Based on Paul Fertser <fercerpav@gmail.com>'s guidance:
Change AUTORELEASE in rules.mk to:
```
AUTORELEASE = $(if $(DUMP),0,$(shell sed -i "s/\$$(AUTORELEASE)/$(call commitcount,1)/" $(CURDIR)/Makefile))
```
then update all affected packages by:
```
for i in $(git grep -l PKG_RELEASE:=.*AUTORELEASE | sed 's^.*/\([^/]*\)/Makefile^\1^';);
do
make package/$i/clean
done
```
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
In the version 2023.01, the U-boot image was renamed because of the
upstream change [1]
[1] 87ac4b4b4c
Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
Add support for building for Methode eDPU board, no patches are needed
as board has been upstreamed and is part of the 2022.10-rc releases.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Update mvebu U-boot to 2022.10 to avoid backporting patches in order
to support Methode eDPU.
It also allows dropping existing patches as they are all backports.
Tested-by: Andre Heider <a.heider@gmail.com> # espressobin-v3-v5-1gb-2cs
Tested-by: Russell Morris <github@rkmorris.us> # espressobin-v3-v5-1gb-1cs
Tested-by: Josef Schlehofer <pepe.schlehofer@gmail.com> [Turris Omnia]
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
If you would like to compile the newest version of U-boot together with the stable
OpenWrt version, which does not have LibreSSL >= 3.5, which was updated
in the master branch by commit 5451b03b7c
("tools/libressl: bump to v3.5.3"), then you need these two patches to
fix it. They are backported from U-boot repository.
This should be backported to stable OpenWrt versions.
Reported-by: Michal Vasilek <michal.vasilek@nic.cz>
Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
This issue was reported by @paper42, who is using Void Linux with musl
to compile OpenWrt and its packages and found out it is not possible to
compile U-boot for Turris Omnia (neither any other).
It fixes following output:
```
HOSTCC tools/kwboot
tools/kwboot.c: In function 'kwboot_tty_change_baudrate':
tools/kwboot.c:662:6: error: 'struct termios' has no member named 'c_ospeed'
662 | tio.c_ospeed = tio.c_ispeed = baudrate;
| ^
tools/kwboot.c:662:21: error: 'struct termios' has no member named 'c_ispeed'
662 | tio.c_ospeed = tio.c_ispeed = baudrate;
| ^
tools/kwboot.c:690:31: error: 'struct termios' has no member named 'c_ospeed'
690 | if (!_is_within_tolerance(tio.c_ospeed, baudrate, 3))
| ^
tools/kwboot.c:693:31: error: 'struct termios' has no member named 'c_ispeed'
693 | if (!_is_within_tolerance(tio.c_ispeed, baudrate, 3))
|
```
Tested-by: Michal Vasilek <michal.vasilek@nic.cz>
Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
We don't need to make sure that we want to have enabled
CONFIG_CMD_SETEXPR by default, since this is already done in U-boot [1].
This was actually needed only for clearfog board [2], which was added in
commit: da0005a6d08ae33d958a6d8a6c0c12dc07b5b2b8 ("uboot-mvebu: add
patch to enable setexpr for clearfog boards) and send to U-boot to fix
it properly. After a while, there was added support for Turris Omnia,
which uses setexpr as well [3], but for this board, there are no fixes
needed in U-boot and that's why we can remove this option here.
It is helpful with shell scripting. If some downstream distributions are
using it, they should correct it in defconfig for related boards.
[1] e95afa5675/cmd/Kconfig (L1504)
[2] 852126680e/target/linux/mvebu/image/clearfog.bootscript (L7)
[3] 852126680e/target/linux/mvebu/image/turris-omnia.bootscript (L2)
Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
Option CMD_SETEXPR is already default in U-boot [1], since this was
disabled since initial version for this board, there is send this
patch to U-boot mailing list to enable it.
It is required to use in OpenWrt bootscript for these boards [2].
