This patch fixes the occurences of the following warning
message from the dtc:
Warning (reg_format): /soc/spi@78b5000/flash0@0/partitions/partition@0:reg:
property has invalid length (8 bytes) (#address-cells == 2, #size-cells == 1)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
SOC: IPQ4018 / QCA Dakota
CPU: Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7
DRAM: 256 MiB
NOR: 32 MiB
ETH: Qualcomm Atheros QCA8072 (1 port)
WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2
WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2
INPUT: RESET Button
LEDS: White, Blue, Red, Orange
Flash instruction:
From EnGenius firmware to OpenWrt firmware:
In Firmware Upgrade page, upgrade your openwrt-ipq40xx-generic-engenius_emd1-squashfs-factory.bin directly.
From OpenWrt firmware to EnGenius firmware:
1. Setup a TFTP server on your computer and configure static IP to 192.168.99.8
Put the EnGenius firmware in the TFTP server directory on your computer.
2. Power up EMD1. Press 4 and then press any key to enter u-boot.
3. Download EnGenius firmware
(IPQ40xx) # tftpboot 0x84000000 openwrt-ipq40xx-emd1-nor-fw-s.img
4. Flash the firmware
(IPQ40xx) # imgaddr=0x84000000 && source 0x84000000:script
5. Reboot
(IPQ40xx) # reset
Signed-off-by: Yen-Ting-Shen <frank.shen@senao.com>
[removed BOARD_NAME]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Specifications
==============
- SOC: IPQ4018
- RAM: DDR3 256MB
- Flash: SPI NOR 16MB
- WiFi:
- 2.4GHz: IPQ4018, 2x2, front end SKY85303-11
- 5GHz: IPQ4018, 2x2, front end SKY85717-21
- Ethernet: 1x 10/100/1000Mbps, POE 802.3af
- PHY: QCA8072
- UART: GND, blocked, 3.3V, RX, TX / 115200 8N1
- LED: 1x red / green
- Button: 1x reset / factory default
- U-Boot bootloader with tftp and "emergency web server" accessible
using serial port.
Installation
============
Flash factory image from D-Link web UI. Constraints in the D-Link web UI
makes the factory image unnecessarily large. Flash again using
sysupgrade from inside OpenWrt to reclaim some flash space.
Return to stock D-Link firmware
===============================
Partition layout is preserved, and it is possible to return to the stock
firmware simply by downloading it from D-Link and writing it to the
firmware partition.
# mtd -r write dap2610-firmware.bin firmware
Quirks
======
To be flashable from the D-Link http server, the firmware must be larger
then 6MB, and the size in the firmware header must match the actual file
size. Also, the boot loader verifies the checksum of the firmware before
each boot, thus the jffs2 must be after the checksum covered part. This
is solved in the factory image by having the rootfs at the very end of
the image (without pad-rootfs).
The sysupgrade image which does not have to be flashable from the D-Link
web UI may be smaller, and the checksum in the firmware header only
covers the kernel part of the image.
Signed-off-by: Fredrik Olofsson <fredrik.olofsson@anyfinetworks.com>
[added WRGG Variables to DEVICE_VARS, squashed spi pinconf/mux,
added emd1's gmac0 config,fix dtc warnings]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This adds the missing assignment of DEFAULT_SOC to the SOC variable
by default.
Fixes: 09ee51c614 ("lantiq: define SOC only once for uniform targets")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
In lantiq there are several subtarget where all devices have the
same value set to the SOC variable for each device individually.
This patch introduces a non-device-dependent variable DEFAULT_SOC,
which is used if no specific SOC is set for a device, and thus reduces
the number of redundant definitions drastically.
This is applied to all subtargets except xway, as only the latter has
two different SOCs.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The DTS_DIR variable is not a device variable, thus it should not
be set inside Device/Default but globally.
Fixes: c640370939 ("lantiq: use soc_vendor_device scheme on DTS file")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The number 3 was accidentally removed from the name during split
of DEVICE_TITLE.
Fixes: fd66687058 ("lantiq: split up DEVICE_TITLE")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
In ramips, all devices in mt7621, mt76x8 and rt288x subtarget have
the same value set to the SOC variable for each device individually.
This patch introduces a non-device-dependent variable DEFAULT_SOC,
which is used if no specific SOC is set for a device, and thus reduces
the number of redundant definitions drastically.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Based on a script for comparison, this fixes (hopefully) all errors
in SUPPORTED_DEVICES for ar71xx->ath79 upgrade.
