Commit Graph

9 Commits

Author SHA1 Message Date
Adrian Schmutzler
b40e6bc55f ath79: drop and consolidate redundant chosen/bootargs
In ath79, for several SoCs the console bootargs are defined to the
very same value in every device's DTS. Consolidate these definitions
in the SoC dtsi files and drop further redundant definitions elsewhere.

The only device without any bootargs set has been OpenMesh OM5P-AC V2.
This will now inherit the setting from qca955x.dtsi

While this is a cosmetic change, backporting it to 19.07 will be a
major help for anyone doing backports of device support. Without it,
every backporter would have to remember to manually add the chosen node
to the device's DTS.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit 635f111148)
2020-06-28 14:24:59 +02:00
Petr Štetiar
6648e9458f ath79: set mib-poll-interval on mdio0 attached ar83xx switch
Commit "generic: ar8216: add mib_poll_interval switch attribute" sets
mib-poll-interval as disabled by default (was set to 2s), so it makes
switch LEDs trigger disfunctional on devices which don't have
mib-poll-interval set.

So this patch sets mib-poll-interval to 500ms on devices which have
ar83xx switch connected to mdio0 bus, as the same value was set for
built in switches in 443fc9ac35 ("ath79: use ar8216 for builtin
switch").

Some measurements performed on TP-Link Archer C7-v5:

 mib-type=0, mib-poll-interval=500ms (10s pidstat)

  Average:  %usr %system  %guest   %wait    %CPU   CPU  Command
  Average:  0.00    1.93    0.00    0.00    1.93     -  kworker/0:2

  iperf3 (30s): 334 Mbits/sec

 mib-type=0, mib-poll-interval=2s (10s pidstat)

  Average:  %usr %system  %guest   %wait    %CPU   CPU  Command
  Average:  0.00    1.14    0.00    0.00    1.14     -  kworker/0:2

  iperf3 (30s): 334 Mbits/sec

So it seems like we get 4x faster LED refresh rate for additional 0.8%
CPU load.

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-05-20 21:19:48 +02:00
Adrian Schmutzler
696e6069a4 ath79: Move settings specific for TP-Link TL-WR1043ND v4 to DTS
This prepares for support of v5.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-05-18 16:38:18 +02:00
Petr Štetiar
0d23fd2ab2 treewide: dts: Remove default-state=off property from all gpio LED nodes
>From the Documentation/devicetree/bindings/leds/common.txt:

- default-state : The initial state of the LED. Valid values are "on", "off",
  and "keep". If the LED is already on or off and the default-state property is
  set the to same value, then no glitch should be produced where the LED
  momentarily turns off (or on). The "keep" setting will keep the LED at
  whatever its current state is, without producing a glitch.  The default is
  off if this property is not present.

So setting the default-state of the LEDs to `off` is redundant as `off`
is default LED state anyway. We should remove it as almost every new
PR/patch submission contains this property by default which seems to be
just copy&paste from some DTS file already present in the tree.

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2018-12-17 08:16:28 +01:00
Petr Štetiar
bc41fb7efe ath79: Define firmware partition format to all boards where applicable
Parsing "firmware" partition (to create kernel + rootfs) was implemented
using OpenWrt downstream code enabled by CONFIG_MTD_SPLIT_FIRMWARE. With
recent upstream mtd changes we can do it in a more clean way for DTS
targets. It just requires adding a proper "compatible" string to the
"firmware" partition node.

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2018-12-06 13:28:22 +01:00
Dmitry Tunin
7a873974f7 ath79: add support for indicating the boot state using multiple leds
Use diag.sh version used for apm821xx, ipq40xx and ipq806x, which
supports different leds for the different boot states.

The existing led sequences should be the same as before.

Signed-off-by: Dmitry Tunin <hanipouspilot@gmail.com>
[reword commit message]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-08-15 07:42:36 +02:00
Mathias Kresin
55ff2951ea ath79: fix dts warnings
Fix all issues found by the devicetree compiler like wrong address/size
cells as well as wrong/missing/superfluous unit addresses.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-08-08 08:11:11 +02:00
Mathias Kresin
7b42247182 ath79: fix whitespace issue in dts files
Fixes spaces vs. tabs issues and remove indentation on blank lines.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-08-08 07:24:22 +02:00
Chuanhong Guo
8288af1e18 ath79: rename dts/image using manufacturer_board scheme
This helps getting rid of SUPPORTED_DEVICES which can be
auto-generated in image/Makefile.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2018-08-06 07:31:54 +02:00