Commit Graph

21916 Commits

Author SHA1 Message Date
Adrian Schmutzler
c642a97aa6 ath79: add support for TP-Link TL-WDR4300 v1 (IL)
The TL-WDR4300 v1 sold in Israel has a different TPLINK_HWID.

Thanks to Josh4300 for testing on device.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-12-12 14:42:05 +01:00
Adrian Schmutzler
8e91b18ab7 ath79: redistribute UBNT variables in Ubiquiti image Makefile
The variables UBNT_BOARD and UBNT_VERSION are defined in the parent
Device/ubnt definition and then overwritten for most of the derived
platform definitions (e.g. Device/ubnt-wa).

Since this mixed use of inheritance and overwriting can be misleading,
this moves the variables to the platform-based definitions.

While at it, reorder the definitions to have order consistent, too.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-12-12 13:18:01 +01:00
Adrian Schmutzler
68ef534989 ramips: add label MAC address for Mikrotik RBM33G
The device label contains:
E01: B8:69:F4:xx:xx:07
E02: B8:69:F4:xx:xx:09

The first value corresponds to the address set in hard_config 0x10.

That one is taken for the label MAC address.

Thanks to Martin Schiller for retrieving the information.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-12-12 13:12:11 +01:00
Adrian Schmutzler
772af7f98d ramips: rt305x: use flash location for wan_mac in 02_network
This uses the flash locations instead of eth0 MAC address to
calculate MAC address increments for WAN.

The change will make the MAC address setup of a particular device
more obvious and removes the dependency of 02_network on the eth0
initialization.

This removes the wan_mac setup for the following devices as they
do not set up a MAC address for ethernet in the first place:
- asiarf,awapn2403
- belkin,f7c027
- dlink,dir-615-d
- mofinetwork,mofi3500-3gn
- prolink,pwh2004
- ralink,v22rw-2x2
- unbranded,wr512-3gn-4m
- unbranded,wr512-3gn-8m

While at it, make some DT node labels consistent with the label
property.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-12-12 13:11:58 +01:00
Adrian Schmutzler
a858d6d0e2 ramips: rt288x: use flash location for wan_mac in 02_network
This uses the flash locations instead of eth0 MAC address to
calculate MAC address increments for WAN.

The change will make the MAC address setup of a particular device
more obvious and removes the dependency of 02_network on the eth0
initialization.

This removes the wan_mac setup for ralink,v11st-fe as this device
does not set up a MAC address for ethernet in the first place.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-12-12 13:11:49 +01:00
Adrian Schmutzler
fef1810897 ramips: mt76x8: use flash location for wan_mac in 02_network
This uses the flash locations instead of eth0 MAC address to
calculate MAC address increments for WAN.

The change will make the MAC address setup of a particular device
more obvious and removes the dependency of 02_network on the eth0
initialization.

While at it, change the partition label for zyxel,keenetic-extra-ii
to factory to be consistent with node label and all the other devices.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-12-12 13:11:39 +01:00
Adrian Schmutzler
ed975a58e4 ramips: mt7621: use flash location for wan_mac in 02_network
This uses the flash locations instead of eth0 MAC address to
calculate MAC address increments for WAN.

The change will make the MAC address setup of a particular device
more obvious and removes the dependency of 02_network on the eth0
initialization.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-12-12 13:11:28 +01:00
Adrian Schmutzler
98d9158d2f ramips: mt7620: use flash location for wan_mac in 02_network
This uses the flash locations instead of eth0 MAC address to
calculate MAC address increments for WAN.

The change will make the MAC address setup of a particular device
more obvious and removes the dependency of 02_network on the eth0
initialization.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-12-12 13:11:18 +01:00
Adrian Schmutzler
38866f275d ramips: remove wan_mac setup for evaluation boards
The evaluation boards do not set up a MAC address for eth0
in the first place, so it does not make sense to calculate a WAN
address from the random MAC used there.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-12-12 13:11:11 +01:00
Adrian Schmutzler
757658f2ab ramips: create common DTSI for TP-Link Archer C20i/C20 v1/C50 v1
The TP-Link Archer C20i/C20 v1/C50 v1 seem to be almost the same,
so creating a common DTSI will reduce duplicate code.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-12-12 13:11:04 +01:00
Adrian Schmutzler
c4f6850efc ramips: remove unused DTS variable from DEVICE_VARS
The DTS variable has been removed in 402138d12d ("ramips: Derive
DTS name from device name in Makefile"), but the DEVICE_VARS entry
has been overlooked.

Remove it now since we are not using this variable.

This must _not_ be backported to 19.07, where the variable is still
in use.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-12-12 13:10:57 +01:00
Gabor Varga
a283b1788a ramips: fix switch port numbering for RT-AC65P/RT-AC85P
The switch LAN port numbers are in reversed order with original config.
With this patch they are fixed.

Port order checked on both devices.

Signed-off-by: Gabor Varga <vargagab@gmail.com>
[merged definitions into appropriate block, extended commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-12-11 23:00:32 +01:00
Adrian Schmutzler
e00396d584 ramips: add label MAC address for TP-Link Archer C20i
Current OpenWrt MAC setup:
eth0             &rom 0xf100    :48
eth0.2           eth0+1         :49
wlan0 (5 GHz)    &radio 0x8004  different OUI
wlan1 (2.4 GHz)  &radio 0x4     same OUI as wlan0

Label MAC address corresponds to eth0 (&ethernet).

No additional addresses found in hexdump of rom/radio.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-12-11 22:51:04 +01:00
DENG Qingfang
46c74944df ath79: fix typos in DTS
Replace "usb_ochi" with "usb_ohci", and "usb_echi" with "usb_ehci".

Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
2019-12-11 22:50:12 +01:00
Koen Vandeputte
88ca372b5a kernel: bump 4.19 to 4.19.88
Refreshed all patches.

Remove upstreamed:
- 0004-boot-sq201-from-sda1.patch
- 500-v4.20-ubifs-Fix-default-compression-selection-in-ubifs.patch
- 0003-usb-dwc2-use-a-longer-core-rest-timeout-in-dwc2_core.patch

Altered patches:
- 0011-ARM-dts-Fix-up-SQ201-flash-access.patch
- 400-mtd-add-rootfs-split-support.patch
- 0101-pci-mediatek-backport-fix-pcie.patch

Compile-tested on: cns3xxx
Runtime-tested on: cns3xxx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-12-10 09:50:42 +01:00
Koen Vandeputte
d395583d69 kernel: bump 4.14 to 4.14.158
Refreshed all patches.

