This adds support for offloading TC flower by using the Packet Inspection Engine
of the RTL-SoCs. Basic infrastructure support is provide with callbacks to the
tc subsystem and support for HW packet counters.
Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
All RTL SoCs addresss PHYs via their port number, which is mapped to an
SMI address. Add support for configuring this mapping via the .dts on all
SoCs apart from the 839x, where the mapping to the 64 ports is fixed.
Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
On RTL83xx enable learning of the MAC source address of the CPU port
from outgoing packets. Add documentation on bit fields. On RTL93xx
enable port-mask usage and the use of internal priority, these
SoCs automatically learn the MAC.
Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
Remove the storm control and attack warnings from the IRQ handler
of the Ethernet driver. There was no consequence to the detection
and the kernel can also handle at least the attacks itself.
Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
This enlarges the size of the TX ring buffer, which prevents warnings
when the buffer runs out of space.
Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
This fixes:
ERROR: "switch_generic_set_link" [drivers/net/phy/b53/b53_common.ko] undefined!
At some point all packages for swconfig drivers were dropped and targets
were meant to have them built into kernels. It seems b53 (re-)gained its
kmod-switch-bcm53xx however and b53 needs to be built as module.
Fixes: b2cfed48f6 ("Revert "swconfig: fix Broadcom b53 support"")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Add Vladimir Oltean's "net: dsa: don't set skb->offload_fwd_mark when
not offloading the bridge"
This covers cases where packets received by an upstream switch must be
forwarded back on the same port, which skb->offload_fwd_mark normally
prevents.
Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
This reverts commit 8f9cd1af0f.
That commit was meant to add a single EXPORT_SYMBOL_GPL() but it
actually also added few .of_match_table-s. One commit should handle one
thing and should not introduce unrelated changes.
Regarding actual changes:
1. EXPORT_SYMBOL_GPL is not required as we don't build swconfig drivers
as modules.
2. PHY drivers must not have .of_match_table. That is allowed for MDIO
drivers. This could work for some time (although is didn't for me on
bcm53xx) but does not with kernel 5.10. It causes a soft lockup and
upstream developers confirmed it's an unsupported design.
Link: https://lore.kernel.org/netdev/2b1dc053-8c9a-e3e4-b450-eecdfca3fe16@gmail.com/t/#mf80e472f35ee23f7a75cbf5b1e101a17ab3a64a3
Cc: Tobias Schramm <tobleminer@gmail.com>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This has testing support for 7 months. Time to switch.
TL-WDR4900 is disabled due to kernel size limitation.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Three missing symbols were found during mpc85xx/p2020 compilation.
While at it, CONFIG_FSL_ENETC_MDIO is moved to generic config
for consistency.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
[move CONFIG_FSL_ENETC_MDIO, remove redundant definitions, adjust
commit message/title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
With the upgrade to kernel 5.10 per default the old version is no
longer required to be in tree.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
When KERNEL_PERF_EVENTS is enabled in OpenWrt, or PERF_EVENTS in the
kernel config, the RPI_AXIPERF is exposed. Add it to the subtarget
kernel configs to avoid build failures.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
When building an image for the bcm27xx target, some combinations of
config options will fail to build due the SND_SOC_AD193X_I2C and
SND_SOC_AD193X_SPI kernel config symbols being missing.
The problem only occurs on bcm27xx as the target contains a patch that
modifies the Kconfig file containing the symbols; in the vanilla kernel,
there is no string after the tristate keyword so the symbol is not
exposed.
The _I2C symbol depends on I2C, which is enabled in the kernel configs
of all bcm27xx subtargets.
The _SPI symbol depends on SPI_MASTER, which is exposed by either
kmod-mmc-spi, kmod-spi-bitbang, kmod-spi-dev, kmod-spi-bcm2835 or
kmod-spi-bcm2835-aux.
Both symbols are defined in the sound/soc/codecs directory, which is
only included when SND_SOC is enabled, so this problem doesn't occur
when kmod-sound-soc-core is not enabled. As the
kmod-sound-soc-bcm2835-i2s package disables the SND_SOC_AD193X_SPI
symbol, it also doesn't occur when kmod-sound-soc-bcm2835-i2s is
enabled.
