Build the amd64-microcode package on all architectures even if it only
makes sense to use it on x86. If the package build is done by a builder
not building for x86 it will not include the package otherwise.
Link: https://github.com/openwrt/openwrt/pull/16031
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Mark the package as nonshared to build it in the target specific build
step 1 of the build bots instead of the architecture generic build step
2. In the build step 2 it may be left out if we build it using a
different target.
Fixes: 24d6abe2d7 ("firmware-utils: new package replacing otrx")
Link: https://github.com/openwrt/openwrt/pull/16031
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Mark the package as nonshared to build it in the target specific build
step 1 of the build bots instead of the architecture generic build step
2. In the build step 2 it may be left out if we build it using a
different target.
Fixes: 8619d7af67 ("kirkwood: add D-Link DNS-320L support")
Link: https://github.com/openwrt/openwrt/pull/16031
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Mark the package as nonshared to build it in the target specific build
step 1 of the build bots instead of the architecture generic build step
2. In the build step 2 it may be left out if we build it using a
different target.
Fixes: 1eb21b87bd ("kobs-ng: add new package")
Link: https://github.com/openwrt/openwrt/pull/16031
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Mark the package as nonshared to build it in the target specific build
step 1 of the build bots instead of the architecture generic build step
2. In the build step 2 it may be left out if we build it using a
different target.
Fixes: 07043a853a ("imx23: rename imx23 to mxs for upcoming imx23/28 support")
Link: https://github.com/openwrt/openwrt/pull/16031
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Package the firmware files in the target specific build step and not in
the architecture common step. The architecture common step is not
necessary build for the ipq40xx target. If it is build for a different
target these packages are not packaged at all. This moves the build to
the ipq40xx target specific build step. This change is needed to make
the firmware files show up in the buildbot images.
Fixes: 02db8a19cb ("firmware: add Intel/Lantiq VRX518 ACA firmware package")
Fixes: 07b0e6f3d9 ("firmware: add Intel/Lantiq VRX518 PPE firmware package")
Fixes: 13eb1f564a ("firmware: add Intel/Lantiq VRX518 DSL firmware package")
Link: https://github.com/openwrt/openwrt/pull/16031
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Radxa ROCK Pi E v3.0 is a compact networking SBC[1] using the Rockchip
RK3328 SoC.
Hardware
--------
- Rockchip RK3328 SoC
- Quad A53 CPU
- 512MB/1GB/2GB DDR4 RAM
- 4/8/16/32GB eMMC
- Micro SD Card slot
- WiFi 4 and BT 4, or WiFi 5 and BT 5 (not supported yet)
- 1x 1000M Ethernet with PoE support (additional PoE HAT required)
- 1x 100M Ethernet
- 1x USB 3.0 Type-A port (Host)
- 1x 4-ring 3.5mm headphone jack
- 40 Pin GPIO header
[1] https://radxa.com/products/rockpi/pie
Installation
------------
Uncompress the OpenWrt sysupgrade and write it to a micro SD card or
internal eMMC using dd.
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Link: https://github.com/openwrt/openwrt/pull/15984
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The file contains the the /usr/lib path from the toolchain directory and
not from the target directory. The /usr/lib directory for the toolchain
is empty and the shared library is not in the specified paths. On RISCV
the linker of util-linux was finding the libncursesw.so in my host
system, tried to link against it and failed. Fix the .pc file.
Fixes: #15942
Co-authored-by: Thomas Weißschuh <thomas@t-8ch.de>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Link: https://github.com/openwrt/openwrt/pull/16018
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add support for NEC Aterm series devices based on Atheros AR9344.
The following devices have almost the same hardware, so the same U-Boot
binary can be used for them.
- NEC Aterm WR8750N
- NEC Aterm WR9500N
- NEC Aterm WG600HP
By the way, on NetBSD-based NEC Aterm devices, only 0x20000 (128KiB) is
available for a bootloader on the flash chip and that limitation is too
small for mainline U-Boot with the default options. So many
features/commands not required for booting OpenWrt and recoverying are
disabled on that devices, like the followings.
- networking support
- FIT support
- all decompression methods support
etc...
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15432
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add U-Boot package for the devices that based on Atheros/Qualcomm
Atheros SoCs.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15432
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
By default nand_do_upgrade() can only deal with raw and gzipped firmware
files. Vendors often use custom firmware containers. Allow passing
custom extraction command to allow using nand_do_upgrade() with vendor
firmwares.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Same as TP-Link TL-XDR608x, this router comes with locked vendor
loader. Add U-Boot build for replacement loader for this device.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/15930
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Radxa ROCK Pi S is a small in size, full in features SBC[1] using the
Rockchip RK3308B SoC.
