15362
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This commit adds the missing x86 dependency for
the Mellanox mlxcpld LED driver.
Signed-off-by: Til Kaiser <mail@tk154.de>
Link: https://github.com/openwrt/openwrt/pull/15362
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
6.1.103 and 6.6.44 introduced breakage complaining about missing mtd_test.ko
for some targets.
Signed-off-by: Zxl hhyccc <zxlhhy@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16093
Signed-off-by: Robert Marko <robimarko@gmail.com>
Compilation of mtd_test.ko should be added only for kernel 6.6 or above.
Fixes 26df88a ("kernel: Add kmod-mfd-test")
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/16085
Signed-off-by: Robert Marko <robimarko@gmail.com>
6.6.44 introduced breakage complaining about missing mtd_test.ko
for some targets.
Signed-off-by: John Audia <therealgraysky@proton.me>
Link: https://github.com/openwrt/openwrt/pull/16061
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add the package for the Pixart PAC7302 USB Camera Driver kernel module.
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15886
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Package the sctp_diag.ko file which already gets build when kmod-sctp
and kmod-inet-diag are selected.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Link: https://github.com/openwrt/openwrt/pull/15833
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Package the mfd-core.ko kernel module. It is selected by the
kmod-hwmon-gsc already.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Link: https://github.com/openwrt/openwrt/pull/15833
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
The mtd_nandbiterrs.ko kernel module was added with kernel 3.7. We
should package it like the other test modules.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Link: https://github.com/openwrt/openwrt/pull/15833
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
kxxhash_generic.ko is a soft dependency of kmod-fs-btrfs, but we did not
package it. Extract the kmod-lib-xxhash and then package
xxhash_generic.ko.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Link: https://github.com/openwrt/openwrt/pull/15833
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
The kmod-fs-btrfs package has a soft dependency to kmod-crypto-blake2b
The CONFIG_BTRFS_FS kernel build option selects CONFIG_CRYPTO_BLAKE2B,
but we did not package it before.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Link: https://github.com/openwrt/openwrt/pull/15833
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
The kernel provides two variants of the lz4 compression a normal version
and a high compression mode version. The old kmod-lib-lz4 package
contained the normal version plus one part of the lz4hc version. There
was already code which selected the kmod-lib-lz4hc package which did
not exists.
I split this into 3 packages. kmod-lib-lz4 and kmod-lib-lz4hc for the
normal the and high compression algorithm which contain the specific
code and the kmod-lib-lz4-decompress which contains the common
decompressor.
New we are also packaging lz4hc.ko
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Link: https://github.com/openwrt/openwrt/pull/15833
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
The nf_dup_ipv4.ko and nf_dup_ipv6.ko kernel module were packaged by
kmod-ipt-tee and kmod-nft-dup-inet at the same time. Extract them into a
separate package used by both.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Link: https://github.com/openwrt/openwrt/pull/15833
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
