Commit Graph

24291 Commits

Author SHA1 Message Date
Vivek Unune
209c5918b5 bcm53xx: enhance support for Linksys EA9500
1. Add leds and configs
2. Add network configs
3. Add script to clear partial boot flag
4. Hack to use port 5 as cpu port as port 8 connected to eth2
   wont pass any frames
5. Enable EA9500 image generation

Hardware Info:

- Processor - Broadcom BCM4709C0KFEBG dual-core @ 1.4 GHz
- Switch - BCM53012 in BCM4709C0KFEBG & external BCM53125
- DDR3 RAM - 256 MB
- Flash - 128 MB (Toshiba TC58BVG0S3HTA00)
- 2.4GHz - BCM4366 4×4 2.4/5G single chip 802.11ac SoC
- Power Amp - Skyworks SE2623L 2.4 GHz power amp (x4)
- 5GHz x 2 - BCM4366 4×4 2.4/5G single chip 802.11ac SoC
- Power Amp - PLX Technology PEX8603 3-lane, 3-port PCIe switch
- Ports - 8 Ports, 1 WAN Ports
- Antennas - 8 Antennas
- Serial Port - @j6 [GND,TX,RX] (VCC NC) 115200 8n1

Flashing Instructions:

1. Connect a USB-TTL table to J6 on the router as well as a
   ethernet cable to a lan port and your PC.
2. Power-on the router.
3. Use putty or a serial port program to view the terminal.
   Hit Ctrl+C and interrupt the CFE terminal terminal.
4. Setup a TFTP server on your local machine at setup you
   local IP to 192.168.1.2
5. Start the TFTP Server
6. Run following commands at the CFE terminal

   flash -noheader 192.168.1.2:/openwrt.trx nflash0.trx
   flash -noheader 192.168.1.2:/openwrt.trx nflash0.trx2
   nvram set bootpartition=0 && nvram set partialboots=0 && nvram commit

7. Reboot router to be presented by OpenWrt

Note: Only installation method via serial cable is supported at the moment.
The trx firmware has to be flashed to both the partitions using following
commands from CFE prompt. This will cover US and Non-US variants.

Signed-off-by: Vivek Unune <npcomplete13@gmail.com>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-04-01 08:58:14 +02:00
Rafał Miłecki
22369ad788 bcm53xx: use upstream Linksys EA9500 fixes
One fix was accepted, one was added.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-04-01 07:12:42 +02:00
Daniel Golle
aa0adc8e3c
kernel: fix FIT partition parser compatibility issues
The uImage.FIT partition parser used to squeeze in FIT partitions in
the range where partition editor tools (fdisk and such) expect the
regular partition. This is confusing people and tools when adding
additional partitions on top of the partition used for OpenWrt's
uImage.FIT.
Instead of squeezing in the additional partitions, rather start with
all uImage.FIT partitions at offset 64.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-03-31 22:54:12 +01:00
Rafał Miłecki
1cc5eb45d5 bcm4908: backport DT patch adding Ethernet MAC address
This tells OS (Linux) where from MAC should be read (bootloader MTD
partition).

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-03-31 23:15:49 +02:00
Daniel Golle
7043e4334f
mediatek: mt7622: improve sysupgrade on MMC
Use generic functions to acquire rootdev.
Make sure to wipe rootfs_data in case of '-n'.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-03-31 16:54:14 +01:00
Álvaro Fernández Rojas
0bc5ecf2d0 bmips: backport pinctrl fixes
Backport some minor upstream fixes for the pinctrl drivers.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2021-03-31 17:29:25 +02:00
Ilya Lipnitskiy
a86c3fd800 ramips: mt7620: ralink-i2s: fix modpost error
Fixes the following error when building without CONFIG_MODULE_STRIPPED:
  FATAL: modpost: sound/soc/ralink/snd-soc-ralink-i2s: struct
  of_device_id is not terminated with a NULL entry!

Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
2021-03-31 01:10:01 +01:00
Rui Salvaterra
070ead4d4a ramips/mt7621: enable support for cpuidle
MIPS Coherent Processor Systems (CPS), which include the MT7621 SoC, support
deep sleep idle states and have a specific cpuidle driver for them.
Enable support for it, while also switching from constant timer ticks to the
idle dynticks model, with the TEO governor.

Run-tested on a Redmi AC2100.

Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
2021-03-31 00:58:49 +01:00
Rui Salvaterra
9c3b2d7ff7 ramips/mt7621: drop the timer recalibration patch
We've been carrying this patch for many years [1], in order to fix a timer
calibration issue on MT7621. Turns out, after retesting with a recent kernel
(Linux 5.10), the system works perfectly fine without it (no rcu_sched stalls
or inconsistent BogoMIPS values across CPUs).

Manually refreshed:
322-mt7621-fix-cpu-clk-add-clkdev.patch
323-mt7621-memory-detect.patch

[1] https://git.openwrt.org/?p=openwrt/openwrt.git;a=commitdiff;h=6f4a903533361a2906a4d94ac6f597cd9c6c47bc

Suggested-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
Tested-by: Donald Hoskins <grommish@gmail.com>
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
2021-03-31 00:58:49 +01:00
Rui Salvaterra
4b2e4518ac ramips/mt7621: drop the weak reordering patch
In order to fix random hangs on MT7621, we've been selecting
WEAK_REORDERING_BEYOND_LLSC for years [1]. However, these random hangs have been
most likely caused by an oversight in the MIPS implementation of the kernel
memory consistency model, which has already been fixed for some time (and
backported to stable) [2].

Manually refreshed:
321-mt7621-timer.patch

[1] https://git.openwrt.org/?p=openwrt/openwrt.git;a=commitdiff;h=5c971cd6fdd7298a2017bdb6bea870088eddb8b9
[2] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/arch/mips?h=linux-5.4.y&id=42344113ba7a1ed7b5654cd5270af0d5698d8521

Suggested-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
Tested-by: Donald Hoskins <grommish@gmail.com>
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
2021-03-31 00:58:49 +01:00
Zoltan HERPAI
bb9915407b sunxi: enable wifi module on Pine64 boards
The Pine64(+) and the SoPine64 baseboard has an optional BT+WiFi
module, carrying an RTL8723BS. The wifi part is connected via
SDIO, the BT part is connected via UART. The BT part requires
additional code changes in the drivers so we'll skip that until 5.10.
Aside from a DTS patch to enable the wifi module, add the required
packages into the device definitions.

