This adds the device tree changes needed to make the GMAC stmmac driver
working for the Allwinner H3 SoCs.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This adds the device tree changes needed to make the GMAC stmmac driver
working for the Allwinner A64 SoCs.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This adds support for the GMAC which is use in the A64 and other
Allwinner chips by backporting the changes from the kernel versions
4.13.
Some commits are not backported which are adding support for newly
introduced APIs which are not available in kernel 4.9.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This updates mac80211 to backprots-4.14-rc2.
This was compile and runtime tested with ath9k, ath10k and b43
with multiple stations and ieee80211w and in different scenarios by many
other people.
To create the backports-4.14-rc2-1.tar.xz use this repository:
https://git.kernel.org/pub/scm/linux/kernel/git/backports/backports.git
from tag v4.14-rc2-1
Then run this:
./gentree.py --git-revision v4.14-rc2 --clean <path to linux repo> ../backports-4.14-rc2-1
This also adapts the ath10k-ct and mt76 driver to the changed cfg80211
APIs and syncs the nl80211.h file in iw with the new version from
backports-4.14-rc2.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The /bin/config_generate script and some other scripts are assuming the
/etc/config directory exists in the image. This is true in case for
example the package firewall, dropbear or dnsmasq are included, which
are adding the files under /etc/config/. Without any of these package
the system will not boot up fully because the /etc/config/ directory is
missing and some init scripts just fail.
Make sure all images with the base-files contain a /etc/config/
directory.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: John Crispin <john@phrozen.org>
This reverts commit b428f45c06.
If the optimized firmware download is disabled, the xdsl subsystem
hangs in the "idle request" state after physically disconnecting and
reconnecting the xdsl modem from the line.
It might fix the failing line init on boot as well.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The empty version.sh script causes a problem when run by make:
make[3]: /usr/bin/env bash: Shell program not found
Adding a shebang line in version.sh seems to solve it.
Fixes FS#977.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
getrandom blocks until the random pool is being initialized.
Unfortunately, this code is being called early during init to create the
overlay filesystem, on some devices leaving little chance for a
successful random pool init.
True randomness is not that important here, so fix this issue by
sticking to using /dev/urandom, like in older versions of this code.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add -static-libstdc++ to TARGET_LDFLAGS to avoid a hard dependency on
libstdc++, and -Wl,--gc-sections to further reduce the size on platforms
that support it.
Fixes CVE-2017-9778.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
This is useful for tuning some more exotic parameters where it doesn't
make sense to attempt to cover everything in uci directly
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Booting from jffs2 directly is no longer supported, use
rootfstype=squashfs consistently for all subtargets
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Adds config option to enable compression support which is usefull
when using a terminal sessions over a slow link. Impact on binary
size is negligible but additional 60 kB (uncompressed) is needed for
a shared zlib library.
Signed-off-by: Marcin Jurkowski <marcin1j@gmail.com>
b84fdac Add debug output for service_timeout
8f7e3bc Remove incorrect comma in http service json config
9f40133 Remove ttl==255 restriction for queries
Signed-off-by: John Crispin <john@phrozen.org>
ee582d1 instance: properly compare and reload respawn config
260a4cd utrace: Start the tracee only after uloop initialization
520ad3c utrace: Switch all logging to ulog
1c48104 utrace: Support non-contiguous syscall numbers
582cf97 utrace: Forward SIGTERM to the traced process
32534f7 utrace: Report ptrace errors
ccde3fb seccomp: Improve error message
7f9b174 preload-seccomp: Use proper log level for error messages
e3c4302 Start seccomp-enabled services via seccomp-trace
5e4ad02 seccomp: Log seccomp violations with utrace
2661b2f utrace: Use PTHREAD_SEIZE instead of PTHREAD_TRACEME
b5d53c6 utrace: Deliver signals to traced processes
b416ed9 utrace: Support tracing multi-threaded processes and vfork
8b7d47a utrace: Trace processes across forks
c6b6ec6 utrace: Sort syscalls by number of invocations
592c532 Update trace attribute
c8faedc Do not disable seccomp when configuration is not found
017f3a1 utrace: Fix off-by-one errors
5acaf15 utrace: Fix environment initialization
Signed-off-by: John Crispin <john@phrozen.org>
This commit improves support for the Xiaomi Mi Router 3G originally
added in commit 6e283cdc0d
Improvements:
- Remove software watchdog as hardware watchdog now working as per
commit 3fbf3ab44f for all mt7621
devices.
- Reset button polarity corrected - length of press determines reboot
(short press) vs. reset to defaults (long press) behaviour.
