This is an RTL8382-based switch with 24 copper ports + 4 SFP ports
Specifications:
---------------
* SoC: Realtek RTL8382M
* Flash: 32 MiB SPI flash
* RAM: 256 MiB
* Ethernet: 24x 10/100/1000 Mbps
* Buttons: 1x "Reset" button
* UART: 1x serial header, unpopulated
* SFP: 4 SFP ports
Works:
------
- (24) RJ-45 ethernet ports
- Switch functions
- Buttons
- Sys LED on front panel (no port LEDs)
Not yet enabled:
----------------
- Port LEDs (no driver for RTL8231 in this mode)
- SFP cages (no driver for PHY)
Install via web interface:
-------------------------
Not supported at this time.
Install via serial console/tftp:
--------------------------------
The U-Boot firmware drops to a TP-Link specific "BOOTUTIL" shell at
38400 baud. There is no known way to exit out of this shell, and no
way to do anything useful.
Ideally, one would trick the bootloader into flashing the sysupgrade
image first. However, if the image exceeds 6MiB in size, it will not
work. To install OpenWRT:
Prepare a tftp server with:
1. server address: 192.168.0.146
2. the image as: "uImage.img"
Power on device, and stop boot by pressing any key.
Once the shell is active:
1. Ground out the CLK (pin 16) of the ROM (U6)
2. Select option "3. Start"
3. Bootloader notes that "The kernel has been damaged!"
4. Release CLK as soon as bootloader thinks image is corrupted.
5. Bootloader enters automatic recovery -- details printed on console
6. Watch as the bootloader flashes and boots OpenWRT.
Blind install via tftp:
-----------------------
This method works when it's not feasible to install a serial header.
Prepare a tftp server with:
1. server address: 192.168.0.146
2. the image as: "uImage.img"
3. Watch network traffic (tcpdump or wireshark works)
4. Power on the device.
5. Wait 1-2 seconds then ground out the CLK (pin 16) of the ROM (U6)
6. When 192.168.0.30 makes tftp requests, release pin 16
7. Wait 2-3 minutes for device to auto-flash and boot OpenWRT
Signed-off-by: Andreas Böhler <dev@aboehler.at>
Hardware information:
---------------------
- RTL8380 SoC
- 8 Gigabit RJ45 PoE ports (built-in RTL8218B)
- 2 SFP ports (built-in SerDes)
- RJ45 RS232 port on front panel
- 32 MiB NOR Flash
- 128 MiB DDR3 DRAM
- PT7A7514 watchdog
- PoE chip
- Fanless
Known issues:
---------------------
- PoE LEDs are uncontrolled.
(Manual taken from f2f09bc)
Booting initramfs image:
------------------------
- Prepare a FTP or TFTP server serving the OpenWrt initramfs image and
connect the server to a switch port.
- Connect to the console port of the device and enter the extended
boot menu by typing Ctrl+B when prompted.
- Choose the menu option "<3> Enter Ethernet SubMenu".
- Set network parameters via the option "<5> Modify Ethernet Parameter".
Enter the FTP/TFTP filename as "Load File Name" ("Target File Name"
can be left blank, it is not required for booting from RAM). Note that
the configuration is saved on flash, so it only needs to be done once.
- Select "<1> Download Application Program To SDRAM And Run".
Initial installation:
---------------------
- Boot an initramfs image as described above, then use sysupgrade to
install OpenWrt permanently. After initial installation, the
bootloader needs to be configured to load the correct image file
- Enter the extended boot menu again and choose "<4> File Control",
then select "<2> Set Application File type".
- Enter the number of the file "openwrt-kernel.bin" (should be 1), and
use the option "<1> +Main" to select it as boot image.
- Choose "<0> Exit To Main Menu" and then "<1> Boot System".
NOTE: The bootloader on these devices can only boot from the VFS
filesystem which normally spans most of the flash. With OpenWrt, only
the first part of the firmware partition contains a valid filesystem,
the rest is used for rootfs. As the bootloader does not know about this,
you must not do any file operations in the bootloader, as this may
corrupt the OpenWrt installation (selecting the boot image is an
exception, as it only stores a flag in the bootloader data, but doesn't
write to the filesystem).
