Re-enable the Aruba AP-365 with DSA support. Changes are trvivial, as
the board design is pretty much the already updated AP-303.
Run-tested on the device.
Signed-off-by: David Bauer <mail@david-bauer.net>
Import commit "ubi: Fix failure attaching when vid_hdr offset equals to
(sub)page size" which did not yet make it to stable upstream Linux trees.
Fixes: #12232Fixes: #12339
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Updating to U-Boot 2023.04 broke the build for the RAVPower RP-WD009
MT7628 board. This was due to upstream conversion of CONFIG_* to CFG_*
which was not applied to our downstream patch adding support for the
RAVPower RP-WD009 device.
Apply CONFIG_* to CFG_* converion analog to what has been done also
for mt7928_rfb upstream.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Now that new pinconf features have been backported sync pinctrl-mt7981
and pinctrl-m7986 with bleeding-edge upstream versions.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Backport new features for MediaTek pinctrl/pinconf drivers from upstream.
This will serve as the base to improve pinconf bias/pull-up/pull-down on
MT7981 and MT7986, and also prepare for upcoming support for MT7988.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Avoid MCU getting "command reply receive timed out" message when LED
configuration setting trigger function is enabled in heartbeat mode.
Signed-off-by: Ian Chang <ianchang@ieiworld.com>
Update to next U-Boot timed release.
Remove now obsolete patch
100-01-board-mediatek-add-more-network-configurations.patch
Default IP addresses are now dealt with in Kconfig, no longer in board-
specific C header files.
Add patches to restore ANSI support in bootmenu which was broken upstream,
always use high-speed mode on serial UART for improved stability and fix
an issue with pinconf not being applied on MT7623 resulting in eMMC
being inaccessible when booting from micro SD card.
In order to keep the size of the bootloader on MT7623 below 512kB remove
some unneeded commands on both MT7623 boards.
Tested on:
* BananaPi BPi-R2 (MT7623N)
* BananaPi BPi-R3 (MT7986A)
* BananaPi BPi-R64 (MT7622A)
* Linksys E8450 (MT7622B)
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This is a silent command that allows easy wifi up/down automation for
scripts.
It takes one or multiple devices as arguments (or all if none are passed),
and the exit code indicates if any of those is not up.
E.g.:
wifi isup && echo "all wifi devices are up"
wifi isup radio0 || echo "this wifi is down"
Signed-off-by: Andre Heider <a.heider@gmail.com>
Use the already present but unused $cmd and $dev variables instead of
positional parameters in ubus_wifi_cmd() to improve readability.
Signed-off-by: Andre Heider <a.heider@gmail.com>
Synchronize the ath11k backports with the current ath-next tree.
This replaces the management TLV pending fix with the upstreamed one,
fixes traffic flooding when AP and monitor modes are used at the same time,
fixes QCN9074 always showing -95 dBm for station RSSI in dumps,
fixes potential crash on boot if spectral scan is enabled due to writing to
unitialized memory and adds 11d scan offloading for WCN6750 and WCN6855.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Refresh multiple lzma configuration option patch with new version
proposed upstream. (Reintroduce -Xe option and add more checks and
general better code quality)
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
This reverts commit a33b97dcb1.
A new version of the squashfs4 tool patch reintroduced the -Xe option.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Currently, during initialization ath11k will receive a regulatory event
from the firmware in which it will receive the default regulatory domain
code and accompanying rules list and report those to the kernel.
Then if you try to change the regulatory domain to a different country code
it will do a weird thing in which it will send that to the FW and after
receiving the appropriate regulatory event it will parse the rules.
However, while its parsing there is a weird thing being done, and that is
that new raw rules from FW get intersected with the rules from the default
domain.
This is creating a big issue as the default domain is almost always set to
"US" or just "00" aka world so ath11k will unfairly limit you to the most
restrictive combination of rules based on the default domain and your
desired domain.
For example, in ETSI countries this is causing channels 12 and 13 on 2.4GHz
to not be usable since "US" limits 2.4GHz to 2472MHz instead of 2482MHz
like ETSI countries do.
So, lets do what TIP and even QCA do in their ath11k downstream tree and
completely get rid of the interesection code in ath11k.
