The port is labeled as wan and was only used as lan port because of the
"tx ring full" issues fixed with 8f02f7c.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Using the lantiq,wan device tree property for one interface node and
the lantiq,switch device tree property for another interface node at
the same time was never intended/isn't supported at the moment.
The property is meant to be used in two phy operation mode where one
phy is assigned to an interface without lantiq,* device tree property
and the other phy is assigned to an interface with the lantiq,wan
device property to have two netdevs.
If both properties are used at the same time, the lantiq,wan interface
is shown as independent netdev but not able to operate independent. The
port needs to be managed via swconfig. These dependency is not obvious
and fooled already a lot of users.
Add a default WAN vlan for xrx200 devices having an ethernet WAN port
and remove the lantiq,wan device tree property. Leave it up to the user
to set the ethernet WAN port as default WAN interface or to use this
port as additional LAN port.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The two phy operation mode where one phy is assigned to an interface
without lantiq,* device tree property and the other phy is assigned to
an interface with the lantiq,wan device property was broken with the
multicast package leaks between vlans fixes.
Move the multicast packages relevant portmap settings to the condition
which handles multicast packages for better readability.
Replace the priv->port_map based port_map only for the interface which
has the lantiq,switch device tree property set, to allow tagged
multicast packages in two phy mode where the lantiq,switch device tree
property isn't used.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The ASL56026 is a VDSL2 router with dual 100mbit ethernet,
also known as the ECI B-FOCuS V-2FUb/I.
CPU: Lantiq XRX268 v1.1 at 333MHz
Modem: Lantiq VRX208
RAM: 32MiB DDR2 at 167MHz
Flash: 8MiB NOR, Spansion S29GL064N90TF04
UART is at JP1:
Pin 1 TX
Pin 2 GND
Pin 3 +3.3V
Pin 4 NC
Pin 5 RX
Boot selection pins are exposed via several resistor jumpers:
boot_sel0 is at J15, on the rear of the board. Default is high.
boot_sel1 is at J3, next to the flash - it is also the flash CE# pin. Default is low.
boot_sel2 is at J12, directly below the SoC. Default is low.
boot_sel3 is at J16, on the rear of the board. Default is low.
The boot_sel pins should never be shorted, the jumper must be moved or
a lower value resistor used to change the pull (existing resistors are 4k7, 1k should work)
To install with the stock bootloader you must break the built in image selection process
which uses at least the following vars: f_upgrade_addr, f_upgrade2_addr, loadaddr, kernel_addr, activeregion, committedregion
This is done by setting loadaddr and both f_upgrade_addr vars to the same address:
VR9 # setenv loadaddr 0xB0040000
VR9 # setenv f_upgrade_addr 0xB0040000
VR9 # setenv f_upgrade2_addr 0xB0040000
VR9 # saveenv
Then flash the firmware image:
VR9 # tftpboot 0x81000000 lede-lantiq-xrx200-ASL56026-squashfs-sysupgrade.bin
VR9 # erase B0040000 +${filesize}
VR9 # cp.b 0x81000000 0xB0040000 ${filesize}
Signed-off-by: Alex Maclean <monkeh@monkeh.net>
The ethernet driver uses a port map override via special tag to control
the ports on which multicast packets are sent. This was added to work
around an issue in the switch that was occasionally leaking packets onto
the wrong vlan.
Unfortunately the change had some leftover lines that were overwrting
the port map with a list of all ports, thus always leaking packets onto
the wront vlan.
Fix this by only enabling the override with the VLAN port map and only
if a matching VLAN port map was actually found
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Fixes the following warning on first boot if the ltq_atm modules are
not included in the image:
ls: /lib/modules/4.4.49/ltq_atm*: No such file or directory
Signed-off-by: Mathias Kresin <dev@kresin.me>
Use the nas0 interface for the netdev trigger as default. Use the ptm0
interface for xRX200 boards to match the default wan interface set in
02_network.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Move the code to check if the current system is a system with vdsl
support to a dedicate function to make it reusable.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The firmware hotplug script tries to read the mac address from a
partition with the name "uboot-env" which does not exist (instead it's
name is uboot_env). This broke calculation of the new checksum (after
patching the mac address) which resulted in ath9k refusing to use the
EEPROM data.