Example PoE config file (/etc/config/poe):
---------------------
config global
option budget '65'
config port
option enable '1'
option id '1'
option name 'lan8'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '2'
option name 'lan7'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '3'
option name 'lan6'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '4'
option name 'lan5'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '5'
option name 'lan4'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '6'
option name 'lan3'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '7'
option name 'lan2'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '8'
option name 'lan1'
option poe_plus '1'
option priority '2'
Signed-off-by: Kevin Jilissen <info@kevinjilissen.nl>
There are two hardware models of the HPE 1920-8g-poe switch. The version
currently in the repository is the model with a PoE budget of 180W. In
preparation of the addition of the 65W model, the existing model is
renamed to clarify the hardware version it targets.
As suggested by Pawel, the 'SUPPORTED_DEVICES' includes the old target
name to enable an upgrade path of builds with the old name.
Suggested-by: Pawel Dembicki <paweldembicki@gmail.com>
Signed-off-by: Kevin Jilissen <info@kevinjilissen.nl>
Fix Spanning Tree Protocol (STP) by changing COPY2CPU which currently
makes switch to ignore Bridge Protocol Data Units (BPDUs).
Tested on Zyxel GS1900-8, 24 and 48.
Signed-off-by: Rudolf Vesely <i@rudolfvesely.com>
[ improve commit description and add new line in different sections ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
The USXGMII implementation of Realtek switches can not only support
10GbE but also 2.5Gb and 5Gb on top of the usual data rates.
Mark those as supported to allow them to be negotiated.
This change has been tested on a ZyXEL XGS1250-12 with the following link
partners:
- NWA50AX Pro (2.5Gb)
- RTL8152 USB NIC (2.5Gb)
- AQC111 USB NIC (2.5Gb & 5Gb)
Gbit and 10GbE has also been tested to still work fine with a variety of
devices.
Signed-off-by: Tobias Schramm <tobias@t-sys.eu>
This condition was introduced in commit 51c8f76612 ("realtek: Improve
MAC config handling for all SoCs") to correctly report the speed of the
internal serdes ports as 10G, but instead makes all ports read 10G
because the or-operator should have been an and-operator.
Fixes: #9953
Fixes: 51c8f76612 ("realtek: Improve MAC config handling for all SoCs")
Signed-off-by: Peter Körner <git@mazdermind.de>
[ wrap comment to 72 column and improve commit ref ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Import commits from upstream Linux replacing some downstream patches.
Move accepted patches from pending-{5.15,6.1} to backport-{5.15,6.1}.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Hardware information:
---------------------
- RTL8380 SoC
- 8 Gigabit RJ45 PoE ports (built-in RTL8218B)
- 2 SFP ports (built-in SerDes)
- RJ45 RS232 port on front panel
- 32 MiB NOR Flash
- 128 MiB DDR3 DRAM
- PT7A7514 watchdog
- PoE chips: Nuvoton M0516LDE + BCM59121
Known issues:
---------------------
- PoE LEDs are uncontrolled.
(Manual taken from f2f09bc002)
Booting initramfs image:
------------------------
- Prepare a FTP or TFTP server serving the OpenWrt initramfs image and
connect the server to a switch port.
- Connect to the console port of the device and enter the extended
boot menu by typing Ctrl+B when prompted.
- Choose the menu option "<3> Enter Ethernet SubMenu".
- Set network parameters via the option "<5> Modify Ethernet Parameter".
Enter the FTP/TFTP filename as "Load File Name" ("Target File Name"
can be left blank, it is not required for booting from RAM). Note that
the configuration is saved on flash, so it only needs to be done once.
- Select "<1> Download Application Program To SDRAM And Run".
Initial installation:
---------------------
- Boot an initramfs image as described above, then use sysupgrade to
install OpenWrt permanently. After initial installation, the
bootloader needs to be configured to load the correct image file
- Enter the extended boot menu again and choose "<4> File Control",
then select "<2> Set Application File type".
- Enter the number of the file "openwrt-kernel.bin" (should be 1), and
use the option "<1> +Main" to select it as boot image.
- Choose "<0> Exit To Main Menu" and then "<1> Boot System".
NOTE: The bootloader on these devices can only boot from the VFS
filesystem which normally spans most of the flash. With OpenWrt, only
the first part of the firmware partition contains a valid filesystem,
the rest is used for rootfs. As the bootloader does not know about this,
you must not do any file operations in the bootloader, as this may
corrupt the OpenWrt installation (selecting the boot image is an
exception, as it only stores a flag in the bootloader data, but doesn't
write to the filesystem).
