The WPS button was mapped to the restart/reset. This patch
changes it to emit the KEY_WPS_BUTTON keycode so pressing
the WPS button does initiate WPS.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This applies several style adjustments that have been requested in
recent reviews to older DTS files. Despite making the code base more
consistent, this will also help to reduce review time when DTSes
are copy/pasted.
Applied changes:
- Rename gpio-keys/gpio-leds to keys/leds
- Remove node labels that are not used
- Use label property for partitions
- Prefix led node labels with "led_"
- Remove redundant includes
- Harmonize new lines after status property
- Several smaller style fixes
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This converts all remaining devices to use interrupt-driven
gpio-keys compatible instead of gpio-keys-polled.
The poll-interval is removed.
Only ar7240_netgear_wnr612-v2 is kept at gpio-keys-polled, as
this one is using ath9k keys.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: Karl Palsson <karlp@etactica.com>
Tested-by: Dmitry Tunin <hanipouspilot@gmail.com>
Commit "generic: ar8216: add mib_poll_interval switch attribute" sets
mib-poll-interval as disabled by default (was set to 2s), so it makes
switch LEDs trigger disfunctional on devices which don't have
mib-poll-interval set.
So this patch sets mib-poll-interval to 500ms on devices which have
ar83xx switch connected to mdio0 bus, as the same value was set for
built in switches in 443fc9ac35 ("ath79: use ar8216 for builtin
switch").
Some measurements performed on TP-Link Archer C7-v5:
mib-type=0, mib-poll-interval=500ms (10s pidstat)
Average: %usr %system %guest %wait %CPU CPU Command
Average: 0.00 1.93 0.00 0.00 1.93 - kworker/0:2
iperf3 (30s): 334 Mbits/sec
mib-type=0, mib-poll-interval=2s (10s pidstat)
Average: %usr %system %guest %wait %CPU CPU Command
Average: 0.00 1.14 0.00 0.00 1.14 - kworker/0:2
iperf3 (30s): 334 Mbits/sec
So it seems like we get 4x faster LED refresh rate for additional 0.8%
CPU load.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Hardware spec of DIR-859 A1:
SoC: QCA9563
DRAM: 64MB DDR2
Flash: 16MB SPI-NOR
Switch: QCA8337N
WiFi 5.8GHz: QCA9880
USB is supported on the PCB but not connected.
Flash instructions:
1. Upgrade the factory.bin through the factory web interface or the u-boot
failsafe interface.
The firmware will boot up correctly for the first time.
Do not power off the device after OpenWrt has booted. Otherwise the u-boot
will enter failsafe mode as the checksum of the firmware has been changed.
2. Upgrade the sysupgrade.bin in OpenWrt.
After upgrading completes the u-boot won't complain about the firmware
checksum and it's OK to use now.
3. If you powered off the device before upgrading the sysupgrade.bin, just
upgrade the factory.bin through the u-boot failsafe interface and then goto
step 2.
Signed-off-by: Weijie Gao <hackpascal@gmail.com>
[squash commits, use common seama recipes, sync factory image recipe
with ramips version]
Signed-off-by: Mathias Kresin <dev@kresin.me>