The original error reported by ath9k was:
PCI: Enabling device 0000:00:0e.0 (0000 -> 0002)
ath: phy0: Bad EEPROM checksum 0x2523
ath: phy0: Unable to initialize hardware; initialization status: -22
ath9k 0000:00:0e.0: Failed to initialize device
Fixes: a20616863d ("lantiq: use ath9k device tree bindings
binding/owl-loader")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Do not put the probe function into the __init section, but use the normal
section. This fixes a section mismatch warning.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The following patches were dropped because they are already applied
upstream:
0012-pinctrl-lantiq-fix-up-pinmux.patch
0013-MTD-lantiq-xway-fix-invalid-operator.patch
0014-MTD-lantiq-xway-the-latched-command-should-be-persis.patch
0015-MTD-lantiq-xway-remove-endless-loop.patch
0016-MTD-lantiq-xway-add-missing-write_buf-and-read_buf-t.patch
0017-MTD-xway-fix-nand-locking.patch
0044-pinctrl-lantiq-introduce-new-dedicated-devicetree-bi.patch
0045-pinctrl-lantiq-Fix-GPIO-Setup-of-GPIO-Port3.patch
0046-pinctrl-lantiq-2-pins-have-the-wrong-mux-list.patch
0047-irq-fixes.patch
0047-mtd-plat-nand-pass-of-node.patch
0060-usb-dwc2-Add-support-for-Lantiq-ARX-and-XRX-SoCs.patch
0120-MIPS-lantiq-add-support-for-device-tree-file-from-bo.patch
0121-MIPS-lantiq-make-it-possible-to-build-in-no-device-t.patch
122-MIPS-store-the-appended-dtb-address-in-a-variable.patch
The PHY driver was reduced to the code adding the LED configuration,
the rest is already upstream:
0023-NET-PHY-adds-driver-for-lantiq-PHY11G.patch
The SPI driver was replaced with the version pending for upstream
inclusion:
New driver:
0090-spi-add-transfer_status-callback.patch
0091-spi-lantiq-ssc-add-support-for-Lantiq-SSC-SPI-controller.patch
Old driver:
0100-spi-add-support-for-Lantiq-SPI-controller.patch
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Use a vendor prefix as it has to be for all not core driver. Update the
compatible string in the device tree files accordingly.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The VGV7510KW22BRN and VGV7519BRN do not have the same brnImage
signature. It was accidentally changed with ba42c1d ("lantiq: un-macro
the image building code").
Signed-off-by: Mathias Kresin <dev@kresin.me>
Disabling ethernet during reboot (only to enable it again when the
ethernet driver attaches) can put the chip into a faulty state where it
corrupts the header of all incoming packets.
This happens if packets arrive during the time window where the core is
disabled, and it can be easily reproduced by rebooting while sending a
flood ping to the broadcast address.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Since the MIPS IRQ stack patches, lantiq devices were emitting a storm
of messages like this:
[ 567.872172] Spurious IRQ: CAUSE=0x1100c300
Fix this by reworking the IRQ dispatch code
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Prevents crashes when IRQs arrive when the current kernel stack context
already contains deeply nested function calls, e.g. when stacking lots
of network devices on top of each other
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This adds USB initialization fixes for Danube, Amazon SE and xrx300 and
should fix the clock on at least Danube which hopefully closes FS#351.
The xrx200 usb driver now uses more memory for the dwc2 fifos, this was
increased in the chip compared to ar9.
This is based in part on the vendor documentation and the vendor code
base as a reference.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The DMA controller used only local locks, which will not lock the
section against other CPUs, fix this by using spin locks.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The boot loader of many boards provides a kernel boot argument with a
broken console parameter to the kernel. This will be taken before the
stdout-path defined in device tree and the serial will not work on this
board. Multiple boards are affected by this problem, so revert this
patch for all boards. Later we can remove the boot arguments from the
device tree again, after the individual board was checked to work.
This partly reverts this commit:
commit 4995c64857
Author: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Date: Sun Dec 11 21:55:00 2016 +0100
lantiq: specify console using stdout-path instead of cmdline argument
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The following commit changed the build templates name but forgot to
update the TARGET_DEVICES variable properly.
commit f9226158be (lantiq: rename EASY98000 to EASY98000NOR)
Signed-off-by: John Crispin <john@phrozen.org>
The power LED can not be used for indicating the xDSL line state and
the in system (boot) state at the same time in LEDE. As soon as the
xDSL Line goes down, the power LED is switched off.
During xDSL handshake the power led would blink with the same or a
similar pattern as during boot.
Both might confuse users.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Due to a hardware bug of Atheros 8030 phys, the driver need to reset
the phys on link state change.
Use the correct compatible string for the at903x phys connected to
switch port 0 and 1.
Fix the pinmux of the gpio lines connected to the reset pin of the phys
and define the reset-pins to let the driver do the fixups.
Fixes FS#343
Signed-off-by: Mathias Kresin <dev@kresin.me>
/etc/preinit has been the default init-script for a very long time (at
least since Linux 2.6.30 in OpenWrt). Remove the kernel command line
"init" parameter to get rid of duplicate and inconsistent definitions
of this parameter (some boards, like FRITZ3370 for example did not use
it at all, while it's just copy and paste on others).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Use devicetree's /chosen/stdout-path instead of the kernel command line
(embedded in the .dts-files) to specify the serial console. Using the
chosen node is recommended on devicetree based platforms.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
This attribute is not evaluated any more and the boot loader on these
reference boards does not provide a broken root= or console= parameter.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add an extra function to patch the mac and fixup the checksum
afterwards. Calculate the checksum position automatically. The offset
to the mac address is the same for all checksum protected EEPROMs.