[    8.996970] RTL8723BS: module init start
[    9.000922] RTL8723BS: rtl8723bs v4.3.5.5_12290.20140916_BTCOEX20140507-4E40
[    9.007965] RTL8723BS: rtl8723bs BT-Coex version = BTCOEX20140507-4E40
[    9.014785] pnetdev = 000000009bdd5000
[    9.047780] RTL8723BS: rtw_ndev_init(wlan0)
[    9.053349] RTL8723BS: module init ret =0

root@OpenWrt:/# iw list
Wiphy phy0
        wiphy index: 0
        max # scan SSIDs: 9
        max scan IEs length: 2304 bytes
        max # sched scan SSIDs: 0
        max # match sets: 0
        Retry short limit: 7
        Retry long limit: 4
        Coverage class: 0 (up to 0m)
        Available Antennas: TX 0 RX 0
        Supported interface modes:
                 * IBSS
                 * managed
                 * AP
                 * monitor
        Band 1:
                Frequencies:
                        * 2412 MHz [1] (20.0 dBm)
                        * 2417 MHz [2] (20.0 dBm)
                        * 2422 MHz [3] (20.0 dBm)
                        * 2427 MHz [4] (20.0 dBm)
                        * 2432 MHz [5] (20.0 dBm)
                        * 2437 MHz [6] (20.0 dBm)
                        * 2442 MHz [7] (20.0 dBm)
                        * 2447 MHz [8] (20.0 dBm)
                        * 2452 MHz [9] (20.0 dBm)
                        * 2457 MHz [10] (20.0 dBm)
                        * 2462 MHz [11] (20.0 dBm)
                        * 2467 MHz [12] (20.0 dBm) (no IR)
                        * 2472 MHz [13] (20.0 dBm) (no IR)
                        * 2484 MHz [14] (20.0 dBm) (no IR)

Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
2021-03-29 21:44:34 +02:00
Zoltan HERPAI
78c1ed64fa sunxi: enable MUSB in A53 subtarget
The Pine64(+) and the SoPine64 baseboard has two USB ports. One of
these (the lower) is connected directly to a USB host, the other
one's (upper) PHY is shared with the separate OTG controller. In
order to get it working, MUSB support needs to be enabled.

As there are other targets which compile MUSB support into the kernel
and not package it into modules, the same is done here.

[    1.348760] usb usb5: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.04
[    1.357029] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.364250] usb usb5: Product: MUSB HDRC host driver
[    1.369219] usb usb5: Manufacturer: Linux 5.4.99 musb-hcd
[    1.374617] usb usb5: SerialNumber: musb-hdrc.1.auto
[    1.379891] hub 5-0:1.0: USB hub found
[    1.383677] hub 5-0:1.0: 1 port detected
[...]
[  697.299440] usb 1-1: new high-speed USB device number 2 using ehci-platform
[  697.461855] usb 1-1: New USB device found, idVendor=090c, idProduct=1000, bcdDevice=11.00
[  697.470038] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[  697.477180] usb 1-1: Product: USB Flash Disk

Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
2021-03-29 21:28:27 +02:00
Álvaro Fernández Rojas
bb2d6ffe61 bmips: dts: align LEDs
Align all bmips devices LED configurations.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2021-03-29 18:23:38 +02:00
Álvaro Fernández Rojas
08d8a3646b bmips: backport accepted pinctrl patches
These patches have been accepted for linux v5.13.
External interrupts not supported for now.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2021-03-29 18:23:27 +02:00
Álvaro Fernández Rojas
1b1a9d1944 bmips: vr-3032u: fix gpio keys
These GPIO keys were assigned to incorrect pins.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2021-03-29 18:23:25 +02:00
Álvaro Fernández Rojas
483cc69fef bmips: dgnd3700-v2: fix gpio keys
These GPIO keys were assigned to incorrect pins.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2021-03-29 18:23:25 +02:00
Rafał Miłecki
f8669c174e bcm53xx: fix Linksys EA9500 partitions
Use proper DT binding.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-03-29 09:29:16 +02:00
Rafał Miłecki
3fd0a4222b kernel: backport 5.13 mtd partitioning changes
1. Use upstream accepted NVMEM patches
2. Minor fix for BCM4908 partitioning
3. Support for Linksys firmware partitions on Northstar

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-03-29 08:46:17 +02:00
Sven Eckelmann
c20ac84803 mvebu: Fix mac addresses for GL.iNet GL-MV1000
The original GL.iNet firmware has two different mac addresses in the
factory/art partition. The first one is for the WAN interface only and the
second one is for both lan0 and lan1.

But the original submission for OpenWrt didn't initialize the mac
addresses of the LAN ports for the DSA device at all. The ethernet mac
address was then used for all DSA ports.

Fixes: 050c24f05c ("mvebu: add support for GL.iNet GL-MV1000")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
2021-03-27 16:56:50 +01:00
Shiji Yang
b88d2850c6 ramips: correct switch config of Youku yk1
There are only two lan ports and one wan port on Youku yk1

Fixes: e9baf8265b ("ramips: add support for Youku YK1")

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
[add Fixes:]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-03-27 16:54:15 +01:00
John Audia
55be1c3734 kernel: bump 5.4 to 5.4.108
All modifications made by by update_kernel.sh.

Build system: x86_64
Build-tested: ipq806x/R7800
Run-tested: ipq806x/R7800 [only 5.4.107]
No dmesg regressions, everything functional

Run-tested by @timocapa:
 - ramips/mt7621/{Xiaomi R3G, Redmi 2100}
 - Lantiq/XWAY/Fritz!Box 7320/7330

Signed-off-by: John Audia <graysky@archlinux.us>
[squash, edit commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-03-27 16:39:31 +01:00
INAGAKI Hiroshi
e2331fb549 ath79: fix label_mac for NEC Aterm WG1200CR
On NEC Aterm WG1200CR, the MAC address for WAN is printed in the label
on the case, not LAN.
This patch fixes this issue.

