ipTIME AX2004M is an 802.11ax (Wi-Fi 6) router, based on MediaTek
MT7621A.
Specifications:
* SoC: MT7621A
* RAM: 256 MiB
* Flash: NAND 128 MiB
* Wi-Fi:
* MT7915D: 2.4/5 GHz (DBDC)
* Ethernet: 5x 1GbE
* Switch: SoC built-in
* USB: 1x 3.0
* UART: J4 (115200 baud)
* Pinout: [3V3] (TXD) (RXD) (GND)
MAC addresses:
| interface | MAC address | source | comment
|-----------|-------------------|----------------|---------
| LAN | 58:xx:xx:00:xx:9B | | [1]
| WAN | 58:xx:xx:00:xx:99 | |
| WLAN 2G | 58:xx:xx:00:xx:98 | factory 0x4 |
| WLAN 5G | 5A:xx:xx:40:xx:98 | |
| | 58:xx:xx:00:xx:98 | config ethaddr |
[1] Used in this patch as WLAN 5G MAC address with the local bit set
Load addresses:
* stock
* 0x80010000: FIT image
* 0x81001000: kernel image -> entry
* OpenWrt
* 0x80010000: FIT image
* 0x82000000: uncompressed kernel+relocate image
* 0x80001000: relocated kernel image -> entry
Notes:
* This device has a dual-boot partition scheme, but this firmware works
only on boot partition 1. The stock web interface will flash only on the
inactive boot partition, but the recovery web page will always flash on
boot partition 1.
Installation via recovery mode:
1. Press reset button, power up the device, wait >10s for CPU LED
to stop blinking.
2. Upload recovery image through the recovery web page at 192.168.0.1.
Revert to stock firmware:
1. Install stock image via recovery mode.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
When using a non default MESON_HOST_BUILD_DIR, HOST_BUILD_DIR is not
appropriate to use. This change matches the target configure section.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Commit f4a79148f8 ("ramips: add support for ipTIME AX2004M") seems to
leak KERNEL_LOADADDR 0x82000000 to other devices, causing the to no
longer boot. The leak is visible in u-boot:
Using 'config-1' configuration
Trying 'kernel-1' kernel subimage
Description: MIPS OpenWrt Linux-5.10.92
Type: Kernel Image
Compression: lzma compressed
Data Start: 0x840000e4
Data Size: 10750165 Bytes = 10.3 MiB
Architecture: MIPS
OS: Linux
Load Address: 0x82000000
Entry Point: 0x82000000
Normally, it should look like this:
Using 'config-1' configuration
Trying 'kernel-1' kernel subimage
Description: MIPS OpenWrt Linux-5.10.92
Type: Kernel Image
Compression: lzma compressed
Data Start: 0xbfca00e4
Data Size: 2652547 Bytes = 2.5 MiB
Architecture: MIPS
OS: Linux
Load Address: 0x80001000
Entry Point: 0x80001000
Revert the commit to avoid more people soft-bricking their devices.
This reverts commit f4a79148f8.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
ipTIME NAS1 is a 1-bay NAS, based on Marvell Kirkwood SoC.
Specifications:
* SoC: 88F6281
* RAM: 256 MiB
* Flash: SPI NOR 16 MiB
* SATA: 1x 3Gb/s
* Ethernet: 1x 1GbE
* USB: 1x 2.0
* Fan: 2 speed level
* UART: JP1 (115200 8N1)
* Pinout: [3V3] (TXD) (RXD) (GND)
Notes:
* There are several variants of the model name: "NAS-I", "NASI", "NAS1".
Here "NAS1" is adopted for consistent naming scheme.
* The reset button is also a USB copy button in stock FW,
but in this patch the former is the only default behavior.
Installation via web interface:
1. Flash sysupgrade image through the stock web interface.
Revert to stock firmware:
1. Perform sysupgrade with stock image.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
This allows to implement statefull bridge filtering
As the uncompressed size is only 7.6k (arm64), just add
nf_conntrack_bridge.ko to kmod-nft-bridge package
Signed-off-by: Etienne Champetier <champetier.etienne@gmail.com>
On macOS, system binaries silently drop the environment variables for injecting
extra shared libraries (used by fakeroot). This is done for security reasons.