Devices where old string is removed as the device does not exist
in ar71xx:
- dlink_dir-859-a1
- tplink_archer-a7-v5
- tplink_cpe510-v3
Devices where string is changed because it did not match the board
name in ar71xx:
- tplink_tl-mr3220-v1
- tplink_tl-mr3420-v1
- tplink_tl-wr2543-v1
- tplink_tl-wr741nd-v4
- tplink_tl-wr841-v7
- ubnt_unifiac-mesh
- ubnt_unifiac-mesh-pro
- ubnt_unifiac-pro
For this device, the correct string could not be found, but we could
not determine the correct one. Thus, the string is removed for now:
- tplink_tl-wr740n-v4
The script for checking this is quite simple (note that newer
entries, i.e. ath79->ath79 upgrade, are displayed as missing):
newpath=target/linux/ath79/image/
oldpath=target/linux/ar71xx/base-files/lib/ar71xx.sh
for s in $(grep -roh "SUPPORTED_DEVICES.*" $newpath | sed 's/SUPPORTED_DEVICES *.= *//'); do
found="Missing"
grep -q -r "\"$s\"" $oldpath && found="Found"
echo "$s: $found."
done
The errors might be filtered by appending 'grep "Missing"' to the script.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
In certain cases, the uncompressed initramfs image will overwrite
the lzma-loader, which is currently only 10 MB away from kernel image
start. To prevent this, change LZMA_TEXT_START to 24 MB, so loader
and compressed image have 8 MB at the end of RAM and uncompressed
image has 24 MB available.
This is only enabled for ath79 at the moment, as there we can be sure
that all devices have 32+ MB RAM and TARGET_INITRAMFS_COMPRESSION_LZMA
is not enabled there.
Despite, since lzma-loader is currently build specifically for ath79
anyway, there is no need to re-specify LOADADDR and LZMA_TEXT_START
in image/Makefile, so the values are set directly in
image/lzma-loader/Makefile and the overwrite in image/Makefile is
removed.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
This commit adds support for the MikroTik RouterBOARD wAP G-5HacT2HnD
(wAP AC), a small weatherproof dual band, dual-radio 802.11ac
wireless AP with integrated omnidirectional anntennae and one
10/100/1000 Mbps Ethernet port.
See https://mikrotik.com/product/RBwAPG-5HacT2HnD for more info.
Specifications:
- SoC: Qualcomm Atheros QCA9556
- RAM: 64 MB
- Storage: 16 MB NOR
- Wireless:
· Atheros AR9550 (SoC) 802.11b/g/n 2x2:2, 2 dBi antennae
· Qualcomm QCA9880 802.11a/n/ac 3x3:3, 2 dBi antennae
- Ethernet: Atheros AG71xx (SoC, AR8033), 1x 1000/100/10 port,
passive PoE in
Working:
- Board/system detection
- Sysupgrade
- Serial console
- Ethernet
- 2.4 GHz radio
- 5 GHz radio and LED
- Reset button
Not working/Unsupported:
- 2.4 GHz LED
- AP/CAP LED
- ZT2046Q SPI temperature and voltage sensor
This adds the basic features for supporting MikroTik devices:
- a common recipe for mikrotik images in common-mikrotik.mk
- support for minor (MikroTik NOR) split firmware (only for
generic subtarget so far)
Acknowledgments: Robert Marko <robimarko@gmail.com>
Andrew Cameron <apcameron@softhome.net>
Koen Vandeputte <koen.vandeputte@ncentric.com>
Chuanhong Guo <gch981213@gmail.com>
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
Co-developed-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
In order to make the QCA955x SGMII workaround work, the unsuccessful
SGMII autonegotiation on the AR8033 should not block the PHY
state-machine.
Otherwise, the ag71xx driver never becomes aware of the copper-side
link-establishment and the workaround is never executed.
Signed-off-by: David Bauer <mail@david-bauer.net>
[remove one trailing whitespace per file]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This commit adds a workaround for the loss of the SGMII link observed on
the QCA955x generation of SoCs. The workaround originates part from the
U-Boot source code, part from the implementation from AVM found in the
GPL tarball for the AVM FRITZ!WLAN Repeater 450E.
The bug results in a stuck SGMII link between the PHY device and the SoC
side. This has only been observed with the Atheros AR8033 PHY and most
likely all devices using such combination are affected.
It is worked around by reading a hidden SGMII status register and
issuing a SGMII PHY reset until the link becomes useable again.
Signed-off-by: David Bauer <mail@david-bauer.net>
Due to the history of the target, all devices added before a certain
point have the same device string in BOARD_NAME, DEVICE_DTS and added
to SUPPORTED_DEVICES.
Thus, we can set this one automatically for all devices where
BOARD_NAME is specified, removing the explicit DEVICE_DTS and
SUPPORTED_DEVICES addition there.
For new devices, nothing has changed, and just DEVICE_DTS has to
be set manually.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This tidies up the image Makefiles for the sunxi target by:
- Move the if-condition for the subtarget to the parent Makefile
- Remove lots of unnecessary empty lines
- Sort device definitions alphabetically
- Harmonize line wrapping for DEVICE_PACKAGES
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Change u-boot-env partitions to be mounted as read-write for gl-ar150,
gl-domino and gl-mifi so uboot-envtools support is possible.