As there are several possible config combinations that do exhibit this
problem, it is best to solve it by adding the missing symbols to the
subtarget kernel configs. By doing this we can remove them from the
kmod-sound-soc-bcm2835-i2s package.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Switch port order was reversed due to reading the internal labling
(which mismatches the one on the case).
Signed-off-by: David Bauer <mail@david-bauer.net>
The cortex53 subtarget was missing multiple config options and the other
targets just defined some options which are not needed.
Fixes: 83672f506d ("sunxi: add testing Linux 5.10")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The kernel 5.4 configuration activated SATA Port Multiplier support, add
it to kernel 5.10 too.
Fixes: 83672f506d ("sunxi: add testing Linux 5.10")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SATA_PMP option is no longer exposed when no SATA host driver is enabled
since upstream linux commit bd322af15ce9 ("ata: make SATA_PMP option
selectable only if any SATA host driver is enabled").
Commit 1bb3f593ee ("kirkwood: update config for kernel 5.10") manually
added CONFIG_SATA_PMP=y to config file, but the config will disappear for
every kernel_oldconfig refresh.
To prevent this, a small hack is added, which selects SATA_HOST
automatically when SATA_PMP is enabled. This patch can be dropped if
SATA_MV is ever re-added into kernel config file.
Tested-by: Pawel Dembicki <paweldembicki@gmail.com>
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
[Move patch to generic/hack-5.10]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
These instructions are repeated for a few devices now, let's move
them to shared definition so we do not repeat ourselves too often.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The bootloader can leave the GPIO expander in a state which doesn't have
output drivers enabled so GPIOs will properly work for input but output
operations will have no effect.
To avoid disrupting the boot in case the bootloader left direction and
data registers in an inconsistent state (e.g. pulling SoC's reset to 0)
reconfigure everything as input.
Reviewed-by: Sander Vanheule <sander@svanheule.net>
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Globalscale MOCHAbin is a Armada 7040 based development board.
Specifications:
* Armada 7040 Quad core ARMv8 Cortex A-72 @ 1.4GHz
* 2 / 4 / 8 GB of DDR4 DRAM
* 16 GB eMMC
* 4MB SPI-NOR (Bootloader)
* 1x M.2-2280 B-key socket (for SSD expansion, SATA3 only)
* 1x M.2-2250 B-key socket (for modems, USB2.0 and I2C only)
* 1x Mini-PCIe 3.0 (x1, USB2.0 and I2C)
* 1x SATA 7+15 socket (SATA3)
* 1x 16-pin (2×8) MikroBus Connector
* 1x SIM card slot (Connected to the mini-PCIe and both M.2 slots)
* 2x USB3.0 Type-A ports via SMSC USB5434B hub
* Cortex 2x5 JTAG
* microUSB port for UART (PL2303GL/PL2303SA onboard)
* 1x 10G SFP+
* 1x 1G SFP (Connected to 88E1512 PHY)
* 1x 1G RJ45 with PoE PD (Connected to 88E1512 PHY)
* 4x 1G RJ45 ports via Topaz 88E6141 switch
* RTC with battery holder (SoC provided, requires CR2032 battery)
* 1x 12V DC IN
* 1x Power switch
* 1x 12V fan header (3-pin, power only)
* 1x mini-PCIe LED header (2x0.1" pins)
* 1x M.2-2280 LED header (2x0.1" pins)
* 6x Bootstrap jumpers
* 1x Power LED (Green)
* 3x Tri-color RGB LEDs (Controllable)
* 1x Microchip ATECC608B secure element
Note that 1G SFP and 1G WAN cannot be used at the same time as they are in
parallel connected to the same PHY.
Installation:
Copy dtb from build_dir to bin/ and run tftpserver there:
$ cp ./build_dir/target-aarch64_cortex-a72_musl/linux-mvebu_cortexa72/image-armada-7040-mochabin.dtb bin/targets/mvebu/cortexa72/
$ in.tftpd -L -s bin/targets/mvebu/cortexa72/
Connect to the device UART via microUSB port and power on the device.
Power on the device and hit any key to stop the autoboot.