Example PoE config file (/etc/config/poe):
---------------------
config global
option budget '180'
config port
option enable '1'
option id '1'
option name 'lan8'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '2'
option name 'lan7'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '3'
option name 'lan6'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '4'
option name 'lan5'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '5'
option name 'lan4'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '6'
option name 'lan3'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '7'
option name 'lan2'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '8'
option name 'lan1'
option poe_plus '1'
option priority '2'
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
To improve code readability in drivers/net/phy/rtl83xx-phy.c, replace
constants MMD_AN and MMD_VEND2 from drivers/net/phy/rtl83xx-phy.h with
MDIO_MMD_AN and MDIO_MMD_VEND2 from <linux/mdio.h>.
Also, replace
BIT(0) with MDIO_EEE_2_5GT,
BIT(1) with MDIO_EEE_100TX,
BIT(2) with MDIO_EEE_1000T,
BIT(9) with MDIO_AN_CTRL1_RESTART,
BIT(12) with MDIO_AN_CTRL1_ENABLE,
32 with MDIO_AN_10GBT_CTRL,
60 with MDIO_AN_EEE_ADV, and
62 with MDIO_AN_EEE_ADV2
from <linux/mdio.h>.
Suggested-by: DENG Qingfang <dqfext@gmail.com>
Signed-off-by: Pascal Ernster <git@hardfalcon.net>
Replace BIT(x) and numerical values in drivers/net/phy/rtl83xx-phy.c
with constants from <linux/mii.h> to improve code readability.
To make reviewing easier, this commit only addresses ADVERTISE_* and
MII_PHYSID* constants.
Signed-off-by: Pascal Ernster <git@hardfalcon.net>
Replace numerical values, BIT(x) and (1 << x) in
drivers/net/phy/rtl83xx-phy.c with constants from <linux/mii.h> to
improve code readability.
To make reviewing easier, this commit only addresses MII_BMCR and BMCR_*
constants.
Suggested-by: DENG Qingfang <dqfext@gmail.com>
Signed-off-by: Pascal Ernster <git@hardfalcon.net>
Backport initial LEDs hw control support. Currently this is limited to
only rx/tx and link events for the netdev trigger but the API got
accepted and the additional modes are working on and will be backported
later.
Refresh every patch and add the additional config flag for QCA8K new
LEDs support.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
One is never to write to dev->addr directly. In 6.1 it will be a const and
with the newly enabled WERROR, we get a failing grade.
Lets fix this ahead of time.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
We are missing a bunch of headers, which trigger errors on 6.1, probably
due to changed header-in-header dependencies. Best add them now.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Backport commits adding support for the MT7988 built-in switch to the
mt7530 driver.
This change results in the Kconfig symbol NET_DSA_MT7530 to be extended
by NET_DSA_MT7530_MDIO (everything formally covered by NET_DSA_MT7530)
and NET_DSA_MT7530_MMIO (a new driver for the MMIO-connected built-in
switch of the MT7988 SoC).
Select NET_DSA_MT7530_MDIO for all targets previously selecting
NET_DSA_MT7530, with the exception of mediatek/filogic which also
selects NET_DSA_MT7530_MMIO.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
All targets are bumped to 5.15. Remove the old 5.10 patches, configs
and files using:
find target/linux -iname '*-5.10' -exec rm -r {} \;
Further, remove the 5.10 include.
Signed-off-by: Nick Hainke <vincent@systemli.org>
Replace fallthrough comment with fallthrough macro for rtl838x ethernet
driver.