Fixes: 50fdc0374b ("ath79: provide label MAC address")

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2021-03-27 16:28:01 +01:00
Sven Eckelmann
01b911a938 mvebu: Add button support for GL.iNet GL-MV1000
The original patch to support this device advertised support for the reset
button and the "switch" in the commit message. But neither were actually
integrated in the device tree or documented anywere.

The button itself is now used to trigger a reset (as described in the
official GL.iNet documentation). The switch itself is registered as BTN_0
like other devices from GL.iNet in ath79.

Fixes: 050c24f05c ("mvebu: add support for GL.iNet GL-MV1000")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
2021-03-27 16:22:11 +01:00
Hauke Mehrtens
ebfc94aee9 kernel: Move CONFIG_USERIO to generic config
The CONFIG_USERIO option is unset in multiple target configurations. On
the sunxi target it is activated. Move the kernel configuration option
to the generic kernel configuration.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2021-03-27 14:34:22 +01:00
Hauke Mehrtens
7d6553c72e kernel: Deactivate CONFIG_VFIO in generic kernel config
Instead of deactivating this in every target config, deactivate it once
in the generic kernel config. I was asked for this config option in a
x86 64 build in OpenWrt 21.02.

Fixes: 87046e87e2 ("kernel: add missing kernel config symbol")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2021-03-27 14:34:00 +01:00
Kevin Darbyshire-Bryant
87046e87e2 kernel: add missing kernel config symbol
Bump to 5.10.26 reversed dependencies on IOMMU for CONFIG_VFIO thus
malta (at least) prompted for this new symbol.

Set it to 'false' in the default config.  rockchip & X86 enable it in
target specific configs.

Thanks to Tony Ambardar for falling over this one

Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
2021-03-27 09:09:57 +00:00
Stan Grishin
64eaf633ff x86/base-files: add support for Sophos SG/XG-105
This adds detection of the Sophos SG-105 and Sophos XG-105 models
and assignment of ethernet ports these models have to LAN/WAN.

Signed-off-by: Stan Grishin <stangri@melmac.net>
2021-03-26 09:15:38 -10:00
Rui Salvaterra
27344b3784 kernel: bump 5.10 to 5.10.26
Automatically refreshed:
ath79/patches-5.10/471-mtd-cfi_cmdset_0002-AMD-chip-0x2201-write-words.patch
bcm63xx/patches-5.10/143-gpio-fix-device-tree-gpio-hogs-on-dual-role-gpio-pin.patch
generic/hack-5.10/204-module_strip.patch

Run-tested:
ath79 (TL-WDR3600)
x86_64 (APU2 - ldir)

Tested-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
2021-03-26 08:19:11 +00:00
Rafał Miłecki
6dd727ac24 kernel: create bootfs partition when parsing on BCM4908
It's helpful for accessing booting data (DTS, kernel, etc.). It has to
be used carefully as CFE's JFFS2 support is quite dumb. It doesn't
recognize deleted files and has problems handling 0 inode.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-03-24 18:22:37 +01:00
Daniel Golle
6f5cd3bdcf
mediatek: generate complete sdcard image for BPi-R64
Populate the recovery and production partitions of the generated sdcard
image for the Bananapi BPi-R64.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-03-24 15:27:54 +00:00
Álvaro Fernández Rojas
5053593e66 bmips: reorganize patches
Reorder kernel patches after recent backports.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2021-03-24 14:49:46 +01:00
Álvaro Fernández Rojas
4165e565d2 bmips: switch to upstream ehci overcurrent flag
After backporting upstream ehci overcurrent patches we need to use spurious-oc
instead of ignore-oc.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2021-03-24 14:19:12 +01:00
Álvaro Fernández Rojas
bd47189602 kernel: backport ehci overcurrent patches
These patches have been accepted for v5.13.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2021-03-24 14:05:38 +01:00
Kevin Darbyshire-Bryant
22d2c972c4 kernel: drop apu2 reboot patch
This patch really annoys me, either it needs to go upstream or be
dropped, so it's going to be dropped here.

Checking drivers/platform/x86/pcengines-apuv2.c it also appears to be
incomplete since it mentions different dmi board names depending on bios
version.

/* APU2 w/ legacy BIOS < 4.0.8 */ is 'APU2'
/* APU2 w/ legacy BIOS >= 4.0.8 */ is 'apu2'
/* APU2 w/ mainline BIOS */ is 'PC Engines apu2'

So the patch, if applicable at all, only 'works' for legacy BIOS >=
4.0.8

My APU2 on mainline BIOS reboots fine without this patch.  So let's see
if anyone screams and when they do question why legacy bios.  If patch
DOES need to be re-introduced then it needs to go upstream first.

Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
2021-03-24 11:51:29 +00:00
Kevin Darbyshire-Bryant
d07ac3e376 kernel: bump 5.10 to 5.10.25
Straightforward refresh of patches using update_kernel.

Removed (reverse-applicable):
bmips/patches-5.10/010-v5.11-net-dsa-implement-a-central-TX-reallocation-procedur.patch

Run tested: x86_64 (apu2)

Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
2021-03-24 11:39:05 +00:00
Kevin Darbyshire-Bryant
eb964298b3 kernel: bump 5.10 to 5.10.24
Straightforward refresh of patches using update_kernel.

Run tested: x86_64 (apu2)

Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
2021-03-24 11:36:31 +00:00
Álvaro Fernández Rojas
07c49462ad bmips: add wifi packages for supported devices
Netgear DGND3700v2 / Comtrend VR-3032u internal wireless not supported.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2021-03-23 20:23:47 +01:00
Álvaro Fernández Rojas
2024547e1f bmips: add ATH9K PCI fixups
Add support for registering ATH9K PCI fixups needed to bring up wifi on some
devices.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2021-03-23 20:16:37 +01:00
Álvaro Fernández Rojas
793047bb0f bmips: add B43 SPROM PCI fixups
Add support for registering fallback BCMA/SSB B43 SPROMs.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2021-03-23 20:14:38 +01:00
Álvaro Fernández Rojas
7f04d67517 bmips: add experimental PCI/PCIe support
These PCI drivers are a bit hacky and definitely not suitable for upstreaming,
but hopefully we can use them as a base for developing proper upstream PCI
drivers.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2021-03-23 20:12:22 +01:00
Adrian Schmutzler
851dadc257 realtek: add ZYXEL_VERS to DEVICE_VARS
Otherwise, the last defined value will be set for all devices.