Hardware
--------
- Rockchip RK3308B SoC
- Quad A35 CPU
- 256/512MB DDR3 RAM
- Optional 4/8GB eMMC
- Micro SD Card slot
- Optional WiFi 4 and BT 4 (not supported yet)
- 1x 100M Ethernet with PoE support (additional PoE HAT required)
- 1x USB 2.0 Type-A port (Host)
- 1x USB 2.0 Type-C port (OTG)
- 2x 26 Pin GPIO header
[1] https://radxa.com/products/rockpi/pis
Installation
------------
Uncompress the OpenWrt sysupgrade and write it to a micro SD card or
internal eMMC using dd.
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Link: https://github.com/openwrt/openwrt/pull/15933
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This is required by the DSL CPE API driver.
Signed-off-by: Martin Schiller <ms.3headeddevs@gmail.com>
[update for new license]
Signed-off-by: Andre Heider <a.heider@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15550
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This firmware is used by the vrx518 tc driver.
Signed-off-by: Martin Schiller <ms.3headeddevs@gmail.com>
[update for new license]
Signed-off-by: Andre Heider <a.heider@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15550
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This firmware is used by the vrx518 ep driver.
Signed-off-by: Martin Schiller <ms.3headeddevs@gmail.com>
[update for new license]
Signed-off-by: Andre Heider <a.heider@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15550
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add the package for the Pixart PAC7302 USB Camera Driver kernel module.
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15886
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
If we're being paranoid and quote all the arguments to ipcalc.sh,
it's possible to pass in empty start and range arguments. This
should be handled the same as their being absent.
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
Link: https://github.com/openwrt/openwrt/pull/15946
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Huawei AP6010DN is a dual-band, dual-radio 802.11a/b/g/n 2x2 MIMO
enterprise access point with one Gigabit Ethernet port and PoE
support.
Hardware highlights:
- CPU: AR9344 SoC at 480MHz
- RAM: 128MB DDR2
- Flash: 32MB SPI-NOR
- Wi-Fi 2.4GHz: AR9344-internal radio
- Wi-Fi 5GHz: AR9580 PCIe WLAN SoC
- Ethernet: 10/100/1000 Mbps Ethernet through Atheros AR8035 PHY
- PoE: yes
- Standalone 12V/2A power input
- Serial console externally available through RJ45 port
- External watchdog: CAT706SVI (1.6s timeout)
Serial console:
9600n8 (9600 baud, no stop bits, no parity, 8 data bits)
MAC addresses:
Each device has 32 consecutive MAC addresses allocated by
the vendor, which don't overlap between devices.
This was confirmed with multiple devices with consecutive
serial numbers.
The MAC address range starts with the address on the label.
To be able to distinguish between the interfaces,
the following MAC address scheme is used:
- eth0 = label MAC
- radio0 (Wi-Fi 2.4GHz) = label MAC + 1
- radio1 (Wi-Fi 5GHz) = label MAC + 2
Installation:
0. Connect some sort of RJ45-to-USB adapter to "Console" port of the AP
1. Power up the AP
2. At prompt "Press f or F to stop Auto-Boot in 3 seconds",
do what they say.
Log in with default admin password "admin@huawei.com".
3. Boot the OpenWrt initramfs from TFTP using the hidden script "run ramboot".
Replace IP address as needed:
> setenv serverip 192.168.1.10
> setenv ipaddr 192.168.1.1
> setenv rambootfile openwrt-ath79-generic-huawei_ap6010dn-initramfs-kernel.bin
> saveenv
> run ramboot
4. Optional but recommended as the factory firmware cannot be downloaded publicly:
Back up contents of "firmware" partition using the web interface or ssh:
$ ssh root@192.168.1.1 cat /dev/mtd11 > huawei_ap6010dn_fw_backup.bin
5. Run sysupgrade using sysupgrade image. OpenWrt
shall boot from flash afterwards.