Fix compilarion warning:
drivers/net/ethernet/rtl838x_eth.c: In function 'rtl930x_mdio_reset':
drivers/net/ethernet/rtl838x_eth.c:1959:43: error: this statement may fall through [-Werror=implicit-fallthrough=]
1959 | private_poll_mask |= BIT(i);
drivers/net/ethernet/rtl838x_eth.c:1961:17: note: here
1961 | case PHY_INTERFACE_MODE_USXGMII:
| ^~~~
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Fix uninizialized variable in rtl83xx qos driver
Fix compilation error:
drivers/net/dsa/rtl83xx/qos.c: In function 'rtl838x_setup_prio2queue_matrix':
drivers/net/dsa/rtl83xx/qos.c:298:19: error: 'v' is used uninitialized [-Werror=uninitialized]
298 | v |= i << (min_queues[i] * 3);
| ~~^~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/dsa/rtl83xx/qos.c:294:13: note: 'v' was declared here
294 | u32 v;
| ^
drivers/net/dsa/rtl83xx/qos.c: In function 'rtl83xx_setup_prio2queue_cpu_matrix':
drivers/net/dsa/rtl83xx/qos.c:320:19: error: 'v' is used uninitialized [-Werror=uninitialized]
320 | v |= max_queues[i] << (i * 3);
| ~~^~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/dsa/rtl83xx/qos.c:316:13: note: 'v' was declared here
316 | u32 v;
| ^
cc1: all warnings being treated as errors
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Comment unused part of realtek phy driver.
Fix compilation warning:
drivers/net/phy/rtl83xx-phy.c: In function 'rtl8380_configure_int_rtl8218b':
drivers/net/phy/rtl83xx-phy.c:747:21: error: unused variable 'ipd_flag' [-Werror=unused-variable]
747 | int ipd_flag = 1;
| ^~~~~~~~
drivers/net/phy/rtl83xx-phy.c: At top level:
drivers/net/phy/rtl83xx-phy.c:3333:13: error: 'rtl931x_sds_disable' defined but not used [-Werror=unused-function]
3333 | static void rtl931x_sds_disable(u32 sds)
| ^~~~~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
Comment unused part of realtek dsa driver.
Fix compilation warning:
drivers/net/dsa/rtl83xx/common.c: In function 'rtl83xx_fib_event':
drivers/net/dsa/rtl83xx/common.c:1430:58: error: unused variable 'fen6_info' [-Werror=unused-variable]
1430 | struct fib6_entry_notifier_info *fen6_info = ptr;
| ^~~~~~~~~
drivers/net/dsa/rtl83xx/common.c: At top level:
drivers/net/dsa/rtl83xx/common.c:531:12: error: 'rtl83xx_octet_cntr_alloc' defined but not used [-Werror=unused-function]
531 | static int rtl83xx_octet_cntr_alloc(struct rtl838x_switch_priv *priv)
| ^~~~~~~~~~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
Drop unused priv in realtek dsa driver.
Fix compilation warning:
drivers/net/dsa/rtl83xx/dsa.c: In function 'rtl83xx_port_lag_change':
drivers/net/dsa/rtl83xx/dsa.c:2016:37: error: unused variable 'priv' [-Werror=unused-variable]
2016 | struct rtl838x_switch_priv *priv = ds->priv;
| ^~~~
cc1: all warnings being treated as errors
Comment rtl838x_pie_rule_dump in realtek dsa driver for rtl83xx
Fix compilation warning:
drivers/net/dsa/rtl83xx/rtl838x.c:1294:13: error: 'rtl838x_pie_rule_dump' defined but not used [-Werror=unused-function]
1294 | static void rtl838x_pie_rule_dump(struct pie_rule *pr)
| ^~~~~~~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
Comment multiple function in realtek dsa driver for rtl930x
Fix compilation warning:
drivers/net/dsa/rtl83xx/rtl930x.c:1463:12: error: 'rtl930x_l3_intf_add' defined but not used [-Werror=unused-function]
1463 | static int rtl930x_l3_intf_add(struct rtl838x_switch_priv *priv, struct rtl838x_l3_intf *intf)
| ^~~~~~~~~~~~~~~~~~~
drivers/net/dsa/rtl83xx/rtl930x.c:1414:12: error: 'rtl930x_l3_mtu_del' defined but not used [-Werror=unused-function]
1414 | static int rtl930x_l3_mtu_del(struct rtl838x_switch_priv *priv, int mtu)
| ^~~~~~~~~~~~~~~~~~
drivers/net/dsa/rtl83xx/rtl930x.c:995:12: error: 'rtl930x_l3_hash6' defined but not used [-Werror=unused-function]
995 | static u32 rtl930x_l3_hash6(struct in6_addr *ip6, int algorithm, bool move_dip)
| ^~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
drivers/net/dsa/rtl83xx/rtl930x.c:1690:13: error: 'rtl930x_read_pie_fixed_fields' defined but not used [-Werror=unused-function]
1690 | static void rtl930x_read_pie_fixed_fields(u32 r[], struct pie_rule *pr)
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/dsa/rtl83xx/rtl930x.c:1432:12: error: 'rtl930x_l3_mtu_add' defined but not used [-Werror=unused-function]