Signed-off-by: Robert Marko <robimarko@gmail.com>
When using "ubiformat" with stdin it requires passing image size using
the -S argument. Provide it just like we do for "ubiupdatevol".
This fixes:
ubiformat: error!: must use '-S' with non-zero value when reading from stdin
This change fixes sysupgrade for bcm53xx and bcm4908 NAND devices
possibly some other targets too.
Cc: Rodrigo Balerdi <lanchon@gmail.com>
Cc: Daniel Golle <daniel@makrotopia.org>
Fixes: 9710712120 ("base-files: accept gzipped nand sysupgrade images")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Daniel Golle <daniel@makrotopia.org>
Tested-by: Koen Vandeputte <koen.vandeputte@citymesh.com>
It appears that the refactor of the upgrade process for NAND devices resulted in the nand_do_upgrade_success step not being called for
devices using the linksys.sh script. As a result, configuration was
not preserved over sysupgrade steps.
This corrects a typo in the call of nand_do_upgrade_failed for ipq40xx
and ipq806x devices using the linksys.sh script.
Fixes: 8634c1080d ("ipq40xx: Fix Linksys upgrade, restore config step")
Fixes: 2715aff5df ("ipq806x: Fix Linksys upgrade, restore config step")
Signed-off-by: Michael Trinidad <trinidude4@hotmail.com>
It appears that the refactor of the upgrade process for NAND devices resulted in the nand_do_upgrade_success step not being called for
devices using the linksys.sh script. As a result, configuration was
not preserved over sysupgrade steps.
This restores the preservation of configs for mvebu/cortexa9 devices using the
linksys.sh script.
Fixes: e25e6d8e54 ("base-files: fix and clean up nand sysupgrade code")
Signed-off-by: Michael Trinidad <trinidude4@hotmail.com>
It appears that the refactor of the upgrade process for NAND devices
resulted in the nand_do_upgrade_success step not being called for
devices using the linksys.sh script. As a result, configuration was
not preserved over sysupgrade steps.
This restores the preservation of configs for kirkwood devices using the
linksys.sh script.
Fixes: e25e6d8e54 ("base-files: fix and clean up nand sysupgrade code")
Fixes: #12298
Signed-off-by: Michael Trinidad <trinidude4@hotmail.com>
Getting ready for the next release.
Signed-off-by: Paul Spooren <mail@aparcar.org>
[rmilecki: tested on GT-AC5300: boot, sysupgrade & 940 Mbps NAT]
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
bmips target is now more stable and it's time to start generating buildbot
images in order to receive a wider testing, which will be essential to replace
bcm63xx target in the future.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
BMIPS is a generic arch that can be used for multiple Broadcom SoCs, each one
with its own specific drivers, so instead of having a huge kernel supporting
all of them, let's switch to a subtarget per SoC like other OpenWrt targets.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
CRYPTO_USER_API_ENABLE_OBSOLETE config symbol depends on CRYPTO_USER so
lets add this dependency to relevant modules.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
While tracking one bug report related to wrong package dependencies I've
noticed, that a bunch of the crypto modules are actually not
architecture specific, but either board/subtarget (x86/64) or board
(mpc85xx) specific.
So lets fix it, by making those modules architecture specific:
x86/64 -> x86_64
mpc85xx -> powerpc
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Add BCM6328 and BCM6358 LED kernel modules.
This allows selecting the LED controllers only for those devices using them.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Sercomm SHG2500 is a BCM63168 with 128M of RAM, 256M of NAND, an external
BCM53124S switch for the LAN ports and internal/external Broadcom wifi.
LEDs are connected to an external MSP430G2513 MCU controlled via SPI.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Make use of sercomm-pid script for generating the Sercomm PID, which avoids
having to add an array of hex bytes for every new Sercomm device.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SERCOMM_VERSION is ambiguous and it should be more clear that it refers to the
version used for the filesystem.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Apparently, Sercomm sets 2 padding bytes instead of 1 (ramips).
The HW version is a bit different than the one used for ramips.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Instead of passing an array of hex bytes for the Sercomm PID we can now use
the --pid-file parameter.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Allow passing Sercomm PID from file.
Until now, Sercomm PID could only be passed as an array of hex bytes.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