[1] e95afa5675/cmd/Kconfig (L1504)
[2] 852126680e/target/linux/mvebu/image/clearfog.bootscript (L7)
Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
v2022.01 has a regression that broke eMMC usage on most if not all Armada
SoC-s, thus breaking boards like uDPU which use eMMC for storage.
Fix it by backporting a recent upstream patch.
Fixes: 782d4c8306 ("uboot-mvebu: update to version 2022.01")
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Steps to reproduce:
1. Insert NVMe disk with a reduction to Turris Omnia
2. Go to U-boot
3. Run these two commands:
a) ``nvme scan``
b) ``nvme detail``
4. Wait for crash
This is backported from U-boot upstream repository.
It should be included in the upcoming release - 2022.04 [1].
It was tested on Turris Omnia, mvebu, cortex-a9, OpenWrt master.
[1] https://patchwork.ozlabs.org/project/uboot/patch/20211209100639.21530-1-pali@kernel.org/
Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
[Export the patch from U-Boot git]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
100-ddr-marvell-a38x-fix-BYTE_HOMOGENEOUS_SPLIT_OUT-deci.patch [1]:
SoC Marvell A38x is used in Turris Omnia, and we thought that with recent
fiddling around DDR training to fix it once for all, there were
reproduced the issue in the upcoming new revision Turris Omnia boards.
101-arm-mvebu-spl-Add-option-to-reset-the-board-on-DDR-t.patch [2]:
This is useful when some board may occasionally fail with DDR training,
and it adds the option to reset the board on the DDR training failure
102-arm-mvebu-turris_omnia-Reset-the-board-immediately-o.patch [3]:
This enables the option CONFIG_DDR_RESET_ON_TRAINING_FAILURE (added by
101 patch), so the Turris Omnia board is restarted immediately, and it
does not require to reset the board manually or wait 120s for MCU to
reset the board
[1] https://patchwork.ozlabs.org/project/uboot/patch/20220217000837.13003-1-kabel@kernel.org/
[2] https://patchwork.ozlabs.org/project/uboot/patch/20220217000849.13028-1-kabel@kernel.org/
[3] https://patchwork.ozlabs.org/project/uboot/patch/20220217000849.13028-2-kabel@kernel.org/
Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
This solves issue with DDR training on Turris Omnia.
Log:
******** DRAM initialization Failed (res 0x1) ********
DDR3 Training Sequence - FAILED
ERROR ### Please RESET the board ###
Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
Host libraries are only build static, so let's pass --static to
pkg-config globally and remove the then unnecessary patches doing
exactly that individually.
Signed-off-by: Andre Heider <a.heider@gmail.com>
Using Host/Exports doesn't work as intended, explicitly add the
required vars so that u-boot finds the required libraries when building
its tools.
Signed-off-by: Andre Heider <a.heider@gmail.com>
u-boot binaries are not useful for these boards, they need to be combined
with atf for a proper firmware.
Signed-off-by: Andre Heider <a.heider@gmail.com>
u-boot binaries for this SoC are only required for the atf package,
disable them per default so they don't get build unnecessarily.
Signed-off-by: Andre Heider <a.heider@gmail.com>
Certain SFP modules (most notably Nokia GPON ones) first check
connectivity on 1000base-x, and switch to 2500base-x afterwards. This
is considered a quirk so the phylink switches the interface to
2500base-x as well.
However, after power-cycling the uDPU device, network interface/SFP module
will not work correctly until the module is re-seated. This patch
resolves this issue by forcing the interface to be brought up in
2500base-x mode by default.
Signed-off-by: Jakov Petrina <jakov.petrina@sartura.hr>
Signed-off-by: Vladimir Vid <vladimir.vid@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
The BUILD_VARIANT might differ from UBOOT_CONFIG, so point to a file we
are actually changing. Being here let's call 'Build/Configure/U-Boot'
definition, instead of definig the same command. This'll be more future
proof, if U-Boot configuration procedure will change.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
* add u-boot support for uDPU
* add line to copy u-boot binary to STAGING_DIR_IMAGE, this can later be used
as BL33 variable required for ATF build
* add patch to increase max gunzip size in mvebu_armada-37xx.h which is
required for booting the itb recovery images
Signed-off-by: Vladimir Vid <vladimir.vid@sartura.hr>
Some devices and packages require newer version of u-boot to work
properly, update u-boot to keep up with 4.19 kernel.