1432 | static int rtl930x_l3_mtu_add(struct rtl838x_switch_priv *priv, int mtu)
| ^~~~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
Comment rtl931x_read_pie_fixed_fields in realtek dsa driver for rtl931x
Fix compilation warning:
drivers/net/dsa/rtl83xx/rtl931x.c:1116:13: error: 'rtl931x_read_pie_fixed_fields' defined but not used [-Werror=unused-function]
1116 | static void rtl931x_read_pie_fixed_fields(u32 r[], struct pie_rule *pr)
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
Comment rtl93xx_header_vlan_set in realtek ethernet driver for rtl838x
Fix compilation warning:
drivers/net/ethernet/rtl838x_eth.c: At top level:
drivers/net/ethernet/rtl838x_eth.c:164:13: error: 'rtl93xx_header_vlan_set' defined but not used [-Werror=unused-function]
164 | static void rtl93xx_header_vlan_set(struct p_hdr *h, int vlan)
| ^~~~~~~~~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Rework exposing i2c_mii_valid_phy_id and i2c_mii_phy_addr in global
include.
Fix compilation warning:
In file included from drivers/net/phy/sfp.c:11:
./include/linux/mdio/mdio-i2c.h:27:21: error: 'i2c_mii_phy_addr' defined but not used [-Werror=unused-function]
27 | static unsigned int i2c_mii_phy_addr(int phy_id)
| ^~~~~~~~~~~~~~~~
./include/linux/mdio/mdio-i2c.h:22:13: error: 'i2c_mii_valid_phy_id' defined but not used [-Werror=unused-function]
22 | static bool i2c_mii_valid_phy_id(int phy_id)
| ^~~~~~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
PHY_INTERFACE_MODE_HSGMII was not handled in phylink_get_linkmodes and
phylink_parse_mode.
Fix compilation warning by adding it in the enum:
drivers/net/phy/phylink.c: In function 'phylink_get_linkmodes':
drivers/net/phy/phylink.c:360:9: error: enumeration value 'PHY_INTERFACE_MODE_HSGMII' not handled in switch [-Werror=switch]
360 | switch (interface) {
| ^~~~~~
cc1: all warnings being treated as errors
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
All callers of the rtl83xx_mc_group_* functions already do the same
check, so these aren't needed.
For rtl83xx_mc_group_alloc, this branch also incorrectly returned 0
instead of a negative value. If the branch wasn't effectively dead code
anyway, this could potentially have caused bugs, as 0 is a valid
multicast group entry index.
Fixes: cde31976e3 ("realtek: Add support for Layer 2 Multicast")
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
The current implementation only works when store and load are called for
the same port without any other calls in between. This is because the
store function only saves a single port number instead of a portmask for
each group. It also doesn't take into account that the allocation of
multicast group entries might change between store/load calls.
As a result, the multicast port mask table gets corrupted. This also
includes the reserved entry for unknown multicast, which gets corrupted
even when no other mdb entries have been added.
Remove the code for storing/loading multicast groups entirely, as the
original commit message doesn't offer a convincing reason why this would
be necessary in the first place.
Fixes: 724e4af530 ("realtek: Store and Restore MC memberships for port enable/disable")
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
There shouldn't be any reason to forward all multicast to the CPU. The
original commit message also doesn't provide a reason for this seemingly
unrelated change.
The current implementation of the delete method is also broken, as it
entirely removes any entry when the portmask contains only the CPU port,
even if it was explicitly created.
Fixes: 724e4af530 ("realtek: Store and Restore MC memberships for port enable/disable")
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
There doesn't appear to be a reason to do this, as only the last entry
is actually reserved for unknown multicast.
This also fixes two issues:
- As the increment happened after the bounds check, the value of the
actually reserved last entry could be overwritten.
- On deletion of entries, a corresponding decrement was missing,
causing the wrong entry to be marked as free.
Fixes: cde31976e3 ("realtek: Add support for Layer 2 Multicast")
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Actually use the index returned by rtl83xx_find_l2_cam_entry.
