This commit adds support for the Linksys EA6350v3 device in the ipq-wifi
target.
Without this patch, the Linksys EA6350v3 won't be hable to have fully
functional wireless interfaces. This is not permanent: the board data has
already been sent to ath10k _at_ lists _dot_ infradead _dot_ org
Signed-off-by: Ryan Pannell <ryan@osukl.com>
Signed-off-by: Oever González <notengobattery@gmail.com>
This now matches what was generated locally on my PC and the file on the
mirror server.
Fixes: 575d0240f9 ("ath10k-firmware: update board-2.bin for community firmwares")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
SOC: IPQ4018 / QCA Dakota
CPU: Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7
DRAM: 256 MiB
NOR: 32 MiB
ETH: Qualcomm Atheros QCA8072
WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2
WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2
INPUT: RESET Button
LEDS: Power, LAN, MESH, WLAN 2.4GHz, WLAN 5GHz
1. Load Ramdisk via U-Boot
To set up the flash memory environment, do the following:
a. As a preliminary step, ensure that the board console port is connected to the PC using these RS232 parameters:
* 115200bps
* 8N1
b. Confirm that the PC is connected to the board using one of the Ethernet ports. Set a static ip 192.168.99.8 for Ethernet that connects to board. The PC must have a TFTP server launched and listening on the interface to which the board is connected. At this stage power up the board and, after a few seconds, press 4 and then any key during the countdown.
U-BOOT> set serverip 192.168.99.8 && set ipaddr 192.168.99.9 && tftpboot 0x84000000 openwrt.itb && bootm
2. Load image via GUI
a. Upgrade EAP1300 to FW v3.5.3.2
In the GUI, System Manager > Firmware > Firmware Upgrade, to do upgrade.
b. Transfer to OpenWrt from EnGenius.
In Firmware Upgrade page, to upgrade yours openwrt-ipq40xx-engenius_eap1300-squashfs-sysupgrade.bin.
3. Revert to EnGenius EAP1300
To flash openwrt-ipq40xx-engenius_eap1300-squashfs-factory.bin by using sysupgrade command and "DO NOT" keep configuration.
$ sysupgrade –n openwrt-ipq40xx-engenius_eap1300-squashfs-factory.bin
Signed-off-by: Steven Lin <steven.lin@senao.com>
It is not necessary to have iucode-tool present on target system to have
functional intel-microcode package. The build time dependency is kept.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
The BDFs for all boards were upstreamed to the ath10k-firmware
repository and linux-firmware.git.
We switched to the upstream board-2.bin, hence the files can be removed
here.
Keep the ipq-wifi package in case new boards are added. It might take
some time till board-2.bins send upstream are merged.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch updates the board-2.bin for the default
IPQ4019, QCA9984 and QCA9888 ath10k-firmware-xyz-ct
and -ct-htt firmwares.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Add the most recent supported firmware file for the Intel 9000 and
9260 wireless chips. The API version 41 is not yet supported by the driver.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Kalles ath10k PR was finally merged so update linux-firmware to
include those changes.
This is needed since disabling ath10k-firmware a lot of custom BDF-s
in board-2.bin-s are not available in previously outdated linux-firmware
board-2.bin-s.
This also includes support for boards currently using ipq-wifi and other
WIP ones.
Runtime tested on 8devices Jalapeno.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Building ls-dpl package requires the dtc tool. This patch
is to support using linux dtc tool for ls-dpl package.
This avoids compile issue when host system doesn't have
the dtc tool.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
ls1012afrdm was no longer supported in NXP Layerscape SDK.
Instead a new board ls1012afrwy was introduced in LSDK.
This patch is to drop ls1012afrdm and add ls1012afrwy support.
Since only 2MB NOR flash could be used, we just put u-boot
and firmware on NOR flash, and put kernel/dtb/rootfs on SD
card.
The Layerscape FRWY-LS1012A board is an ultra-low-cost
development platform for LS1012A Series Communication
Processors built on Arm Cortex-A53. This tool refines the
FRDM-LS1012A with more features for a better hands-on experience
for IoT, edge computing, and various advanced embedded
applications. Features include easy access to processor I/O,
low-power operation, micro SD card storage, an M2 connector, a
small form factor, and expansion board options via mikroBUS Click
Module. The MicroBUS Module provides easy expansion via hundreds
of powerful modules supporting sensors, actuators, memories,
and displays.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
NOR/QSPI Flash on Layerscape board only has limited 64MB memory size.
Since some boards (ls1043ardb/ls1046ardb/ls1088ardb/ls1021atwr)
could support SD card boot, we added SD boot support for them to put
all things on SD card to meet large memory requirement.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
The NXP TWR-LS1021A module is a development system based
on the QorIQ LS1021A processor.
- This feature-rich, high-performance processor module can
be used standalone or as part of an assembled Tower System
development platform.
- Incorporating dual Arm Cortex-A7 cores running up to 1 GHz,
the TWR-LS1021A delivers an outstanding level of performance.