Set serverip (host IP) and ipaddr (any free IP address on the same subnet), e.g:
$ setenv serverip 192.168.1.10 # Host
$ setenv ipaddr 192.168.1.15 # Device
Set the ethernet device (Example for the 1G WAN):
$ setenv ethact mvpp2-2
Ping server to confirm network is working:
$ ping $serverip
Using mvpp2-2 device
host 192.168.1.15 is alive
Tftpboot the firmware:
$ tftpboot $kernel_addr_r openwrt-mvebu-cortexa72-globalscale_mochabin-initramfs-kernel.bin
$ tftpboot $fdt_addr_r image-armada-7040-mochabin.dtb
Boot the image:
$ booti $kernel_addr_r - $fdt_addr_r
Once the initramfs is booted, transfer openwrt-mvebu-cortexa72-globalscale_mochabin-squashfs-sdcard.img.gz
to /tmp dir on the device.
Gunzip and dd the image:
$ gunzip /tmp/openwrt-mvebu-cortexa72-globalscale_mochabin-squashfs-sdcard.img.gz
$ dd if=/tmp/openwrt-mvebu-cortexa72-globalscale_mochabin-squashfs-sdcard.img of=/dev/mmcblk0 && sync
Reboot the device.
Hit any key to stop the autoboot.
Reset U-boot env and set the bootcmd:
$ env default -a
$ setenv bootcmd 'load mmc 0 ${loadaddr} boot.scr && source ${loadaddr}'
Optionally I would advise to edit the console env variable to remove earlycon as that
causes the kernel to never use the driver for the serial console.
Earlycon should be used only for debugging before the kernel can configure the console
and will otherwise cause various issues with the console.
$ setenv console 'console=ttyS0,115200'
Save and reset
$ saveenv
$ reset
OpenWrt should boot from eMMC now.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
When trying to add support for another device with Micron NAND chips,
it was discovered that the default setting in the kernel source does
not work with Micron Chips, since the device trees setting is
overwritten and hard coded by the kernel xway_nand driver. This was
the original reason for this PR.
A kernel patch sets the default ECC mode to soft without overwriting
the device tree settings and the device tree for devices using it
are updated with new parameters because the old ones are deprecated
by torvalds/linux@533af69.
A patch for kernel 5.4 is provided to support the new settings
because kernel 5.4 does not support it.
Signed-off-by: Daniel Kestrel <kestrel1974@t-online.de>
This backports a fix proposed for upstream kernel to fix overwriting
the NAND ECC engine in device tree.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
All subtargets only provide files and patches for Linux 5.10 by now
so there is little use for the old Linux 5.4 stuff. Remove it.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Armvirt is a development and testing platform and should therefore use
the latest OpenWrt Kernel by default.
Tested via qemu.
Acked-by: Rosen Penev <rosenp@gmail.com>
Acked-by: Yousong Zhou <yszhou4tech@gmail.com>
Signed-off-by: Paul Spooren <mail@aparcar.org>
Malta is a development and testing platform and should therefore use the
latest OpenWrt Kernel by default.
Acked-by: Rosen Penev <rosenp@gmail.com>
Acked-by: Yousong Zhou <yszhou4tech@gmail.com>
Signed-off-by: Paul Spooren <mail@aparcar.org>
Add common features 'gpio', 'nand', 'pci', 'pcie', 'squashfs' and 'usb'
for all mediatek targets, add 'display' and 'usbgadget' for MT7623.
Sort features alphabetically while at it.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
User reported that R64 doesn't provide power to the mPCIe slot in case
the PCIe port is disabled as it is when selecting the SATA
configuration. As users may still want to use USB-connected mPCIe
modules in CN8 slot.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Netgear Nighthawk AC2100 is another name of the Netgear R6700v2.
Signed-off-by: Dale Hui <strokes-races0b@icloud.com>
[adjust commit message/title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
With the various variants of Netgear R**** devices, make it more
obvious which image should be used for the R7200.
Signed-off-by: Dale Hui <strokes-races0b@icloud.com>
[provide proper commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This patch adds "KERNEL_TESTING_PATCHVER:=5.10" to the Makefile in
realtek target to allow using Kernel 5.10 for testing.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
On the devices with PoE support, the secondary UART (uart1) on the SoC
is used to communicate between the SoC and controller.