Altered patches:
- 400-mtd-add-rootfs-split-support.patch

Compile-tested on: cns3xxx
Runtime-tested on: cns3xxx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-12-10 09:50:42 +01:00
Koen Vandeputte
a9b9592196 kernel: bump 4.9 to 4.9.206
Refreshed all patches.

Altered patches:
- 400-mtd-add-rootfs-split-support.patch

Compile-tested on: none
Runtime-tested on: none

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-12-10 09:50:42 +01:00
Daniel Golle
e964338110 malta: remove CONFIG_LEGACY_PTY from kernel config
Having legacy PTYs enabled causes problems with procd-hotplug.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2019-12-09 20:16:53 +01:00
Daniel Golle
2105354968 sunxi: remove CONFIG_LEGACY_PTY from kernel config
Having legacy PTYs enabled causes problems with procd-hotplug.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2019-12-09 20:15:36 +01:00
Daniel Golle
414d027ae8 layerscape: remove CONFIG_LEGACY_PTY from kernel config
Having legacy PTYs enabled causes problems with procd-hotplug.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2019-12-09 20:15:02 +01:00
Daniel Golle
411e824ec3 kirkwood: remove CONFIG_LEGACY_PTY from kernel config
Having legacy PTYs enabled causes problems with procd-hotplug.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2019-12-09 20:14:20 +01:00
Daniel Golle
c1db4d9c56 at91: disable legacy PTYs and virtual terminals
Enabling legacy PTYs causes problems with procd-hotplug.
And as this is a headless target, no need to have virtual terminals.
Remove corresponding kernel config options, they are disabled in
generic kernel config.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2019-12-09 20:14:17 +01:00
Daniel Golle
d0d7f5d9e4 mpc85xx: remove CONFIG_LEGACY_PTY from kernel config
Having legacy PTYs enabled causes problems with procd-hotplug.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2019-12-09 20:14:17 +01:00
Daniel Golle
8069e9734b ixp4xx: remove CONFIG_LEGACY_PTY from kernel config
Having legacy PTYs enabled causes problems with procd-hotplug.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2019-12-09 20:14:17 +01:00
Daniel Golle
dcf48fda05 uml: remove CONFIG_LEGACY_PTY from kernel config
Having legacy PTYs enabled causes problems with procd-hotplug.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2019-12-09 20:14:17 +01:00
Daniel Golle
c881769a55 oxnas: disable legacy PTYs and virtual terminals
Enabling legacy PTYs causes problems with procd-hotplug.
And as this is a headless target, no need to have virtual terminals.
Remove corresponding kernel config options, they are disabled in
generic kernel config.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2019-12-09 20:14:11 +01:00
Adrian Schmutzler
231dc26867 treewide: remove dts-v1 identifier from DTSI files
The "/dts-v1/;" identifier is supposed to be put once at the beginning
of a device tree file. Thus, it makes no sense to provide it a second
time in to-be-included DTSI files.

This removes the identifier from all DTSI files in /target/linux.

Most of the DTS files in OpenWrt do contain the "/dts-v1/;". It is
missing for most of the following targets, though:
mvebu, ipq806x, mpc85xx, ipq40xx

This does not touch ipq806x for now, as the bump to 4.19 is close.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-12-08 16:44:06 +01:00
Olli Asikainen
deb835849a brcm47xx: add switch configuration for WNR3500L
Netgear WNR3500L is an already supported device, but out of the
box, the device has no switch configuration and there is no wan.
The correct configuration for this specific model is similar to
some other models. This simple commit adds the correct switch
and the out-of-the-box experience is improved.

Experimentally determined:

Port 0 => WAN
Port 1..4 => LAN
Port 5..7 => unused
Port 8 => CPU

Signed-off-by: Olli Asikainen <olli.asikainen@gmail.com>
Tested-by: Fabian Zaremba <fabian@youremail.eu>
[added port mapping to commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-12-08 00:21:36 +01:00
Adrian Schmutzler
34abfb6e91 ramips: convert mediatek,mtd-eeprom from decimal to hex notation
A small subset of devices uses decimal notation for mediatek,mtd-eeprom
in DTS files. Convert to hexadecimal notation to be consistent with
all the rest.

Also change "0" to "0x0" in the same files for consistency.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-12-08 00:20:37 +01:00
Martin Schiller
3a55c7935d ramips: fix number of LAN Ports for Mikrotik RBM33G
The Mikrotik RBM33G has only 2 LAN ports.

Signed-off-by: Martin Schiller <ms@dev.tdt.de>
[moved node in 02_network to maintain alphabetic sorting]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-12-08 00:20:21 +01:00
Walter Sonius
a065cd29bf ramips: fix switch port order for TP-Link Archer C20i
Physical port order watched from the backside of the C20i
(from left to right) is: Internet / 1 / 2 / 3 / 4

Physical Port	Switch port
WAN             0
LAN 3           1
LAN 4           2
LAN 1           3
LAN 2           4
(not used)      5
CPU             6

Signed-off-by: Walter Sonius <walterav1984@gmail.com>
[commit message/title improvements]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-12-08 00:20:12 +01:00
Christian Lamparter
a428606646 ath79: fix WNDR3700/WNDR3800 wifi reg size
"[...] the size component shall be zero."
(See "PCI Bus Binding to: IEEE Std 1275-1994 Rev 2.1"
section "4.1.1 Open Firmware-defined Properties for Child Nodes")

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-12-07 12:01:23 +01:00
John Crispin
a512123a4b mediatek: fix pcie bringup issue
Signed-off-by: John Crispin <john@phrozen.org>
2019-12-05 15:29:46 +01:00
Stijn Tintel
157e17e985 ath79: add support for Ubiquiti LiteBeam AC Gen2
Hardware:
* SoC: Atheros AR9342-BL1A
* RAM: 64MB DDR2 (Winbond W9751G6KB-25)
* Flash: 16MB SPI NOR (Macronix MX25L12835FZ2I-10G)
* Ethernet: 1x 10/100/1000 Mbps (Atheros AR8035-A) with 24V PoE support
* Wifi 2.4GHz: Atheros AR9340 v2
* WiFi 5GHz: Ubiquiti U-AME-G1-BR4A (rebranded QCA988X v2)
* LEDs: 1x Power, 1x Ethernet
* Buttons: 1x Reset
* UART: 1x TTL 115200n8, 3.3V RX TX GND, 3.3V pin closest to RJ45 port

The LEDs do not seem to be connected to any GPIO, so there is currently
no way to control them.