Fixes: c6c8d597e1 ("realtek: Add generic zyxel_gs1900 image definition")

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-03-22 20:58:16 +01:00
Shiji Yang
bf7ddb18f1 ramips: speed up spi frequency for Youku YK-L1
Youku YK-L1 has a huge storage space up to 32 MB. It is better to
use a higher spi clock to read or write serial nor flash chips.
Youku YK-L1 has Winbond w25q256fvfg on board that can support
104 MHz spi clock so 48 MHz is safe enough.
The real frequency can only be sysclk(580MHz ) /3 /(2^n) so 80 MHz
defined in dts file will set only 48 MHz in spi bus.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2021-03-22 20:54:34 +01:00
Mauri Sandberg
e87527b57d ath79: copy cfi patch from 5.4 over to 5.10
Add the same patch to 5.10 too. The patch is in process of being
upstreamed.

Fixes: 8cc0fa8fac ("ath79: cfi: cmdset_0002: amd chip
0x2201 - write words")

Signed-off-by: Mauri Sandberg <sandberg@mailfence.com>
[add Fixes:]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-03-22 20:53:22 +01:00
Mauri Sandberg
bc356de285 ath79: Add support for Buffalo WZR-HP-G300NH
This device is a wireless router working on 2.4GHz band based on
Qualcom/Atheros AR9132 rev 2 SoC and is accompanied by Atheros AR9103
wireless chip and Realtek RTL8366RB/S switches. Due to two different
switches being used also two different devices are provided.

  Specification:
  - 400 MHz CPU
  - 64 MB of RAM
  - 32 MB of FLASH (NOR)
  - 3x3:2 2.4 GHz 802.11bgn
  - 5x 10/100/1000 Mbps Ethernet
  - 4x LED, 3x button, On/Off slider, Auto/On/Off slider
  - 1x USB 2.0
  - bare UART header place on PCB

  Flash instruction:
  - NOTE: Pay attention to the switch variant and choose the image to
    flash accordingly. (dmesg / kernel logs can tell it)
  - Methods for flashing
    - Apply factory image in OEM firmware web-gui.
    - Sysupgrade on top of existing OpenWRT image
    - U-Boot TFPT recovery for both stock or OpenWRT images:
      The device U-boot contains a TFTP server that by default has
      an address 192.168.11.1 (MAC 02:AA:BB:CC:DD:1A). During the boot
      there is a time window, during which the device allows an image to
      be uploaded from a client with address 192.168.11.2. The image will
      be written on flash automatically.

      1) Have a computer with static IP address 192.168.11.2 and the
         router device switched off.
      2) Connect the LAN port next to the WAN port in the device and the
         computer using a network switch.
      3) Assign IP 192.168.11.1 the MAC address 02:AA:BB:CC:DD:1A
         arp -s 192.168.11.1 02:AA:BB:CC:DD:1A
      4) Initiate an upload using TFTP image variant
         curl -T <imagename> tftp://192.168.11.1
      5) Switch on the device. The image will be uploaded subsequently.
         You can keep an eye on the diag light on the device, it should
         keep on blinking for a while indicating the writing of the image.

  General notes:
  - In the stock firmware the MAC address is the same among all
    interfaces so it is left here that way too.

  Recovery:
  - TFTP method
  - U-boot serial console

  Differences to ar71xx platform
  - This device is split in two different targets now due to hardware
    being a bit different under the hood. Dynamic solution within the same
    image is left for later time.
  - GPIOs for a sliding On/Off switch, marked 'Movie engine' on the device
    cover, were the wrong way around and were renamed qos_on -> movie_off,
    qos_off -> movie_on. Associated key codes remained the same they were.

  The device tree source code is mostly based on musashino's work

Signed-off-by: Mauri Sandberg <sandberg@mailfence.com>
2021-03-22 09:23:10 +01:00
Mauri Sandberg
8cc0fa8fac ath79: cfi: cmdset_0002: amd chip 0x2201 - write words
Generally, in upstream CFI flash memory driver uses buffers for write
operations. That does not work with AMD chip with id 0x2201 and we must
resort to writing word sized chunks only. That is, to not apply general
buffer write functionality for this given chip.

Without the patch kernel logs will be flooded with entries like below:

MTD do_erase_oneblock(): ERASE 0x01fa0000
MTD do_write_buffer(): WRITE 0x01fa0000(0x00001985)
MTD do_erase_oneblock(): ERASE 0x01f80000
MTD do_write_buffer(): WRITE 0x01f80000(0x00001985)
MTD do_write_buffer_wait(): software timeout, address:0x01f8000a.
jffs2: Write clean marker to block at 0x01a60000 failed: -5
MTD do_erase_oneblock(): ERASE 0x01f60000
MTD do_write_buffer(): WRITE 0x01f60000(0x00001985)
MTD do_write_buffer_wait(): software timeout, address:0x01f6000a.
jffs2: Write clean marker to block at 0x01a40000 failed: -5

References: http://patchwork.ozlabs.org/project/linux-mtd/patch/20210309174859.362060-1-sandberg@mailfence.com/
Signed-off-by: Mauri Sandberg <sandberg@mailfence.com>
[added link to usptream fix submission]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2021-03-22 09:23:10 +01:00
Rafał Miłecki
a49fd9db0a bcm4908: backport the latest bcm_sf2 commits
1. CFP support for BCM4908
2. Upstream RGMII regs fix

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-03-22 08:19:36 +01:00
Rafał Miłecki
13d9904acd bcm4908: backport DTS patch with Ethernet TX IRQ
It allows bcm4908_enet Linux driver to work more efficiently.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-03-22 07:45:34 +01:00
Rafał Miłecki
2b4986b942 bcm4908: add MTD support for repartitioning
It's required for sysupgrade which requires:
1. Flashing new firmware
2. Finding updated bootfs partition
3. Updating bootfs content

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-03-22 07:44:10 +01:00
Walter Sonius
46c0634b50 ath79: fix lan port display order for sitecom wlr-7100
Physical port order watched from the back of the device is:
4 / 3 / 2 / 1 / WAN which also matches corresponding leds.
This patch corrects LuCI switch webpage LAN port order.