Work around this by building bash from source, so that it gets an ad-hoc signature
and does not have these restrictions
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Ubuntu started to flag which as deprecated and it
seems which is not really standard and may vary
across Distro.
Drop the use of which and use the standard 'command -v'
for this simple task.
Which is still present in the prereq if some package/script
still use which.
A utility script called command_all.sh is implemented that
will just mimic the output of which -a.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Added HOST_CXXFLAGS to specify CXXFLAGS during host-compile
(e.g. to specify c++ standard: HOST_CXXFLAGS += -std=c++11)
Signed-off-by: Sergey V. Lobanov <sergey@lobanov.in>
Move the kernel versions and hash to dedicated files.
This makes kernel bump quicker and fix some annoying
problem with rebasing when multiple kernel bump are proposed.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
[Rebased on top of current master]
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Add and enable a new kconfig knob to disable unprivileged eBPF by default.
Patches automatically rebased.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
All patches automatically rebased.
Build system: x86_64
Build-tested: ramips/mt7621*
*Had to revert 7f1edbd in order to build due to FS#4149
Signed-off-by: John Audia <graysky@archlinux.us>
This CPU type is compatible with NXP's PPC based QorIQ processors, and
will be used by the upcoming new qoriq target.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Reviewed-by: Rui Salvaterra <rsalvaterra@gmail.com>
All patches automatically rebased.
Build system: x86_64
Build-tested: bcm2711/RPi4B, ipq806x/R7800*
Run-tested: bcm2711/RPi4B, ipq806x/R7800*
*Had to revert 7f1edbd412 in order to build
(binutils 2.37, https://bugs.openwrt.org/index.php?do=details&task_id=4149)
Signed-off-by: John Audia <graysky@archlinux.us>
All patches automatically rebased.
Build system: x86_64
Build-tested: bcm2711/RPi4B, ipq806x/R7800*
Run-tested: bcm2711/RPi4B, ipq806x/R7800*
*Had to revert 7f1edbd412 in order to build
(binutils 2.37, https://bugs.openwrt.org/index.php?do=details&task_id=4149)
Signed-off-by: John Audia <graysky@archlinux.us>
Removed target for patch which does not exist:
bcm27xx/patches-5.10/950-0249-kbuild-Disable-gcc-plugins.patch
All patches automatically rebased.
Build system: x86_64
Build-tested: bcm2711/RPi4B, ipq806x/R7800*
Run-tested: bcm2711/RPi4B, ipq806x/R7800*
* Had to revert 7f1edbd412 in order to build
(binutils 2.37, https://bugs.openwrt.org/index.php?do=details&task_id=4149)
Signed-off-by: John Audia <graysky@archlinux.us>
All patches automatically rebased.
Build system: x86_64
Build-tested: ramips/mt7621*
*FS#4149 affects me so I had to revert 7f1edbd412
in order to downgrade to 2.35.1
Signed-off-by: John Audia <graysky@archlinux.us>
All patches automatically rebased.
Build system: x86_64
Build-tested: ramips/mt7621*
*FS#4149 affects me so I had to revert 7f1edbd412
in order to downgrade to 2.35.1
Signed-off-by: John Audia <graysky@archlinux.us>
All patches automatically rebased.
Build system: x86_64
Build-tested: ramips/mt7621*
*FS#4149 affects me so I had to revert 7f1edbd412
in order to downgrade to 2.35.1
Signed-off-by: John Audia <graysky@archlinux.us>
Added support to generate dynamic-sized VHDX images for Hyper-V.
Compile-tested on x86 and run-tested on Windows 10 21H2 (Hyper-V).
Signed-off-by: Oldřich Jedlička <oldium.pro@gmail.com>
change meson binary to use py extension. Fixes issue with meson's
symbolextractor using the host python instead of the system one.
