CONFIG_HARDEN_BRANCH_PREDICTOR option is included two times in this
configuration file. Remove one definition. On arm32 SoC it should not be
needed.
Fixes: 54f9744c82 ("treewide: disable spectre mitigation on unaffected Arm32 targets")
Link: https://github.com/openwrt/openwrt/pull/16743
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This driver allows retrieving MAC addresses and other factory information
via the NVMEM framework on Adtran devices.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
All boards using the deprecated uImage.FIT partition parser have
been migrated to the new fitblk driver. Drop the now no longer
needed partition parser.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Specification:
- MT7629 CPU
- MT7531 switch
- MT7761N and MT7762N wifi
- 256 MB RAM
- 128 MB NAND flash with dual-boot partitions
- 2 buttons: WPS and reset
- 1 WAN port (1G)
- 4 LAN ports (1G)
- 1 USB port
Limitations (same as other MT7629/MT7761N/MT7762N devices):
- Wifi is not working
- Second core is not working (kernel error message "CPU1: failed to come online")
Disassembly:
- There are two screws under the front rubber feet and two under the label on the bottom (in the corners towards the back, you should be able to feel them).
Serial Interface:
- UART pin header is already soldered on the board. Pinning from front to back:
1 - VCC
2 - TX
3 - RX
4 - n/a
5 - GND
GPIO:
- 1 white LED, connected to GPIO 52
- 1 reset button, connected to GPIO 60
- 1 WPS button, connected to GPIO 58
MAC Adresses:
- The MAC address printed on the device label is used for LAN and WAN
- The MAC address is stored in the devinfo partition in ASCII format (hw_mac_addr=aa:bb:cc:dd:ee)
- 2.4 GHz wifi uses MAC of the device label + 1
- 5 GHz wifi uses MAC of the device label + 2
Flashing:
- OpenWrt is only runnig in the first partition of dual boot
- To ensure to be able to go back to the factory image, flash the last OEM firmware via OEM web interface. This will ensure that the OEM firmware is present on both partitions
- Because of dual boot partitions, flashing via OEM interface is not supported
- Start a TFTP server and provide the initramfs image. Default settings:
- Router IP: 192.168.1.1
- TFTP server IP: 192.168.1.100
- TFTP file name: 7531.bin
- Open the device, connect UART and select " 1. System Load Linux to SDRAM via TFTP." during startup
- Adapt the settings to your environment, if required
- After initramfs is booted, flash the sysupgrade image
Return to OEM firmware:
- Run the following commands in OpenWrt to switch to the second partition
fw_setenv boot_part 2
fw_setenv bootimage 2
- Reboot the device. OEM firmware will start up again
Signed-off-by: Roland Reinl <reinlroland+github@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16067
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Airoha EN8801SC PHY is a gigabit PHY used on Edgecore EAP111 so, include
the MTK driver with some cleanups.
Unfortunatelly, there is no specification sheet nor datasheet available
in order to demistify the magic PBUS writes and work on upstreaming
this driver.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
When building MT7629 with ALL_KMODS then we get prompted for
LEDS_SMARTRG_LED and this will break CI and in future buildbot compilation.
It depends on I2C so the symbol is hidden until ALL_KMODS is used and I2C
support is available, so disable the LEDS_SMARTRG_LED symbol in 6.6 config
intentionally as is done in the 6.1 mt7629 config.
Signed-off-by: Robert Marko <robimarko@gmail.com>
The partition parser approach has been rejected upstream, it will be
replaced by a small block driver which is the solution suggestion by
upstream maintainers.
As the partition parser has only been used by the mediatek target, as
a first step, move it there.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Import driver for I2C-connected HolTek MCU controlling the RGBW LED
found in Adtran SmartRG devices.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Device specification:
- MT7629 with 16MB NOR flash W25Q128 and 128 MB DDR3 RAM.
- MT7761N and MT7762N wireless chips (currenlty no driver in OpenWrt available)
- WiFi is NOT working on this device
- Dual core but second CPU doesn't seem to work (Error message during boot: "CPU1: failed to come online")
There are two similar merge requests for similar devices with the same issues:
- https://github.com/openwrt/openwrt/pull/12286
- https://github.com/openwrt/openwrt/pull/5084
UART interface is next to the reset button, pinout:
- 1: TX (the pin with the arrow marker)
- 2: RX
- 3: GND
- 4: VCC
UART settings: 115200,8n1, 3.3V
U-Boot menu can be entered by pressing Ctrl+B during startup.