Enable the secondary UART on the following devices:
- D-Link DGS-1210-10P
- Netgear GS110TPP v1
- Netgear GS310TP v1
- ZyXEL GS1900-8HP v1/v2
- ZyXEL GS1900-10HP
- ZyXEL GS1900-24HP v2
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
The new backported GPIO driver supports interrupt, so use gpio-keys
instead of gpio-keys-polled for keys connected to the internal GPIO
controller.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
this patch includes the following changes:
- adjust mapping for the new driver
- GPIO 24 -> GPIO 0
- GPIO 47 -> GPIO 0 (+ disabling system LED)
- disable pins in the invalid range
(out of the range 0-31 of the new driver)
- are these pins on the external RTL8231 (&gpio1)?
- GPIO 67 (-> GPIO 3 on &gpio1?)
- GPIO 94 (-> GPIO 30 on &gpio1?)
- drop "indirect-access-bus-id" property from gpio0 node in device dts
files
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
dsa_to_port function in 5.10 returns dsa_port from the port list in
dsa_switch_tree, but the tree is built when the switch is registered
by dsa_register_switch and it's null in rtl83xx_mdio_probe.
So, we need to use dsa_to_port after the registration of the switch.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
This patch adds a pinctrl-single pinmux node to allow disabling system
LED and enabling GPIO 0 (old driver: GPIO 24).
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
this patch fixes the following errors when compiling:
- dsa_switch_alloc is removed[1]
- a parameter "enum dsa_tag_protocol mprot" is added to dsa_tag_protocol
in dsa_switch_ops (include/net/dsa.h)
- several paramters are added to "phylink_mac_link_up" in dsa_switch_ops
(include/net/dsa.h)
added:
- int speed
- int duplex
- bool tx_pause
- bool rx_pause
- a parameter "struct switchdev_trans *trans" is added to
port_vlan_filtering in dsa_switch_ops (include/net/dsa.h)
[1]: https://lore.kernel.org/lkml/20191020031941.3805884-17-vivien.didelot@gmail.com/
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
this patch fixes the following errors when compiling:
- "unsigned int txqueue" is added as an additional parameter of
ndo_tx_timeout in net_device_ops (include/linux/netdevice.h)
- "mac_link_state" in phylink_mac_ops (include/linux/phylink.h)
is renamed to "mac_pcs_get_state" and changed the return value
to void from int
- several parameters are added to "mac_link_up" in phylink_mac_ops
(include/linux/phylink.h) and the order of the parameters is
changed
added:
- int speed
- int duplex
- bool tx_pause
- bool rx_pause
- a parameter "phy_interface_t *interface" is added to of_get_phy_mode
(drivers/of/of_net.c) and returns the state instead of phy mode
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
this patch updates SoC dtsi (rtl838x.dtsi, rtl930x.dtsi) for the
following backported drivers:
- gpio-realtek-otto (5.13)
- spi-realtek-rtl (5.12)
- irq-realtek-rtl (5.12)
And, disable SoC GPIO node (gpio0) in rtl930x.dtsi in dts-5.10.
Currently, the upstreamed driver doesn't support the GPIO controller on
RTL930x SoC.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
the following changes are included in this patch:
- node is enabled by default, drop 'status = "okay"'
- adjust order of "compatible" lines and "reg" lines
- add a new blank line before fixed-link node in rtl830x.dtsi
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
This patch adds "dts-5.10" directory to use backported drivers.
There are several specification changes in the new drivers, so there
are some compatibility issues in using dts/dtsi files for 5.4.
The old DTS files are moved to "dts-5.4", so their corresponding
kernel version is obvious as well.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
[change "dts" to "dts-5.4", adjust Makefile]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The following line is already defined in arch/mips/Kbuild.platforms by
300-mips-add-rtl838x-platform.patch.
platform-$(CONFIG_RTL838X) += rtl838x/
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
A macro with the same name is provided in asm/pgtable.h in Kernel 5.10,
use it and drop from ioremap.h.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
This patch backports "irq-realtek-rtl" driver to Kernel 5.10 from 5.12.