Return to factory firmware (using firmware upgrade package downloaded from non-public Huawei website):
1. Start a TFTP server in the directory where
the firmware upgrade package is located
2. Boot to u-boot as described above
3. Install firmware upgrade package and format the config partitions:
> update system FatAP6X10XN_SOMEVERSION.bin
> format_fs
Return to factory firmware (from previously created backup):
1. Copy over the firmware partition backup to /tmp,
for example using scp
2. Use sysupgrade with force to restore the backup:
sysupgrade -F huawei_ap6010dn_fw_backup.bin
3. Boot AP to U-Boot as described above
Quirks and known issues:
- The stock firmware has a semi dual boot concept where the primary
kernel uses a squashfs as root partition and the secondary kernel uses
an initramfs. This dual boot concept is circumvented on purpose to gain
more flash space and since the stock firmware's flash layout isn't
compatible with mtdsplit.
- The external watchdog's timeout of 1.6s is very hard to satisfy
during bootup. This is why the GPIO15 pin connected to the watchdog input
is configured directly in the LZMA loader to output the AHB_CLK/2 signal
which keeps the watchdog happy until the wdt-gpio kernel driver takes
over. Because it would also take too long to read the whole kernel image
from flash, the uImage header only includes the loader which then reads
the kernel image from flash after GPIO15 is configured.
Signed-off-by: Marco von Rosenberg <marcovr@selfnet.de>
Link: https://github.com/openwrt/openwrt/pull/15941
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hardware specification:
SoC: MediaTek MT7981B 2x A53
Flash: 128 MB SPI-NAND
RAM: 256MB
Ethernet: 4x 10/100/1000 Mbps
Switch: MediaTek MT7531AE
WiFi: MediaTek MT7976C
Button: Reset, Mesh
Power: DC 12V 1A
Gain telnet access:
1. Login into web interface, and download the configuration.
2. Decode and uncompress the configuration:
* Enter fakeroot if you are not login as root.
base64 -d e-xxxxxxxxxxxx-cfg.tar.gz | tar -zx
3. Edit 'etc/passwd', remove root password: 'root::1:0:99999:7:::'.
4. Edit 'etc/rc.local', insert telnetd command before 'exit 0':
( sleep 3s; /usr/sbin/telnetd; ) &
5. Repack the configuration:
tar -zc etc/ | base64 > e-xxxxxxxxxxxx-cfg.tar.gz
6. Upload new configuration via web interface, now you can connect to
ASR3000 via telnet.
Flash instructions:
1. Connect to ASR3000, backup everything, especially 'Factory' part.
2. Write new BL2:
mtd write openwrt-mediatek-filogic-abt_asr3000-preloader.bin BL2
3. Write new FIP:
mtd write openwrt-mediatek-filogic-abt_asr3000-bl31-uboot.fip FIP
4. Set static IP on your PC:
IP 192.168.1.254/24, GW 192.168.1.1
5. Serve OpenWrt initramfs image using TFTP server.
6. Cut off the power and re-engage, wait for TFTP recovery to complete.
7. After OpenWrt has booted, perform sysupgrade.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/15887
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This patch cleans up the following warnings during build:
"warning: format not a string literal"
```
conf.c: In function 'conf_askvalue':
conf.c:89:17: warning: format not a string literal and no format arguments [-Wformat-security]
89 | printf(_("(NEW) "));
| ^~~~~~
conf.c: In function 'conf_choice':
conf.c:285:33: warning: format not a string literal and no format arguments [-Wformat-security]
285 | printf(_(" (NEW)"));
| ^~~~~~
conf.c: In function 'check_conf':
conf.c:440:41: warning: format not a string literal and no format arguments [-Wformat-security]
440 | printf(_("*\n* Restart config...\n*\n"));
| ^~~~~~
conf.c: In function 'main':
conf.c:617:41: warning: format not a string literal and no format arguments [-Wformat-security]
617 | _("\n*** The configuration requires explicit update.\n\n"));
| ^
conf.c:669:25: warning: format not a string literal and no format arguments [-Wformat-security]
669 | fprintf(stderr, _("\n*** Error during writing of the configuration.\n\n"));
| ^~~~~~~
conf.c:673:25: warning: format not a string literal and no format arguments [-Wformat-security]
673 | fprintf(stderr, _("\n*** Error during update of the configuration.\n\n"));
| ^~~~~~~
conf.c:684:25: warning: format not a string literal and no format arguments [-Wformat-security]
684 | fprintf(stderr, _("\n*** Error during writing of the configuration.\n\n"));
| ^~~~~~~
```
And POSIX Yacc warnings
```
lex -ozconf.lex.c -L zconf.l
yacc -ozconf.tab.c -t -l zconf.y
zconf.y:34.1-7: warning: POSIX Yacc does not support %expect [-Wyacc]
34 | %expect 32
| ^~~~~~~
zconf.y:97.1-11: warning: POSIX Yacc does not support %destructor [-Wyacc]