Installation via U-Boot, TFTP and serial console:
* Configure your TFTP server with IP 192.168.1.254
* Connect serial console and power up the device
* Hit any key to stop autoboot
* tftpboot 0x81000000 openwrt-ath79-generic-ubnt_litebeam-ac-gen2-initramfs-kernel.bin
* bootm 0x81000000
* copy openwrt-ath79-generic-ubnt_litebeam-ac-gen2-squashfs-sysupgrade.bin
  to /tmp
* sysupgrade /tmp/openwrt-ath79-generic-ubnt_litebeam-ac-gen2-squashfs-sysupgrade.bin

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: Petr Štetiar <ynezz@true.cz>
Acked-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-12-04 23:17:41 +02:00
Stijn Tintel
db26f53bb3 ath79: drop IMAGE/factory.bin from ubnt-wa devices
The sysupgrade image contains OpenWrt specific metadata. Having this
metadata in the factory images makes no sense. Drop IMAGE/factory.bin
from Device/ubnt-wa and use the default from Device/ubnt instead.

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: Petr Štetiar <ynezz@true.cz>
Acked-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-12-04 23:17:41 +02:00
Kevin Darbyshire-Bryant
89b8dd62ce kernel: act_ctinfo: fix updated backport on 4.14
It turns out my 4.14 testing had a rather large flaw in it and the
'extack' mechanism isn't quite ready.  Remove the extack stuff from this
backport.

Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
2019-12-04 12:06:26 +00:00
Kevin Darbyshire-Bryant
1d608a10a0 kernel: act_ctinfo: update backport
Since the original backports from kernel 5.3 a few things have been
tweaked by kernel bumps & other upstream changes.  Update the backport
to reflect upstream as closely as possible and remove the bitrot.

Functions remain the same, error reporting improved.

Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
2019-12-03 21:41:35 +00:00
Adrian Schmutzler
f6385f30bd ath79: fix source of label MAC address for Ubiquiti XM devices
In d421a8b944 ("ath79: read label MAC address from flash instead
of using phy0/phy1") the source of the label MAC address was changed
for devices just reading it from phy0. To get rid of the dependency
from phy startup, addresses were read directly from the flash
locations that are used to initialize the phy MAC addresses.

Unfortunately, it turned out that Ubiquiti XM devices seem to have
different flash locations than expected, and also seem to have
specific locations for different devices (all in art/EEPROM):

0xe012 AR9280 Nanostation M2 - 0x120c
0xe035 AR9280 Nanostation M3 - 0x120c
0xe1b2 AR9280 Rocket M2 - 0x120c
0xe1c3 AR9280 Rocket M3 - 0x120c
0xe1b5 AR9280 Rocket M5 - 0x120c
0xe2d5 AR9280 Bullet M2 Titanium - 0x120c
0xe2b5 AR9280 Nanobridge M5 - 0x120c
0xe202 AR9280 Bullet M2 - 0x120c
0xe232 AR9287 Nanobridge M2 - 0x110c
0xe4a2 AR9285 AirRouter - 0xa0bf
Picostation M2 - 0x120c and 0xa0bf
Nanostation Loco M2 - not in 0x120c, other locations not checked

An additional problem of the Ubiquiti device support in OpenWrt is
that we provide images that match several subvariants of the devices,
which might have different MAC address locations.

Given that reading the address from phy0 in 02_network _is_ working
for the ath79 target in general, it does not seem reasonable to
rebuild a complex MAC address retrieval mechanism which is already
present in the ath9k driver.

So, this patch reverts the label MAC address source for Ubiquiti XM
devices (and the Unifi AP) to /sys/class/ieee80211/phy0/macaddress.

This doesn't affect XW and Unifi AC devices, where the label MAC
address source is defined via device tree.

For alfa-network,ap121f the location 0x1002 is kept, as this has
been verified during device support preparation in PR #2199.

Fixes: d421a8b944 ("ath79: read label MAC address from flash
instead of using phy0/phy1")

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-12-03 13:30:51 +01:00
Stijn Tintel
291d79935e octeon: fix sysupgrade
Sysupgrade was failing due to incorrect replacement of backticks:
/sbin/sysupgrade: /lib/upgrade/platform.sh: line 101: syntax error: missing '))'

Fixes: 0bbfc3dff7 ("octeon: replace backticks by $(...)")
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2019-11-30 20:19:12 +02:00
David Bauer
3f79aaa297 generic ar8xxx: increase VLAN table for AR83x7
The Atheros AR8327 and AR8337 have (according to their datasheet) a
VLAN table with a maximum of 4096 entries.

Currently, there's a hard limit of 128 VLANs, which is the same as
for most other Atheros switches. Increase this limit only for the
AR83x7 series and modify some shared functions to allow them to work
with a variable max VLAN count.

Signed-off-by: David Bauer <mail@david-bauer.net>
2019-11-30 16:49:05 +01:00
Christian Lamparter
82a741c774 mac80211: switch to upstream owl-loader driver
The Owl Loader (named after the codename that Atheros gave
these devices back in the day) has been accepted upstream.

This patch removes the "misc" driver OpenWrt had and adds
the remaining differences against the version that ships
with 5.4-rc1 into a separate "120-owl-loader-compat.patch"
file that can be cut down once AR71XX is being dealt with.

Note: I decided to keep the existing (kmod-)owl-loader
package name around for now. The kernel module file in
the kmod package will be called ath9k_pci_owl_loader.ko
though.

Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-11-30 13:21:20 +01:00
Robert Marko
146eb4925c ipq40xx: add support for Crisis Innovation Lab MeshPoint.One
MeshPoint.One is Wi-Fi hotspot and smart IoT gateway (based upon
Jalapeno module from 8Devices).

MeshPoint.One (https://meshpointone.com) is a unique Wi-Fi hotspot and
smart city gateway that can be installed and powered from street
lighting (even solar power in the future).  MeshPoint provides up to 27
hours of interrupted Wi-Fi and IoT services from internal battery even
when external power is not available.  MeshPoint.One can be used for
disaster relief efforts in order to provide instant Wi-Fi coverage that
can be easily expanded by just adding more devices that create wide area
mesh network.  MeshPoint.One devices have standard Luci UI for
management.

Features:
- 1x 1Gpbs WAN
- 1x 1Gbps LAN
- POE input (eth0)
- POE output (eth1)
- Sensor for temperature, humidity and pressure (Bosch BME280)
- current, voltage and power measurement via TI INA230
- Hardware real time clock
- optional power via Li-Ion battery
- micro USB port with USB to serial chip for easy OpenWrt terminal
  access
- I2C header for connecting additional sensors

Installation:
-------------
Simply flash the sysupgrade image from stock firmware.

Or use the built in Web recovery into bootloader:
Hold Reset button for 5 to 20 seconds or use UART and httpd command.
Web UI will appear on 192.168.2.100 by default.
For web recovery use the factory.ubi image.