"MACH_REALTEK_RTL" is used as a platform name in upstream, but "RTL838X"
is used in OpenWrt, so update the dependency by the additional patch.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
To use backported irq driver, drop old irq driver from realtek target
and call irqchip_init() in setup.c.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
To backport the upstreamed driver (gpio-realtek-otto) from 5.13, drop the
old driver from realtek target.
And, modify 301-gpio-add-rtl838x-driver.patch to remove rtl838x GPIO
support and rename it only for rtl8231 GPIO support.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
This patch backports "spi-realtek-rtl" driver to Kernel 5.10 from 5.12.
"MACH_REALTEK_RTL" is used as a platform name in upstream, but "RTL838X"
is used in OpenWrt, so update the dependency by the additional patch.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
To backport the upstreamed driver (spi-realtek-rtl) from 5.12, drop the
old driver from realtek target.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
this patch copies the following files from 5.4 to 5.10:
- config-5.4 -> config-5.10
- files-5.4/ -> files-5.10/
- patches-5.4/ -> patches-5.10/
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
[rebase on change in files-5.4]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Expose I2C busses with a chardev device. This is required to control the
PSE controller on the Ubiquiti UniFi Flex Switch.
Signed-off-by: David Bauer <mail@david-bauer.net>
Hardware
--------
MediaTek MT7621AT
16M SPI-NOR Macronix MX25L12835FMI
Microchip PD69104B1 4-Channel PoE-PSE controller
TI TPS2373 PoE-PD controller
PoE-Controller
--------------
By default, the PoE outputs do not work with OpenWrt. To make them output
power, install the "poemgr" package from the packages feed.
This package can control the PD69104B1 PSE controller.
Installation
------------
1. Connect to the booted device at 192.168.1.20 using username/password
"ubnt" via SSH.
2. Add the uboot-envtools configuration file /etc/fw_env.config with the
following content
$ echo "/dev/mtd1 0x0 0x1000 0x10000 1" > /etc/fw_env.config
3. Update the bootloader environment.
$ fw_setenv boot_openwrt "fdt addr \$(fdtcontroladdr);
fdt rm /signature; bootubnt"
$ fw_setenv bootcmd "run boot_openwrt"
4. Transfer the OpenWrt sysupgrade image to the device using SCP.
5. Check the mtd partition number for bs / kernel0 / kernel1
$ cat /proc/mtd
6. Set the bootselect flag to boot from kernel0
$ dd if=/dev/zero bs=1 count=1 of=/dev/mtdblock4
7. Write the OpenWrt sysupgrade image to both kernel0 as well as kernel1
$ dd if=openwrt.bin of=/dev/mtdblock6
$ dd if=openwrt.bin of=/dev/mtdblock7
8. Reboot the device. It should boot into OpenWrt.
Restore to UniFi
----------------
To restore the vendor firmware, follow the Ubiquiti UniFi TFTP
recovery guide for access points. The process is the same for
the Flex switch.
Signed-off-by: David Bauer <mail@david-bauer.net>
TP-Link CPE710-v1 is an outdoor wireless CPE for 5 GHz with
one Ethernet port based on the AP152 reference board
Specifications:
- SoC: QCA9563-AL3A MIPS 74kc @ 775MHz, AHB @ 258MHz
- RAM: 128MiB DDR2 @ 650MHz
- Flash: 16MiB SPI NOR Based on the GD25Q128
- Wi-Fi 5Ghz: ath10k chip (802.11ac for up to 867Mbps on 5GHz wireless
data rate) Based on the QCA9896
- Ethernet: one 1GbE port
- 23dBi high-gain directional 2×2 MIMO antenna and a dedicated metal
reflector
- Power, LAN, WLAN5G Blue LEDs
- 3x Blue LEDs
Flashing instructions:
Flash factory image through stock firmware WEB UI or through TFTP
To get to TFTP recovery just hold reset button while powering on for
around 30-40 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP:192.168.0.100
Stock device TFTP address:192.168.0.254
Signed-off-by: Andrew Cameron <apcameron@softhome.net>
[convert to nvmem, fix MAC assignment in 11-ath10k-caldata]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This backports the upstream commit:
leds: lp55xx: Initialize enable GPIO direction to output
Without it under kernel 5.10 on Asus MAP-AC2200
the LED driver will fail probing:
[ 1.947521] lp5523x: probe of 0-0032 failed with error -22
After the backported fix:
[ 1.873236] lp5523x 0-0032: lp5523 Programmable led chip found
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Tested-by: Szabolcs Hubai <szab.hu@gmail.com> [ipq4029/gl-b1300]
Tested-by: Nick Hainke <vincent@systemli.org> [ipq4019/fritzbox-7530
ipq4019/fritzbox-4040
ipq4019/sxtsq-5ac]
Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de> [ipq4019/map-ac2200]
Add kernel 5.10 as the testing kernel to ipq40xx to
get wider testing.
