Fixes errors in the form of:
ath10k_pci 0000:00:00.0: failed to fetch board data for bus=pci,
vendor=168c,device=0056,subsystem-vendor=0000,subsystem-device
=0000 from ath10k/QCA9888/hw2.0/board-2.bin
ath10k_pci 0000:00:00.0: failed to fetch board-2.bin or board.bin
from ath10k/QCA9888/hw2.0
ath10k_pci 0000:00:00.0: failed to fetch board file: -12
ath10k_pci 0000:00:00.0: could not probe fw (-12)
As described already in 2d3321619b ("ath79: TP-Link EAP245 v3: use
pre-calibration nvmem-cell"):
Ath10k Wave-2 hardware requires an nvmem-cell called "pre-calibration"
to load the device specific caldata, not "calibration".
Further rename the nvmem cell node and label to match the updated cell name.
Fixes: 23b9040745 ("ath79: TP-Link EAP225-Outdoor v1: convert ath10k to nvmem-cells")
Suggested-by: Sander Vanheule <sander@svanheule.net>
Signed-off-by: Nick Hainke <vincent@systemli.org>
Move the ethernet phy definition from the eap2x5-1port include to the
device-specific DTS files. This is to prepare for new devices that have
a different ethernet phy, at another MDIO address.
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Add the PCIe node for the ath10k radio to the devicetree, and refer to
the art partition for the calibration data using nvmem-cells.
Use mac-address-increment to ensure the MAC address is set correctly,
and remove the device from the caldata extraction and patching script.
Signed-off-by: Sander Vanheule <sander@svanheule.net>
TP-Link EAP225-Outdoor v1 is an AC1200 (802.11ac Wave-2) pole or wall
mount access point. Debricking requires access to the serial port, which
is non-trivial.
Device specifications:
* SoC: QCA9563 @ 775MHz
* Memory: 128MiB DDR2
* Flash: 16MiB SPI-NOR
* Wireless 2.4GHz (SoC): b/g/n 2x2
* Wireless 5GHz (QCA9886): a/n/ac 2x2 MU-MIMO
* Ethernet (AR8033): 1× 1GbE, PoE
Flashing instructions:
* ssh into target device with recent (>= v1.6.0) firmware
* run `cliclientd stopcs` on target device
* upload factory image via web interface
Debricking:
To recover the device, you need access to the serial port. This requires
fine soldering to test points, or the use of probe pins.
* Open the case and solder wires to the test points: RXD, TXD and TPGND4
* Use a 3.3V UART, 115200 baud, 8n1
* Interrupt bootloader by holding ctrl+B during boot
* upload initramfs via built-in tftp client and perform sysupgrade
setenv ipaddr 192.168.1.1 # default, change as required
setenv serverip 192.168.1.10 # default, change as required
tftp 0x80800000 initramfs.bin
bootelf $fileaddr
MAC addresses:
MAC address (as on device label) is stored in device info partition at
an offset of 8 bytes. ath9k device has same address as ethernet, ath10k
uses address incremented by 1.
From stock ifconfig:
ath0 Link encap:Ethernet HWaddr D8:...:2E
ath10 Link encap:Ethernet HWaddr D8:...:2F
br0 Link encap:Ethernet HWaddr D8:...:2E
eth0 Link encap:Ethernet HWaddr D8:...:2E
Tested by forum user PolynomialDivision on firmware v1.7.0.
UART access tested by forum user arinc9.
Signed-off-by: Sander Vanheule <sander@svanheule.net>
