Getting ready for the next release.
Signed-off-by: Paul Spooren <mail@aparcar.org>
[rmilecki: tested on GT-AC5300: boot, sysupgrade & 940 Mbps NAT]
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
bmips target is now more stable and it's time to start generating buildbot
images in order to receive a wider testing, which will be essential to replace
bcm63xx target in the future.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
BMIPS is a generic arch that can be used for multiple Broadcom SoCs, each one
with its own specific drivers, so instead of having a huge kernel supporting
all of them, let's switch to a subtarget per SoC like other OpenWrt targets.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Add BCM6328 and BCM6358 LED kernel modules.
This allows selecting the LED controllers only for those devices using them.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Sercomm SHG2500 is a BCM63168 with 128M of RAM, 256M of NAND, an external
BCM53124S switch for the LAN ports and internal/external Broadcom wifi.
LEDs are connected to an external MSP430G2513 MCU controlled via SPI.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Make use of sercomm-pid script for generating the Sercomm PID, which avoids
having to add an array of hex bytes for every new Sercomm device.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SERCOMM_VERSION is ambiguous and it should be more clear that it refers to the
version used for the filesystem.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Instead of passing an array of hex bytes for the Sercomm PID we can now use
the --pid-file parameter.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Hardware
--------
SoC: NXP P1010 (1x e500 @ 800MHz)
RAM: 256M DDR3 (2x Samsung K4B1G1646G-BCH9)
FLASH: 32M NOR (Spansion S25FL256S)
BTN: 1x Reset
WiFi: 1x Atheros AR9590 2.4 bgn 3x3
2x Atheros AR9590 5.0 an 3x3
ETH: 2x Gigabit Ethernet (Atheros AR8033 / AR8035)
UART: 115200 8N1 (RJ-45 Cisco)
Installation
------------
1. Grab the OpenWrt initramfs, rename it to ap3715.bin. Place it in
the root directory of a TFTP server and serve it at
192.168.1.66/24.
2. Connect to the serial port and boot the AP. Stop autoboot in U-Boot
by pressing Enter when prompted. Credentials are identical to the one
in the APs interface. By default it is admin / new2day.
3. Alter the bootcmd in U-Boot:
$ setenv ramboot_openwrt "setenv ipaddr 192.168.1.1;
setenv serverip 192.168.1.66; tftpboot 0x2000000 ap3715.bin; bootm"
$ setenv boot_openwrt "sf probe 0; sf read 0x2000000 0x140000 0x1000000;
bootm 0x2000000"
$ setenv bootcmd "run boot_openwrt"
$ saveenv
4. Boot the initramfs image
$ run ramboot_openwrt
5. Transfer the OpenWrt sysupgrade image to the AP using SCP. Install
using sysupgrade.
$ sysupgrade -n <path-to-sysupgrade.bin>
Signed-off-by: David Bauer <mail@david-bauer.net>
The kernel is already compressed with XZ by the bootwrapper, thus we
gain nothing by compressing it a second time.
Signed-off-by: David Bauer <mail@david-bauer.net>
The bootpage for the second core is placed by U-Boot in the upper 128k
of syste-memory.
This could either be a reserved-area or deducted from the total
system-memory. As only the latter is parsed by the bootwrapper, reduce
the available system memory for linux in order to preserve the bootpage
from being overwritten.
Signed-off-by: David Bauer <mail@david-bauer.net>
Kernel 5.10 builds currently fail because the patch for using the
simpleImage bootwrapper were not added to 5.10.
Signed-off-by: David Bauer <mail@david-bauer.net>
This adds properties to PCIe as well as ethernet nodes which are
normally added by the Extreme Networks U-Boot.
Signed-off-by: David Bauer <mail@david-bauer.net>
This adds properties normally filled by U-Boot. Also it fixes the node
name, which is incorrectly referring to a P1010 core.
Signed-off-by: David Bauer <mail@david-bauer.net>
This is normally filled by U-Boot. Prevents double-printing of early
console messages. Also enables debug-output by the zImage wrapper.
Signed-off-by: David Bauer <mail@david-bauer.net>
Prevent the BBT translation layer from remapping the UBI used for
storing rootfs.
Explicitly define the number of blocks reserved for remapping.
Signed-off-by: David Bauer <mail@david-bauer.net>
Fix mis-typed DEVICE-MODEL in mk file for EnGenius EWS2910P.