Signed-off-by: Walter Sonius <walterav1984@gmail.com>
[improve commit title, fix sorting in 02_network]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-03-21 22:45:20 +01:00
John Audia
2c81b16964 kernel: bump 5.4 to 5.4.106
Ran update_kernel.sh in a fresh clone without any existing toolchains.

Manually rebased:
  bcm27xx/950-0993-xhci-quirks-add-link-TRB-quirk-for-VL805.patch
  layerscape/701-net-0231-enetc-Use-DT-protocol-information-to-set-up-the-port.patch

Build system: x86_64
Build-tested: ipq806x/R7800
Run-tested: ipq806x/R7800

No dmesg regressions, everything functional

Signed-off-by: John Audia <graysky@archlinux.us>
[remove accidental whitespace edit]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-03-21 22:45:20 +01:00
INAGAKI Hiroshi
b3ca1f30ef ramips: add support for ELECOM WRC-1750GST2
ELECOM WRC-1750GST2 is a 2.4/5 GHz band 11ac (Wi-Fi 5) router, based on
MT7621A.

Specification:

- SoC		: MediaTek MT7621A
- RAM		: DDR3 256 MiB (NT5CC128M16JR-EK)
- Flash		: SPI-NOR 32 MiB (MX25L25645GMI-08G)
- WLAN		: 2.4/5 GHz 3T3R (2x MediaTek MT7615)
- Ethernet	: 10/100/1000 Mbps x5
  - Switch	: MediaTek MT7530 (SoC)
- LEDs/Keys	: 4x/6x (2x buttons, 1x slide-switch)
- UART		: through-hole on PCB
  - J4: 3.3V, GND, TX, RX, from ethernet port side
  - 57600n8
- Power		: 12 VDC, 1.5 A

Flash instruction using factory image:

1. Boot WRC-1750GST2 normally with "Router" mode
2. Access to "http://192.168.2.1/" and open firmware update page
   ("ファームウェア更新")
3. Select the OpenWrt factory image and click apply ("適用") button
4. Wait ~120 seconds to complete flashing

MAC addresses:

LAN	: 04:AB:18:xx:xx:23 (Factory, 0xE000 (hex))
WAN	: 04:AB:18:xx:xx:24 (Factory, 0xE006 (hex))
2.4GHz	: 04:AB:18:xx:xx:25 (Factory, 0x4    (hex))
5GHz	: 04:AB:18:xx:xx:26 (Factory, 0x8004 (hex))

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2021-03-21 22:45:20 +01:00
Shiji Yang
df6154848a ramips: create shared DTSI for MT7620 Phicomm K2x series devices
Improve compatibility of the device tree include file. Now a new .dtsi
file will support both PSG1218A, PSG1218B and K2G.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
[improve commit title, rebase]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-03-21 22:45:20 +01:00
Shiji Yang
c36e47c5da ramips: increase SPI frequency for Phicomm series devices
From many teardown image in the internet, I find Phicomm K1/k2 series use
Winbond W25Q64/W25Q128 or GigaDevice GD25Q64/GD25Q128 Flash chips. both of
them support 100+ MHz clock spi operate and fast-read instruction. PSG1218
with W25x or GD25x has been tested and it can run well in OpenWrt v19.07.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
[improve commit title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-03-21 22:45:20 +01:00
Shiji Yang
d160b2c824 ramips: increase SPI frequency for HIWIFI HC5x61 devices
HIWIFI HC5x61 devices support high speed spi clock up to 100+ MHz.
So set spi frequency to 80 MHz here (Due to frequency division the
real clock is 48 MHz).
I have tested HC5661 and it can run well in OpenWrt v19.07.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
[adjust commit title and wrap message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-03-21 22:45:20 +01:00
Daniel Golle
310b7f76e8
mediatek: linksys-e8450: remove left-overs from dtsi
There is an ASMedia ASM1480 PCIe switch found on mt7622-rfb1 and the
BPi-R64, allowing the user to switch between SATA and PCIe1 which share
the same pins on the SoC.
This chip is not present on the Linksys E8450, it doesn't have SATA.
Remove definitions for GPIO90 from DTSI to prevent it from being
copy&pasted or otherwise causing confusion.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-03-21 13:38:42 +00:00
Álvaro Fernández Rojas
f93b544f01 bcm27xx: bcm2711: correctly disable HW_RANDOM_BCM2835
It was removed in bac74aff5e, but it should have been disabled.
More info: https://forum.openwrt.org/t/make-image-stops-at-random-number-generator-bcm27xx/91429/7

Fixes: bac74aff5e ("bcm27xx: bcm2711: disable HW_RANDOM_BCM2835")
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2021-03-21 12:39:47 +01:00
Hauke Mehrtens
0c0cb97da7 kernel: Add missing kernel config options
These two options are missing when building the x86 target.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2021-03-19 18:48:32 +01:00
Hauke Mehrtens
0b5a67aa03 kernel: Reorder kernel configuration options
Reorder the options and remove double entries.
This was generated by running this:
$ ./scripts/kconfig.pl '+' target/linux/generic/config-5.10 /dev/null > target/linux/generic/config-5.10.new
$ mv target/linux/generic/config-5.10.new target/linux/generic/config-5.10
$ ./scripts/kconfig.pl '+' target/linux/generic/config-5.4 /dev/null > target/linux/generic/config-5.4.new
$ mv target/linux/generic/config-5.4.new target/linux/generic/config-5.4

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2021-03-19 18:38:35 +01:00
Hauke Mehrtens
047b7621bb archs38: Add CONFIG_HZ=100
This kernel config option was missing and resulted in a question when
building.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2021-03-19 18:00:22 +01:00
Rosen Penev
a50441b6e9 kernel: add exfat again
With kernel 5.10, exfat is out of staging and in tree.

Added small hack to make it work with kernel 5.4 as well.

Added removed config options for 5.4 to generic config.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
[Set CONFIG_EXFAT_ config options to default values]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2021-03-19 16:08:12 +01:00
Tad Davanzo
b4f76d9f0d mvebu: enable WRT1900AC v1 and WRT32X for buildbots
Kernel size limits have been dealt with.
Effective revert of a1eb2c46 and ac9730c4.