Booting initramfs:
- Set your computers IP adress to 192.168.1.110
- Run a TFTP server providing the initramfs image
- Power on the AP, press Ctrl+B to get to the U-Boot menu
- Select "1. System Load Linux to SDRAM via TFTP"
- Update kernel file name, input server IP and input device IP (if they deviate from the defaults)
- After booting, create a backup of all partitions, especially for kernel and root_fs. They are required for reverting back to stock firmware
- The sysupgrade image can be flashed now
MAC adresses:
- LAN and 2.4GHz use the same MAC (the one printed on the device)
- 5GHz WiFi MAC is LAN MAC + 1
GPIOs:
- GPIO 21 is the reset pin (low active)
- GPIO 55 is for the green LED (active high)
- GPIO 56 is for the yellow/amber LED (active high)
Signed-off-by: Roland Reinl <reinlroland+github@gmail.com>
Netgear EX6250v2, EX6400v3, EX6410v2, EX6470 are wall-plug 802.11ac
(Wi-Fi 5) extenders. Like other MT7629 devices, Wi-Fi does not work
currently as there is no driver.
Related: https://github.com/openwrt/openwrt/pull/5084
For future reference, 2.4GHz MAC = LAN+1, 5GHz MAC = LAN+2.
Specifications:
* MT7629, 256 MiB RAM, 16 MiB SPI NOR
* MT7761N (2.4GHz) / MT7762N (5GHz) - no driver
* Ethernet: 1 port 10/100/1000
* UART: 115200 baud (labeled on board)
Installation:
* Flash the factory image through the stock web interface, or TFTP to
the bootloader. NMRP can be used to TFTP without opening the case.
* After installation, perform a factory reset. Wait for the device to
boot, then hold the reset button for 10 seconds. This is needed
because sysupgrade in the stock firmware will attempt to preserve its
configuration using sysupgrade.tgz.
See https://github.com/openwrt/openwrt/pull/4182
Revert to stock firmware:
* Flash the stock firmware to the bootloader using TFTP/NMRP.
Signed-off-by: Wenli Looi <wlooi@ucalgary.ca>
Backport commits adding support for the MT7988 built-in switch to the
mt7530 driver.
This change results in the Kconfig symbol NET_DSA_MT7530 to be extended
by NET_DSA_MT7530_MDIO (everything formally covered by NET_DSA_MT7530)
and NET_DSA_MT7530_MMIO (a new driver for the MMIO-connected built-in
switch of the MT7988 SoC).
Select NET_DSA_MT7530_MDIO for all targets previously selecting
NET_DSA_MT7530, with the exception of mediatek/filogic which also
selects NET_DSA_MT7530_MMIO.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This adds clock drivers for the MediaTek MT7988 SoC
Signed-off-by: Sam Shih <sam.shih@mediatek.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Fix following error when building 32bit arm targets with kmod-crypto-sha512
ERROR: module '/home/user/openwrt/build_dir/target-arm_xscale_musl_eabi/linux-kirkwood_generic/linux-5.15.109/arch/arm/crypto/sha512-arm.ko' is missing.
Signed-off-by: Lu jicong <jiconglu58@gmail.com>
Kernel setting CONFIG_IO_URING supports high-performance I/O for file
access and servers, generally for more performant platforms, and adds
~45 KB to kernel sizes. The need for this on less "beefy" devices is
questionable, as is the size cost considering many platforms have kernel
size limits which require tricky repartitioning if outgrown. The size
cost is also large relative to the ~180 KB bump expected between major
OpenWRT kernel releases.
No OpenWrt packages have hard dependencies on this; samba4 and mariadb
can take advantage if available (+KERNEL_IO_URING:liburing) but
otherwise build and work fine.
Since CONFIG_IO_URING is already managed via the KERNEL_IO_URING setting
in Config-kernel.in (default Y), remove it from those target configs
which unconditionally enable it, and update the defaults to enable it
conditionally only on more powerful 64-bit x86 and arm devices. It may
still be manually enabled as needed for high-performance custom builds.
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
This activates CONFIG_HARDENED_USERCOPY for the remaining targets. This
adds additional checks in the copy_from_user() and copy_to_user()
functions.