Signed-off-by: Kimmo Vuorinen <kimmo.vuorinen@gmail.com>
[commit title/message facelift]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
TP-Link TL-WA850RE v2 is a wall-plug N300 Wi-Fi range extender,
based on Qualcomm/Atheros QCA9533 v2.
Short specification:
- 550/391/195 MHz (CPU/DDR/AHB)
- 1x 10/100 Mbps Ethernet
- 32 MB of RAM (DDR1)
- 4 MB of FLASH
- 2T2R 2.4 GHz
- 2x internal antennas (embedded on PCB)
- 9x LED (all can be turned off with GPIO15), 2x button
- UART (J3) header on PCB
Flash instruction: use "factory" image directly in vendor GUI.
Warning: this device does not include any kind of recovery mechanism
in the bootloader and disassembling process is not trivial.
You can access vendor firmware over serial line using:
- login: root
- password: sohoadmin
Stock firmware uses label MAC address for WiFi and same with local
bit set for ethernet. Since this is difficult to reproduce with
the toolset of OpenWrt, we just keep both ethernet and WiFi to
the same address here.
This is the first tiny device with tplink-safeloader in ath79.
Firmware partition is only 3648k and thus even smaller than for
the tplink-4m(lzma) devices.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This moves the TP-Link TL-WA850RE v2 to dynamic partitioning and
will allow to use this for ath79 as well.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
- Remove the "RGMII TX delay fixup" hack and the associated
DT-property. It was never used in a DT-based platform and
solved a problem which can be mitigated by using correct
delays on the MAC side.
- Remove the patch to enable platform-data support for the
at803x driver. It was only used by ar71xx which does not
(and never will) support kernel 4.19 or later.
- Remove the SmartEEE DT-configuration patch. As explained
previously, this patch never disabled the Atheros SmartEEE
implementation, but rather "standard" EEE. This can be done
on device-tree compatible platforms by adding the
"eee-broken-1000t" or "eee-broken-100tx" properties to the PHY
node. As all usages of the old properties are migrated, this
patch can be removed.
Signed-off-by: David Bauer <mail@david-bauer.net>
Acked-by: Christian Lamparter <chunkeey@gmail.com>
The hack-patch which introduced the "at803x-disable-smarteee" for
disabling SmartEEE did in fact not disable SmartEEE but rather disabled
802.3az "standard" EEE.
This can be done by using the upstream properties "eee-broken-100tx" and
"eee-broken-1000t". EEE is then disabled by the PHY subsystem.
Tested on devolo WiFi pro 1200e.
Signed-off-by: David Bauer <mail@david-bauer.net>
This ports support for the TL-WA850RE v1 range extender from ar71xx
to ath79.
Specifications:
Board: AP123 / AR9341 rev. 3
Flash/RAM: 4/32 MiB
CPU: 535 MHz
WiFi: 2.4 GHz b/g/n
Ethernet: 1 port (100M)
Flashing instructions:
Upload the factory image via the vendor firmware upgrade option.
Recovery:
Note that this device does not provide TFTP via ethernet like many
other TP-Link devices do. You will have to open the case if you
require recovery beyond failsafe.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Add patches retrying to probe the PHY to restore support for PHYs taking
longer to initialize without breaking modules without PHYs.
Patches taken from http://git.armlinux.org.uk/cgit/linux-arm.git/log/?h=phy
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Update the uDPU kernel support, fixing a number of issues:
* make ethernet work again by adding comphy definitions
* slow the I2C bus to give it more chance of actually working
* the SFP cages are designed to support up to 3W modules, which
would be prevented from initialising without this patch.
Signed-off-by: Russell King <linux@armlinux.org.uk>
[jonas.gorski: rename to mvebu, refresh patches]
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Add support for Methode DM7052 NBASE-T module to OpenWRT. These
patches are taken from my "phy" branch, and will be sent for the
next kernel merge window.
Signed-off-by: Russell King <linux@armlinux.org.uk>
[jonas.gorski: move patches to pending, refresh patches]
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Backport the phy/phylink/sfp patches currently queued in netdev or in
mainline necessary to support GPON popular modules, specifically to
support Huawei and Nokia GPON modules.
Signed-off-by: Russell King <linux@armlinux.org.uk>
[jonas.gorski: include kernel version in file names, refresh patches]
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Move two phylink patches from mvebu to generic, so that everyone can
benefit from them.
Signed-off-by: Russell King <linux@armlinux.org.uk>
[jonas.gorski: add kernel version to file names]
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Remove the old phylink/SFP patches from the OpenWRT build; these will
be updated with a new set in subsequent.
450-reprobe_sfp_phy is also removed for several reasons:
1) it is not in mainline.