Signed-off-by: Damir Samardzic <damir.samardzic@sartura.hr>
Signed-off-by: Damir Franusic <damir.franusic@sartura.hr>
Signed-off-by: Valent Turkovic <valent@meshpoint.me>
Signed-off-by: Robert Marko <robert@meshpoint.me>
[commit description long line wrap, usb->USB]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-11-30 00:53:36 +01:00
Robert Marko
c550b1acfc ipq40xx: use DTSI for Jalapeno
Lets move common code for Jalapeno into DTSI, this way Jalapeno based
boards don't introduce duplicate code.

While at it, lets also fix some style issues and update to current DTS
style.

Signed-off-by: Robert Marko <robert@meshpoint.me>
[commit description long line wrap]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-11-30 00:53:36 +01:00
Koen Vandeputte
7c76565d4c kernel: bump 4.9 to 4.9.205
Refreshed all patches.

Fixes:
- CVE-2019-18660

Compile-tested on: none
Runtime-tested on: none

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-11-29 17:05:38 +01:00
Koen Vandeputte
f19e471f32 kernel: bump 4.19 to 4.19.86
Refreshed all patches.

Altered patches:
- 950-0064-mfd-Add-Raspberry-Pi-Sense-HAT-core-driver.patch
- 0005-mtd-physmap_of-Move-custom-initialization.patch

Remove upstreamed:
- 0001-pinctrl-gemini-Mask-and-set-properly.patch
- 0002-pinctrl-gemini-Fix-up-TVC-clock-group.patch

Compile-tested on: cns3xxx
Runtime-tested on: cns3xxx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-11-29 09:59:49 +01:00
Koen Vandeputte
414b7c107a kernel: bump 4.14 to 4.14.156
Refreshed all patches.

Compile-tested on: cns3xxx
Runtime-tested on: cns3xxx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-11-29 09:59:49 +01:00
Adrian Schmutzler
118749271b mpc85xx: add vendor to Makefile node name, derive SUPPORTED_DEVICES
By adding the vendor to the Makefile device definition node name,
one can derive the standard compatible used in SUPPORTED_DEVICES
instead of having to specify it manually.

Despite, this moves the naming scheme closer to what is used for
other targets (ath79, ramips).

Build-tested on all subtargets.
Run-tested on TP-Link TL-WDR4900 v1.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-11-27 22:54:36 +01:00
Anderson Vulczak
9b90dc05f5 ath79: add support for TP-Link Archer C6 v2 (US) and A6 (US/TW)
This patch is based on #1689 and adds support for TP-Link Archer
C6 v2 (US) and A6 (US/TW).

The hardware is the same as EU and RU variant, except for GPIOs
(LEDS/Buttons), flash(chip/partitions) and UART being available
on the board.

- SOC: Qualcomm QCA9563 @ 775MHz
- Flash: GigaDevice GD25Q127CS1G (16MiB)
- RAM: Zentel A3R1GE40JBF (128 MiB DDR2)
- Ethernet: Qualcomm QCA8337N: 4x 1Gbps LAN + 1x 1Gbps WAN
- Wireless:
  - 2.4GHz (bgn) QCA9563 integrated (3x3)
  - 5GHz (ac) Qualcomm QCA9886 (2x2)
- Button: 1x power, 1x reset, 1x wps
- LED: 6x LEDs: power, wlan2g, wlan5g, lan, wan, wps
- UART: 115200, 8n1 (header available on board)

Known issues:
 - Wireless: 5GHz is known to have lower RSSI signal, it affects speed and range.

Flash instructions:

Upload openwrt-ath79-generic-tplink_archer-c6-v2-us-squashfs-factory.bin
via the router Web interface.

Flash instruction using tftp recovery:

1. Connect the computer to one of the LAN ports of the router
2. Set the computer IP to 192.168.0.66
3. Start a tftp server with the OpenWrt factory image in the
   tftp root directory renamed to ArcherA6v2_tp_recovery.bin.
4. Connect power cable to router, press and hold the
   reset button and turn the router on
5. Keep the reset button pressed until the WPS LED lights up
6. Wait ~150 seconds to complete flashing

Flash partitioning: I've followed #1689 for defining the partition layout
for this patch. The partition named as "tplink" @ 0xfd0000 is marked
as read only as it is where some config for stock firmware are stored.
On stock firmware those stock partitions starts at 0xfd9400 however
I had not been able to make it functional starting on the same address as
on stock fw, so it has been partitioned following #1689 and not the stock
partition layout for this specific partition. Due to that firmware/rootfs
partition lenght is 0xf80000 and not 0xf89400 as stock.

According to the GPL code, the EU/RU/JP variant does have different GPIO pins
assignment to LEDs and buttons, also the flash memory layout is different.

GPL Source Code: https://static.tp-link.com/resources/gpl/gpl-A6v2_us.tar.gz

Signed-off-by: Anderson Vulczak <andi@andi.com.br>
[wrap commit message, remove soft_ver change for C6 v2 EU, move LED aliases
to DTS files, remove dts-v1 in DTSI, node/property reorder in DTSI]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-11-27 22:54:36 +01:00
Adrian Schmutzler
c08ddfce3f ath79: rename EEPROM to art
This renames all remaining occurrences of "EEPROM" to "art" to
further harmonize the partition labelling in ath79. This will
help to reduce the amount of user-space code and might be
beneficial when code is copy/pasted in the future.

Affected are only devices from Ubiquiti, where the XM board is
already using "art" in ath79.

Acked-by: Piotr Dymacz <pepe2k@gmail.com>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-11-27 22:54:36 +01:00
Piotr Dymacz
e5d4c09667 ath79: add support for YunCore XD4200 and A782
YunCore XD4200 ('XD4200_W6.0' marking on PCB) is Qualcomm/Atheros based
(QCA9563, QCA9886, QCA8334) dual-band, Wave-2 AC1200 ceiling AP with PoE
(802.3at) support. A782 model ('T750_V5.1' marking on PCB) is a smaller
version of the XD4200, with similar specification but lower TX power.

