It allows prepopulating /etc/config/network interface-s with predefined
metric. It may be useful for devices with multiple WAN ports.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
btusb fails to start on MT792[12] hardware without the appropriate
firmware being loaded first:
[ 9.750285] bluetooth hci0: Direct firmware load for mediatek/BT_RAM_CODE_MT7961_1_2_hdr.bin failed with error -2
[ 9.765723] bluetooth hci0: Falling back to sysfs fallback for: mediatek/BT_RAM_CODE_MT7961_1_2_hdr.bin
Package firmware for MediaTek MT792[12] Bluetooth from linux-firmware.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Enable MediaTek protocol in btusb module to support e.g. the Bluetooth
part of the MT7921K NGFF/M.2 module.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Pakedge WR-1 is a dual-band wireless router.
Specification
SoC: Qualcomm Atheros IPQ4018
RAM: 256 MB DDR3
Flash: 32 MB SPI NOR
WIFI: 2.4 GHz 2T2R integrated
5 GHz 2T2R integrated
Ethernet: 5x 10/100/1000 Mbps QCA8075
USB: 1x 2.0
LEDS: 8x (3 GPIO controlled, 5 connected to switch)
Buttons: 1x GPIO controlled
UART: pin header J5
1. 3.3V, 2. GND, 3. TX, 4. RX
baud: 115200, parity: none, flow control: none
Installation
1. Rename initramfs image to:
openwrt-ipq806x-qcom-ipq40xx-ap.dk01.1-c1-fit-uImage-initramfs.itb
and copy it to USB flash drive with FAT32 file system.
2. Connect USB flash drive to the router and apply power while pressing
reset button. Hold the button, on the lates bootloader version, when
Power and WiFi-5 LEDs will start blinking release it. For the older
bootloader holding it for 15 seconds should suffice.
3. Now the router boots the initramfs image, at some point (close to one
minute) the Power LED will start blinking, when stops, router is fully
booted.
4. Connect to one of LAN ports and use SSH to open the shell at
192.168.1.1.
5. ATTENTION! now backup the mtd8 and mtd9 partitions, it's necessary if,
at some point, You want to go back to original firmware. The firmware
provided by manufacturer on its site is encrypted and U-Boot accepts
only decrypted factory images, so there's no way to restore original
firmware.
6. If the backup is prepared, transfer the sysupgrade image to the router
and use 'sysupgrade' command to flash it.
7. After successful flashing router will reboot. At some point the Power
LED will start blinking, wait till it stops, then router is ready for
configuration.
Additional information
U-Boot command line is password protected. Password is unknown.
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Devices using GPT usually have FAT filesystem on boot partition and
that's where the intermediary backup of system configuration is stored
on sysupgrade. Automatic restoring of OpenWrt configuration after
sysupgrade will be inhibited if the driver is not loaded and file system
type is not specified in mount command.
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Update host build of fiptool and use the new python sptool.py instead
of the previous sptool executable.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
There are two feature currently altered by the multicast_to_unicast option.
1. bridge level multicast_to_unicast via IGMP snooping
2. hostapd/mac80211 config multicast_to_unicast setting
The hostapd/mac80211 setting has the side effect of converting *all* multicast
or broadcast traffic into per-station duplicated unicast traffic, which can
in some cases break expectations of various protocols.
It also has been observed to cause ARP lookup failure between stations
connected to the same interface.
The bridge level feature is much more useful, since it only covers actual
multicast traffic managed by IGMP, and it implicitly defaults to 1 already.
Renaming the hostapd/mac80211 option to multicast_to_unicast_all should avoid
unintentionally enabling this feature
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Commit 0b7c66c ("at91bootstrap: add sama5d27_som1_eksd1_uboot as
default defconfig") changed default booting media for sama5d27_som1_ek
board w/o any reason. Changed it back to sdmmc0 as it is for all the
other Microchip supported distributions for this board (Buildroot,
Yocto Project). The initial commit cannot be cleanly reverted.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Commit adc69fe (""uboot-at91: changed som1 ek default defconfigs")
changed the booting media to sdmmc1 as default booting w/o any reason.
The Microchip releases for the rest of supported distributions (Buildroot,
Yocto Project) uses sdmmc0 as default booting media for this board.
Thus change it back to sdmmc0. With this remove references to sdmmc1
config. The initial commit cannot be cleanly reverted.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
f5d02c32f811 pex: add support for sending endpoint notification from the wg port via raw socket
c3b1127236a0 ubus: add support for querying active networks
8ad119715168 ubus: add support for adding auth_connect hosts at runtime
26dc52789d41 network: add support for configuring extra peers via a separate json file
d7fb9e5b065b ubus: add reload command
Signed-off-by: Felix Fietkau <nbd@nbd.name>
f5fcdcf cli: introduce test mode and refuse firewall restart on errors
a540f6d fw4: fix cosmetic issue with per-ruleset and per-table include paths
695e821 doc: fix swapped include positions in nftables.d README
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Weijie Gao has submitted an updated version of the patchset adding
support for MT7986 and MT7981 to U-Boot. Use that v2 patchset.
Changes of v2:
- Add cpu driver for print_cpuinfo()
- Fix NULL pointer dereference in mtk_image
(was already fixed in OpenWrt)
- Fix coding style
- Minor changes
https://patchwork.ozlabs.org/project/uboot/list/?series=316148
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Create new mediatek_filogic file and add entries for environment on
MMC, UBI and NOR for the Bananapi BPi-R3.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The Bananapi BPi-R3 board can boot from eMMC, SD card, SPI-NAND and
SPI-NOR, depending on the position of switches controlling the BOOTSEL
bootstrap pins as we as hard-wired chip-select lines. The position of the
chip-select switch SW6 decides whether either SD card or eMMC can be
accessed, SW5 selects either SPI-NAND or SPI-NOR.
Generate U-Boot for all 4 boot options. The SD card version allows
installation to SPI-NAND and SPI-NOR (eMMC cannot be accessed
simultanously with the SD card), the SPI-NAND version allows installation
to eMMC.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Testing has shown it to be very unreliable in variety of configurations.
It is not mandatory, so let's disable it by default until we have a better
solution.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
344fa9e lib: extend render() to support function values
89452b2 lib: improve getenv() and split() implementations
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
b75791a6db25 scripts/update-cmd.pl: reorder add/remove calls to better deal with dynamic changes
c29e1ad045d0 scripts/update-cmd.pl: set device up before adding routes/addresses
5ad35ce4beea scripts/update-cmd.pl: run update two times
5d79b88f00c1 add support for overriding peer-exchange-port for individual hosts
0041fcacb624 add support for disabling VXLAN/eBPF support
Signed-off-by: Felix Fietkau <nbd@nbd.name>
5cbd55f60346 unet-cli: fix formatting of help text
59b97448b636 build.sh: force use of -fPIC on static libraries to fix build error
74a14c00abb0 pex-msg: fix siphash key initializer
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This forces a rebuild of the wolfssl package when the
libwolfssl-benchmark OpenWrt package gets activated or deactivated.
Without this change the wolfssl build will fail when it compiled without
libwolfssl-benchmark before and it gets activated for the next build.
Fixes: 18fd12edb8 ("wolfssl: add benchmark utility")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
