This reverts commit 79af0593a3.
A hack adjusting fw_devlink value was added to workaround issue with
probing device drivers caused by of_platform_populate(). With upstream
mtd commit (the one adding OF_POPULATED) backported there is no need for
that hack anymore.
Ref: 3eebb91317 ("kernel: backport proper fix for mtd preventing devices probing")
Ref: #10232
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
DK01 and DK04 board support has been in a form of 2 patches that we have
been carrying for a long time.
Both of the patches contain weird changes, dont follow any DT syntax and I
honestly doubt they are even valid.
DK01 and DK04 also have not been converted to DSA even after a long time
and I doubt that anybody in the community even has these boards as they are
QCA reference boards that are not even obtainable anymore.
Since patches for these 2 boards have been just causing us pain when trying
to update the kernel to a new major release or even point releases lets
remove the support for these boards, and if there are users they can easily
be reinstated.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Teltonika RUTX currently is the only device pulling in DK01 DTSI and thus
preventing removal of DK01 and DK04 support.
So, lets add the missing nodes from DK01 DTSI and use the SoC DTSI instead.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Lets add a proper commit title and description to the SCM cold boot
patch so it applies with a git apply or git-am.
Signed-off-by: Robert Marko <robimarko@gmail.com>
SCM SDI disable support is pending upstream, so lets use that instead.
Since the board check needs to be split out, export it with a header so
it applies with git-am.
Signed-off-by: Robert Marko <robimarko@gmail.com>
This change makes it possible to use the GPIO_OPEN_DRAIN /
GPIO_OPEN_SOURCE Flags when exporting GPIOs via dts.
We need to emulate the open-source or open-drain functionalities for the
initial value, because the used functions (gpiod_direction_output_raw)
do not take this into account.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
The kernel FSL_ENETC_QOS option is only a compile time
option, it does not result in a separate module being built.
Set it to 'y' to resolve a warning from the kernel compile:
.config:2654:warning: symbol value 'm' invalid for FSL_ENETC_QOS
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Fixes: c3151b6f04 ("armvirt: 64: add support for other SystemReady-compatible vendors")
When comparing the generated OpenWrt .config to the Linux arm64
defconfig, I noticed these SATA controllers were not included.
As they may be used as a boot drive, they should be built into
the kernel.
CONFIG_SATA_MVEBU is for Marvell platforms.
CONFIG_SATA_QORIQ is for NXP Layerscape.
CONFIG_SATA_SIL24 is for Arm's Juno development board, see Linux
kernel commit d7c38ff1cd86 ("arm64: defconfig: Add Juno SATA
controller").
Signed-off-by: Mathew McBride <matt@traverse.com.au>
This MDIO driver was already being built, but not installed due
to being selected by the ThunderX Ethernet driver.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
The initial armv8 module incorrectly labelled the Thunder(v1) as
supporting the ThunderX2, when they have different drivers.
Add kmod-octeon-tx2 to support the newer devices.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
This turns on various PCI related options which are enabled
in the Linux kernel arch/arm64/configs/defconfig but not
yet in the OpenWrt config.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
These are used by common Broadcom SoC's like
the BCM2711 (RPi4) and iProc network processor.
Tested on the RPi4B using the Raspberry Pi
UEFI+ACPI firmware[1].
Signed-off-by: Mathew McBride <matt@traverse.com.au>
[1] - https://github.com/pftf/RPi4
This is part of an effort to reduce differences between
the OpenWrt armsr/armv8 config and Linux arm64 defconfig.
This enables CONFIG_ARCH_BCM and downstream
CONFIG_ARCH_BCM2835 (= BCM2711 like Raspberry Pi 4)
and CONFIG_ARCH_BCM_IPROC (Broadcom iProc packet processors).
The broadband specific SoC's (ARCH_BCMBCA) are left out
as it is assumed these will not be doing EFI boot.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Renesas markets several embedded Arm64 SoCs in the
RZ series (RZ/G, RZ/V), so should be enabled in
a general purpose target.
Automotive (R-Car) SoC's are not enabled by this change.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Due to an error on my part, Anton Antonov's
i.MX changes[1] did not fully make it into my
armvirt kernel 6.1 EFI pull request. I have updated
them using the options he supplied[1] as well
as comparing to the Linux arm64 defconfig.
The notable exception is:
CONFIG_USB_DWC3_OF_SIMPLE currently disabled
due to an issue with i.MX8P and i.MX8Q.
Fixes: 3efb3b8 ("armvirt: 64: Add NXP i.MX 8M Mini/Nano/Quad/Plus EVK support")
Signed-off-by: Mathew McBride <matt@traverse.com.au>
[1] - ccf826c344
A review of the generated OpenWrt kernel .config
vs the Linux arm64 defconfig showed that this
option was not being enabled, as it is disabled
in OpenWrt's generic config.
ACPI_BUTTON is needed to report and respond to
power button events, so it should be enabled.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
To bring the armsr/armv8 kernel configuration closer to the Linux
arm64 defconfig, synchronize options related to CPU features
(especially more recent Armv8.X variants), scheduler, EFI vars,
CMA and scheduler options.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
x86/64 enables support for KVM so I can't see a reason why
not on armsr/armv8 as well.
Arm CPU errata workaround items related to virtualization
are also enabled by this change.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
To reduce differences with the Linux arm64 defconfig,
sync the enabled erratum items with defconfig.