Signed-off-by: Tad Davanzo <tad@spotco.us>
2021-03-19 15:30:01 +01:00
Tad Davanzo
15309f5133 mvebu: venom resize kernel to 6MB
venom has a 3MB kernel partition as specified by the DTS.
3MB is not sufficient for building with many kernel modules or newer
kernel versions.

venom uboot however as set from factory will load up to 6MB.
This can be observed by looking a uboot log:
	NAND read: device 0 offset 0x900000, size 0x600000
	6291456 bytes read: OK
and from uboot environment variables:
	$ fw_printenv | grep "priKernSize";
	priKernSize=0x0600000

Resize the root partitions from 120MB to 117MB to let kernel expand
into it another 3MB.
And set kernel target size to 6MB.

Lastly set the kernel-size-migration compatibility version on venom to
prevent sysupgrading without first reinstalling from a factory image.

Signed-off-by: Tad Davanzo <tad@spotco.us>
2021-03-19 15:30:01 +01:00
Tad Davanzo
10415d5e70 mvebu: mamba resize kernel to 4MB
mamba has a 3MB kernel partition as specified by the DTS.
3MB is not sufficient for building with many kernel modules or newer
kernel versions.

mamba uboot however as set from factory will load up to 4MB.
This can be observed by looking a uboot log:
	NAND read: device 0 offset 0xa00000, size 0x400000
	4194304 bytes read: OK
and from uboot environment variables:
	$ fw_printenv | grep "pri_kern_size";
	pri_kern_size=0x400000

Resize the root partitions from 37MB to 36MB to let kernel expand
into it another 1MB.
And set kernel target size to 4MB.

Lastly add a compatibility version message: kernel-size-migration.
And set it on mamba to prevent sysupgrading without first reinstalling from
a factory image.

Signed-off-by: Tad Davanzo <tad@spotco.us>
2021-03-19 15:30:01 +01:00
Tony Ambardar
9662da770e kernel: add missing config symbols, fix typos
Update 5.10 generic config to add missing options prompting during builds,
when setting CONFIG_ALL_KMODS. Refresh the x86 subtargets to drop symbols
added to the generic config.

Also fix a typo in 5.4/5.10 generic configs: "CONFIG_CONFIG_KVM_AMD_SEV".

Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
2021-03-19 14:02:47 +00:00
Daniel Golle
d0d63162b6
ipq806x: work-around vendor 'rootfs_data' GPT partition
ZyXEL NBG6817 comes with an eMMC which contains a GPT partition named
'rootfs_data'. This currently confuses fstools and makes it pick that
(not suitable) partition.
Use the newly introduced fstools_ignore_partname=1 kernel cmdline
parameter to have fstools ignore that partition.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-03-19 13:36:02 +00:00
Álvaro Fernández Rojas
df26c29629 bmips: backport b53 mmap device tree support
This patch has been accepted upstream for linux v5.13.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2021-03-19 11:00:19 +01:00
Álvaro Fernández Rojas
a139ab1b82 bmips: backport b53 legacy tags support
These patches have been accepted upstream for linux 5.13.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2021-03-19 11:00:19 +01:00
Álvaro Fernández Rojas
d6c5698a71 bmips: backport upstream dsa b53 is63xx patch
This patch has been accepted for linux v5.13.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2021-03-19 11:00:19 +01:00
Ilya Lipnitskiy
f65b0afadb ramips: move spi-nor-add-gd25q512 patch to generic
A SPI NOR flash should not be target-specific, so move it to generic in
case another platform needs to use it.

Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
2021-03-19 01:25:26 +01:00
Lech Perczak
410fb05b44 rampis: use lzma-loader for ZTE MF283+
Without that, after merging support to master, the device fails to boot
due to LZMA decompression error:

3: System Boot system code via Flash.
## Booting image at bc080000 ...
raspi_read: from:80000 len:40
.   Image Name:   MIPS OpenWrt Linux-5.4.99
   Created:      2021-02-25  23:35:00 UTC
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    1786664 Bytes =  1.7 MB
   Load Address: 80000000
   Entry Point:  80000000
raspi_read: from:80040 len:1b4328
............................   Verifying Checksum ... OK
   Uncompressing Kernel Image ... LZMA ERROR 1 - must RESET board to recover

Use lzma-loader to fix it.

Fixes: 59d065c9f8 ("ramips: add support for ZTE MF283+")
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
2021-03-19 01:25:26 +01:00
Shiji Yang
a94a20373b ramips: improve GPIO pin control for HC5x61
HC5661 does not have USB port, remove usb power control pin.
HC5x61 do not have LAN LEDs, remove ethernet LED control pin.
Only HC5861 has PA in 2.4G channel.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2021-03-19 01:25:26 +01:00
Aleksander Jan Bajkowski
12e942b1fd kernel: move some disabled symbols to generic
Move some disabled symbols found in armvirt target to generic.

Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
2021-03-19 00:59:22 +01:00
Aleksander Jan Bajkowski
c027dbac5a lantiq: set maximum kernel size for ARV7519RW22
Some users report that current snapshot producies non-bootable images.
Stock uboot can boot images if the kernel is smaller than 2MB.

Set maximum kernel size and disable image building for this board.

Ref: https://forum.openwrt.org/t/astoria-arv7519rw22-bootloops-after-upgrade/89843
Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
2021-03-18 16:17:43 +01:00
David Bauer
42d943f40a mediatek: fix broken UniFi 6 LR image
Ubiquiti's own bootloader expects the configuration mode to be present
with a "@" instead of a "-" for the sperator character. Otherwise
booting of the image fails.

Signed-off-by: David Bauer <mail@david-bauer.net>
2021-03-18 00:56:33 +01:00
David Bauer
ac5675ec8f ramips: fix broken UniFi 6 Lite image
Ubiquiti's own bootloader expects the configuration mode to be present
with a "@" instead of a "-" for the sperator character. Otherwise
booting of the image fails.

Signed-off-by: David Bauer <mail@david-bauer.net>
2021-03-18 00:54:25 +01:00
Hauke Mehrtens
0e3f6fbe10 mediatek: Fix writing U-Boot env on Buffalo WSR-2533DHP2
This fixes writing to the U-Boot environment by making the partition
writable and setting the correct flash sector size of 128K.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2021-03-17 22:39:59 +00:00
Daniel Golle
b40f707f71 mediatek: bpi-r64: use dt-overlay to select SATA or PCIE1
The Bananapi BPi-R64 got a SATA interface which cannot be used at the
same time as the second mPCIe slot. The decission is made by hogging
GPIO 90.
Embed two addtional DT overlay blobs into the image to allow bootloader
selection of either SATA or PCIE1 feature.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-03-17 19:12:19 +00:00
Daniel Golle
53a7d5d614 ath79: fix RS-485 on Teltonika RUT-955
DTR GPIO isn't actually needed and triggers boot warning.
TX pin was off by one (GPIO 19 instead of GPIO 18).