Signed-off-by: Vladimir Vid <vladimir.vid@sartura.hr>
[re-added missing commit message]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Add vendors in device names and also rename few device names, for easier
identyfying potential firmware to flash. The vendor and device string is
mainly derived from model/compatipble string in dts from particular
device, but since not all devices are well described, some of the renames
follow marketing names.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
The uboot-mvebu package incorrectly used the host pkg-config for the tool
build parts, which broke the build on systems lacking pkg-config and only
worked by accident on those that have it installed.
Export the host-build specific environment variables for the uboot build
to redirect pkg-config invocations to our staged host build pkg-config in
buildroot.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
When libressl was linked the libpthread was missing, add it in addition.
Fixes: 2c192b6916 ("tools/libressl: update to version 2.7.2")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This release brings various improvements to clearfog support, such as distro-boot.
Obsoletes:
0002-clearfog-reset-usom-onboard-1512-phy.patch
0003-clearfog-enable-distro-boot-code.patch
Signed-off-by: Josua Mayer <josua.mayer97@gmail.com>
CONFIG_* variables can easily be set by overriding Build/Configure.
so set NET_RANDOM_ETHADDR=y and CMD_SETEXPR=y here.
This replaces the following patches:
0001-clearfog-generate-random-MAC-address.patch
0004-clearfog-enable-setexpr-command-by-default.patch
Signed-off-by: Josua Mayer <josua.mayer97@gmail.com>
Since I have no openssl-dev on my machine, I first
get this error:
```
tools/kwbimage.c:21:10: fatal error: openssl/bn.h: No such file or directory
#include <openssl/bn.h>
```
After removing the UBOOT_MAKE_FLAGS the next error is:
```
tools/kwbimage.c:40:6: error: conflicting types for ‘EVP_MD_CTX_cleanup’
void EVP_MD_CTX_cleanup(EVP_MD_CTX *ctx)
```
After removing the OpenSSL patches the next error is:
```
HOSTLD tools/dumpimage
/usr/bin/ld: cannot find -lssl
/usr/bin/ld: cannot find -lcrypto
collect2: error: ld returned 1 exit status
scripts/Makefile.host:108: recipe for target 'tools/dumpimage' failed
make[5]: *** [tools/dumpimage] Error 1
```
So, the final part is to add the build system's
HOST_LDFLAGS to the UBOOT_MAKE_FLAGS.
(which was done in the previous commit)
Then the image builds.
Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
Fixes the following build issue: "undefined reference to `EVP_MD_CTX_create'"
From: Jelle van der Waa <jelle@vdwaa.nl>
The rsa_st struct has been made opaque in 1.1.x, add forward compatible
code to access the n, e, d members of rsa_struct.
EVP_MD_CTX_cleanup has been removed in 1.1.x and EVP_MD_CTX_reset should be
called to reinitialise an already created structure.
Signed-off-by: Marko Ratkaj <marko.ratkaj@sartura.hr>
Add a patchfile that implements distro-boot and is meant to go upstream
Also make the other patches git-am'able for easier maintenance.
Signed-off-by: Josua Mayer <josua.mayer97@gmail.com>
Add support for SolidRun ClearFog Base board.
The base model is a smaller version of ClearFog Pro without
the DSA switch, replacing it with a second copper gigabit
port, and only one PCIe socket.
Signed-off-by: Marko Ratkaj <marko.ratkaj@sartura.hr>
Do not put the u-boot images into the kernel build directory as this directory
might get removed after kernel updates while the u-boot packages InstallDev
recipe is not getting re-executed because it is still considered current,
leading to image build failures later on due to missing u-boot images.
To ensure that built bootloader images persist over kernel version updates in
the buildroot, put them into the new STAGING_DIR_IMAGE directory.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