- The TWR-LS1021A offers HDMI, SATA3 and USB3 connectors as
well as a complete Linux software developer's package.
- The module provides a comprehensive level of security that
includes support for secure boot, Trust Architecture and
tamper detection in both standby and active power modes,
safeguarding the device from manufacture to deployment.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
This patch is to update ls-ppa to LSDK-18.06 release
and to rework ls-ppa makefile to make it more readable.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
The rcw source code had been migrated to codeaurora
for LSDK-18.06 release and the future release. The
source code had also involved ls1012ardb/ls1012afrdm/
ls1088ardb/ls2088ardb rcw, so we updated ls-rcw to
LSDK-18.06, reworked the makefile and dropped ls-rcw-bin
package in this patch. Also reworked ls-rcw patch to
adapt to the latest source code.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
The dpl-examples source code had been migrated to
codeaurora for LSDK-18.06 release and the future
release. This patch is to update this package to
LSDK-18.06.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Actually there was no change for fman-ucode in LSDK-18.06
just tagged with LSDK-18.06. This patch is to rework the
fman-ucode makefile to make it more readable, and to use
lsdk-1806 as the PKG_VERSION.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
With AVM Fritz!Box 4040 and OpenWrt 18.06 RC1 there are many kernel warnings
kern.warn kernel: [87771.917049] ath10k_ahb a000000.wifi: Invalid VHT mcs 15 peer stats
and there are disconnections when the connected clients are many, at the moment I tried with 16 clients on 2.4 GHz and 8 on 5 GHZ.
Firmware 10.4-3.5.3-00057 fixes these warnings and the problem of disconnections of some clients.
Signed-off-by: Massimo Tum <masnia@tiscali.it>
* New microcode update packages from AMD upstream:
+ New Microcodes:
sig 0x00800f12, patch id 0x08001227, 2018-02-09
+ Updated Microcodes:
sig 0x00600f12, patch id 0x0600063e, 2018-02-07
sig 0x00600f20, patch id 0x06000852, 2018-02-06
* Adds Spectre v2 (CVE-2017-5715) microcode-based mitigation support,
plus other unspecified fixes/updates.
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
This patch adds support for ZyXEL NBG6617
Hardware highlights:
SOC: IPQ4018 / QCA Dakota
CPU: Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7
DRAM: 256 MiB DDR3L-1600/1866 Nanya NT5CC128M16IP-DI @ 537 MHz
NOR: 32 MiB Macronix MX25L25635F
ETH: Qualcomm Atheros QCA8075 Gigabit Switch (4 x LAN, 1 x WAN)
USB: 1 x 3.0 (via Synopsys DesignWare DWC3 controller in the SoC)
WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2
WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2
INPUT: RESET Button, WIFI/Rfkill Togglebutton, WPS Button
LEDS: Power, WAN, LAN 1-4, WLAN 2.4GHz, WLAN 5GHz, USB, WPS
Serial:
WARNING: The serial port needs a TTL/RS-232 3.3v level converter!
The Serial setting is 115200-8-N-1. The 1x4 .1" header comes
pre-soldered. Pinout:
1. 3v3 (Label printed on the PCB), 2. RX, 3. GND, 4. TX
first install / debricking / restore stock:
0. Have a PC running a tftp-server @ 192.168.1.99/24
1. connect the PC to any LAN-Ports
2. put the openwrt...-factory.bin (or V1.00(ABCT.X).bin for stock) file
into the tftp-server root directory and rename it to just "ras.bin".
3. power-cycle the router and hold down the the WPS button (for 30sek)
4. Wait (for a long time - the serial console provides some progress
reports. The u-boot says it best: "Please be patient".
5. Once the power LED starts to flashes slowly and the USB + WPS LEDs
flashes fast at the same time. You have to reboot the device and
it should then come right up.
Installation via Web-UI:
0. Connect a PC to the powered-on router. It will assign your PC a
IP-address via DHCP
1. Access the Web-UI at 192.168.1.1 (Default Passwort: 1234)
2. Go to the "Expert Mode"
3. Under "Maintenance", select "Firmware-Upgrade"
4. Upload the OpenWRT factory image
5. Wait for the Device to finish.
It will reboot into OpenWRT without any additional actions needed.
To open the ZyXEL NBG6617:
0. remove the four rubber feet glued on the backside
1. remove the four philips screws and pry open the top cover
(by applying force between the plastic top housing from the
backside/lan-port side)
Access the real u-boot shell:
ZyXEL uses a proprietary loader/shell on top of u-boot: "ZyXEL zloader v2.02"
When the device is starting up, the user can enter the the loader shell
by simply pressing a key within the 3 seconds once the following string
appears on the serial console:
| Hit any key to stop autoboot: 3
The user is then dropped to a locked shell.
|NBG6617> HELP
|ATEN x[,y] set BootExtension Debug Flag (y=password)
|ATSE x show the seed of password generator
|ATSH dump manufacturer related data in ROM
|ATRT [x,y,z,u] RAM read/write test (x=level, y=start addr, z=end addr, u=iterations)
|ATGO boot up whole system
|ATUR x upgrade RAS image (filename)
|NBG6617>
In order to escape/unlock a password challenge has to be passed.