We intentionally use a .py extension here so that meson launches
additional python scripts with the same build host python interpreter as
itself is running under (and not the host package one once it becomes
available)
Signed-off-by: Rosen Penev <rosenp@gmail.com>
CONFIG_EXTERNAL_CPIO is a string variable, hence testing for 'y'
doesn't make much sense here.
Fixes: 330bd380e8 ("image: allow building FIT and uImage with ramdisk")
Reported-by: Huangbin Zhan <zhanhb88@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Newer NAND devices from MikroTik like the hAP ac3
require the kernel to be packed into UBIFS and then
ubinized.
So, since the ubinize-image.sh script can now ubinize
kernel only as well lets add a command for it.
This now allows calling ubinize-kernel in the kernel
packaging at then end.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Rootfs is now optional in ubinize-image.sh and
requires --rootfs flag instead of just passing the
rootfs image as the argument before ubinize opts.
So, simply add --rootfs flag before the $(IMAGE_ROOTFS).
Signed-off-by: Robert Marko <robimarko@gmail.com>
All patches automatically rebased.
Build system: x86_64
Build-tested: ramips/mt7621*
*I am hit with the binutils 2.37 bug so I had to revert 7f1edbd412
in order to downgrade to 2.35.1
Signed-off-by: John Audia <graysky@archlinux.us>
Manually rebased:
generic-backport/850-v5.13-usb-ehci-add-spurious-flag-to-disable-overcurrent-ch.patch
All other patches automatically rebased.
Signed-off-by: John Audia <graysky@archlinux.us>
BTF pointer data has a different size on 32 vs 64 bit targets,
and while the generated eBPF code works, the BTF data fails to validate
on mismatch
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This allows a package to be rebuilt for all different VARIANTs.
To do so, set VARIANT=*.
The wpa-cli package is not getting built after changes made by
19aae94 [build: avoid rebuilds of unset VARIANT packages], because
wpa-cli is only built when compiling a variant that includes
supplicant support, and the first selected variant may not build it.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
Removed upstreamed:
backport-5.4/790-v5.7-net-switchdev-do-not-propagate-bridge-updates-across.patch
All other patches automatically rebased.
Signed-off-by: John Audia <graysky@archlinux.us>
When the prebuilt llvm toolchain is unpacked into the source dir,
it is automatically picked up and used by the build system, and eBPF
based packages can be selected
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The empty executable is causing problems with meson builds, due to the
error: OSError: [Errno 8] Exec format error: 'ldconfig'
This patch changes the empty ldconfig stub to symlink to /bin/true to
work around this issue.
Fixes: FS#4117
Fixes: 3bd31cc4d2 ("tools/meson: update to 0.60.0")
Signed-off-by: Damien Mascord <tusker@tusker.org>
Tested-by: Aleksander Jan Bajkowski <olek2@wp.pl> # Tested on Debian 11
Tested-By: Lucian Cristian <lucian.cristian@gmail.com>
Tested-By: Baptiste Jonglez <git@bitsofnetworks.org>
Cc: Rosen Penev <rosenp@gmail.com>
If a Makefile defines some packages with VARIANT set, and others without
it, the latter will be built once for every different VARIANT set, each
build trumping the previous one.
Avoid rebuilds by only building unnamed variant packages when the first
variant is built.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
The $(LINUX_DIR)/.config timesptamp changes between runs of
make target/compile and make target/install (which builds the image).
Kernel-dependent packages and out of tree modules are built in between
those runs, and they check the .config timestamp to decide if they need
to be rebuilt.
Save the target/compile .config to use its timestamp if the file does
not change between runs. That way the subsequent kernel packages are
not unnecessarily rebuilt when you run 'make' back to back.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
4e19cbc553: [download: handle possibly invalid local tarballs] added a
FORCE rule to downloaded files, so that they will be always checked by
download.pl.
As a side-effect, check-compile will fail, forcing unnecessary package
rebuilds.