Specification:

- QCA9563 (775 MHz)
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 2x 10/100/1000 Mbps Ethernet (QCA8334), with 802.3at PoE support (WAN)
- Wi-Fi 2.4 GHz:
  - XD4200: 2T2R (QCA9563), with ext. PA (SKY65174-21) and LNA
  - A782: 2T2R (QCA9563), with ext. FEM (SKY85329-11)
- Wi-Fi 5 GHz:
  - XD4200: 2T2R (QCA9886), with ext. FEM (SKY85728-11)
  - A782: 2T2R (QCA9886), with ext. FEM (SKY85735-11)
- LEDs:
  - XD4200: 5x (2x driven by SOC, 1x driven by AC radio, 2x Ethernet)
  - A782: 3x (1x RGB, driven by SOC and radio, 2x Ethernet)
- 1x button (reset)
- 1x UART (4-pin, 2.54 mm pitch) header on PCB
- 1x DC jack (12 V)

Flash instructions:

If your device comes with generic QSDK based firmware, you can login
over telnet (login: root, empty password, default IP: 192.168.188.253),
issue first (important!) 'fw_setenv' command and then perform regular
upgrade, using 'sysupgrade -n -F ...' (you can use 'wget' to download
image to the device, SSH server is not available):

  fw_setenv bootcmd "bootm 0x9f050000 || bootm 0x9fe80000"
  sysupgrade -n -F openwrt-...-yuncore_...-squashfs-sysupgrade.bin

In case your device runs firmware with YunCore custom GUI, you can use
U-Boot recovery mode:

1. Set a static IP 192.168.0.141/24 on PC and start TFTP server with
   'tftp' image renamed to 'upgrade.bin'
2. Power the device with reset button pressed and release it after 5-7
   seconds, recovery mode should start downloading image from server
   (unfortunately, there is no visible indication that recovery got
   enabled - in case of problems check TFTP server logs)

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2019-11-25 17:32:46 +01:00
Vincent Wiemann
8016f64864 ath79: add support for YunCore TFTP image generation
YunCore QCA9k based devices released in 2019 require a custom TFTP image
for U-Boot built-in recovery mode (triggered with reset button). Image
has to be prepended with 'YUNCORE' keyword followed by U-Boot CLI
commands which will be executed later. Images without the custom header
will be ignored by U-Boot.

To be able to support both the vendor firmware (QSDK) and OpenWrt flash
layouts, used here commands change the 'bootcmd' before flashing image.

This commit adds generic helper script for YunCore devices with 16 MB of
flash and enables TFTP image generation for A770 model.

Signed-off-by: Vincent Wiemann <vincent.wiemann@ironai.com>
[pepe2k@gmail.com: commit description reworded, recipe renamed]
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2019-11-25 17:32:46 +01:00
Piotr Dymacz
c543dfe431 ath79: generic: base-files: fix indentation in 02_network
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2019-11-25 17:32:46 +01:00
David Bauer
6a76ea359b ramips: reorganize NETGEAR sercomm boards
This re-organizes the device-tree files for the Sercomm-manufactured
NETGEAR routers. They are now split into two different base-boards,
from which the respective model is extended.

This partially reverts commit c7842ceaaa ("ramips: reorganize DTSI
files for Netgear R devices"), which introduced inheritance between two
completely unrelated base-boards.

Signed-off-by: David Bauer <mail@david-bauer.net>
2019-11-24 23:17:20 +01:00
Stijn Segers
bfabd8d613 ath79: remove ath10k drivers from Archer C7 v1 profile
Ath10k packages were removed from ar71xx in master in commit
34113999ef ("ar71xx: Remove ath10k packages from archer-c7-v1 (fixes
FS#1743)") but ath79 in master and the 19.07 branch still suffer from
the issue.

Signed-off-by: Stijn Segers <foss@volatilesystems.org>
[commit description facelift]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-11-24 14:19:43 +01:00
Petr Štetiar
3bbcffa0b6 treewide: kernel config: remove runtime options
Remove CC_HAS_ASM_GOTO, CC_IS_GCC and GCC_VERSION kernel config options
which are set at runtime and which should be ignored now.

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-11-24 14:19:43 +01:00
Yousong Zhou
b3779e920e kernel: nf_conntrack_rtcache: fix WARNING on rmmod
Fixes b7c58a1ee ("kernel: nf_conntrack_rtcache: fix cleanup on netns
delete and rmmod")

Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
2019-11-23 18:07:14 +00:00
Yousong Zhou
1c5df850a0 kernel: nf_conntrack_rtcache: fix WARNING on forward path
Fixes b7c58a1ee ("kernel: nf_conntrack_rtcache: fix cleanup on netns
delete and rmmod")

Resolves FS#2624

Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
2019-11-23 17:28:32 +00:00
Adrian Schmutzler
226bc91109 ath79: improve TP-Link CPE DTSI names for ar9344 SOC
The initial DTSI names for the TP-Link CPE devices have become
quite confusing, as several non-V1 devices now use the *-v1.dtsi,
the *cpe510-v1.dts does not use the cpe510.dtsi, etc.

This introduces a new naming scheme based on whether devices have
one or two ports, which should be easier to grasp.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-11-23 12:03:49 +01:00
Adrian Schmutzler
640a36aafc ath79: DTS style improvement for Ubiquiti XM and BZ devices
This applies minor style improvements and removes commented pll
clock adjustments from ubnt_xm DTSI. The latter were introduced
(already commented out) when adding ath79 target and have never
been touched since then. For Unifi (BZ board), similar clock
adjustments are employed and used.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-11-23 11:57:48 +01:00
Yousong Zhou
b7c58a1eeb kernel: nf_conntrack_rtcache: fix cleanup on netns delete and rmmod
Fixes FS#1472, FS#2353, FS#2426

Fixes: b3f95490 ("kernel: generic: Add kernel 4.14 support")
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
2019-11-23 10:47:51 +00:00
Hauke Mehrtens
103e49f62e kernel: Add missing configuration option
This was found by the build bot.

Fixes: e29500eb84 ("kernel: bump 4.19 to 4.19.85")
Fixes: db9e9e8382 ("kernel: bump 4.14 to 4.14.155")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2019-11-22 20:15:36 +01:00
Koen Vandeputte
ada7322055 cns3xxx: use proper macros for defining partition regions
While at it, also reorder the items for
improved readability.

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-11-22 16:56:46 +01:00
Koen Vandeputte
e29500eb84 kernel: bump 4.19 to 4.19.85
Refreshed all patches.

Altered patches:
- 080-sata_support.patch

Remove upstreamed:
- 034-v4.20-MIPS-BCM47XX-Enable-USB-power-on-Netgear-WNDR3400v3.patch
- 001-4.21-01-BCM63XX-fix-switch-core-reset-on-BCM6368.patch
- 073-qcom-ipq4019-fix-cpu0-s-qcom-saw2-reg-value.patch

Compile-tested on: cns3xxx
Runtime-tested on: cns3xxx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-11-22 16:56:46 +01:00
Koen Vandeputte
db9e9e8382 kernel: bump 4.14 to 4.14.155
Refreshed all patches.