There are still some options not selected due to
CONFIG_KVM or other options not enabled in OpenWrt
by default.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
This compiles the CONFIG_PTP_1588_CLOCK support into the kernel binary
and activates the drivers for KVM and VMware which allow syncing the
host time with the VM when OpenWrt is running in a VM. With this change
the CONFIG_HYPERV_UTILS driver is now build into the kernel, because it
depends on the PTP framework being compiled in. CONFIG_HYPERV_UTILS was
build as a module, but not packages before.
Fixes: #13277
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This activates PCI Express ASPM control in Linux. Without this option it
is completely controlled by the BIOS, now Linux will take over and apply
some workarounds if needed.
Fixes: #13248
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
It seems that the Meraki bootloader does not respect the kernel ARM booting
specification[1] that requires that address where DTB is located needs to
be 64-bit aligned and often places the DTB on a non 64-bit aligned address
and then kernel fails to find the DTB magic and fails to boot.
Even worse, there is no prints until early printk is enabled and then its
visible that kernel is trying to find the ATAG-s as DTB was not found or
is invalid.
Unifi 6 devices had the same issue and it can be solved by passing the
load adress as part of the FIT image.
It seems that the vendor was aware of the issue and is always relocating
the DTB to 0x89000000, so lets just do the same.
Now that booting is reliable, reenable default images for the Meraki MR33
and MR74 devices.
Reviewed-by: Lech Perczak lech.perczak@gmail.com
Signed-off-by: Robert Marko <robimarko@gmail.com>
ipq40xx was converted to DSA and swconfig is not being included at all in
the default packages so there is no need to drop it from device packages.
Signed-off-by: Robert Marko <robimarko@gmail.com>
MR33 and MR74 share pretty much everything in the image recipe, so lets
extract a common recipe to avoid duplication.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Rename two patches which were only accepted in Linux 6.2, but were
marked as if they were accepted in Linux 6.1.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
the Marvell 10G PHY driver is no way specific to ARM SystemReady
systems, it frequently occurs on SFP+ copper modules and is useful on
many targets.
Hence it been added to package/kernel/linux/modules/netdevices and we
can remove the now redundant target-specific module.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
A dependency of the MT7988 MMC host controller on the SoC's RTC clock
being running has been discovered. Mark RTC clock as critical to fix
MMC host on MT7988.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The Bananapro board has an Ampak 6181 onboard (BCM43362/1), enable
the firmware files in the device profile, and add wpad-basic-mbedtls.
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
The X-Powers AC100 is a multi-function IC used to provide RTC
and audio codec via RSB (reduced serial bus, an Allwinner-
speciality). On some boards using the A80/A83T SoCs, aside
from the RTC functionality, the RTC is used as a clocksource
for the Ampak WiFi/BT modules.
Add modules for the core MFD support and the RTC.
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
This has been a part of modified upstream patch but got lost on major
kernel bump to 5.15, so bring it back.
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
[Add patch for kernel 6.1 too]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The v6.1 kernel has moved around the options for the RTL8366RB
DSA switch used in the DIR-685 so it was missing when building
the kernel. Fix it up by adding the right Kconfig options.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Hardware
--------
SOC: MediaTek MT7986A
RAM: 1GB DDR4
FLASH: 4GB eMMC
WiFi: 2x2 2.4 GHz 802.11 b/g/n/ax MT7916 DBDC
4x4 5 GHz 802.11 a/n/ac/ax MT7986
2x2 6 GHz 802.11ax MT7916 DBDC
ETH: 4x LAN 1Gbit/s (MT7531)
1x WAN 2.5Gbit/s (GPY211)
BTN: RESET, WPS
LED: Antenna LEDs (GPIO)
Mood-LED (Kinetic KTD2601) - unsupported
UART: Header nest to USB port - 3V3 115200 8N1
[BUTTON] GND - RX - TX [USB]
Installation
------------
1. Connect to the device using serial console.
2. Interrupt the Autoboot process when promted by sending '0' twice.
3. Serve the OpenWrt initramfs image using TFTP at 192.168.1.66. Name
the image "predator.bin" and conenct the TFTP server to the routers
LAN port.
4. Configure U-Boot to allow loading unsigned images from MMC
$ setenv bootcmd 'mmc read 0x40000000 0x00004400 0x0010000;
fdt addr $(fdtcontroladdr); fdt rm /signature; bootm 0x40000000';
saveenv
5. Transfer the image from U-Boot
$ setenv serverip 192.168.1.66; setenv ipaddr 192.168.1.1;
tftpboot 0x46000000 predator.bin; fdt addr $(fdtcontroladdr);
fdt rm /signature; bootm
6. Wait for OpenWrt to boot
7. Transfer the OpenWrt sysupgrade image to the router using scp.
8. Install OpenWrt using sysupgrade.
Signed-off-by: David Bauer <mail@david-bauer.net>
When building with Linux 5.15 the 'const' type results in warnings.
Restore the original non-const type in those cases.
Fixes: 36d0aa9c2d ("mediatek: filogic: sync pinctrl-mt7988 with MediaTek SDK")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
With an initial set of patches and configs in place let's start testing
with kernel 6.1.
Run-tested on the cortexa9 subtarget (WRT1900ACS, Turris Omnia)
Tested-by: Etienne Champetier <champetier.etienne@gmail.com>
Signed-off-by: Stefan Kalscheuer <stefan@stklcode.de>