The check-compile.txt log shows (for libxml2 for example):
Considering target file '.../dl/libxml2-2.9.12.tar.gz'.
...
prerequisite 'FORCE' of target '.../dl/libxml2-2.9.12.tar.gz' does
not exist.
Must remake target '.../dl/libxml2-2.9.12.tar.gz'.
...
Giving up on target file '...libxml2-2.9.12/.prepared_...'.
Giving up on target file '...libxml2-2.9.12/.configured_...'.
Giving up on target file '...libxml2-2.9.12/.built'.
Giving up on target file '...stamp/.libxml2_installed'.
Giving up on target file '.compile'.
Then the package is rebuilt even if it is not otherwise needed.
To fix this, instead of always forcing the download target to be remade,
check its hash first: if it matches, then the FORCE is not added.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
In order to genererate suitable kernel headers, a 5.10 kernel tree is
prepared with a default config for mips. The arch is forced to mips in
order to avoid issues with inline asm on various architectures in a way
that doesn't involve relying on the host toolchain/headers.
It also has the advantage of supporting both endian types
Signed-off-by: Felix Fietkau <nbd@nbd.name>
ELECOM WRC-X3200GST3 uses the same header/footer as WRC-GS/GST devices
in ramips/mt7621 subtarget, so move "Build/elecom-wrc-gs-factory" to
image-commands.mk to use from mediatek/mt7622 subtarget.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Deleted (upstreamed):
bcm27xx/patches-5.10/950-0145-xhci-add-quirk-for-host-controllers-that-don-t-updat.patch [1]
Manually rebased:
bcm27xx/patches-5.10/950-0355-xhci-quirks-add-link-TRB-quirk-for-VL805.patch
bcm53xx/patches-5.10/180-usb-xhci-add-support-for-performing-fake-doorbell.patch
Note: although automatically rebaseable, the last patch has been edited to avoid
conflicting bit definitions.
[1] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=linux-5.10.y&id=b6f32897af190d4716412e156ee0abcc16e4f1e5
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
No package here depends on it. Furthermore, uClibc++ is a fairly buggy
C++ library and seems to be relatively inactive upstream.
It also lacks proper support for modern C++11 features.
The main benefit of it is size: 66.6 KB vs 287.3 KB on mips24kc. Static
linking and LTO can help bring the size down of packages that need it.
Added warning message to uclibc++.mk
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Host libraries are only build static, so let's pass --static to
pkg-config globally and remove the then unnecessary patches doing
exactly that individually.
Signed-off-by: Andre Heider <a.heider@gmail.com>
Using Host/Exports doesn't work as intended, explicitly add the
required vars so that u-boot finds the required libraries when building
its tools.
Signed-off-by: Andre Heider <a.heider@gmail.com>
DEVICE_DTS_DELIMITER needs to be in the DEFAULT_DEVICE_VARS
list to work as expected. This was missing from the original
version and got overlooked.
Fixes: fd67908647 ("scripts: mkits.sh: Allow legacy @ mode for dts creation")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Removed upstreamed:
backport-5.4/070-v5.5-MIPS-BPF-Restore-MIPS32-cBPF-JIT.patch
All other patches automatically rebased.
Signed-off-by: John Audia <graysky@archlinux.us>
Until now, this feature was switched on via the kernel configuration
option KERNEL_SECCOMP.
The follwing change a7f794cd2a now requires that
the package procd-seccomp must also enabled for buildinmg.
However, this is not the case we have no dependency and the imagebuilder
cannot build the image, because of the implicit package selection.
This change adds a new configuration option CONFIG_SECCOMP.
The new option has the same behaviour as the configuration
option CONFIG_SELINUX.
If the CONFIG_SECCOMP is selected then the package procd-seccomp and
KERNEL_SECCOMP is enabled for this build.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
While the binary `python3.10` is correctly detected by the build system
the default `python3` binary is currently not detected if pointing to a
Python 3.10 installation.
Fix this by extending the grep regex.