Altered patches:
- 707-dpaa-ethernet-support-layerscape.patch

Remove upstreamed:
- 034-v4.20-MIPS-BCM47XX-Enable-USB-power-on-Netgear-WNDR3400v3.patch
- 001-4.21-01-BCM63XX-fix-switch-core-reset-on-BCM6368.patch
- 073-qcom-ipq4019-fix-cpu0-s-qcom-saw2-reg-value.patch

Compile-tested on: cns3xxx
Runtime-tested on: cns3xxx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-11-22 16:56:46 +01:00
Andrew Cameron
20fdfe37d2 ath79: add support for the TP-LINK WBS510 V1
This adds support for a popular low-cost 5GHz N based AP

Specifications:
- SoC: Atheros AR9344
- RAM: 64MB
- Storage: 8 MB SPI NOR
- Wireless: 5GHz 300 Mbps, 2x RP-SMA connector, 27 dBm TX power
- Ethernet: 1x 10/100 Mbps with 24V POE IN, 1x 10/100 Mbps

Installation:
Flash factory image through stock firmware WEB UI
or through TFTP
To get to TFTP recovery just hold reset button while powering on for
around 4-5 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP:192.168.0.100
Stock device TFTP adress:192.168.0.254

Signed-off-by: Andrew Cameron <apcameron@softhome.net>
2019-11-22 11:41:27 +01:00
Andrew Cameron
5b8709d9f2 ath79: add support for the TP-LINK WBS510 V2
This adds support for a popular low-cost 5GHz N based AP

Specifications:
 - SoC: Atheros AR9344
 - RAM: 64MB
 - Storage: 8 MB SPI NOR
 - Wireless: 5GHz 300 Mbps, 2x RP-SMA connector, 27 dBm TX power
 - Ethernet: 1x 10/100 Mbps with 24V POE IN, 1x 10/100 Mbps

Installation:
Flash factory image through stock firmware WEB UI
or through TFTP
To get to TFTP recovery just hold reset button while powering on for
around 4-5 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP:192.168.0.100
Stock device TFTP adress:192.168.0.254

Signed-off-by: Andrew Cameron <apcameron@softhome.net>
2019-11-22 11:41:24 +01:00
Lech Perczak
08d9c95417 ar71xx: ubnt-(xm,xw): add rssileds package
In order to make RSSI indicator on the device work out of box,
include "rssileds" package in per-device rootfs image by default
for Ubiquiti XM and XW devices, namely:
- Bullet M (XM/XW)
- Rocket M (XM/XW)
- Nanostation M (XM/XW)
- Nanostation Loco-M (XW)

This moves the package addition to the individual devices in order
to prevent accidental inclusions of the package when not looking
at the parent node carefully enough.

Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
[add bullet-m-xw, remove rocket-m-ti, extend commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-11-21 12:55:50 +01:00
Adrian Schmutzler
317e98a5a2 ath79: add PoE passthrough switch for Ubiquiti Nanostation (XM/XW)
This adds the gpio switch to enable PoE passthrough on Ubiquiti
Nanostation (XM/XW).

Values are copied from the implementation in ar71xx.

GPIO values checked on:
- NanoStation M5 XW
- NanoStation M2 XM

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-11-21 12:26:05 +01:00
Andre Heider
1f37b2226e omap: switch from uEnv.txt to generic distro booting
Which makes supporting different boot devices easy.

Signed-off-by: Andre Heider <a.heider@gmail.com>
2019-11-20 10:46:19 +01:00
Andre Heider
65cfe8164a omap: switch to kernel 4.19
Signed-off-by: Andre Heider <a.heider@gmail.com>
2019-11-20 10:46:19 +01:00
Andre Heider
e26b7e3c53 omap: enable new sound kernel options
This gets rid of a boot time warning about the missing edma module.
Enable SND_OMAP_SOC_HDMI_AUDIO while here.
All enabled options default to y.

Signed-off-by: Andre Heider <a.heider@gmail.com>
2019-11-20 10:46:19 +01:00
Andre Heider
124b2d32b5 omap: disable excess kernel debug options
Signed-off-by: Andre Heider <a.heider@gmail.com>
2019-11-20 10:46:19 +01:00
Andre Heider
65e6b7a4d8 omap: run make oldconfig for kernel 4.19
The only manually enabled config is the new OMAP4_DSS_HDMI_CEC, which
defaults to y.

Signed-off-by: Andre Heider <a.heider@gmail.com>
2019-11-20 10:46:19 +01:00
Andre Heider
26d05a3942 omap: copy the kernel 4.14 config for 4.19
Signed-off-by: Andre Heider <a.heider@gmail.com>
2019-11-20 10:46:19 +01:00
Koen Vandeputte
50ff887f41 ipq40xx: fix build error
Add missing brace which was accidentally omitted

Fixes: d6aea46a50 ("kernel: bump 4.14 to 4.14.154")
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-11-20 09:26:26 +01:00
Koen Vandeputte
723f4a4119 brcm2708: remove useless patches
The first adds some stuff while the second one
just reverts it.

Remove both patches.

This is done is a separate commit on purpose to make it clear.

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-11-20 08:00:44 +01:00
Koen Vandeputte
7533087565 kernel: bump 4.19 to 4.19.84
Refreshed all patches.

Altered patches:
- 950-0748-net-bcmgenet-Workaround-for-Pi-4B-network-issue.patch
- 950-0754-Revert-net-bcmgenet-Workaround-for-Pi-4B-network-iss.patch
- 902-debloat_proc.patch

Remove upstreamed:
- 150-MIPS-bmips-mark-exception-vectors-as-char-arrays.patch

New symbols:
X86_INTEL_MPX
X86_INTEL_MEMORY_PROTECTION_KEYS
X86_INTEL_TSX_MODE_OFF
X86_INTEL_TSX_MODE_ON
X86_INTEL_TSX_MODE_AUTO

Compile-tested on: cns3xxx, x86_64
Runtime-tested on: cns3xxx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-11-19 14:59:03 +01:00
Koen Vandeputte
d6aea46a50 kernel: bump 4.14 to 4.14.154
Refreshed all patches.

Altered patches:
- 902-debloat_proc.patch
- 040-dmaengine-qcom-bam-Process-multiple-pending-descript.patch
- 807-usb-support-layerscape.patch
- 809-flexcan-support-layerscape.patch
- 816-pcie-support-layerscape.patch

Remove upstreamed:
- 150-MIPS-bmips-mark-exception-vectors-as-char-arrays.patch
- 303-spi-nor-enable-4B-opcodes-for-mx66l51235l.patch

New symbols:
X86_INTEL_MPX
X86_INTEL_MEMORY_PROTECTION_KEYS
X86_INTEL_TSX_MODE_OFF
X86_INTEL_TSX_MODE_ON
X86_INTEL_TSX_MODE_AUTO
SGL_ALLOC

Compile-tested on: cns3xxx, x86_64
Runtime-tested on: cns3xxx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-11-19 14:59:03 +01:00
Koen Vandeputte
d2ee922051 kernel: bump 4.9 to 4.9.202
Refreshed all patches.