No EEPROM requires a byte swapped mac address. The mac byte swap code
was required due to an bug in the script that is now fixed.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The EEPROM data in the flash of the ARV7518PW, ARV8539PW22,
BTHOMEHUBV2B and BTHOMEHUBV3A is stored byte-swapped (swab16), meaning
that for example the ath9k base_eep_header fields "version" (high and
low byte), "opCapFlags" and "eepMisc" are swapped (the latter ones are
just 1 byte wide, thus their position is swapped).
The old "ath,eep-endian" property enabled the corresponding swapping
logic in the ath9k driver (swab16 in ath9k_hw_nvram_swap_data, which is
based on the magic bytes in the EEPROM data which have nothing to do
with the calibration data - thus this logic should not be used
anymore).
Since we have switched to the upstream ath9k devicetree bindings there
is no binding anymore which enables swab16 in ath9k (as this logic is
not recommended anymore as explained above), leading to ath9k
initialization errors:
ath: phy0: Bad EEPROM VER 0x0001 or REV 0x00e0
(this shows that the version field is swapped, expected values are VER
0x000E and REV 0x0001)
Swapping the ath9k calibration data when extracting it from the flash
fixes the devices listed above (all other devices do not require
additional swapping, since the position of the fields is already as
expected by ath9k). This allows ath9k to read the version correctly
again, as well as the more important "eepmisc" field (which is used for
determining whether the data inside the EEPROM is Big or Little Endian
which is required to parse the EEPROM contents correctly).
Fixes: a20616863d ("lantiq: use ath9k device tree bindings
binding/owl-loader")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Refresh patches on all 4.4 supported platforms.
077-0005-bgmac-stop-clearing-DMA-receive-control-register-rig.patch
removed as now upstream.
Compile & run tested: ar71xx - Archer C7 v2
Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
ifxhcd never had roothub support but since kernel 3.x it was expected
that a roothub always exists.
The patched fixed a null pointer deref in the usb subsystem because of
the missing roothub.
Since ifxhcd is gone, this whole patch isn't required any longer.
Signed-off-by: Mathias Kresin <dev@kresin.me>
This way the on nand bad block table is preserved and used. Add support
for nand OOB ECC checksums as well. It should fix all reported ubi
errors, which were all related to bad nand blocks and a purged on nand
bad block table.
The existing ubi partition will be reused, which eliminates the need
to touch the caldata during initial install. The BT u-boot has support
for loading a kernel from an ubi volume. It isn't necessary any longer
to replace the BT u-boot with a custom compiled one to use LEDE.
It is required to restore the BT Firmware and install LEDE from scratch
to switch to the new partition layout.
An image for restoring the BT firmware and installing LEDE is provided
at https://github.com/mkresin/lede/releases.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Backport upstream commit a61ae81a1907af1987ad4c77300508327bc48b23.
The actually purpose of the patch was to do some cleanup. As a side
effect of this cleanup, the device node is now passed to nand_dt_init.
This allows to use the common nand device tree properties
- nand-bus-width
- nand-on-flash-bbt
- nand-ecc-mode
- nand-ecc-step-size
- nand-ecc-strength
for the plat_nand driver.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Due to the addition of the bindings to the ath9k driver, this code
isn't used any longer. The fixup is now done by the owloader.
Rename the ath_eep.c file to ath5k_eep.c to indicate that this files
includes ath5k related code only.
Signed-off-by: Mathias Kresin <dev@kresin.me>
This moves the extraction of the eeprom/calibration data to a hotplug
firmware script. Additionally it modifies all .dts to configure ath9k
directly from within the .dts.
The owl-loader approach enables support on devices with exotic eeprom
data locations (such as unaligned positions on the flash or data
inside an UBI volume).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
[add ath9k caldata mac address patcher]
[fixes DGN3500 wifi mac]
[fixes BTHOMEHUBV3A wifi mac]
[set invalid mac for BTHOMEHUB2B, FRITZ3370, FRITZ7320 & FRITZ7360SL to restore previous random mac behavior]
Signed-off-by: Mathias Kresin <dev@kresin.me>
This adds support for the Intel Falcon SoC for GPON.
Support for the Falcon SoC was removed in commit c821836395 svn rev:
40392 from OpenWrt, this commit adds it again.
This patch adds a new subtarget for the Falcon SoC, but it still misses
all the drivers needed to control the GPON part.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The DEVICE_PACKAGES are not included in the initramfs image in case
TARGET_PER_DEVICE_ROOTFS is set. This might produces initramfs images
with a not working network configuration because of a missing swconfig.
Workaround the issues by adding the essential swconfig package to the
default packages selection and deselect swconfig for boards not having
swconfig included before via device packages.
Signed-off-by: Mathias Kresin <dev@kresin.me>