2) it breaks copper modules that do not have a PHY.
3) it makes backporting the current patch set harder.
Discussion is ongoing with the patch author for a mainline Linux kernel
patch for this.
Signed-off-by: Russell King <linux@armlinux.org.uk>
TPLINK_BOARD_NAME has been renamed to TPLINK_BOARD_ID a long time
ago (7d6c63d875: "build: rename TPLINK_BOARD_NAME to
TPLINK_BOARD_ID" for ar71xx), and before introducing ath79 target
at all.
TPLINK_BOARD_NAME seems to have been introduced into ath79 target
only by mistake. It has never been used. Remove it.
Fixes: 53c474abbd ("ath79: add new OF only target for QCA MIPS silicon")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This reverts commit de80424f70 which needs
more work and testing as it broke at least jffs2 overlays at least on
ath79 platform, marking them as read-only, thus unusable:
jffs2_build_filesystem(): erasing all blocks after the end marker...
jffs2: Erase at 0x009e0000 failed immediately: -EROFS. Is the sector locked?
Ref: http://lists.infradead.org/pipermail/openwrt-devel/2020-January/021344.html
Reported-by: Steve Brown <sbrown@ewol.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
In zynq target, the DEVICE_DTS variable is always set consistent
with the model part of the device definition name.
This patch replaces the redundant definitions for the individual
devices with a common recipe.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
For the mvebu target in particular, there is a lot of files in
base-files that are only relevant for one subtarget. Improve
overview and reduce size per subtarget by moving/splitting
base-files depending on the subtarget they belong to.
While at it, consolidate 01_leds by using the model part of
the board name as variable.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Acked-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
This introduces the SOC variable to mvebu target to derive some of
the DEVICE_DTS variables based on the SOC prefix and the device
definition name.
Since DTS names and compatible are inconsistent also in the kernel
for this target, the scheme cannot be applied to all devices, though.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Acked-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
This moves the if conditions for choosing which image Makefiles
are used to the parent image/Makefile. It seems more convenient
to have "codeflow" in the parent while the subtarget-specific
files only contain the definitions.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Acked-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
This device is an LTE router supported in ar71xx so far.
As per original commit, hardware specifications (v1.0 EU):
- SoC: QCA9531
- Flash: Winbond W25Q64FV (8MiB)
- RAM: EtronTech EM6AB160TSE-5G (64MiB)
- Wireless: SoC platform only (2.4GHz b/g/n, 2x internal antenna)
- Ethernet: 2NIC (3x100M + 1x100M)
- WWAN: TP-LINK LTE MODULE (2x external detachable antenna)
- Power: DC 12V 1A
Flashing instructions:
You can flash via tftp recovery (serve factory image as /mr6400_tp_recovery.bin
on 192.168.0.66/24, connect to any ethernet port and power on device while
holding the reset button). Flashing via OEM web interface does not work.
Known issues:
- LTE module does not always come up during boot (showing USB enumeration errors). Similar behavior has been reported at least from one user for ar71xx, too. Turning USB off and on again will serve as a workaround.
- eth0 (LAN) always shows carrier as 1 even if no cable is plugged in (this works "correctly" on ar71xx)
Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
[several adjustments]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: Filip Moc <lede@moc6.cz>
When mapping for RSSI LEDs was defined for interface wlan0 on
Ubiquiti Rocket M Titanium, it missed connection to actual interface.
Therefore create the mapping to interface, so RSSI LEDs work without
additional configuration, after starting rssileds service.
While at that, split RSSI into ~equal intervals for 6 LEDs,
and remove coefficients needed for PWM LEDs, as this board does not
support PWM LEDs.
Finally, for complete support, enable 'rssileds' package in per-device
rootfs, so the indicator works out of box.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Kernel partition increase to 4 MiBs for Netgear WNDR3700v4 and WNDR4300
routers breaks sysupgrade image compatibility with ar71xx builds.
Therefore, SUPPORTED_DEVICES variable has to be removed for both devices
from target makefile.
Reported-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
Currently it's not possible to effectively mark a "firmware" partition
as read-only. The sub-partitions "kernel", "rootfs" and "rootfs_data"
are always created as read-write (ignoring the parent access mode).
This patch enforces the access mode of sub-partitions to match the
parent partition, which is useful for recovery images that are meant
to be fully read-only to avoid accidental damage from end-user.
An example of such implementation (read-only firmware image) is the
recovery image used on the Zsun-SD100 [1].
Please note the related patch for fstools [2] to enable this read-only
concept.
[1] https://github.com/brunompena/zsun-resources
[2] http://lists.infradead.org/pipermail/openwrt-devel/2020-January/021043.html
Signed-off-by: Bruno Pena <brunompena@gmail.com>
[removed already obsolete 4.9 kernel patch]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