Altered patches:
- 902-debloat_proc.patch

Compile-tested on: none
Runtime-tested on: none

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-11-19 14:59:03 +01:00
Adrian Schmutzler
25127f58b4 ar71xx: fix buttons for TP-Link TL-WDR4900 v2
TP-Link TL-WDR4900 v2 only has one combined WPS/Reset button, so
don't set up an RFKILL for this device.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-11-19 12:52:17 +01:00
Adrian Schmutzler
93f2bcc35e ar71xx: fix LED setup for TL-WDR4900 v2
In ar71xx there is only one combined mach file for Archer C5/C7 and
TL-WDR4900 v2. This one uses the same LED struct for all devices,
defining "green" LEDs for them. However, WDR4900 uses blue front
LEDs, while only C5/C7 uses green ones. Despite, in base-files
WDR4900 is actually set up with "blue" for the mentioned LEDs.

Thus, this patch creates a separate LED struct for WDR4900, so the
LEDs can be set up correctly. Despite, the wlan5g LED is removed as
it is controlled by ath9k chip for WDR4900 (in contrast to C5/C7).

Note: While front LEDs are blue, USB LEDs (on the back) are green,
so colors are mixed intentionally for the WDR4900 v2.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-11-19 12:45:13 +01:00
Adrian Schmutzler
1a0d6e1eba ath79: fix DTS node names for Ubiquiti XM partitions
Some node names were inconsistent with the reg property. Fix it.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-11-19 00:16:48 +01:00
John Crispin
567d08104e mediatek: pass console inside bootargs on mt7629
Signed-off-by: John Crispin <john@phrozen.org>
2019-11-17 18:13:28 +01:00
John Crispin
d4f1937a21 mediatek: drop leading + from config
Signed-off-by: John Crispin <john@phrozen.org>
2019-11-17 18:12:08 +01:00
Sungbo Eo
19800ac095 ramips: set uImage name of WeVO 11AC NAS and W2914NS v2
The stock firmware and bootloader only accept uImage with names that
match certain patterns. This patch enables OpenWrt installation from
stock firmware without having to reflash the bootloader or access the
UART console.

Installation via web interface:
1.  Flash **initramfs** image through the stock web interface.
2.  Boot into OpenWrt and perform sysupgrade with sysupgrade image.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2019-11-17 14:01:31 +01:00
Adrian Schmutzler
a9d3084b83 ar71xx: fix MAC address setup for TL-WDR4900 v2
The MAC address setup of the TL-WDR4900 v2 is different from the
C5/C7. This aligns ar71xx with the setup in ath79:

wlan0 (5GHz) : -2
wlan1 (2.4GHz) : -1
eth1 (LAN) : 0
eth0 (WAN) : 1

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-11-17 13:06:31 +01:00
Christian Lamparter
7a7610c21b ath79: remap D-Link DIR-859 A1 WPS button to WPS
The WPS button was mapped to the restart/reset. This patch
changes it to emit the KEY_WPS_BUTTON keycode so pressing
the WPS button does initiate WPS.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-11-16 22:42:07 +01:00
Christian Lamparter
ad65d9d7b2 ramips: assign correct key-code to wps buttons
The ASUS WL-330N(3G) and the Edimax RG21S had the
reset keycode assigned to the WPS button. This patch
changes all three devices to use KEY_WPS_BUTTON in
the hopes that this fixes unwanted restarts/
unexpected behavior from the users point of view.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-11-16 22:37:51 +01:00
Jeff Kletsky
f84d6d2f3a ath79: fix firmware partition attributes for GL-AR300M16 and -Lite
During the introduction of the ath79/nand images for the GL-AR300M
series the firmware partition label and compatible were altered,
but the necessary adjustments have not been made for the
GL-AR300M16 and the GL-AR300M-Lite. This will result in a
non-bootable partition setup for these devices.

This patch adds the necessary definitions to those two devices.

Fixes: 55e6c903ae ("ath79: GL-AR300M: provide NAND support;
       increase to 4 MB kernel")
Fixes: b591cabd39 ("ath79: add GL.iNet GL-AR300M16 as NOR-only
       board")

Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
[extend commit message, alter commit title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-11-16 02:41:13 +01:00
John Crispin
1ea22e4de6 mediatek: drop accidentially commited file
Signed-off-by: John Crispin <john@phrozen.org>
2019-11-15 07:52:57 +01:00
John Crispin
50735df7b2 mediatek: fix bootup problem on mt7629 EVB
Signed-off-by: John Crispin <john@phrozen.org>
2019-11-15 07:51:32 +01:00
Adrian Schmutzler
fc44a8481c ath79: fix sysupgrade from ar71xx for WNDR3700 V2 and WNDR3800(CH)
ar71xx has just one board name "wndr3700" for WNDR3700 V1/V2,
WNDR3800 and WNDR3800CH, whereas ath79 provides separate images for
the boards. So, update SUPPORTED_DEVICES to store the correct
ar71xx board names.

Fixes: FS#2510

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-11-14 23:14:35 +01:00
Paul Blazejowski
7e623c3128 ath79: add support for Netgear WNDR3700v4
This patch adds ath79 support for Netgear WNDR3700v4.
Router was previously supported by ar71xx target only.
Note: device requires 'ar934x-nand' driver in kernel.

Specification
=============
  * Description: Netgear WNDR3700v4
  * Loader: U-boot
  * SOC: Atheros AR9344 (560 MHz)
  * RAM: 128 MiB
  * Flash: 128 MiB (NAND)
    - U-boot binary: 256 KiB
    - U-boot environment: 256 KiB
    - ART: 256 KiB
    - POT: 512 KiB
    - Language: 2 MiB
    - Config: 512 KiB
    - Traffic Meter: 3 MiB
    - Firmware: 25 MiB
    - ART Backup: 256 KiB
    - Reserved: 96 MiB
  * Ethernet: 5 x 10/100/1000 (4 x LAN, 1 x WAN) (AR8327)
  * Wireless:
    - 2.4 GHz b/g/n (internal)
    - 5 GHz a/n (AR9580)
  * USB: yes, 1 x USB 2.0
  * Buttons:
    - Reset
    - WiFi (rfkill)
    - WPS
  * LEDs:
    - Power (amber/green)
    - WAN (amber/green)
    - WLAN 2G (green)
    - WLAN 5G (blue)
    - 4 x LAN (amber/green)
    - USB (green)
    - WPS (amber/green)
  * UART: 4-pin connector JP1, 3.3V (Vcc, TX, RX, GND), 115200 8N1
  * Power supply: DC 12V 2.5A
  * MAC addresses: LAN=WLAN2G on case label, WAN +1, WLAN5G +2

Installation
============
  * TFTP recovery
  * TFTP via U-boot prompt
  * sysupgrade
  * Web interface

Note about partitioning: firmware partition offset (0x6c0000) is
hardcoded into vendor's u-boot, so this partition cannot be moved
and resized to include Netgear-specific flash areas (pot, language,
config, traffic_meter) not used by OpenWrt.