Reported-by: @tophirsch
Fixes: d1130ad265 ("ath79: add support for Teltonika RUT955")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-03-17 17:41:24 +00:00
Tony Ambardar
6eca2e40e7 malta: prune subtarget configs
Drop autogenerated kernel config options. These aren't needed to build and
can obscure options relevant to the subtarget.

Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
2021-03-17 15:35:33 +01:00
Tony Ambardar
fd1c285040 malta: update kernel 5.10 configs
Update generic config to add missing options that prompt during builds. Run
"make kernel_oldconfig" to refresh malta target config.

Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
2021-03-17 15:35:33 +01:00
Tony Ambardar
3e2f42a802 malta: support kernel 5.10
Add linux 5.10 as testing kernel and copy generic config from 5.4.

Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
2021-03-17 15:35:33 +01:00
Bjørn Mork
963b2ae702 realtek: enable SerDes NWAY and SGMII negotiation
This allows copper SFPs to negotiate speeds lower than 1gig.

Acked-by: Birger Koblitz <mail@birger-koblitz.de>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
2021-03-17 10:01:21 +01:00
Bjørn Mork
07bf5aaa4c realtek: enabled Marvell and Realtek PHYs
The rtl83xx-phy driver is necessary for proper configuration of the
PHYs if U-Boot hasn't done that.

1000Base-T SFPs often contains a Marvell 88E1111 and will not work
without this driver. Include it by default to support copper SFPs.

Signed-off-by: Bjørn Mork <bjorn@mork.no>
2021-03-17 10:01:21 +01:00
Bjørn Mork
2a912fb63a realtek: enable HWMON for SFP sensors
This adds SFP sensors as a hwmon device, allowing readout of
temperatures, DOM and other sensor readings available from the
SFP.  Example from a ZyXEL GS1900-10HP with a DOM capable
1000Base-SX SFP:

root@gs1900-10hp:~# grep . /sys/class/hwmon/hwmon0/*
/sys/class/hwmon/hwmon0/curr1_crit:90
/sys/class/hwmon/hwmon0/curr1_crit_alarm:0
/sys/class/hwmon/hwmon0/curr1_input:4
/sys/class/hwmon/hwmon0/curr1_label:bias
/sys/class/hwmon/hwmon0/curr1_lcrit:0
/sys/class/hwmon/hwmon0/curr1_lcrit_alarm:0
/sys/class/hwmon/hwmon0/curr1_max:85
/sys/class/hwmon/hwmon0/curr1_max_alarm:0
/sys/class/hwmon/hwmon0/curr1_min:0
/sys/class/hwmon/hwmon0/curr1_min_alarm:0
/sys/class/hwmon/hwmon0/in0_crit:3795
/sys/class/hwmon/hwmon0/in0_crit_alarm:0
/sys/class/hwmon/hwmon0/in0_input:3317
/sys/class/hwmon/hwmon0/in0_label:VCC
/sys/class/hwmon/hwmon0/in0_lcrit:2805
/sys/class/hwmon/hwmon0/in0_lcrit_alarm:0
/sys/class/hwmon/hwmon0/in0_max:3465
/sys/class/hwmon/hwmon0/in0_max_alarm:0
/sys/class/hwmon/hwmon0/in0_min:3135
/sys/class/hwmon/hwmon0/in0_min_alarm:0
/sys/class/hwmon/hwmon0/name:sfp_p10
/sys/class/hwmon/hwmon0/power1_crit:708
/sys/class/hwmon/hwmon0/power1_crit_alarm:0
/sys/class/hwmon/hwmon0/power1_input:259
/sys/class/hwmon/hwmon0/power1_label:TX_power
/sys/class/hwmon/hwmon0/power1_lcrit:89
/sys/class/hwmon/hwmon0/power1_lcrit_alarm:0
/sys/class/hwmon/hwmon0/power1_max:501
/sys/class/hwmon/hwmon0/power1_max_alarm:0
/sys/class/hwmon/hwmon0/power1_min:126
/sys/class/hwmon/hwmon0/power1_min_alarm:0
/sys/class/hwmon/hwmon0/power2_crit:1259
/sys/class/hwmon/hwmon0/power2_crit_alarm:0
/sys/class/hwmon/hwmon0/power2_input:404
/sys/class/hwmon/hwmon0/power2_label:RX_power
/sys/class/hwmon/hwmon0/power2_lcrit:6
/sys/class/hwmon/hwmon0/power2_lcrit_alarm:0
/sys/class/hwmon/hwmon0/power2_max:794
/sys/class/hwmon/hwmon0/power2_max_alarm:0
/sys/class/hwmon/hwmon0/power2_min:10
/sys/class/hwmon/hwmon0/power2_min_alarm:0
/sys/class/hwmon/hwmon0/temp1_crit:100000
/sys/class/hwmon/hwmon0/temp1_crit_alarm:0
/sys/class/hwmon/hwmon0/temp1_input:22547
/sys/class/hwmon/hwmon0/temp1_label:temperature
/sys/class/hwmon/hwmon0/temp1_lcrit:-50000
/sys/class/hwmon/hwmon0/temp1_lcrit_alarm:0
/sys/class/hwmon/hwmon0/temp1_max:85000
/sys/class/hwmon/hwmon0/temp1_max_alarm:0
/sys/class/hwmon/hwmon0/temp1_min:-40000
/sys/class/hwmon/hwmon0/temp1_min_alarm:0
/sys/class/hwmon/hwmon0/uevent:OF_NAME=sfp-p10
/sys/class/hwmon/hwmon0/uevent:OF_FULLNAME=/sfp-p10
/sys/class/hwmon/hwmon0/uevent:OF_COMPATIBLE_0=sff,sfp
/sys/class/hwmon/hwmon0/uevent:OF_COMPATIBLE_N=1

Tested-by: Birger Koblitz <mail@birger-koblitz.de>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
2021-03-17 10:01:21 +01:00
Bjørn Mork
e8d391bd46 realtek: re-enable sfp driver for ZyXEL GS1900-10HP
There is no need to define a static link or a phy for the sfp
ports.  Using phy-mode and managed properties to  describe the
link to the sfp phy.