Signed-off-by: Raylynn Knight <rayknight@me.com>
[ fix wrong SoB format and improve commit title/description ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
They add NVMEM layouts support. It allows handling NVMEM content
independently of NVMEM device access.
Skip U-Boot env data patch for now as it break our downstream MAC hacks.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
We need to reset KERNEL_LOADADDR if we use it on a per-device base.
Otherwise the previous value will be kept in case a device doesn't
define KERNEL_LOADADDR and relies on the default.
Move initializing KERNEL_LOADADDR to target/linux/mediatek/image/Makefile,
similar to how it's done also on the ramips target.
This fixes image size related breakage on devices which rely on the
default value of KERNEL_LOADADDR.
While at it use 0x48000000 which is more common than the previous default
0x44000000 for the filogic subtarget.
Fixed: e7c399bee6 ("filogic: add support for ASUS TUF-AX4200")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
MAC drivers don't use SGMII in-band autonegotiation unless told to do so
in device tree using 'managed = "in-band-status"'. When using MDIO to
access a PHY, in-band-status is unneeded as we have link-status via
MDIO. Switch off SGMII in-band autonegotiation using magic values.
Reported-by: Chen Minqiang <ptpt52@gmail.com>
Reported-by: Chukun Pan <amadeus@jmu.edu.cn>
Reported-by: Yevhen Kolomeiko <jarvis2709@gmail.com>
Tested-by: Yevhen Kolomeiko <jarvis2709@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Some vendor bootloaders do weird things with those PHYs which result in
link modes being reported wrongly. Start from a clean sheet by resetting
the PHY.
Reported-by: Yevhen Kolomeiko <jarvis2709@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add dynamic interface mode update for the rtl8221 phy to match various
wire speeds. 10M/100M/1000M use SGMII, 2500M uses 2500Base-X.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Refresh patches which were no longer applying cleanly after a recently
added SFP quirk.
Fixes: 658b45ce48 ("generic: add quirk for HG MXPD-483II 2500M fiber SFP")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This reverts commit aa4a9058fb.
The assumption the bootloader fills out the MAC-address is not
correct. The MAC-address has to be set from userspace based on
information found in the device_id partition.
Signed-off-by: David Bauer <mail@david-bauer.net>
The HG MXPD-483II 1310nm SFP module is meant to operate with 2500Base-X,
however, in their EEPROM they incorrectly specify:
Transceiver type : Ethernet: 1000BASE-LX
...
BR, Nominal : 2600MBd
Use sfp_quirk_2500basex for this module to allow 2500Base-X mode anyway.
https://forum.banana-pi.org/t/bpi-r3-sfp-module-compatibility/14573/60
X-Patchwork-Id: 13197378
X-Mailing-List: netdev@vger.kernel.org
X-Patchwork-Delegate: kuba@kernel.org
Reported-by: chowtom <chowtom@gmail.com>
Tested-by: chowtom <chowtom@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add support for OrayBox X1. It is a 802.11n router, based on MediaTek MT7628N.
Specifications:
SoC: MediaTek MT7628N (580MHz)
RAM: 64 MiB
Flash: 16 MiB NOR (Winbond W25Q128JVSIQ)
Wireless: 802.11b/g/n 2x2 2.4GHz (Built In)
Ethernet: 1x 100Mbps only
USB: 1x USB Type-A 2.0 Host Port
Button: 1x "Reset" button
LED: 1x Blue LED + 1x Red LED + 1x White LED
Power: 5V Micro-USB input
Manufacturer Page:
https://pgy.oray.com/router/x1.html/parameter
Flash Layout:
0x000000000000-0x000000030000 : "u-boot"
0x000000030000-0x000000040000 : "kpanic"
0x000000040000-0x000000050000 : "factory"
0x000000050000-0x000000fe0000 : "firmware"
0x000000fe0000-0x000000ff0000 : "bdinfo"
0x000000ff0000-0x000001000000 : "reserve"
Install via SSH:
Original firmware is based on OpenWRT, but SSH is not start by default,
You should enable it first
1. Login into web admin (10.168.1.1), default password is 'admin'
2. Open the following link, and the result should be {"code":0};
SSH is now started, username is root, password is same as web admin password
http://10.168.1.1/cgi-bin/oraybox?_api=ssh_set&enabled=1
4. You can flash firmware via mtd: mtd write /tmp/firmware_image.bin firmware
Signed-off-by: Bin We <me@udp.pw>
The nand driver normally while waiting for the device to become ready;
this is normally fine, but xway_nand holds the ebu_lock spinlock, and
this can cause lockups if other threads which use ebu_lock are
interleaved. Fix this by waiting instead of polling.