Test build configuration
========================
CONFIG_TARGET_ath79=y
CONFIG_TARGET_ath79_nand=y
CONFIG_TARGET_ath79_nand_DEVICE_netgear_wndr3700-v4=y
CONFIG_ALL_KMODS=y
CONFIG_DEVEL=y
CONFIG_CCACHE=y
CONFIG_COLLECT_KERNEL_DEBUG=y
CONFIG_IMAGEOPT=y

Signed-off-by: Paul Blazejowski <paulb@blazebox.homeip.net>
2019-11-14 23:14:15 +01:00
Michal Cieslakiewicz
119e0d57ae ath79: split dts file for Netgear WNDR4300
Move board configuration to dtsi file in preparation for WNDR3700v4
router support.

Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
2019-11-14 23:13:49 +01:00
Adrian Schmutzler
71fbec0eff ath79: fix indent in TP-Link TL-WDR4900 v2 DTS
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-11-14 23:13:19 +01:00
Adrian Schmutzler
bcee364944 ath79: improve common DTSI name for TP-Link Archer C5, C7 v1/v2
As the former qca9558_tplink_archer-c7.dtsi is also used for
Archer C5 v1 this patch removes the number from the DTSI name
to indicate that.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-11-14 23:12:48 +01:00
Petr Štetiar
fa83455392 ath79: remove obsolete OF PCI related config symbols
Those symbols were removed in kernel 4.16:

 commit 4670d610d59233b017a6ea1fa25bbf06dabbff42
 Author:     Rob Herring <robh@kernel.org>

    PCI: Move OF-related PCI functions into PCI core

Fixes: FS#2588
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-11-14 22:53:31 +01:00
Roger Pueyo Centelles
1c6066a867 ath79: include rssileds package for ubnt devices with LEDs
Some Ubiquiti devices had the RSSI LEDs configured in 01_leds but
were missing the rssileds package, while others that don't have
RSSI LEDS had the package included.

This commit includes the rssileds package only for those devices
that need it.

Tested on a NanoStation M XW.

Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
2019-11-14 16:03:33 +01:00
Jeff Kletsky
b496a2294c ath79: GL-AR750S: provide NAND support; increase kernel to 4 MB
The GL.iNet GL-AR750S has been supported by the ar71xx and ath79
platforms with access to its 16 MB NOR flash, but not its 128 MB
SPI NAND flash.

This commit provides support for the NAND through the upstream
SPI-NAND framework.

At this time, the OEM U-Boot appears to only support loading the
kernel from NOR. This configuration is preserved as this time,
with the glinet,gl-ar750s-nand name reserved for a potential,
future, NAND-only boot.

The family of GL-AR750S devices on the ath79 platform now includes:

  * glinet,gl-ar750m-nor-nand   "nand" target
  * glinet,gl-ar750m-nor        "nand" target (NAND-aware)

NB: This commit increases the kernel size from 2 MB to 4 MB

"Force-less" sysupgrade is presently supported from the current
versions of following NOR-based firmwre images to the version of
glinet,gl-ar750s-nor firmware produced by this commit:

  * glinet,gl-ar750s     -- OpenWrt 19.07 ar71xx
  * glinet,gl-ar750s     -- OpenWrt 19.07 ath79

Users who have sucessfully upgraded to glinet,gl-ar750m-nor may then
flash glinet,gl-ar750m-nor-nand with sysupgrade to transtion to the
NAND-based variant.

Other upgrades to these images, including directly to the NAND-based
glinet,gl-ar750s-nor-nand firmware, can be accomplished through U-Boot.

NB: See "ath79: restrict GL-AR750S kernel build-size to 2 MB" which
enables flashing of NAND factory.img with the current GL-iNet U-Boot,
"U-Boot 1.1.4-gcf378d80-dirty (Aug 16 2018 - 07:51:15)"

The GL-AR750S OEM U-Boot allows upload and flashing of either NOR
firmware (sysupgrade.bin) or NAND firmware (factory.img) through its
HTTP-based GUI. Serial connectivity is not required.

The glinet,gl-ar750s-nor and glinet,gl-ar750s-nor-nand images
generated after this commit flash each other directly.

This commit changes the control of the USB VBUS to gpio-hog from
regulator-fixed introduced by commit 0f6b944c92. This reduces the
compressed kernel size by ~14 kB, with no apparent loss of
functionality. No other ath79-nand boards are using regulator-fixed
at this time.

Note: mtd_get_mac_binary art 0x5006 does not return the proper MAC
and the GL.iNet source indicates that only the 0x0 offset is valid

The ar71xx targets are unmodified.

Cc: Alexander Wördekemper <alexwoerde@web.de>

Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
2019-11-14 14:38:58 +08:00
Jeff Kletsky
b591cabd39 ath79: add GL.iNet GL-AR300M16 as NOR-only board
The GL.iNet GL-AR300M series of devices includes variants without NAND
and only the 16 MB NOR flash. These include the GL-AR300M16 and the
GL-AR300M-Lite (already with its own board name).

This board-name addition provides disambiguation from the NAND-bearing
GL-AR300M devices, both for OpenWrt code and for end users.

Kernel and firmware support for NAND and UBI will add ~320 kB to the
overall firmware size at this time. This NOR-only option continues to
provide more compact firmware for both the GL-AR300M16 as well as
those who wish to use it as an alternate or primary, NOR-resident
firmware on the GL-AR300M.

The ar71xx targets are unmodified.

Installation
------------

Install through OEM U-Boot (HTTP-based) or `sysupgrade --force` when
booted from NOR and running OEM or OpenWrt, NOR-based firmware.

As one of the intentions is disambiguation from NAND-bearing units,
users who have flashed this firmware onto a device with NAND would
need to use U-Boot or `sysupgrade --force` to flash firmware that
again supports NAND.

There are no additional SUPPORTED_DEVICES as it is not possible to
determine if a device does or does not have NAND based on
either the OEM's or OpenWrt's board names prior to this patch.

Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
2019-11-14 14:38:58 +08:00