We have to keep the now unconnected virtual "phys" because the
switch  driver uses their "phy-is-integrated" property to figure
out which ports to enable as fibre ports.

Acked-by: Birger Koblitz <mail@birger-koblitz.de>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
2021-03-17 10:01:21 +01:00
Bjørn Mork
785d830e88 realtek: need to handle PHY_INTERFACE_MODE_NA for sfps
From the validate docs in include/linux/phylink.h:

 When state->interface is PHY_INTERFACE_MODE_NA, phylink expects the
 MAC driver to return all supported link modes.

Tested-by: Birger Koblitz <mail@birger-koblitz.de>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
2021-03-17 10:01:21 +01:00
Bjørn Mork
b8e473d18c realtek: fix link-state interrupt
This bug was the root cause for the failing sfp driver.

Acked-by: Birger Koblitz <mail@birger-koblitz.de>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
2021-03-17 10:01:21 +01:00
Rafał Miłecki
e1b4fd52a8 bcm4908: backport recent bcm_sf2 changes
One 5.12 link fix and 5.13 crossbar support.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-03-17 08:10:54 +01:00
Rafał Miłecki
7091e31230 bcm4908: backport recent bcm4908_enet changes
This includes 5.12 fix and 5.13 improvements.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-03-16 23:57:52 +01:00
Álvaro Fernández Rojas
34f898ec29 bmips: backport bcm6368-mdio-mux support
This patch has been accepted for linux v5.13.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2021-03-16 20:06:00 +01:00
Álvaro Fernández Rojas
7ec9d95567 bmips: enable CONFIG_B53_MDIO_DRIVER
Some devices have external switches connected by MDIO.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2021-03-16 20:00:51 +01:00
Álvaro Fernández Rojas
b434c524b1 bmips: backport b53 spi device tree patch
This patch has been accepted for linux v5.13.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2021-03-16 20:00:51 +01:00
Álvaro Fernández Rojas
be16951494 bmips: dgnd3700-v2: fix ethernet
This is a temporary workaround to get the ethernet working, since external
switch is connected by MDIO and it needs additional work.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2021-03-16 20:00:51 +01:00
Ilya Lipnitskiy
680f91d0e5 kernel: backports: mt7530: fix TRGMII mode after reset
Backport upstream patch that fixes TRGMII mode now that mt7530 is
actually resetting the switch on ramips devices.

Patches apply to both Linux 5.4 and 5.10, since TRGMII is broken on both.

Fixes: 69551a2442 ("ramips: manage low reset lines")
Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
2021-03-16 19:27:55 +08:00
Tony Ambardar
662ceebc4c x86/legacy: fix subtarget CPU for kernel 5.10
The 5.10 target config defined a baseline i686 CPU aligned to the 32-bit
generic subtarget. However, the legacy subtarget arch wasn't set to the
older 586MMX, defaulting instead to the i686.

Explicitly set the subtarget arch and refresh the subtarget config, as done
already with the old geode subtarget.

Fixes: 8391781389 ("x86: support kernel 5.10")
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
2021-03-15 19:12:03 -07:00
Rafał Miłecki
d7c8ca4d0b bcm4908: backport first PHY 5.13 patches
1. Upstream accepted version of Kconfig change
2. Documentation binding fix

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-03-15 20:30:21 +01:00
Daniel Golle
c17b1dca60
mediatek: mt7622: drop duplicate DEVICE_PACKAGES
kmod-mt7615e kmod-mt7615-firmware and uboot-envtools are already part
of the target's default package set. No need to add them again for
buffalo_wsr-2533dhp2.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-03-15 16:40:31 +00:00
INAGAKI Hiroshi
74f15628dd mediatek: add support for Buffalo WSR-2533DHP2
This adds support for the Buffalo WSR-2533DHP2.

The device uses the Broadcom TRX image format with a special magic. To
be able to boot the images or load them they have to be wrapped with
different headers depending how it is loaded.

There are multiple ways to install OpenWrt on this device.
Boot ramdisk from U-Boot
----------------------------
This will load the image and not write it into the flash.

1. Stop boot menu with "space" key
2. Select "System Load Linux to SDRAM via TFTP."
3. Load this image:
   openwrt-mediatek-mt7622-buffalo_wsr-2533dhp2-initramfs-kernel.bin
4. The system boots the image

Write to flash from U-Boot
-----------------------------
This will load the image over tftp and directly write it into the flash.

1. Stop boot menu with "space" key
2. Select "System Load Linux Kernel then write to Flash via TFTP."
3. Load this image:
   openwrt-mediatek-mt7622-buffalo_wsr-2533dhp2-squashfs-factory-uboot.bin
4. The system writes this image into the flash and boots into it.

Write to flash from Web UI
-----------------------------
This will load the image over over the Web UI and write it into the flash

1. Open the Web UI
2. Go to "管理" -> "ファームウェア更新"
3. Select "ローカルファイル指定" and click "更新実行"
4. Load this image:
   openwrt-mediatek-mt7622-buffalo_wsr-2533dhp2-squashfs-factory.bin
5. The system writes this image into the flash and boots into it.

Specifications
-------------------
* SoC:       MT7622 (4x4 2.4 GHz Wifi)
* Wifi:      MT7615 (4x4 5 GHz Wifi)
* Flash:     Winbond W29N01HZ 128MB SLC NAND
* RAM        256MB
* Ethernet:  Realtek RTL8367S (5 x 1GBit/s, SoC via 2.5GBit/s)

Co-Developed-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2021-03-15 17:02:17 +01:00
Hauke Mehrtens
58c5e25664 mediatek: support non standard trx magic values
Buffalo uses the TRX format with a different magic, add support for
this.

It is planned to send these patches upstream.

Cc: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2021-03-15 16:57:34 +01:00
Hauke Mehrtens
cb740fbe25 mediatek: fix mtk parallel nand driver
This fixes some bugs in the mtk parallel nand driver introduced in 5.10.

This patch was send upstream.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2021-03-15 16:57:34 +01:00