The following devices failed to build with buildbot settings and all
feeds installed (apparently due to kernel size):
* cell-c rtl30vw
* compex wpj428
* devolo magic 2 next
* engenius emr3500
* glinet gl-b1300
* glinet gl-s1300
* qcom ap-dk01.1-c1
* qcom ap-dk04.1-c1
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Tested-by: Nick Hainke <vincent@systemli.org> [ipq4019/fritzbox-7530
ipq4019/fritzbox-4040
ipq4019/sxtsq-5ac]
Tested-by: Szabolcs Hubai <szab.hu@gmail.com> [ipq4029/gl-b1300]
Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de> [ipq4019/map-ac2200]
[add tested-by and note about failed devices]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
MDIO drivers were moved into their own sub directory of networking drivers.
This has caused the AR40xx driver to probe before MDIO drivers and that wont
work as it depends on the MDIO bus to be up so it can be fetched.
Lets solve it by moving the AR40xx into MDIO folder so they get probed like
before.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters.
This is a required ethtool op since kernel 5.7.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
In kernel v5.5 of_get_phy_mode had its API changed, so its now returning 0
or errors instead of phymode.
Phymode is now returning by passing a pointer to phy_interface_t where it
will be stored.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Copy config from 5.4 and run "make kernel_oldconfig".
Select default ("N") for all new symbols.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
[make commit message more explicit]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Refresh the kernel patches on top of 5.10 so they apply.
Manually fixup the 705-net-add-qualcomm-ar40xx-phy.patch
to apply.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
USB and SDHCI LDO DTS patches have been upstreamed into 5.12, so
replace the local versions with upstreamed ones.
Reorder, and clearly mark the kernel version.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
I-O DATA WN-DX2033GR is a 2.4/5 GHz band 11ac (Wi-Fi 5) router, based on
MT7621A.
Specification:
- SoC : MediaTek MT7621A
- RAM : DDR3 128 MiB
- Flash : Raw NAND 128 MiB (Macronix MX30LF1G18AC-TI)
- WLAN : 2.4/5 GHz
- 2.4 GHz : 2T2R, MediaTek MT7603E
- 5 GHz : 4T4R, MediaTek MT7615
- Ethernet : 5x 10/100/1000 Mbps
- Switch : MediaTek MT7530 (SoC)
- LEDs/Keys : 2x/3x (2x buttons, 1x slide-switch)
- UART : through-hole on PCB
- J5: 3.3V, TX, RX, NC, GND from triangle mark
- 57600n8
- Power : 12 VDC, 1 A
Flash instruction using initramfs image:
1. Boot WN-DX2033GR normally
2. Access to "http://192.168.0.1/" and open firmware update page
("ファームウェア")
3. Select the OpenWrt initramfs image and click update ("更新") button
to perform firmware update
4. On the initramfs image, download the sysupgrade.bin image to the
device and perform sysupgrade with it
5. Wait ~120 seconds to complete flashing
Notes:
- The hardware of WN-DX2033GR and WN-AX2033GR are almost the same, and
it is certified under the same radio-wave related regulations in Japan
- The last 0x80000 (512 KiB) in NAND flash is not used on stock firmware
- stock firmware requires "customized uImage header" (called as "combo
image") by MSTC (MitraStar Technology Corp.), but U-Boot doesn't
- uImage magic ( 0x0 - 0x3 ) : 0x434F4D42 ("COMB")
- header crc32 ( 0x4 - 0x7 ) : with "data length" and "data crc32"
- image name (0x20 - 0x37) : model ID and firmware versions
- data length (0x38 - 0x3b) : kernel + rootfs
- data crc32 (0x3c - 0x3f) : kernel + rootfs