97 | %destructor {
| ^~~~~~~~~~~
gcc -Wall -Wmissing-prototypes -Wstrict-prototypes -O2 -fomit-frame-pointer -DKBUILD_NO_NLS -c -o zconf.tab.o zconf.tab.c
gcc conf.o zconf.tab.o -o conf
```
After:
gcc -Wall -Wmissing-prototypes -Wstrict-prototypes -O2 -fomit-frame-pointer -DKBUILD_NO_NLS -c -o conf.o conf.c
yacc -Wno-yacc -ozconf.tab.c -t -l zconf.y
gcc -Wall -Wmissing-prototypes -Wstrict-prototypes -O2 -fomit-frame-pointer -DKBUILD_NO_NLS -c -o zconf.tab.o zconf.tab.c
gcc conf.o zconf.tab.o -o conf
Signed-off-by: Sean Khan <datapronix@protonmail.com>
Link: https://github.com/openwrt/openwrt/pull/15953
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
NAND code uses either "cat" or "zcat" for getting firmware image
content. Code was full of duplicated ${gz}cat calls. Use "cmd" variable
that is determined by a caller and passed to lower level functions. This
avoids code duplication and allows adding support for more formats.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
The function was moved to /lib/upgrade/fit.sh which is part of the fitblk
package. Remove it from /lib/upgrade/common.sh to safe space on boards
not using unified uImage.FIT images.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Use export_fitblk_bootdev() in /lib/upgrade/fit.sh instead of now
deprecated fitblk_get_bootdev() function. Include /lib/upgrade/fit.sh
instead of /lib/upgrade/common.sh to allow removing the function there.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Move shell functions used for sysupgrade into /lib/upgrade/fit.sh.
Introduce improved fitblk boot device detection function which
works also in case ubiblock devices have not yet been created or
even UBI itself not yet being attached.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This fixes multiple security problems:
* [Medium] CVE-2024-1544
Potential ECDSA nonce side channel attack in versions of wolfSSL before 5.6.6 with wc_ecc_sign_hash calls.
* [Medium] CVE-2024-5288
A private key blinding operation, enabled by defining the macro WOLFSSL_BLIND_PRIVATE_KEY, was added to mitigate a potential row hammer attack on ECC operations.
* [Low] When parsing a provided maliciously crafted certificate directly using wolfSSL API, outside of a TLS connection, a certificate with an excessively large number of extensions could lead to a potential DoS.
* [Low] CVE-2024-5991
In the function MatchDomainName(), input param str is treated as a NULL terminated string despite being user provided and unchecked.
* [Medium] CVE-2024-5814
A malicious TLS1.2 server can force a TLS1.3 client with downgrade capability to use a ciphersuite that it did not agree to and achieve a successful connection.
* [Medium] OCSP stapling version 2 response verification bypass issue when a crafted response of length 0 is received.
* [Medium] OCSP stapling version 2 revocation bypass with a retry of a TLS connection attempt.
Unset DISABLE_NLS to prevent setting the unsupported configuration
option --disable-nls which breaks the build now.
Link: https://github.com/openwrt/openwrt/pull/15948
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
408c2cc libfstools: skip JFFS2 padding when BLOCKSIZE was given
013050f fstools: remove redundant F2FS_MINSIZE definition
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
There is no point in hard-coding the UBI volume numbers as we are
dynamically looking up the volume by volume name in all cases by now.
Remove this relict as it causes problems without being useful for
anything.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
1. Rename function _do_env_set() to env_do_env_set().
2. Replace kwbimage hack with UBOOT_CUSTOMIZE_CONFIG:
"--disable TOOLS_KWBIMAGE" and "--disable TOOLS_LIBCRYPTO".
3. Disable CONFIG_CMD_BOOTEFI_BOOTMGR for all supported devices
because the newly added UEFI bootmenu entries doesn't work.
4. Enable CONFIG_VERSION_VARIABLE for the OpenWrt One.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Co-authored-by: Daniel Golle <daniel@makrotopia.org>
73644a036f5a nl80211: move access to tb array out of uc_nl_convert_attr and below
6e3cf83a77a7 nl80211: add support for multi-attribute arrays
6ff24d5488a9 nl80211: update nl80211.h to latest wireless-next
abc2aef28641 nl80211: add wiphy multi-radio support
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Brings lots of driver updates and API changes needed for mt76 updates.
Disable iwlwifi and ath11k on 5.15, since backport is too difficult,
and the only remaining targets won't need those drivers.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