Signed-off-by: Paul Spooren <mail@aparcar.org>
Install ld-preload hooks allowing to add seccomp filters for arbitrary
services if kernel support for seccomp is present.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add procd-ujail to DEFAULT_PACKAGES if not building for
space-constraint (FEATURES:=small_flash) targets.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Update install procedure based on upstream feedback. Normally, meson is
to be installed with pip. But as pip is not mandated by the build
system, it cannot be used. Upstream provides a nice script to pack meson
automatically.
Moved src/ to files/. No need to copy to BUILD_DIR.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Fix Fedora 34/35 issue where 'which' detection of 'which' wasn't working
because Fedora use alias and proc
Fixup of fca5ad55d2 prereq-build: fix `which` detection on Fedora
Reported-by: Jani Partanen <rtfm@iki.fi>
Suggest-by: Etienne Champetier <champetier.etienne@gmail.com>
Tested-by: Georgi Valkov <gvalkov@abv.bg>
Signed-off-by: Paul Spooren <mail@aparcar.org>
Fix Fedora 34/35 issue where 'which' detection of 'which' wasn't working
because Fedora use alias and proc
Signed-off-by: Jani Partanen <rtfm@iki.fi>
[fix commit subject and message]
Signed-off-by: Paul Spooren <mail@aparcar.org>
Fedora 35 contains Python 3.10 as default version. Make use of it.
Signed-off-by: Marcin Juszkiewicz <marcin@juszkiewicz.com.pl>
[fix commit subject]
Signed-off-by: Paul Spooren <mail@aparcar.org>
commit 5ec60cbe9d ("scripts: mkits.sh: replace @ with - in nodes")
broke support for Meraki MR32 and this patch makes the replacement
configurable allowing for specifying the @ or - or whatever character
that is desired to retain backwards compatibility with existing devices.
For example, this patch includes the fix for the Meraki MR32 in
target/linux/bcm53xx/image for meraki_mr32:
DEVICE_DTS_DELIMITER := @
DEVICE_DTS_CONFIG := config@1
Fixes: 5ec60cbe9d ("scripts: mkits.sh: replace @ with - in nodes")
Signed-off-by: Damien Mascord <tusker@tusker.org>
[Added tags, checkpatch.pl fixes, noted that this is for old stuff]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
meson is a next generation build system designed to have good defaults,
simpler build files, and fast compilation.
It is built upon python and uses ninja for compilation. The latter
provides fast by default (parallel) and problem free compilation.
There are over 40 packages already successfully using meson. The next
commit will convert pkgconf to use meson compilation.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Multiple profiles create artifacts, these should be stored in the JSON
file as well, allowing downstream tooling to show those files, too.
Artifacts don't have specific filesystems so only the fields `name`,
`type` and `sha256` are available.
Rename env variable names from IMAGE_ to FILE_ prefixes to reflect that
images, kernels and artifacts are added with the same command.
Signed-off-by: Paul Spooren <mail@aparcar.org>
The option '-xattr' for mksquashfs4 should be '-xattrs' which lead to
build failure with SELinux enabled. Add the missing 's'.
Fixes: 4baf47b9a8 ("images: squashfs: xattrs should not depend on buld host")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
When a target configuration has unser Kconfig symbols, the build will
fail when OpenWrt is compiled with V=s and stdin is connected to a tty.
In case OpenWrt is compiled without either of these preconditions, the
build will uscceed with the symbols in question being unset.
Modify the kernel configuration in a way it fails on unset symbols
regardless of the aformentioned preconditions.
Signed-off-by: David Bauer <mail@david-bauer.net>
Enable xattr for the generated squashfs only if needed for SELinux.
This eliminates warnings during boot on target when building
(non-SELinux) OpenWrt on SELinux-enabled hosts like Fedora.
Reported-by: fda77 <fda77@users.noreply.github.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add the new CONFIG_BATTERY_RT5033 to the generic configuration, as reported by
Paul Blazejowski. Resort the kconfig while at it.
No deleted or manually refreshed patches.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