Fixes: cde31976e3 ("realtek: Add support for Layer 2 Multicast")
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
The port_vlan_add method may be called while a port is already a member
of that VLAN, so it needs to be able to handle changed flags. Fix it to
properly handle when the PVID or UNTAGGED flag was previously set, but
now no longer is.
To reduce duplication, move PVID configuration to a separate function.
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
The registers L2_PORT_STATIC_MV_ACT seem to specify the action to take
when the source address of a packet exists as a static fdb entry on
another port. By default the configured action is to drop such packets.
For standalone ports, this behaviour is undesired, as all traffic should
be forwarded to the CPU. So change the action to forward on standalone
ports.
A situation where this issue can occur is when a non-offloaded bond
interface is part of a bridge. In that case, the CPU port will have fdb
entries for devices connected to the bond interface, which are managed
by the assisted learning feature.
For now, this is only implemented for RTL838x/RTL839x, as the available
set of registers differs for the other devices.
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
All ports are disabled by default, so configure the port isolation masks
and the pm field accordingly in the setup function. When port_enable is
called for a port, the isolation masks will be set up so that traffic
can flow between the port and the CPU.
While at it, change the code to also use the traffic_set method in
rtl83xx_setup, instead of writing to the RTL838x_PORT_ISO_CTRL(i)
registers directly.
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Correctly update the isolation mask of the port being configured. The
port_bitmap variable should contain all other bridge members and needs
to be actually removed from the isolation mask instead of added to it.
Also actually remove the port being configured from the pm field of the
other ports, so that any other ports that are currently disabled will be
configured correctly when they are enabled.
Fixes: df8e6be59a ("rtl838x: add new architecture")
[fixed updating pm field of other ports]
Fixes: 2b88563ee5 ("realtek: update the tree to the latest refactored version")
[reintroduced incorrect pm field update]
Fixes: 27029277f9 ("realtek: add switch driver support for the RTL93XX based switches")
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
The switch driver actually expects every port to have a PHY handle, and
several branches in the code determine if a port is valid by checking
for a non-zero phy field.
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
The legacy (BSD) PTY support could open security problems in a system,
We do not need them in OpenWrt, deactivate this option in all targets.
Debian also deactivates this option.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Fix mis-typed DEVICE-MODEL in mk file for EnGenius EWS2910P.
Signed-off-by: Raylynn Knight <rayknight@me.com>
[ fix wrong SoB format and improve commit title/description ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Refresh patches which were no longer applying cleanly after a recently
added SFP quirk.
Fixes: 658b45ce48 ("generic: add quirk for HG MXPD-483II 2500M fiber SFP")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
APRESIA ApresiaLightGS120GT-SS (APLGS120GTSS) is a 16 + 4 ports gigabit
switch, based on RTL8382M.
Specifications:
- SoC : Realtek RTL8382M
- RAM : DDR3 256 MiB (Nanya NT5CC256M8JQ-EK)
- Flash : SPI-NOR 32 MiB (Macronix MX25L25635FMI-10G)
- Ethernet : 10/100/1000 Mbps x16 + 4
- port 1-8 : RTL8218B
- port 9-16 : RTL8382M, TP (SoC, RTL8218B)
- port 17-20 : RTL8214FC, TP/SFP (Combo)
- LEDs/Keys : 3x/1x
- UART : through-hole on PCB
- J6: 3.3V, TX, RX, GND from tri-angle marking side
- 115200n8
- Power : 100-120/200-240 VAC, 50/60 Hz
Max. 16 W, Avg 14 W (100 VAC)
- Plug : IEC 60320-C13
Flash instruction using factory image:
1. Boot ApresiaLightGS120GT-SS normally
2. Login to WebUI and open firmware page ("ファームウェア")
3. If the device is booted from image1, set active image for next
booting ("起動イメージ選択") to image2("イメージ2"), press apply
("適用") button and reboot the device to make booting from image2
4. On the WebUI, set active image to image1
5. Select the OpenWrt factory image and press update button ("更新")
6. Open reboot page ("再起動") and press reboot button ("再起動実行")
Notes:
- "ApresiaLightGS120GT-SS" is a model name and "APLGS120GTSS" is a model
number
- this device has 3x GPIO-controlled LEDs on PCB, but 1x LED
("green:unused") has no hole on the case
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