Note: the value is dynamic! you have to calculate your own!
First use ATSE $MODELNAME (MODELNAME is the hostname in u-boot env)
to get the challange value/seed.
|NBG6617> ATSE NBG6617
|012345678901
This seed/value can be converted to the password with the help of this
bash script (Thanks to http://www.adslayuda.com/Zyxel650-9.html authors):
- tool.sh -
ror32() {
echo $(( ($1 >> $2) | (($1 << (32 - $2) & (2**32-1)) ) ))
}
v="0x$1"
a="0x${v:2:6}"
b=$(( $a + 0x10F0A563))
c=$(( 0x${v:12:14} & 7 ))
p=$(( $(ror32 $b $c) ^ $a ))
printf "ATEN 1,%X\n" $p
- end of tool.sh -
|# bash ./tool.sh 012345678901
|
|ATEN 1,879C711
copy and paste the result into the shell to unlock zloader.
|NBG6617> ATEN 1,0046B0017430
If the entered code was correct the shell will change to
use the ATGU command to enter the real u-boot shell.
|NBG6617> ATGU
|NBG6617#
Co-authored-by: David Bauer <mail@david-bauer.net>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: David Bauer <mail@david-bauer.net>
Specifications:
SOC: Qualcomm IPQ4018 (DAKOTA) ARM Quad-Core
RAM: 128 MB Nanya NT5CC64M16GP-DI
FLASH: 16 MiB Macronix MX25L12845EMI-12G
ETH: Qualcomm QCA8072
WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11b/g/n 2x2
WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11n/ac W2 2x2
INPUT: WPS, Mode-toggle-switch
LED: Power, WLAN 2.4GHz, WLAN 5GHz, LAN, WPS
(LAN not controllable by software)
(WLAN each green / red)
SERIAL: Header next to eth-phy.
VCC, TX, GND, RX (Square hole is VCC)
The Serial setting is 115200-8-N-1.
Tested and working:
- Ethernet (Correct MAC-address)
- 2.4 GHz WiFi (Correct MAC-address)
- 5 GHz WiFi (Correct MAC-address)
- Factory installation from tftp
- OpenWRT sysupgrade
- LEDs
- WPS Button
Not Working:
- Mode-toggle-switch
Install via TFTP:
Connect to the devices serial. Hit Enter-Key in bootloader to stop
autobooting. Command `tftpboot` will pull an initramfs image named
`C0A86302.img` from a tftp server at `192.168.99.08/24`.
After successfull transfer, boot the image with `bootm`.
To persistently write the firmware, flash an openwrt sysupgrade image
from inside the initramfs, for example transfer
via `scp <sysupgrade> root@192.168.1.1:/tmp` and flash on the device
with `sysupgrade -n /tmp/<sysupgrade>`.
append-cmdline patch taken from chunkeeys work on the NBG6617.
Signed-off-by: Magnus Frühling <skorpy@frankfurt.ccc.de>
Co-authored-by: David Bauer <mail@david-bauer.net>
Co-authored-by: Christian Lamparter <chunkeey@googlemail.com>
Ship EEPROM blobs for specific supported board only and don't have them
lurking around in our source tree but rather download them from
@github/RPi-Distro/firmware-nonfree upstream.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Currently when installing the firmware, a bunch of files and directories
that the ath10k driver does not look for are created.
The package now installs firmware for both hw 2.1 and 3.0 devices.
2.1 is abandonware but may be useful to keep.
3.0 firmware was tested on a Killer 1535 to be relatively stable with
802.11w disabled. 802.11w causes multiple firmware crashes but that's true
of other ath10k firmwares as well.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
This now matches what was generated locally on my PC and the file on the
mirror server.
Fixes: 349fe46103 ("ath10k-firmware: Update QCA988X firmware to the latest version")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add needed firmware for newer QCA Rome Bluetooth family.
This enables use of bluetooth with ath3k driver on QCA9377/9378 devices.
Signed-off-by: Robert Marko <robimarko@gmail.com>
This patch updates the QCA988X firmware to the latest revision
firmware-5.bin_10.2.4-1.0-00037
found in the ath10k-firmware and linux-firmware repositories.
Tested on TP-Link Archer C7 v2 (ar71xx).
Signed-off-by: Timo Sigurdsson <public_timo.s@silentcreek.de>
The BDFs for all boards were upstreamed to the ath10k-firmware
repository and are now part of ath10k-firmware 2018-04-19.
We switched to the upstream board-2.bin, hence the files can be removed
here.
Keep the ipq-wifi package in case new boards are added. It might take
some time till board-2.bins send upstream are merged.
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