- There are 2x important flags in the flash:
- bootnum : select os partition for booting (persist, 0x4)
- 0x01: firmware
- 0x02: firmware_2
- debugflag : allow interrupt kernel loader, it's named as "Z-LOADER"
(Factory, 0xFE75)
- 0x00: disable debug
- 0x01: enable debug
MAC addresses:
LAN : 50:41:B9:xx:xx:90 (Factory, 0xE000 (hex) / Ubootenv, ethaddr (text))
WAN : 50:41:B9:xx:xx:92 (Factory, 0xE006 (hex))
2.4 GHz : 50:41:B9:xx:xx:90 (Factory, 0x4 (hex))
5 GHz : 50:41:B9:xx:xx:91 (Factory, 0x8004 (hex))
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
GPIOs > 31 require special handling. This patch fixes both the
initialisation and direction get/set operations.
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-by: Sander Vanheule <sander@svanheule.net>
Add additional header information required for newer
bootloaders found on DIR-2660-A1 & A2.
Also remove the MTD splitter compatible from the second firmware
partition, as OpenWrt only supports handling of the first one.
Signed-off-by: Alan Luck <luckyhome2008@gmail.com>
[rephrase commit message, remove removal of read-only flags]
Signed-off-by: David Bauer <mail@david-bauer.net>
The rockchip platform supports squashfs SD card images. However, the
resulting image is not padded to completely fill the rootfs partition.
Because of that, the f2fs overlay might not be erased, resulting in
uci-defaults not bing executed or the configuration not being erased,
even though drop config was selected.
Modify the image generation process so the image is padded to cover the
entire root filesystem partition.
Signed-off-by: David Bauer <mail@david-bauer.net>
Remove use of DEVICE_TITLE in favor of the
DEVICE_VENDOR and DEVICE_MODEL as used by
all other targets.
Signed-off-by: Moritz Warning <moritzwarning@web.de>
Remove use of DEVICE_TITLE in favor of the
DEVICE_VENDOR and DEVICE_MODEL as used by
all other targets.
Signed-off-by: Moritz Warning <moritzwarning@web.de>
Meraki wrote the ethernet MAC-address of the device
onto the eeprom (AT24C64) at the fixed location 0x66
to 0x6C. Let's fetch it from there.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
commit 5ec60cbe9d ("scripts: mkits.sh: replace @ with - in nodes")
broke support for Meraki MR32 and this patch makes the replacement
configurable allowing for specifying the @ or - or whatever character
that is desired to retain backwards compatibility with existing devices.
For example, this patch includes the fix for the Meraki MR32 in
target/linux/bcm53xx/image for meraki_mr32:
DEVICE_DTS_DELIMITER := @
DEVICE_DTS_CONFIG := config@1
Fixes: 5ec60cbe9d ("scripts: mkits.sh: replace @ with - in nodes")
Signed-off-by: Damien Mascord <tusker@tusker.org>
[Added tags, checkpatch.pl fixes, noted that this is for old stuff]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
With GCC11, memcpy doesn't work here as it assumes a size of 0. Use
ioremap to avoid it.
Fixed parameter type to match board_get_mac_address.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
This fixes:
Distributed Switch Architecture (NET_DSA) [Y/n/m/?] y
Tag driver for Atheros AR9331 SoC with built-in switch (NET_DSA_TAG_AR9331) [N/m/y/?] n
Tag driver for Broadcom switches using in-frame headers (NET_DSA_TAG_BRCM) [N/m/y/?] n
Tag driver for Broadcom legacy switches using in-frame headers (NET_DSA_TAG_BRCM_LEGACY) [N/m/y/?] (NEW)
Error in reading or end of file.
Fixes: 8fa1b576bb ("linux: update b53 upstream driver")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