- Enable GPIO amber switch port LEDs on board rear - lit indicates 1Gbit
link and blink on activity. Green LEDs driven directly by switch
indicating any link speed and tx activity.
- USB port power on/off GPIO exposed as 'usbpower'
- Add access to uboot environment settings for checking/setting uboot
boot order preference from user space.
Changes:
- Front LED indicator is physically made of independent Yellow/Amber,
Red & Blue LEDs combined via a plastic 'lightpipe' to a front panel
indicator, hence the colour behaviour is similar to an RGB LED. RGB
LEDs are not supported at this time because they produce colour results
that do not then match colour labels, e.g. enabling 'mir3g:red' and
'mir3g:blue' would result in a purple indicator and we have no such
label for purple.
The yellow, red & blue LEDs have been split out as individual yellow,
red & blue status LEDs, with yellow being the default status LED as
before and with red's WAN and blue's USB default associations removed.
- Swapped order of vlan interfaces (eth0.1 & eth0.2) to match stock vlan
layout. eth0.1 is LAN, eth0.2 is WAN
- Add 'lwlll' vlan layout to mt7530 switch driver to prevent packet
leakage between kernel switch init and uci swconfig
uboot behaviour & system 'recovery'
uboot expects to find bootable kernels at nand addresses 0x200000 &
0x600000 known by uboot as "system 1" and "system 2" respectively.
uboot chooses which system to hand control to based on 3 environment
variables: flag_last_success, flag_try_sys1_failed & flag_try_sys2_failed
last_success represents a preference for a particular system and is set
to 0 for system 1, set to 1 for system 2. last_success is considered *if*
and only if both try_sys'n'_failed flags are 0 (ie. unset) If *either*
failed flags are set then uboot will attempt to hand control to the
non failed system. If both failed flags are set then uboot will check
the uImage CRC of system 1 and hand control to it if ok. If the uImage
CRC of system is not ok, uboot will hand control to system 2
irrespective of system 2's uImage CRC.
NOTE: uboot only ever sets failed flags, it *never* clears them. uboot
sets a system's failed flag if that system's was selected for boot but
the uImage CRC is incorrect.
Fortunately with serial console access, uboot provides the ability to
boot an initramfs image transferred via tftp, similarly an image may
be flashed to nand however it will flash to *both* kernels so a backup
of stock kernel image is suggested. Note that the suggested install
procedure below set's system 1's failed flag (stock) thus uboot ignores
the last_success preference and boots LEDE located in system 2.
Considerable thought has gone into whether LEDE should replace both
kernels, only one (and which one) etc. LEDE kernels do not include a
minimal rootfs and thus unlike the stock kernel cannot include a
method of controlling uboot environment variables in the event of
rootfs mount failure. Similarly uboot fails to provide an external
mechanism for indicating boot system failure.
Installation - from stock.
Installation through telnet/ssh:
- copy lede-ramips-mt7621-mir3g-squashfs-kernel1.bin and
lede-ramips-mt7621-mir3g-squashfs-rootfs0.bin to usb disk or wget it
from LEDE download site to /tmp
- switch to /extdisks/sda1/ (if copied to USB drive) or to /tmp if
wgetted from LEDE download site
- run: mtd write lede-ramips-mt7621-mir3g-squashfs-kernel1.bin kernel1
- run: mtd write lede-ramips-mt7621-mir3g-squashfs-rootfs0.bin rootfs0
- run: nvram set flag_try_sys1_failed=1
- run: nvram commit
- run: reboot
Recovery - to stock.
Assuming you used the above installation instructions you will have a
stock kernel image in system 1. If it can be booted then it may be used
to perform a stock firmware recovery, thus erasing LEDE completely. From
a 'working' LEDE state (even failsafe)
Failsafe only:
- run: mount_root
- run: sh /etc/uci-defaults/30_uboot-envtools
Then do the steps for 'All'
All:
- run: fw_setenv flag_try_sys2_failed 1
- run: reboot
The board will reboot into system 1 (stock basic kernel) and wait with
system red light slowly blinking for a FAT formatted usb stick with a
recovery image to be inserted. Press and hold the reset button for
around 1 second. Status LED will turn yellow during recovery and blue
when recovery complete.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
The RT5350F's second UART pins are available on the base module and on
the EVB as well, so enable it in the device tree.
In order to keep the origian serial port numbering (ttyS0 is the serial
console), aliases added for the UART devices.
Signed-off-by: Zoltan Gyarmati <mr.zoltan.gyarmati@gmail.com>
The RT5350F i2c pins is available on the base module and on
the EVB as well, so enable it in the dts.