This was not activated for ARCHS38 before because of a bug in the Linux
kernel 5.4 till 5.14, which as fixed and is described here:
https://github.com/foss-for-synopsys-dwc-arc-processors/linux/issues/15
I do not know why this was deactivated for mt7629 and rockchip.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Backport driver for common clocks in MT7981 SoC. The driver has also
been submitted upstream and became part of Linux 6.3.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Hardware:
SoC: MediaTek MT7629 Cortex-A7 (ARMv7 1.25GHz, Dual-Core)
RAM: DDR3 128MB
Flash: Macronix MX35LF1GE4AB (SPI-NAND 128MB)
WiFi: MediaTek MT7761N (2.4GHz) / MediaTek MT7762N (5GHz) - no driver
Ethernet: SoC (WAN) / MediaTek MT7531 (LAN x4)
UART: [GND, RX, TX, 3.3V] (115200)
Installation:
- Flash recovery image with TFTP recovery
Revert to stock firmware:
- Flash stock firmware with TFTP recovery
TFTP Recovery method:
1. Unplug the router
2. Hold the reset button and plug in
3. Release when the power LED stops flashing and go off
4. Set your computer IP address manually to 192.168.0.x / 255.255.255.0
5. Flash image with TFTP client to 192.168.0.1
Signed-off-by: Yoonji Park <koreapyj@dcmys.kr>
It will be supported by the new filogic subtarget
Signed-off-by: Sam Shih <sam.shih@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
All targets expect the malta target already activate the CONFIG_GPIOLIB
option. Move it to generic kernel configuration and also activate it for
malta.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
When building the mediatek/mt7629 target in OpenWrt 22.03 the kernel
does not have a configuration option for CONFIG_CRYPTO_DEV_MEDIATEK. Add
this option to the generic kernel configuration and also add two other
configuration options which are removed when we refresh the mt7629
kernel configuration.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This is now built-in, enable so it won't propagate on target configs.
Link: https://lkml.org/lkml/2022/1/3/168
Fixes: 79e7a2552e ("kernel: bump 5.15 to 5.15.44")
Fixes: 0ca9367069 ("kernel: bump 5.10 to 5.10.119")
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
(Link to Kernel's commit taht made it built-in,
CRYPTO_LIB_BLAKE2S[_ARM|_X86] as it's selectable, 5.10 backport)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Remove patches and configuration for Linux 5.10 which have been left
in the tree despite the target having been switched to Linux 5.15.
Fixes: c283defa88 ("mediatek: switch to 5.15")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Each of
- CRYPTO_AEAD2
- CRYPTO_AEAD
- CRYPTO_GF128MUL
- CRYPTO_GHASH
- CRYPTO_HASH2
- CRYPTO_HASH
- CRYPTO_MANAGER2
- CRYPTO_MANAGER
- CRYPTO_NULL2
either directly required for mac80211 crypto support, or directly
selected by such options. Support for the mac80211 crypto was enabled in
the generic config since c7182123b9 ("kernel: make cryptoapi support
needed by mac80211 built-in"). So move the above options from the target
configs to the generic config to make it clear why do we need them.
CC: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Both CLANG_VERSION and LLD_VERISON are autogenerated runtime
configuration options, so add them to the kernel configuration filter
and remove from generic and per-target configs to keep configs clean.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
CONFIG_RCU_{NEED_SEGCBLIST,STALL_COMMON} are set basically everywhere. Move them
to the generic kconfigs. And resort the generic kconfigs while at it.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
These options doesn't show up unless some kernel packages are selected,
so they are not covered by kernel_menuconfig.
Manually add them so that a build with all kmods can pass without user
interaction.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
It is possible to select CONFIG_MTD_PARSER_TRX on the mediatek now. Add
this option to the kernel configuration file.
Fixes: 58c5e25664 ("mediatek: support non standard trx magic values")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
For the targets which enable ubifs, these symbols are already part of the
generic kconfigs. Drop them from the target kconfigs.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
So far, board.d files were having execute bit set and contained a
shebang. However, they are just sourced in board_detect, with an
apparantly unnecessary check for execute permission beforehand.
Replace this check by one for existance and make the board.d files
"normal" files, as would be expected in /etc anyway.
Note:
This removes an apparantly unused '#!/bin/sh /etc/rc.common' in
target/linux/bcm47xx/base-files/etc/board.d/01_network
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Add a driver for controlling the RGB LED via Ubiquitis own "LEDBAR" LED
controller based on the Holtek HT32F52241 MCU.
This driver is initially used by the Ubiquiti UniFi 6 LR, however
judging from FCC pictures the MCU is also found on the U6-Mesh as well
as the U6-Extender.
Signed-off-by: David Bauer <mail@david-bauer.net>