This mainly showed up as crashes in ath9k_pci_owl_loader (see
https://github.com/openwrt/openwrt/issues/9829 ), but turning on
spinlock debugging shows this happening in other places too.
This doesn't seem to measurably impact boot time.
Tested on bt_homehub-v5a with 5.10 and 5.15.
Signed-off-by: Thomas Nixon <tom@tomn.co.uk>
[Add commit description into patch]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
It appears that the refactor of the upgrade process for NAND devices
resulted in the nand_do_upgrade_success step not being called for
devices using the linksys.sh script. As a result, configuration
was not preserved over sysupgrade steps.
This restores the preservation of configs for ipq806x devices using the
linksys.sh script. Other devices and targets have not been examined.
This commit uses the same functionality and terminology used in commit
8634c10 ("ipq40xx: Fix Linksys upgrade, restore config step")
Fixes: e25e6d8 ("base-files: fix and clean up nand sysupgrade code")
Tested-on: EA8500
Signed-off-by: Jacob Aharon <ah.jacob@gmail.com>
PCI paths of the WLAN devices have changed between kernel 5.10 and 5.15;
migrate config so existing wifi-iface definitions don't break.
This is implemented as a hotplug handler rather than a uci-defaults script
as the migration script must run before the 10-wifi-detect hotplug handler.
based on b452af23a8
migration was forgotten when device trees were adjusted in
688697889cc77913be5bfixes#9374
affected devices:
Netgear R6220
Netgear WAC104
Netgear WNDR3700 v5
Zbtlink ZBT-WE1326
Wiflyer WF3526-P
Arcadyan WE420223-99
Beeline Smartbox Flash (Arcadyan WG443223)
MTS WG430223 (Arcadyan WG430223)
Tested-by: Maximilian Baumgartner <aufhaxer@googlemail.com>
Tested-by: Mikhail Zhilkin <csharper2005@gmail.com>
Signed-off-by: Felix Baumann <felix.bau@gmx.de>
Hanyang Digitech Co., Ltd.
MSIP-CMM-HYD-HYC-G920
CJ-Hello HYC-G920
SoC : MediaTek MT7621AT
RAM : 256M (SK hynix H5TQ2G63FFR)
FLASH : 16MB (Winbond W25Q128BV)
WiFi : MediaTek MT7602EN bgn 2SS
WiFi : MediaTek MT7612EN nac 2SS
BTN : Reset
LED : - Power RED
- WAN Green
- LAN {1-4}
- WiFi 2.4 GHz Blue
- WiFi 5 GHz Blue
- USB Green
**For MT7621 stage1 DDR Test**
UART : J4 GND - 3V3 - TX - RX - GND / 57600-8N1
```
MT7621 stage1 code 10:33:55 (ASIC)
CPU=500000000 HZ BUS=166666666 HZ
```
**For u boot environment**
UART : J4 GND - 3V3 - TX - RX - GND / 115200-8N1
**UART Menu**
```
Please choose the operation:
1: Load system code to SDRAM via TFTP.
2: Load system code then write to Flash via TFTP.
3: Boot system code via Flash (default).
4: Entr boot command line interface.
7: Load Boot Loader code then write to Flash via Serial.
9: Load Boot Loader code then write to Flash via TFTP.
```
**Steps**
Press 4: Entr boot command line interface.
On the pormpt enter.
`setenv firmware_size 0xf60000`
Then enter.
`saveenv`
Then enter.
`reset`
**Device will reboot**
Set your IP 192.168.100.100/24
Connect your lan cable to wan port.
**On the UART Menu**
Press 2: Load system code then write to Flash via TFTP.
Warning!! Erase Linux in Flash then burn new one. Are you sure?(Y/N) **enter** `Y`
Please Input new ones /or Ctrl-C to discard
Input device IP (192.168.100.55) ==:`192.168.100.55`
Input server IP (192.168.100.100) ==:`192.168.100.100`
Input Linux Kernel filename () ==:`openwrt-22.03.0-ramips-mt7621-hanyang_hyc-g920-squashfs-sysupgrade.bin`
After uploading firmware image, device will boot Openwrt.
Signed-off-by: Muhammad AL-Qadhy <m.ismael@gmail.com>