Signed-off-by: Zoltan Gyarmati <mr.zoltan.gyarmati@gmail.com>
The polarity of WLAN_ACT LED on the base module needs to inverted
in order to be 'on' when the WiFi interface is active
Signed-off-by: Zoltan Gyarmati <mr.zoltan.gyarmati@gmail.com>
The RT5350F-OLINUXINO(-EVB).dts files' content are nearly the same, so to avoid
code duplication this patch creates RT5350F-OLINUXINO.dtsi file which
covers the base board's features. The corresponding RT5350F-OLINUXINO.dts
just includes the new .dtsi and the RT5350F-OLINUXINO-EVB.dts adds the EVB
specific GPIO config.
Signed-off-by: Zoltan Gyarmati <mr.zoltan.gyarmati@gmail.com>
The Xiaomi Mi Router 3G uses this deranged vlan portmap. Add support so
that packets are not leaked across all switch ports when reset.
Fix a whitespace nit while we're here.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
[fix wrong pvids order]
Signed-off-by: Mathias Kresin <dev@kresin.me>
Disable VLANs on mt7621 boards with mt7530 switches on failsafe entry.
Allows failsafe networking to work correctly.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
[fixed default case syntax error]
Signed-off-by: Mathias Kresin <dev@kresin.me>
With ltq-vdsl-mei 1.5.17.6 an optimized firmware download was added and
enabled by default. As soon as the optimized firmware download is
enabled, a watchdog based reboot is trigger between 24h to 48h of
uptime if the board isn't connected to a xdsl line.
Signed-off-by: Mathias Kresin <dev@kresin.me>
This is a backport form drv_dsl_cpe_api-4.18.10 and fixes some PM
thread handling issues which lead to high system load and watchdog
trigger within 1h of uptime for boards not connected to a xdsl line.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Fixes CVE-2017-12166: out of bounds write in key-method 1.
Remove the mirror that was temporarily added during the
2.4.3 release.
Signed-off-by: Magnus Kroken <mkroken@gmail.com>
Update the config file to the latest version.
Added CONFIG_EAP_FAST=y because it was the only
missing flag about EAP compared to full config.
Removed NEED_80211_COMMON flag because it is not part
of config file, it is set by the hostapd upstream Makefile.
Other flags are the same as before.
Signed-off-by: Lorenzo Santina <lorenzo.santina@edu.unito.it>
[add punctuation to commit msg]
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Update the config file to the latest version.
Enabled flags are the same as before.
Removed NEED_80211_COMMON flag because it is not part
of config file, it is set by the hostapd upstream Makefile.
Signed-off-by: Lorenzo Santina <lorenzo.santina@edu.unito.it>
[add punctuation to commit msg]
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Update the config file to the latest version.
Enabled flags are the same as before.
Commented CONFIG_IEEE80211W=y flag because it is
set in the Makefile, only if the driver supports it.
Removed NEED_80211_COMMON flag because it is not part
of config file, it is set by the hostapd upstream Makefile.
Signed-off-by: Lorenzo Santina <lorenzo.santina@edu.unito.it>
[add punctuation to commit msg]
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Update the config file to the latest version.
Enabled flags are the same as before.
Signed-off-by: Lorenzo Santina <lorenzo.santina@edu.unito.it>
[add punctuation to commit msg]
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Update the config file to the latest version.
Enabled flags are the same as before.
Removed flag CONFIG_WPS2 because it is no more
needed due to this changelog (2014-06-04 - v2.2):
"remove WPS 1.0 only support, i.e., WSC 2.0
support is now enabled whenever CONFIG_WPS=y is set".
Signed-off-by: Lorenzo Santina <lorenzo.santina@edu.unito.it>
[add punctuation to commit msg]
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Bump to 7.55.1 broke the disable threaded resolver feature as reported
in https://github.com/curl/curl/issues/1784.
As a result curl is always compiled with the threaded resolver feature
enabled which causes a dependency issue on pthread for uclibc.
Fix this issue by backporting the upstream curl commit which fixes
disable threaded resolver.
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
This reverts commit 31e9445b7e.
"Linksys E1200 V1" is not a valid board name, as the brcm47xx arch code
can not detect this device. Stefan Lippers-Hollmann also found a typo in
this patch "cybetran" instead of "cybertan".
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Fixes the following build issue: "undefined reference to `EVP_MD_CTX_create'"
From: Jelle van der Waa <jelle@vdwaa.nl>
The rsa_st struct has been made opaque in 1.1.x, add forward compatible
code to access the n, e, d members of rsa_struct.
EVP_MD_CTX_cleanup has been removed in 1.1.x and EVP_MD_CTX_reset should be
called to reinitialise an already created structure.
Signed-off-by: Marko Ratkaj <marko.ratkaj@sartura.hr>
